Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electron density profile”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Observation of synergy between lower hybrid waves at two frequencies in EAST

Synergistic effects between two frequencies of lower hybrid (LH) waves—operating at 2.45 and 4.6 GHz—were observed in experiment on EAST for the first time. At low density (ne,lin≈2.0×1019 m−3), simultaneous injection of a 65/35 mix of 2.45/4.6 GHz power achieved an lower hybrid current drive efficiency that was 25% higher than what should be expected from the linear combination of the two sources. The experiment was interpreted with time-dependent simulations, using the equilibrium and transport solver TRANSP, coupled with the ray-tracing code GENRAY and the Fokker–Planck solver CQL3D. For each discharge, profiles of current and hard x-rays from simulation and measurement agree within uncertainties. An examination of the electron distribution function indicates that the LH synergy is supported by the increased width of the LH resonance plateau in the simultaneous injection case compared to independent injection.

Choi, W. (ORCID:0000000268912300)↗
NASA NTRS1991

A new technique to study transient conductivity under pulsed monochromatic light in Cr-doped GaAs using acoustoelectric voltage measurement

The transient conductivity of high-resistivity Bridgman-grown Cr-doped GaAs under pulsed monochromatic light is monitored using transverse acoustoelectric voltage (TAV) at 83 K. Keeping the photon flux constant, the height and transient time constant at the TAV are used to calculate the energy dependence of the trap density and its cross section, respectively. Two prominent trap profiles with peak trap densities of approximately 10 to the 17th/cu cm eV near the valence and the conduction bands are detected. These traps have very small capture cross sections in the range of 10 to the -23 to 10 to the -21st cm sq. A phenomenon similar to the persistent photoconductivity with transient time constants in excess of a few seconds in high-resistivity GaAs at T = 83 K is also detected using this technique. These long relaxation times are readily explained by the spatial separation of the photo-excited electron-hole pairs and the small capture cross section and large density of trap distribution near the conduction band.

Tabib-Azar, Massood↗
DOE OSTI2024

Ultrawide bandgap semiconductor heterojunction p–n diodes with distributed polarization-doped p-type AlGaN layers on bulk AlN substrates

Ultrawide bandgap heterojunction p–n diodes with polarization-induced AlGaN p-type layers are demonstrated using plasma-assisted molecular beam epitaxy on bulk AlN substrates. Current–voltage characteristics show a turn-on voltage of Vbi≈5.5 V, a minimum room temperature ideality factor of η≈1.63, and more than 12 orders of current modulation at room temperature. A stable current operation of the ultrawide bandgap semiconductor diode is measured up to a temperature of 300 °C. The one-sided n+–p heterojunction diode design enables a direct measurement of the spatial distribution of polarization-induced mobile hole density in the graded AlGaN layer from the capacitance–voltage profile. The measured average mobile hole density is p∼5.7×1017 cm−3, in close agreement with what is theoretically expected from distributed polarization doping. Light emission peaked at 260 nm (4.78 eV) observed in electroluminescence corresponds to interband radiative recombination in the n+ AlGaN layer. A much weaker deep-level emission band observed at 3.4 eV is attributed to cation-vacancy and silicon complexes in the heavily Si-doped AlGaN layer. These results demonstrate that distributed polarization doping enables ultrawide bandgap semiconductor heterojunction p–n diodes that have wide applications ranging from power electronics to deep-ultraviolet photonics. These devices can operate at high temperatures and in harsh environments.

Physics↗
DOE OSTI2022

Ion dynamics driven by a strongly nonlinear plasma wake

Abstract In plasma wakefield accelerators, the wave excited in the plasma eventually breaks and leaves behind slowly changing fields and currents that perturb the ion density background. We study this process numerically using the example of a Facility for Advanced aCcelerator Experimental Tests (FACET) experiment where the wave is excited by an electron bunch in the bubble regime in a radially bounded plasma. Four physical effects underlie the dynamics of ions: (1) attraction of ions toward the axis by the fields of the driver and the wave, resulting in formation of a density peak, (2) generation of ion-acoustic solitons following the decay of the density peak, (3) positive plasma charging after wave breaking, leading to acceleration of some ions in the radial direction, and (4) plasma pinching by the current generated during the wave-breaking. The interplay of these effects results in the formation of various radial density profiles, which are difficult to produce in any other way.

Physics↗
NASA NTRS1994

The effect of wave-particle interactions on the polar winds O(+)

The escape of the polar wind plasma is an important element in the ionosphere-magnetosphere coupling. Both theory and observations indicate that the wave-particle interactions (WPI) play a significant role in the dynamics of ion outflow along open geomagnetic field lines. A Monte Carlo simulation was developed in order to include the effect of the WPI in addition to the factors that are traditionally included in the 'classical' polar wind (i.e. gravity, electrostatic field, and divergence of geomagnetic field lines). The ion distribution function (f(sub j)), as well as the profiles of its moments (density, drift velocity, temperature, etc.) were found for different levels of WPI, that is, for different values of the normalized diffusion rate in the velocity space (D(tilde) (sub j perpendicular). Although the model included O(=), H(+) and eletrons, we presented only the results related to the O(+) ion. We found that (1) both the density and drift velocity of O(+) increased with the WPI strength, and consequently, the O(+) escape flux was enhanced by a factor of up to 10(exp 5), (2) The O(+) ions could be energized up to a few electron volts; (3) for moderate and high levels of WPI D(tilde) (sub perpendicular) (O(+) greater than (tilde) 1, the distribution function f(O(+)) displayed very pronounced conic features at altitudes around 3 R(sub e). Finally, the interplay between the downward body force, the upward mirror force, and the perpendicular heating resulted in the formation of the 'pressure cooker' effect. This phenomena explained some interesting features of our solution, such as, the peak in the O(=) temperature, and the formation of 'ears' and conics for f(O(+)) around 2.5 R(sub e).

Barakat, A. R.↗
DOE OSTI2025

Ion Size Effects on the Thermodynamic, Kinetic, and Mechanical Properties during Ion Exchange in Solid-State Electrolytes

Ion exchange offers a pathway to impose residual compressive stresses to mitigate the electro-chemo-mechanical cracking of solid-state electrolytes such as lithium lanthanum zirconium oxide. This study uses a coupled multiscale framework (integrating density functional theory (DFT), molecular dynamics (MD), and continuum modeling) to examine how exchange ion size influences stress, diffusion, fracture toughness, and electronic properties. Larger isovalent ions (Na + , Ag + , K + ) were exchanged with Li + , with DFT confirming their preference for octahedral 96h sites and a linear relationship between ion size and chemical free expansion coefficient. MD simulations reveal stress and concentration effects on exchange ion diffusivity at elevated temperatures, with Na + and Ag + maintaining favorable mobility while K + showing concentration-dependent clustering. Continuum modeling predicts the range of fracture strength improvements and the required ion exchange concentration profile. It was shown that a 5% surface exchange concentration can induce ∼0.6 GPa of surface compressive stress using Na + and ∼1.0 GPa of surface compressive stress using Ag + . On the other hand, larger ion exchange species may penalize Li + diffusivity by increasing the activation volume and activation energy. Interestingly, Na + has a negligible penalty on Li-ion diffusivity. The room temperature Li + ion diffusivity is reduced by ∼40% with Ag + ion exchange. Electronic band structure analysis shows no size-dependent change in the bandgap, though Ag + introduces localized defect states near the valence band maximum. This study highlights ion size as a key factor in optimizing LLZO properties, offering a framework to improve the solid-state battery performance.

Jagad, Harsh D. [Brown Univ., Providence, RI (Unit↗
NASA NTRS1976

Ultraviolet absorption lines associated with the Vela supernova remnant

Two stars behind the Vela supernova remnant and two stars offset from the remnant have been observed with the UV spectrometer aboard the Copernicus satellite. Over 200 interstellar atomic and molecular absorption features between 1000 and 1400 A have been identified and measured for radial velocity and equivalent width. In many cases, additional information was obtained by studying the detailed shapes of the recorded profiles. Most of the stars show several absorption components, with clouds of the highest radial velocity appearing in the spectra of stars behind the remnant. For each component, column densities were derived using velocity dispersion parameters which yielded the most self-consistent results. Qualitatively, the gas toward the remnant exhibits a number of unusual properties, when compared with normal interstellar material. First, abnormally high radial velocities were evident. Second, the degree of ionization of some elements suggested the existence of ionizing processes significantly more potent than those found in general regions of space. Finally, an investigation of electron densities shows that much of the gas, especially that at high velocity, must exist in the form of relatively thin sheets or filaments. If cosmic abundances prevail, the column densities of high-velocity excited material suggest that H-alpha emission measures could be as large as 100 sq cm/cu pc.

Jenkins, E. B.↗
NASA NTRS1979

Chromospheric scaling laws, width-luminosity correlations, and the Wilson-Bappu effect

Simple scaling laws for the thickness and mean electron density of stellar chromospheres as functions of surface gravity and chromospheric heating are proposed. These scaling laws are shown to be a consequence of hydrostatic equilibrium, the influence of gas ionization on plasma cooling functions, and the assumption that chromospheric heating is relatively constant with height. It is argued that line width-luminosity correlations similar to those observed in the Ca II K and Mg II k resonance lines are implied by the chromospheric scaling laws if the outer edges of the K and k emission cores are formed in the Lorentzian wings of the absorption profile. The results are compared with the Wilson-Bappu effect, empirical width-luminosity correlations for Ca II K1 minimum features, and solar-plage profiles of the Ca II K and Mg II k resonance lines.

Ayres, T. R.↗
NASA NTRS1999

Microgravity Transport Phenomena Experiment (MTPE) Overview

The Microgravity Transport Phenomena Experiment (MTPE) is a fluids experiment supported by the Fundamentals in Biotechnology program in association with the Human Exploration and Development of Space (BEDS) initiative. The MTP Experiment will investigate fluid transport phenomena both in ground based experiments and in the microgravity environment. Many fluid transport processes are affected by gravity. Osmotic flux kinetics in planar membrane systems have been shown to be influenced by gravimetric orientation, either through convective mixing caused by unstably stratified fluid layers, or through a stable fluid boundary layer structure that forms in association with the membrane. Coupled transport phenomena also show gravity related effects. Coefficients associated with coupled transport processes are defined in terms of a steady state condition. Buoyancy (gravity) driven convection interferes with the attainment of steady state, and the measurement of coupled processes. The MTP Experiment measures the kinetics of molecular migration that occurs in fluids, in response to the application of various driving potentials. Three separate driving potentials may be applied to the MTP Experiment fluids, either singly or in combination. The driving potentials include chemical potential, thermal potential, and electrical potential. Two separate fluid arrangements are used to study membrane mediated and bulk fluid transport phenomena. Transport processes of interest in membrane mediated systems include diffusion, osmosis, and streaming potential. Bulk fluid processes of interest include coupled phenomena such as the Soret Effect, Dufour Effect, Donnan Effect, and thermal diffusion potential. MTP Experiments are performed in the Microgravity Transport Apparatus (MTA), an instrument that has been developed specifically for precision measurement of transport processes. Experiment fluids are contained within the MTA fluid cells, designed to create a one dimensional flow geometry of constant cross sectional area, and to facilitate fluid filling and draining operations in microgravity. The fluid cells may be used singly for bulk solutions, or in a Stokes diaphragm configuration to investigate membrane mediated phenomena. Thermal and electrical driving potentials are applied to the experiment fluids through boundary plates located at the ends of the fluid cells. In the ground based instrument, two constant temperature baths circulate through reservoirs adjacent to the boundary plates, and establish the thermal environment within the fluid cells. The boundary plates also serve as electrodes for measurement and application of electrical potentials. The Fluid Manipulation System associated with the MTA is a computer controlled system that enables storage and transfer of experiment fluids during on orbit operations. The system is used to automatically initiate experiments and manipulate fluids by orchestrating pump and valve operations through scripted sequences. Unique technologies are incorporated in the MTA for measurement of fluid properties. Volumetric Flow Sensors have been developed for precision measurement of total fluid volume contained within the fluid cells over time. This data is most useful for measuring the kinetics of osmosis, where fluid is transported from one fluid cell to another through a semipermeable membrane. The MicroSensor Array has been designed to perform in situ measurement of several important fluid parameters, providing simultaneous measurement of solution composition at multiple locations within the experiment fluids. Micromachined sensors and interface electronics have been developed to measure temperature, electrical conductivity, pH, cation activity, and anion activity. The Profile Refractometer uses a laser optical system to directly image the fluid Index of Refraction profile that exists along the MTA fluid cell axis. A video system acquires images of the RI profile over time, and records the transport kinetics that occur upon application of chemical, thermal, or electrical driving potentials. Image processing algorithms have been developed to analyze the refractometer images on a pixel by pixel basis, calibrating and scaling the measured Index of Refraction profile to correlated solution properties of interest such as density, concentration, and temperature. Additional software has been developed to compile the processed images into a three dimensional matrix that contains fluid composition data as a function of experiment time and position in the fluid cell. These data are combined with data from the other sensor systems, and analyzed in the context of transport coefficients associated with the various transport phenomena. Analysis protocols have been developed to measure the transient kinetics, and steady state distribution of fluid components that occur in response to the applied driving potentials. The results are expressed in terms of effective transport coefficients. Experiments have been performed using a variety of solutes, and results generated are that are in agreement with published transport coefficient values.

Mason, Larry W.↗
DOE OSTI2022

Transport of an intense proton beam from a cone-structured target through plastic foam with unique proton source modeling

Laser-accelerated proton beams are applicable to several research areas within high-energy density science, including warm dense matter generation, proton radiography, and inertial confinement fusion, which all involve transport of the beam through matter. Here, we report on experimental measurements of intense proton beam transport through plastic foam blocks. The intense proton beam was accelerated by the 10 ps, 700 $\textit{J}$ OMEGA EP laser irradiating a curved foil target, and focused by an attached hollow cone. The protons then entered the foam block of density 0.38 g/cm 3 and thickness 0.55 or 1.00 mm. At the rear of the foam block, a Cu layer revealed the cross section of the intense beam via proton- and hot electron-induced Cu-K α emission. Images of x-ray emission show a bright spot on the rear Cu film indicative of a forward-directed beam without major breakup. 2D fluid-PIC simulations of the transport were conducted using a unique multi-injection source model incorporating energy-dependent beam divergence. Along with postprocessed calculations of the Cu – $K_α$ emission profile, simulations showed that protons retain their ballistic transport through the foam and are able to heat the foam up to several keV in temperature. The total experimental emission profile for the 1.0 mm foam agrees qualitatively with the simulated profile, suggesting that the protons indeed retain their beamlike qualities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1989

Characterization of hollow cathode, ring cusp discharge chambers

An experimental study into the effects of changes in such physical design parameters as hollow cathode position, anode position and ring cusp magnetic field configuration and strength on discharge chamber performance, is described. The results are presented in terms of comparative plasma ion energy cost, extracted ion fraction and ion beam profile data. Such comparisons are used to demonstrate specific means by which changes in these design parameters induce changes in performance, i.e., through changes in the loss rates of primary electrons to the anode, of ions to discharge chamber walls or of ions to cathode and anode surfaces. Results show: (1) the rate of primary electron loss to the anode decreases as the anode is moved downstream of the ring cusp toward the screen grid, (2) the loss rate of ions to hollow cathode surfaces are excessive if the cathode is located upstream of a point of peak magnetic flux density on the discharge chamber centerline, and (3) the fraction of the ions produced that are lost to discharge chamber walls and ring magnet surfaces is reduced by positioning the magnet rings so the plasma density is uniform over the grid surface and so there are no steep magnetic flux density gradients near the walls through which ions can be lost by Bohm diffusion. The uniformity of the plasma density at the grids can also be improved by moving the point of primary electron injection into the discharge chamber off of the chamber centerline. Other results show the discharge chamber losses decrease when a filament cathode is substituted for a hollow cathode to the extent of the hollow cathode operating power. When plasma ion energy cost is determined in such a way that the cost of operating the hollow cathode is subtracted out, the performance using either electron source is similar.

Vaughn, Jason A.↗
DOE OSTI2023

Degeneracy in Intercalated Pb Phases under Buffer-Layer Graphene on SiC(0001) and Diffuse Moiré Spots in Surface Diffraction

First-principles density functional theory (DFT) is used to analyze the stability of Pb intercalated phases under buffer layer graphene on SiC(0001) as a function of the supercell size, Pb coverage, and degree of Pb ordering. By comparing the chemical potentials of such two-dimensional Pb structures, here we find that there is a family of structurally distinct thermodynamically preferred Pb subsurface configurations with minute stability differences. These differences are comparable to the thermal energies at about 450 °C, where the Pb intercalated phases are grown. High-resolution surface-diffraction experiments using Spot Profile Analysis Low-Energy Electron Diffraction (SPA-LEED) confirm this high degree of degeneracy of the Pb intercalated phases from broad, low-intensity moiré spots observed exclusively from intercalated Pb. The low intensity of the moiré spots implies the coexistence of structurally different subsurface Pb phases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1994

Auroral plasma transport processes in the presence of kV potential structures

We have simulated plasma transport processes in the presence of a quasi-two-dimensional current filament, that generated kV potential structure in the auroral region. The simulation consists of a set of one-dimensional flux tube simulations with different imposed time-dependent, field-aligned currents. The model uses the 16 moment system of equations and simultaneously solves coupled continuity and momentum equations and equations describing the transport along the magnetic field lines of parallel and perpendicular thermal energy and heat flows for each species. The lower end of the simulation is at an altitude of 800 km, in the collisional topside ionosphere, while the upper end is at 10 R(sub E) in the magnetosphere. The plasma consists of hot electrons and protons of magnetospheric origin and low-energy electrons, protons, and oxygen ions of ionospheric origin. The dynamical interaction of the individual current filaments with ionospheric and magnetospheric plasma generates a potential structure in the horizontal direction and kilovolt field-aligned potential drops along the field lines. The side-by-side display exhibits the evolution of the implied potential structure in the horizontial direction. In the presence of this potential structure and parallel electric field ionospheric plasma density is depleted and velocity is reduced, while density enhancement and increased velocity is observed in magnetospheric plasma. The ionospheric and magnetospheric electron temperatures increase below 2 R(sub E) due to magnetic mirror force on converging geomagnetic field lines. The primary cross-field motion produced by the horizontal E field (E x B drift) is perpendicular to both of the significant spatial directions and is thus ignorable in this geometry. The effects of other cross-field drift processes are discussed. The simulation thus provides insight into the dynamical evolution of two-dimensional potential structures driven by an imposed finite width, field-aligned current profile.

Ganguli, Supriya B.↗
NASA NTRS2007

Current sheet Formation in a Conical Theta Pinch Faraday Accelerator with Radio-Frequency Assisted Discharge

The inductive formation of current sheets in a conical theta pinch FARAD (Faraday Accelerator with Radio-frequency Assisted Discharge) thruster is investigated experimentally with time-integrated photography. The goal is to help in understanding the mechanisms and conditions controlling the strength and extent of the current sheet, which are two indices important for FARAD as a propulsion concept. The profiles of these two indices along the inside walls of the conical acceleration coil are assumed to be related to the profiles of the strength and extent of the luminosity pattern derived from photographs of the discharge. The variations of these profiles as a function of uniform back-fill neutral pressure (with no background magnetic field and all parameters held constant) provided the first clues on the nature and qualitative dependencies of current sheet formation. It was found that there is an optimal pressure for which both indices reach a maximum and that the rate of change in these indices with pressure differs on either side of this optimal pressure. This allowed the inference that current sheet formation follows a Townsend-like breakdown mechanism modified by the existence of a finite pressure-dependent radio-frequency-generated electron density background. The observation that the effective location of the luminosity pattern favors the exit-half of the conical coil is explained as the result of the tendency of the inductive discharge circuit to operate near its minimal self-inductance. Movement of the peak in the luminosity pattern towards the upstream side of the cone with increasing pressure is believed to result from the need of the circuit to compensate for the increase in background plasma resistivity due to increasing pressure.

Hallock, Ashley K.↗
NASA NTRS2021

Machine Learning the COSMO Model for Predicting Thermodynamics of Electrolyte Mixtures

Bottom-up design of electrolyte mixtures for battery systems requires predicting macro thermodynamic properties from molecular constituents. For instance, molten salt electrolyte batteries require conditions far above room temperature to operate. Therefore, discovering mixtures with increasingly lower eutectic melting points is desirable. A model that can approximate chemical activity is a valuable tool to search through the vast compositional design space. Machine learning can predict properties of materials such as vibrational free energies, electronic energy gaps, and thermal conductivities. Moreover, they can learn physical models such as interatomic potentials. The COSMO-SAC model uses theory and empirical parameterization to predict liquid-vapor and liquid-solid properties using first-principles calculations. However, obtaining activity coefficients required for parameterizing the COSMO-SAC model is costly and limited to a select chemical space. In this work, we explored if machine learning methods could improve the COSMO-SAC model and bridge density functional theory calculations to liquid phase thermodynamic properties. Our data-driven approach uses existing databases for sigma-profiles of organic solvents and reconciles their methodological differences via ensemble averaging. First, an optimal machine learning model is constructed for each dataset. Our machine learning algorithms use the sigma-profile as an input feature to predict binary mixtures' activity coefficients using multi-output regression. Each dataset uses different choices of functionals, methods, and basis sets. Therefore, our ensemble model attempts to predict corrected activity coefficients given the combination of all the model outputs. The activity coefficients used for training are generated using the COSMO-SAC model. This approach enables the extraction of meaningful information from the existing datasets to improve the COSMO-SAC model for obtaining thermodynamic properties of electrolyte mixtures. With the liquid phase activities, we can identify electrolyte mixtures that meet desired phase equilibria conditions.

Thermodynamics↗
DOE OSTI2022

On the choice of reference orbitals for linear-response calculations of solution-phase K-edge X-ray absorption spectra

The simplest response theory methods for computing vertical excitation spectra in condensed-phase are configuration interaction with single excitations (CIS) and linear-response time-dependent density functional theory (TDDFT) within the Tamm–Dancoff approximation. In applications to X-ray absorption spectroscopy (XAS), methods like CIS and TDDFT that codify only single excitations into the wave function are prone to catastrophic errors in main-edge and post-edge features whose shapes act as a crucial fingerprint in structural analyses of liquids. Here, we show that these errors manifest primarily due to a lack of orbital relaxation in conventional linear-response theories and that core-ionized (n - 1-electron) references, like those of electron-affinity TDDFT, can eliminate the errors in the spectral profile, even in the highest-energy parts of the post-edge. Crucially, we find that single excitations atop core-ionized references are sufficient to elucidate liquid-phase XAS spectra with semi-quantitative accuracy, opening the door for methods like electron-affinity CIS/TDDFT to be used as efficient alternatives to higher-order wave function approaches.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Annihilation-gamma-based diagnostic techniques for magnetically confined electron–positron pair plasma

Efforts are underway to magnetically confine electron–positron pair plasmas to study their unique behaviour, which is characterized by significant changes in plasma time and length scales, supported waves and unstable modes. However, use of conventional plasma diagnostics presents challenges with these low-density and annihilating matter–antimatter plasmas. To address this problem, we propose to develop techniques based on the distinct emission provided by annihilation. This emission exhibits two spatial correlations: the distance attenuation of isotropic sources and the back-to-back propagation of momentum-preserving 2 $\gamma$ annihilation. We present the results of our analysis of the $\gamma$ emission rate and the spatial profile of the annihilation in a magnetized pair plasma from direct pair collisions, from the formation and decay of positronium as well as from transport processes. In order to demonstrate the effectiveness of annihilation-based techniques, we tested them on annular $\gamma$ emission profiles produced by a $\beta ^+$ radioisotope on a rotating turntable. Direct and positronium-mediated annihilation result in overlapping volumetric $\gamma$ sources, and the 2 $\gamma$ emission from these volumetric sources can be tomographically reconstructed from coincident counts in multiple detectors. Transport processes result in localized annihilation where field lines intersect walls, limiters or internal magnets. These localized sources can be identified by the fractional $\gamma$ counts on spatially distributed detectors.

Physics↗
NASA NTRS2015

The Time-Dependent Chemistry of Cometary Debris in the Solar Corona

Recent improvements in solar observations have greatly progressed the study of sungrazing comets. They can now be imaged along the entirety of their perihelion passage through the solar atmosphere, revealing details of their composition and structure not measurable through previous observations in the less volatile region of the orbit further from the solar surface. Such comets are also unique probes of the solar atmosphere. The debris deposited by sungrazers is rapidly ionized and subsequently influenced by the ambient magnetic field. Measuring the spectral signature of the deposited material highlights the topology of the magnetic field and can reveal plasma parameters such as the electron temperature and density. Recovering these variables from the observable data requires a model of the interaction of the cometary species with the atmosphere through which they pass. The present paper offers such a model by considering the time-dependent chemistry of sublimated cometary species as they interact with the solar radiation field and coronal plasma. We expand on a previous simplified model by considering the fully time-dependent solutions of the emitting species' densities. To compare with observations, we consider a spherically symmetric expansion of the sublimated material into the corona and convert the time-dependent ion densities to radial profiles. Using emissivities from the CHIANTI database and plasma parameters derived from a magnetohydrodynamic simulation leads to a spatially dependent emission spectrum that can be directly compared with observations. We find our simulated spectra to be consistent with observation.

sun: corona↗