SEARCH · Engineering Papers

Results for “direct current”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

All sources NASA NTRS DOE OSTI

NASA NTRS1972

Storm time instabilities of the ring current.

Demonstration that the resonant cyclotron instability between radiation belt protons and ion-cyclotron waves can account for many observed features of the magnetospheric ring current. Analogous results apply to the electron-whistler interaction although the former are not considered to be important for ring current energetics. Particles with energy exceeding 100 keV are readily destabilized throughout the entire magnetosphere and their fluxes are consequently limited to the stably trapped levels described by Kennel and Petschek (1966). However, at the dominant ring current energies between 10 and 100 keV, a broad zone of stability exists in the region just outside the plasmapause. Particles injected into this outer zone during substorms may remain trapped for many drift orbits allowing an intense ring current to develop. In direct contrast, this stable ring current zone is bounded by regions of rapid precipitational loss within the plasmasphere and at large radial distance in the auroral zone.

Thorne, R. M.↗

NASA NTRS1975

Preliminary measurements of plasma fluctuations in an 8-cm mercury ion thruster

The rms magnitude, spectra, and cross correlations for the fluctuations in the beam current, the neutralizer keeper current, and the discharge current and voltage were measured for an 8-cm diameter, dished grid ion thruster for a beam current of 72 milliamps. The ratio of the rms magnitude of the fluctuations to the time-mean neutralizer keeper current was found to depend significantly on the neutralizer time-mean keeper current, the flow rate, and keeper hold diameter. The maxima of the spectra of the beam current fluctuations did not depend on the discharge fluctuations. It was found that: (1) the discharge current fluctuations do not directly contribute to the beam current fluctuations; and (2) the neutralizer contributions to the beam fluctuations are small (for good neutralizer-to-beam coupling) but not negligible and appear mostly in the higher frequency range measured.

Serafini, J. S.↗

DOE OSTI2025

Sub-MeV dark sink dark matter

A dark sink uses dark-sector interactions to siphon energy from dark matter to lighter dark degrees of freedom, i.e., dark radiation. Here, we extend dark matter models containing a dark sink to sub-MeV masses. We consider a dark sink model where the dark matter is charged under a light dark photon that has kinetic mixing with the Standard Model. For sub-MeV dark matter masses, plasmon decays are the dominant mechanism for transferring energy to the dark sector. Relative to a standard freeze-in cosmology, reproducing the observed dark matter density in a dark sink structure requires an increase in the dark matter couplings to the Standard Model, and hence increased direct detection cross sections. These models provide benchmarks for current and upcoming direct detection experiments. Accounting for plasmon effects, we derive the range of possible dark matter masses and cross sections for dark sink models in the sub-MeV regime. We make the freezein code available to reproduce our benchmarks; it may be of use for other freeze-in scenarios, including those where plasmon decays to the dark matter are important.

Dark matter detectors↗

NASA NTRS1995

The direction of heat flow in an expanding current free stellar atmosphere

The energy budgets of the corona are substantially influenced by losses attributed to thermal conduction losses down the transition region, towards the chromosphere. Although Fourier law for such a plasma regime is now universally criticized as inappropriate, the direction of this heat flow seems to be certain. The purpose of this paper is to point out, based on conservation laws, the direction in which the heat must flow in this regime, provided it is known that there is a time independent expansion devoid of parallel currents. It will be argued that the direction of the heat flux is from the base of the transition region up into the corona, rather than the opposite. Under the circumstances mentioned above, the direction of the heat flow should be opposite to the gradient of the electron pressure gradient. Although the transition region is modeled as isobaric, this is only approximately true. Such a likely scenario makes the heat flow almost certainly to flow from the lower temperature base of the TR up into the incipient corona if a steady state current free expansion is to be maintained.

Scudder, J. D.↗

NASA NTRS1971

Rocket-based measurement of Birkeland currents related to an auroral arc and electrojet.

A rocket-borne experiment performed to study currents associated with a quiet auroral arc is discussed. The magnetic field in the vicinity of the arc was measured with a vector magnetometer, while the orientation of the payload was determined with a lunar-aspect sensor. Possible current configurations were inferred by constructing model current systems that reproduced the magnetic field variations measured along the flight path. The data are interpreted in terms of a model current system consisting of a northwestward electrojet and two oppositely directed Birkeland sheet currents, all lying in planes approximately parallel to the auroral arc. The current density integrated through the 16-km thickness of each Birkeland current sheet was found to be roughly 0.16 A/m. The electrojet current was roughly 6000 A.

Park, R. J.↗

DOE OSTI2022

Ultracapacitors with high frequency response

An electric double layer capacitor (EDLC) is disclosed including: a first electrode including a first current collector and first plurality of carbon nanotubes (CNTs) disposed substantially directly upon the first current collector; a second electrode comprising a second current collector and second plurality of CNTs disposed substantially directly upon the second current collector; and an electrolyte disposed between and in contact with (e.g., wetting) the first and second electrodes. In some embodiments, the EDLC is configured to have a capacitive frequency window comprising about 1 Hz to about 50 Hz.

Brambilla, Nicolò Michele↗

DOE OSTI2021

Current status of biogas upgrading for direct biomethane use: A review

Anaerobic digestion produces biogas, a mixture of CH 4 and CO 2 , where CH 4 is a low cost, environmentally friendly, and renewable energy source. The application of biogas production is increasing rapidly as a means of reducing the pollution impact of organic biomasses. However, biogas contains unwanted elements such as hydrogen sulfide, carbon monoxide, siloxanes, and carbon dioxide. To remove these elements, several biogas upgrading technologies like water scrubbing, amine scrubbing, pressure swing adsorption, and membrane separation have been developed and are being used at various commercial scales. Problems with these methods are high energy consumption, the use of expensive chemicals, and high operating cost. Therefore, a major effort is currently underway to improve the design of existing methods as well as developing innovative new upgrading technologies such as cryogenic separation and biological upgrading. Here, this review intends to provide a comprehensive overview of the limitations with the existing upgrading technologies along with recent advances in physical, chemical, and biological biogas upgrading technologies (e.g., pressure swing adsorption, membrane separation, biochar adsorption and CO 2 conversion by biological organisms) and further into possible future solutions, such as hybrid systems. Comparative studies of process complexities and associated economic concerns are also provided, and future perspectives that may facilitate research into sustainable biogas upgrading technologies are discussed, focusing in particular on cryogenic separation, novel biological techniques, biochar based upgrading and hybrid technologies incorporating two or more different methods seamlessly integrated.

09 BIOMASS FUELS↗

NASA NTRS1994

Regulator Circuit For Bilateral Source/Load Power System

Circuit regulates output voltage whether current flows from left source/load to right load/source or vice versa. Overall system characterized as voltage-controlled current source with bilateral current capability. Additional feature of control circuit is that maximum current in either direction limited by limiting excursion of output voltage from zero-current value. Thus, external current-limiting circuitry not necessary.

Madden, George↗

DOE OSTI2023

Direct air capture of CO2: from insights into the current and emerging approaches to future opportunities

The rapid development of direct air capture (DAC) technologies has become critical in order to remove CO 2 from the atmosphere and limit global warming to a maximum of 1.5°C. In this perspective, we provide a mini review of the current research on the emerging liquid- and solid-based sorbent materials to capture CO 2 , summarize the existing challenges of DAC technologies, and suggest future research directions to accelerate the development of DAC systems. In particular, the desired properties for a breakthrough sorbent that efficiently captures CO 2 from the air and releases it for sequestration are described.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Urbanization Impact on Regional Climate and Extreme Weather: Current Understanding, Uncertainties, and Future Research Directions

Abstract Urban environments lie at the confluence of social, cultural, and economic activities and have unique biophysical characteristics due to continued infrastructure development that generally replaces natural landscapes with built-up structures. The vast majority of studies on urban perturbation of local weather and climate have been centered on the urban heat island (UHI) effect, referring to the higher temperature in cities compared to their natural surroundings. Besides the UHI effect and heat waves, urbanization also impacts atmospheric moisture, wind, boundary layer structure, cloud formation, dispersion of air pollutants, precipitation, and storms. In this review article, we first introduce the datasets and methods used in studying urban areas and their impacts through both observation and modeling and then summarize the scientific insights on the impact of urbanization on various aspects of regional climate and extreme weather based on more than 500 studies. We also highlight the major research gaps and challenges in our understanding of the impacts of urbanization and provide our perspective and recommendations for future research priorities and directions.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1978

Direct measurements of the atmospheric conduction current

A method of measuring the atmospheric conduction current above the ground has been employed to obtain data for 12 weeks during the first half of 1974. The instrument consists of a split aluminum sphere suspended by insulated wires to a wooden frame. The measuring electronics and the transmitter are enclosed within the spherical structure. The interaction of the instrument with its atmospheric electrical environment is analyzed, and it is shown that in steady state conditions, predictable differences in the instrumentally measured currents and the atmospheric conduction current will be less than 5% and in the nonsteady state situations the difference is less than 20%. Diurnal variations, a probable winter-summer variation, sunrise, and fog effects were observed for the data obtained during fair-weather conditions. Disturbed weather data are interpreted for the effects of low clouds on the atmospheric current. The charge concentrations within overcast clouds sufficient to produce the observed reversed atmospheric currents are estimated to be small in relation to values in thunderclouds.

Burke, H. K.↗

NASA NTRS1990

Multiple strike slip faults sets: A case study from the Dead Sea transform

In many strike slip tectonic settings, large rotations of crust blocks about vertical axes have been inferred from paleomagnetic data. These blocks are bounded by sets of parallel faults which presumably accommodate the relative motion between the blocks as regional deformation progress. A mechanical model by Nur et al., (1986) suggests that rotations greater than phi sub c equals 25 to 45 degrees must be accommodated by more than one set of faults, with angle phi sub c between their direction; consequently the sum of the angles between sets must be roughly equal to the total tectonic material rotation. To test this model, the authors investigated the fault geometry and field relation of fault sets in the Mt. Hermon area in northern Israel, where paleomagnetic declination implies data 69 degrees plus or minus 13 degrees counter-clockwise block rotation. The statistical and field relation analysis of over 315 faults shows that the faulting is predominantly right lateral strike slip consisting of three distinct sets. The oldest set strikes 253 degrees, the second oldest set strikes 293 degrees and the youngest strikes 339 degrees. This last direction is consistent also with the current north-south direction of the maximum principle stress axis. The angle phi sub c between the first and second sets is 39 degrees and between the second and third sets 46 degrees, in good agreement with the phi sub c angle predicted from mechanical considerations. The sum of the two angles is 85 degrees, in good agreement with the 69 degrees plus or minus 13 degrees CCW paleomagnetically derived rotation. The results suggest specifically that the sequential development of multiple intersecting fault sets is responsible for the faulting in the Mt. Hermon area; and generally that the model of block rotation with multiple faults provides very good simple rules for analyzing very complex fault patterns.

Ron, Hagai↗

NASA NTRS1992

Current status and some future test directions for the U.S. National Transonic Facility

The construction of the National Transonic Facility was completed in September 1982 and the start-up and checkout of the tunnel systems were performed over the following two years. In August 1984, the facility was declared operational for final checkout of cryogenic instrumentation and control systems, and for the aerodynamics calibration and testing to commence. Since 1984 several operational problems have been identified and successfully solved which is demonstrated by the fact that the facility has operated the last year with no significant facility down times. Also during this time period, development of test techniques and instrumentation has continued. This paper will review some of the recent test techniques and instrumentation developments, and will briefly review the status of the facility.

Gloss, Blair B.↗

NASA NTRS2003

Scanning Tunneling Optical Resonance Microscopy

Scanning tunneling optical resonance microscopy (STORM) is a method, now undergoing development, for measuring optoelectronic properties of materials and devices on the nanoscale by means of a combination of (1) traditional scanning tunneling microscopy (STM) with (2) tunable laser spectroscopy. In STORM, an STM tip probing a semiconductor is illuminated with modulated light at a wavelength in the visible-to-near-infrared range and the resulting photoenhancement of the tunneling current is measured as a function of the illuminating wavelength. The photoenhancement of tunneling current occurs when the laser photon energy is sufficient to excite charge carriers into the conduction band of the semiconductor. Figure 1 schematically depicts a proposed STORM apparatus. The light for illuminating the semiconductor specimen at the STM would be generated by a ring laser that would be tunable across the wavelength range of interest. The laser beam would be chopped by an achromatic liquid-crystal modulator. A polarization-maintaining optical fiber would couple the light to the tip/sample junction of a commercial STM. An STM can be operated in one of two modes: constant height or constant current. A STORM apparatus would be operated in the constant-current mode, in which the height of the tip relative to the specimen would be varied in order to keep the tunneling current constant. In this mode, a feedback control circuit adjusts the voltage applied to a piezoelectric actuator in the STM that adjusts the height of the STM tip to keep the tunneling current constant. The exponential relationship between the tunneling current and tip-to-sample distance makes it relatively easy to implement this mode of operation. The choice of method by which the photoenhanced portion of the tunneling current would be measured depends on choice of the frequency at which the input illumination would be modulated (chopped). If the frequency of modulation were low enough (typically < 10 Hz) that the feedback circuit could respond, then the voltage applied to the piezoelectric tip-height actuator could be measured by use of a lock-in amplifier locked to the modulation (chopping) signal. However, at a high modulation frequency (typically in the kilohertz range or higher), the feedback circuit would be unable to respond. In this case, the photoenhanced portion of the tunneling current could be measured directly. For this purpose, the tunneling current would be passed through a precise resistor and the voltage drop would be measured by use of the lock-in amplifier.

Bailey, Sheila↗

NASA NTRS2002

Acoustically Enhanced Electroplating Being Developed

In cooperation with the NASA Glenn Research Center, Alchemitron Corp. is developing the Acoustically Enhanced Electroplating Process (AEEP), a new technique of employing nonlinear ultrasonics to enhance electroplating. The applications range from electroplating full-panel electronic circuit boards to electroplating microelectronics and microelectromechanical systems (MEMS) devices. In a conventional plating process, the surface area to be plated is separated from the nonplated areas by a temporary mask. The mask may take many forms, from a cured liquid coating to a simple tape. Generally, the mask is discarded when the plating is complete, creating a solid waste product that is often an environmental hazard. The labor and materials involved with the layout, fabrication, and tooling of masks is a primary source of recurring and nonrecurring production costs. The objective of this joint effort, therefore, is to reduce or eliminate the need for masks. AEEP improves selective plating processes by using directed beams of high-intensity acoustic waves to create nonlinear effects that alter the fluid dynamic and thermodynamic behavior of the plating process. It relies on two effects: acoustic streaming and acoustic heating. Acoustic streaming is observed when a high-intensity acoustic beam creates a liquid current within the beam. The liquid current can be directed as the beam is directed and, thus, users can move liquid around as desired without using pumps and nozzles. The current of the electroplating electrolyte, therefore, can be directed at distinct target areas where electroplating is desired. The current delivers fresh electrolyte to the target area while flushing away the spent electrolyte. This dramatically increases the plating rate in the target area. In addition, acoustic heating of both the liquid in the beam and the target surface increases the chemical reaction rate, which further increases the plating rate. The combined effects of acoustic streaming and heating accelerate the deposition of plating in that area and, thus, provide an effect similar to a mask but without the costs of masking. AEEP further improves the plating process by clearing debris and bubbles from the surface by acoustic radiation pressure and acoustic streaming.

Oeftering, Richard C.↗

NASA NTRS1969

A simple electrometer for measuring small photoelectric currents

Quartz-fiber direct-indicating pocket dosimeter is a small-current integrating electrometer. By attaching the photocathode to the quartz fiber terminal and the photoelectron collector to the barrel of the dosimeter and by charging the device to 150 V, a small-current measuring device can be achieved.

Source record↗

DOE OSTI2021

Reversible ratchet effects in a narrow superconducting ring

We study the ratchet effect in a narrow pinning-free superconductive ring based on time-dependent GinzburgLandau (TDGL) equations. Voltage responses to external dc and ac currents at various magnetic fields are studied. Due to asymmetric barriers for flux penetration and flux exit in the ring-shaped superconductor, the critical current above which the flux-flow state is reached, as well as the critical current for the transition to the normal state, are different for the two directions of applied current. Furthermore, these effects cooperatively cause ratchet signal reversal at high magnetic fields, which has not been reported to date in a pinning-free system. The ratchet signal found here is larger than those induced by asymmetric pinning potentials. Our results also demonstrate the feasibility of using mesoscopic superconductors to employ a superconducting diode effect in versatile superconducting devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA NTRS1981

Japanese Magsat Team. A: Crustal structure near Japan and its Antarctic Station. B: Electric currents and hydromagnetic waves in the ionosphere and the magnetosphere

Efforts continue in compiling tapes which contain vector and scalar data decimated at an interval of 0.5 sec, together with time and position data. A map of the total force field anomaly around Japan was developed which shows a negative magnetic anomaly in the Okhotsk Sea. Examination of vector residuals from the MGST model shows that the total force perturbation is almost ascribable to the perturbation parallel to the main geomagnetic field and that the contribution from the perturbation transverse to the main field to the total force perturbation is negligibly small. The influences of ionospheric current with equatorial electroject and of the magnetospheric field aligned current on the dawn-dusk asymmetry of daily geomagnetic variations are being considered. The total amount of electric current flowing through the plane of the Magsat orbit loop was calculated by direct application of Maxwell's equation. Results show that the total electric current is 1 to 5 ampheres, and the current direction is either sunward or antisunward.

Fukushima, N.↗