SEARCH · Engineering Papers

Results for “edge effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Use of a liquid-crystal, heater-element composite for quantitative, high-resolution heat transfer coefficients on a turbine airfoil, including turbulence and surface roughness effects

Local heat transfer coefficients were measured along the midchord of a three-times-size turbine vane airfoil in a static cascade operated at roon temperature over a range of Reynolds numbers. The test surface consisted of a composite of commercially available materials: a Mylar sheet with a layer of cholestric liquid crystals, which change color with temperature, and a heater made of a polyester sheet coated with vapor-deposited gold, which produces uniform heat flux. After the initial selection and calibration of the composite sheet, accurate, quantitative, and continuous heat transfer coefficients were mapped over the airfoil surface. Tests were conducted at two free-stream turbulence intensities: 0.6 percent, which is typical of wind tunnels; and 10 percent, which is typical of real engine conditions. In addition to a smooth airfoil, the effects of local leading-edge sand roughness were also examined for a value greater than the critical roughness. The local heat transfer coefficients are presented for both free-stream turbulence intensities for inlet Reynolds numbers from 1.20 to 5.55 x 10 to the 5th power. Comparisons are also made with analytical values of heat transfer coefficients obtained from the STAN5 boundary layer code.

Hippensteele, Steven A.↗

NASA NTRS1987

An experimental investigation of dynamic ground effect

Sixty degree delta wing, F-106B, and XB-70 models with and without flap deflections were tested in static and dynamic ground effect in the 36 by 51 inch subsonic wind tunnel at the University of Kansas. Dynamic ground effect was measured with movable sting support. For flow visualization, a tufted wire grid was mounted on the movable sting behind the model. Tests results showed that the lift and drag increments in dynamic ground effect were always lower than the static values. Effect of the trailing-edge flap deflections on lift increments was slight. The fuselage reduced the lift increments at a given ground height. From flow visualization under static conditions, the vortex core was seen to enlarge as the ground approached.

Lee, Pai Hung↗

NASA NTRS1986

Semiconductor superlattice photodetectors

Technical progress made in the study of superlattice photoconductors is summarized and papers submitted for publication are listed. Since the quantum-well regions may contain several subbands, each of which may be occupied by electrons depending on the doping concentrations, it is important to include the multi-subbands in calculating the impact ionization rate. The electrons occupying the higher subbands require a smaller amount of energy to get out of the quantum well; thus, those higher level subband electrons contribute significantly to the impact ionization rate. The results of the subbands have been calculated. Results concerning the nonparabolicity effect of the band structure, the effect of the quantum-well size, and the effect of the band-edge discontinuity and doping are also summarized.

Chuang, S. L.↗

NASA NTRS1986

Exploratory wind-tunnel investigation of the stability and control characteristics of advanced general aviation configurations

Results of low-speed wind-tunnel investigations are presented for two general aviation configurations: the AVTEK canard configuration and the DeVore conventional configuration. Cooperative research programs were undertaken by industry and NASA to jointly conduct tests in the NASA Langley 12-Foot Low-Speed Wind Tunnel to explore stability and control characteristics of each configuration. A 1/5-scale AVTEK model and a 1/6-scale DeVore model were tested over an angle-of-attack range of up to 45 deg and an angle-of-sideslip range of up to 20 deg. Results from the AVTEK test are presented with an emphasis on the effects of configuration on the stall and poststall characteristics. Results from the DeVore test are presented with emphasis on the effects of wing leading-edge droop design on spin resistance characteristics.

Yip, L. P.↗

NASA NTRS1986

Rotor/wing aerodynamic interactions in hover

An experimental and theoretical investigation of rotor/wing aerodynamic interactions in hover is described. The experimental investigation consisted of both a large-scale and small-scale test. A 0.658-scale, V-22 rotor and wing was used in the large-scale test. Wind download, wing surface pressure, rotor performance, and rotor downwash data from the large-scale test are presented. A small-scale experiment was conducted to determine how changes in the rotor/wing geometry affected the aerodynamic interactions. These geometry variations included the distance between the rotor and wing, wing incidence angle, and configurations both with the rotor axis at the tip of the wing (tilt rotor configuration) and with the rotor axis at the center of the wing (compound helicopter oonfiguration). A wing with boundary-layer control was also tested to evaluate the effect of leading and trailing edge upper surface blowing on the wing download. A computationally efficient, semi-empirical theory was developed to predict the download on the wing. Finally, correlations between the theoretical predictions and test data are presented.

Felker, F. F.↗

NASA NTRS1987

Use of a liquid-crystal and heater-element composite for quantitative, high-resolution heat-transfer coefficients on a turbine airfoil including turbulence and surface-roughness effects

Local heat transfer coefficients were measured along the midchord of a three-times-size turbine vane airfoil in a static cascade operated at room temperature over a range of Reynolds numbers. The test surface consisted of a composite of commercially available materials: a Mylar sheet with a layer of cholestric liquid crystals, which change color with temperature, and a heater made of a polyester sheet coated with vapor-deposited gold, which produces uniform heat flux. After the initial selection and calibration of the composite sheet, accurate, quantitative, and continuous heat transfer coefficients were mapped over the airfoil surface. Tests were conducted at two free-stream turbulence intensities: 0.6 percent, which is typical of wind tunnels; and 10 percent, which is typical of real engine conditions. In addition to a smooth airfoil, the effects of local leading-edge sand roughness were also examined for a value greater than the critical roughness. The local heat transfer coefficients are presented for both free-stream turbulence intensities for inlet Reynolds numbers from 1.20 to 5.55 x 10 to the 5th power. Comparisons are also made with analytical values of heat transfer coefficients obtained from the STAN5 boundary layer code.

Hippensteele, S. A.↗

NASA NTRS1988

Flow control in a wing/fuselage-type juncture

The laminar flow around a juncture formed by an unswept wing and a flat plate has been studied using a combination of smoke flow visualization, and velocity and pressure measurements. The effectiveness of swept leading-edge fillets in controlling the juncture flow field has been evaluated. Flow separation upstream of the wing leading edge is confined to a small region near the plate. This separation results in periodic shedding of horseshoe type vortices. The pressure gradient measured upstream of the leading edge in this laminar juncture is steeper than that of the turbulent flow case. The use of fillets eliminates the leading-edge flow separation and reduces the size of juncture wake, as observed from flow visualization. For one of the filleted cases, there is a significant increase in the extent of laminar flow in the juncture region, and a sizable reduction in the juncture drag.

Kubendran, L. R.↗

NASA NTRS1988

Analysis of coupled cylindrical striplines filled with multilayered dielectrics

A method of analysis for coupled cylindrical striplines filled with multilayered dielectrics is presented that uses a variational technique in the space domain. Coupled-mode analysis is presented for the case of a pair of coupled circular arc strips arbitrarily located between cylindrical ground planes filled with multilayered dielectrics. An even- and odd-mode approach is used for the analysis of shielded cylindrically curved edge-coupled pairs of broad-side parallel strips (broad-side, edge-coupled cylindrical striplines). The effect of environmental changes on an otherwise planar structure is also studied by extending the present analysis to cylindrically warped coupled striplines.

Reddy, C. Jagadeswara↗

NASA NTRS1990

Predicting Noise From Wind Turbines

Computer program WINDY predicts broadband noise spectra of horizontal-axis wind-turbine generators. Enables adequate assessment of impact of broadband wind-turbine noise. Effects of turbulence, trailing-edge wakes, and bluntness taken into account. Program has practical application in design and siting of wind-turbine machines acceptable to community. Written in GW-Basic.

Grosveld, Ferdinand W.↗

NASA NTRS1990

Wing-Design And -Analysis Code

WINGDES2 computer program provides wing-design algorithm based on modified linear theory taking into account effects of attainable leading-edge thrust. Features improved numerical accuracy and additional capabilities. Provides analysis as well as design capability and applicable to both subsonic and supersonic flow. Replaces earlier wing-design code designated WINGDES (see LAR-13315). Written in FORTRAN V.

Darden, Christine M.↗

NASA NTRS1991

CFD validation of a supersonic laminar flow control concept

A three-dimensional Navier-Stokes code is used in conjunction with a linear compressible stability analysis code to develop a numerical procedure for prediction of laminar flow transition. The procedure is applied to a modified F-16XL fighter with a laminar flow control glove at supersonic speed. Details of boundary layer stability analysis indicate that, computationally, laminar flow could be realized on the highly swept wing in the absence of the leading edge attachment-line contamination. Effects of the three-dimensionality of the flow were shown to be important in the boundary layer stability analysis. The numerically predicted surface pressures compare favorably with the flight test data.

Woan, Chung-Jin↗

NASA NTRS1990

Instability of fiber-reinforced viscoelastic composite plates to in-plane compressive loads

This study analyzes the stability behavior of unidirectional fiber-reinforced composite plates with viscoelastic material behavior subject to in-plane biaxial compressive edge loads. To predict the effective time-dependent material properties, elastic fibers embedded in a linearly viscoelastic matrix are examined. The micromechanical relations developed for a transversely isotropic medium are discussed along with the correspondence principle of linear viscoelasticity. It is concluded that the stability boundary obtained for a viscoelastic plate is lower (more critical) than its elastic counterpart, and the transverse shear deformation effects are more pronounced in viscoelastic plates than in their elastic counterparts.

Chandiramani, N. K.↗

NASA NTRS1992

RCS reduction of a microstrip patch using lumped loads

In this report we consider the radar cross section (RCS) of a single rectangular patch antenna in a recessed cavity. Using a previously developed finite element-boundary integral method code, a study is performed on the patch's RCS as a function of frequency. To reduce the RCS of the patch at the resonant frequency, lumped (resistive) loads are placed at the edges of the patch. The effects of the lumped loads on the patch's RCS and gain are examined and it is observed that the RCS and gain are reduced as the as the load value decreases, whereas the antenna's bandwidth is increased. At resonance, the usual relations between the RCS and gain is observed, but it is shown that this relation no longer holds at frequencies away from resonance.

Volakis, John L.↗

NASA NTRS1992

Low-speed longitudinal and lateral-directional aerodynamic characteristics of the X-31 configuration

An experimental investigation of a 19 pct. scale model of the X-31 configuration was completed in the Langley 14 x 22 Foot Subsonic Tunnel. This study was performed to determine the static low speed aerodynamic characteristics of the basic configuration over a large range of angle of attack and sideslip and to study the effects of strakes, leading-edge extensions (wing-body strakes), nose booms, speed-brake deployment, and inlet configurations. The ultimate purpose was to optimize the configuration for high angle of attack and maneuvering-flight conditions. The model was tested at angles of attack from -5 to 67 deg and at sideslip angles from -16 to 16 deg for speeds up to 190 knots (dynamic pressure of 120 psf).

Banks, Daniel W.↗

NASA NTRS1931

A comparison of the aerodynamic characteristics of the normal and three reflexed airfoils in the variable density wind tunnel

An investigation was made of the aerodynamic effects of reflexing the trailing edge of three commonly used airfoils. Six airfoils were used in the investigation: three having the normal profiles of the Navy 60, the Boeing 106, and the Gottingen 398, and three having these profiles modified to obtain a reflexed trailing edge with the mean camber line changed to give Cmc/4=0. The tests were conducted at a value of the Reynolds Number of approximately 3,100,000 in the variable density wind tunnel of the National Advisory Committee for Aeronautics. Measurements of lift, drag, and pitching moment were made on each of the six airfoils. The expected reduction of the center of pressure travel was obtained. The maximum lift was reduced approximately 12 per cent and the minimum profile drag approximately 4 per cent.

Defoe, George L↗

NASA NTRS1956

Investigation of the Effectiveness of Boundary-layer Control by Blowing over a Combination of Sliding and Plain Flaps in Deflecting a Propeller Slipstream Downward for Vertical Take-off

An investigation was conducted in order to determine the effectiveness of blowing a jet of air over the flaps of a wing equipped with a 50-percent-chord sliding flap and a 25-percent-chord plain flap in deflecting a propeller slipstream downward for vertical take-off and the results are presented herein. The effects of a leading-edge slat, ground proximity, end plate, and propeller position were also investigated. The tests were conducted in a static-thrust facility at the Langley Aeronautical Laboratory.

AIRPLANES - PERFORMANCE↗

NASA NTRS1994

Slush Hydrogen Technology Program

A slush hydrogen (SH2) technology facility (STF) was designed, fabricated, and assembled by a contractor team of McDonnell Douglas Aerospace (MDA), Martin Marietta Aerospace Group (MMAG), and Air Products and Chemicals, Inc. (APCI). The STF consists of a slush generator which uses the freeze-thaw production process, a vacuum subsystem, a test tank which simulates the NASP vehicle, a triple point hydrogen receiver tank, a transfer subsystem, a sample bottle, a pressurization system, and a complete instrumentation and control subsystem. The STF was fabricated, checked-out, and made ready for testing under this contract. The actual SH2 testing was performed under the NASP consortium following NASP teaming. Pre-STF testing verified SH2 production methods, validated special SH2 instrumentation, and performed limited SH2 pressurization and expulsion tests which demonstrated the need for gaseous helium pre-pressurized of SH2 to control pressure collapse. The STF represents cutting-edge technology development by an effective Government-Industry team under very tight cost and schedule constraints.

Cady, Edwin C.↗

NASA NTRS1994

MHD modeling of magnetotail instability for localized resistivity

We present results of a three-dimensional magnetohydrodynamic (MHD) simulation of magnetotail evolution initiated by a sudden occurrence or increase of spatially localized resistivity as the major expected concequence of some localized microinstability. Because of the absence of a quantitative model, possible variations of resistivity levels with current density, or the reduction thereof, are not incorporated in the present investigation. The emphasis of the study is on an investigation of the changes to the overall evolution brought about by this localization, in particular, on the disruption and diversion of the cross-tail current and the nonlinear evolution of the magnetotail instability. The immediate consequences of the occurrence of the localized resistance and the resulting electric field are a reduction and diversion of the electric current around the region of high resistivity, associated with an increase of B(sub z) ('dipolarization') at the earthward edge and a decrease of B(sub z) at the tailward edge of this region. These effects, however, are localized and do not involve a reduction of the total cross-tail current and hence do not lead to the global development of a 'substorm current wedge,' which includes not only the reduction of the cross-tail current but also the buildup of a global field-aligned current system of 'regional 1' type (toward the Earth on the dawnside and away on the duskside of the tail). Such signatures develop at a later time, as consequences of a three-dimensional tearing instability, which is triggered by the occurrence of the resistivity. These features are found in combination with plasmoid formation and ejection, quite similar to results of earlier simulations with uniform resistivity. Differences are found in the timescale of the evolution, which tends to be shorter for localized resistivity, and in the propagation of the dipolarization effects in the equatorial plane. Whereas for uniform resistivity the temporal increase in B(sub z) tends to propagate tailward, apparently due to a pileup effect in the near-Earth region, an earthward propagation is found for the localized resistivity. This propagation results from an earthward convection of the gradient in B(sub z), which is set up by the reconnection process further tailward.

Hesse, Michael↗