Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cathodes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Direct Observation of Defect‐Aided Structural Evolution in a Nickel‐Rich Layered Cathode

Abstract Ni‐rich LiNi 1− x − y Mn x Co y O 2 (NMC) layered compounds are the dominant cathode for lithium ion batteries. The role of crystallographic defects on structure evolution and performance degradation during electrochemical cycling is not yet fully understood. Here, we investigated the structural evolution of a Ni‐rich NMC cathode in a solid‐state cell by in situ transmission electron microscopy. Antiphase boundary (APB) and twin boundary (TB) separating layered phases played an important role on phase change. Upon Li depletion, the APB extended across the layered structure, while Li/transition metal (TM) ion mixing in the layered phases was detected to induce the rock‐salt phase formation along the coherent TB. According to DFT calculations, Li/TM mixing and phase transition were aided by the low diffusion barriers of TM ions at planar defects. This work reveals the dynamical scenario of secondary phase evolution, helping unveil the origin of performance fading in Ni‐rich NMC.

Li, Shuang↗
DOE OSTI2022

Pushing Lithium–Sulfur Batteries towards Practical Working Conditions through a Cathode–Electrolyte Synergy

Abstract The commercialization of lithium–sulfur (Li−S) batteries is still hindered by the unsatisfactory cell performance under practical working conditions, which is mainly caused by the sluggish cathode redox kinetics, severe polysulfide shuttling, and poor Li stripping/plating reversibility. Herein, we report an effective strategy by combining Se‐doped S hosted in an ordered macroporous framework with a highly fluorinated ether (HFE)‐based electrolyte to simultaneously address the aforementioned issues in both cathode and anode. A reversible and stable high areal capacity of >5.4 mAh cm −2 with high Coulombic efficiency >99.2 % can be achieved under high areal Se/S loading (5.8 mg cm −2 ), while the underlying mechanism was further revealed through synchrotron X‐ray probes and Time‐of‐Flight Secondary Ion Mass Spectrometry (ToF‐SIMS). The practical application potential was further evaluated at low (0 °C) and high (55 °C) temperatures under high areal Se/S loading (>5.0 mg cm −2 ) and thin Li metal (40 μm).

Zhao, Chen↗
DOE OSTI2022

Pushing Lithium–Sulfur Batteries towards Practical Working Conditions through a Cathode–Electrolyte Synergy

The commercialization of lithium-sulfur (Li-S) batteries is still hindered by the unsatisfactory cell performance under practical working conditions, which is mainly caused by the sluggish cathode redox kinetics, severe polysulfide shuttling, and poor Li striping/platting reversibility. We reported an effective strategy by combining Se-doped S hosted in an ordered macroporous framework with highly fluorinated ether (HFE)-based electrolyte to simultaneously address the aforementioned issues in both cathode and anode. A reversible and stable high areal capacity of > 5.4 mAh cm -2 with high coulombic efficiency > 99.2% can be achieved under high areal Se/S loading (5.8 mg cm -2 ), while the underlying mechanism was further revealed through synchrotron X-ray probes and Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS). The practical application potential was further evaluated at low (0 °C) and high (55 °C) temperatures under high areal Se/S loading (> 5.0 mg cm -2 ) and thin Li metal (40 µm).

25 ENERGY STORAGE↗
DOE OSTI2023

Regulating Cation Interactions for Zero–Strain and High–Voltage P2–type Na 2/3 Li 1/6 Co 1/6 Mn 2/3 O 2 Layered Oxide Cathodes of Sodium–Ion Batteries

Deep sodium extraction/insertion of sodium cathodes usually causes undesired Jahn–Teller distortion and phase transition, both of which will reduce structural stability and lead to poor long-cycle reliability. Here we report a zero-strain P2- Na 2/3 Li1/6Co 1/6 Mn 2/3 O 2 cathode, in which the lithium/cobalt substitution contributes to reinforcing the host structure by reducing the Mn 3+ /Mn 4+ redox, mitigating the Jahn–Teller distortion, and minimizing the lattice change. 94.5 % of Na + in the unit structure can be reversibly cycled with a charge cut-off voltage of 4.5 V (vs. Na + /Na). Impressively, a solid-solution reaction without phase transitions is realized upon deep sodium (de)intercalation, which poses a minimal volume deviation of 0.53 %. Finally, it attains a high discharge capacity of 178 mAh g –1 , a high energy density of 534 Wh kg –1 , and excellent capacity retention of 95.8 % at 1 C after 250 cycles.

25 ENERGY STORAGE↗
DOE OSTI2026

Surface Vacancy Engineering Re-Routes First-Cycle Redox for Stabilized Li-Rich Layered Cathodes

We demonstrate that atomic-scale surface disorder can control the first-cycle redox sequence of Li-rich layered oxides, eliminating the detrimental process of oxygen release and lattice collapse that degrades performance. In Li1.14Ni0.32Mn0.54O2 (LNMO), a simple chemical treatment introduces oxygen and transition metal (TM) vacancies confined to the particle surface while preserving the bulk layered framework. Multi-modal synchrotron analyses reveal that these vacancies trigger an early oxygen oxidation below 4.4 V, delay nickel oxidation to higher potential, and suppress the formation of covalent Ni4+─O states. This modified pathway prevents irreversible oxygen release, suppresses manganese dissolution, and maintains metal-oxygen coordination at high voltages. Consequently, the treated cathode delivers higher first-cycle Coulombic efficiency (CE), mitigated voltage fade, and superior capacity retention. By directly linking engineered surface disorder to redox reactions and associated structural transformations, this work establishes a general design principle for durable, high-energy-density cathodes.

Kang, Seongkoo↗
DOE OSTI2022

Single‐Crystal LiNi x Mn y Co 1− x − y O 2 Cathodes for Extreme Fast Charging

Abstract Ni‐rich layered LiNi x Mn y Co 1− x − y O 2 (NMCs, x ≥ 0.8) are poised to be the dominating cathode materials for lithium‐ion batteries for the foreseeable future. Conventional polycrystalline NMCs, however, suffer from severe cracking along the grain boundaries of primary particles and capacity loss under high charge and/or discharge rates, hindering their implementation in fast‐charging electric vehicular (EV) batteries. Single‐crystal (SC) NMCs are attractive alternatives as they eliminate intergranular cracking and allow for grain‐level surface optimization for fast Li transport. In the present study, the authors report synthetic approaches to produce SC LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NMC811) samples with different morphologies: Oct‐SC811 with predominating (012)‐family surface and Poly‐SC811 with predominating (104)‐family surface. Poly‐SC811, representing the first experimentally synthesized NMC811 single crystals with (104) surface, delivers superior performance even at the ultra‐high rate of 6 C. Through detailed X‐ray analysis and electron microscopy characterization, it is shown that the enhanced performance originates from better chemical and structural stabilities, faster Li + diffusion kinetics, suppressed side reactions with electrolyte, and excellent cracking resistance. These insights provide important design guidelines in the future development of fast‐charging NMC‐type cathode materials.

Lu, Yanying↗
DOE OSTI2023

Whole-Voltage-Range Solid-Solution Reaction in Layered Oxide Cathode of Sodium-Ion Batteries

Layered manganese-based oxides (LMOs) are promising cathode materials for sodium-ion batteries (SIBs) due to their versatile structures. However, the Jahn–Teller effect of Mn 3+ induces severe distortion of MnO 6 octahedra, and the resultant low symmetry is responsible for the gliding of MnO 2 layers and then inferior multiple-phase transitions upon Na + extraction/insertion. Here, hexagonal P2-Na 0.643 Li 0.078 Mn 0.827 Ti 0.095 O 2 is synthesized through the incorporation of Li and Ti into the distorted orthorhombic P'2-Na 0.67 MnO 2 to function as a phase-transition-free oxide cathode. Further, it is revealed that Li in both the transition-metal and Na layers enhances the covalency of Mn–O bonds and allows degeneracy of Mn 3d e g orbitals to favor the formation of hexagonal phase, and the high strength of Ti–O bonds reduces the electrostatic interaction between Na and O for suppressed Na + /vacancy rearrangements. These collectively lead to a whole-voltage-range solid-solution reaction between 1.8 and 4.3 V with a small volume variation of 1.49%. This rewards its excellent cycling stability (capacity retention of 90% after 500 cycles) and rate capability (89 mAh g -1 at 2000 mA g -1 ).

25 ENERGY STORAGE↗
DOE OSTI2020

Numerical investigation of micro-galvanic corrosion in Mg alloys: Role of the cathodic intermetallic phase size and spatial distributions

Magnesium alloys are of increasing interest in structural applications due to their low-density, moderate specific strength and stiffness, recyclability, and high damping among other properties. However, the wide-scale applicability of magnesium alloys in structural applications has been limited due to many factors including its poor corrosion resistance. In this work, a numerical investigation to simulate the micro-galvanic corrosion behavior was performed to examine the influence of size and distribution of cathodic intermetallic phase (ß-Mg17Al12) in a Mg matrix. The ratio of cathodic to anodic surface area was kept constant in each simulation condition to understand the effect of size and spacing distributions. In general, fragmentation of a larger intermetallic particle into smaller ones was found to enhance the localized current density. However, the uniform distribution of this small intermetallic phase throughout the matrix was found to reduce the overall dissolution current density and hence, pitting corrosion severity.

Beura, Vikrant↗
DOE OSTI2020

A novel battery scheme: Coupling nanostructured phosphorus anodes with lithium sulfide cathodes

Lithium-ion batteries are approaching their theoretical limit and can no longer keep up with the increasing demands of human society. Lithium-sulfur batteries, with a high theoretical specific energy, are promising candidates for next generation energy storage. However, the use of Li metal in Li-S batteries compromises both safety and performance, enabling dendrite formation and causing fast capacity degradation. Previous studies have probed alternative battery systems to replace the metallic Li in Li-S system, such as a Si/Li2S couple, with limited success in performance. Recently, there is a focus on red P as a favorable anode material to host Li. In this work, we establish a novel battery scheme by utilizing a P/C nanocomposite anode and pairing it with a Li 2 S coated carbon nanofiber cathode. We find that red P anode can be compatible in ether-based electrolyte systems and can be successfully coupled to a Li 2 S cathode. Our proof of concept full-cell displays remarkable specific capacity, rate and cycling performances. We expect our work will provide a useful alternative system and valuable insight in the quest for next generation energy storage devices.

25 ENERGY STORAGE↗
DOE OSTI2021

Cathode pre-lithiation/sodiation for next-generation batteries

Electrochemical energy storage is playing a pivotal role in the global pursuit of a clean and sustainable energy future. Lithium-ion batteries (LIBs) are the state-of-the-art technology, but future energy requirements demand higher energy densities and a more diverse battery landscape to meet a wide variety of applications. Unfortunately, many next-generation LIB chemistries and beyond-LIB technologies suffer from large first-cycle irreversible capacity caused by active ion loss. The field of pre-lithiation/sodiation has recently emerged as researchers attempt to mitigate active ion loss and boost the energy density of next-generation LIBs and sodium-ion batteries. Herein, we highlight recent advances in cathode pre-lithiation/sodiation using sacrificial additives and pre-lithiation/sodiation of cathode active materials.

25 ENERGY STORAGE↗
DOE OSTI2020

Unraveling Na and F coupling effects in stabilizing Li, Mn-rich layered oxide cathodes via local ordering modification

Regardless of the prevailing capacity and energy density of lithium, manganese-rich layered oxide (LMR-NMC) cathodes, continuous decay of voltage and overall energy density during cycling hinders this material from commercialization in Li-ion batteries. Although significant work focuses on single doping of Na and F, analysis in portraying the benefit of these ions in diminishing the structural distortion during activation cycle is in doubt. In this study, the effects of co-doping Na and F into the LMR-NMC structure in stabilizing the structure and mitigating oxygen loss during the first cycle are closely examined via in situ x-ray measurements. Na and F co-doping shows a 30% lower degree of Li + /Ni 2+ mixing in the Li layer (C2/m structure), 50% reduced Debye-Waller factor of Mn-O bonding, increase reversible TM migration, and faster Li diffusion relative to the pristine material. Due to the utilization of Ni redox chemistry below 4.4 V, less oxygen redox is required for charge compensation at high voltage. This study offers the first instance to quantitatively evaluate the effects of co-doping Na and F in LMR-NMC cathode in order to minimize voltage degradation by altering the local ordering of O3-type structure, which may rationalize strategies to overcome the issues of the material.

25 ENERGY STORAGE↗
DOE OSTI2026

Ionic Interdiffusion at Cathode|Solid-Electrolyte Interface: A Machine Learning–Assisted Multiscale Investigation and Mitigation Strategies

Future lithium batteries are expected to use solid electrolytes to achieve higher energy density and fast charge capabilities. However, most solid electrolytes are thermodynamically unstable against layered oxide cathodes. In this study, the stability of LiCoO2 (LCO) cathode with Li10GeP2S12 (LGPS) solid electrolyte is investigated using ab initio molecular dynamics (AIMD) and machine learning molecular dynamics (MLMD). The propensity of ionic interdiffusion, formation of a passivating interphase layer, and corresponding decay in cell performance is addressed using a continuum model. Large-scale MLMD simulations confirm that the LCO|LGPS interface permits interdiffusion of cobalt (Co) and other ionic species, leading to the formation and growth of a resistive interphase and to dramatic capacity fade even in the first cycle. We examine the literature evidence that incorporating a thin layer of LiNb0.5Ta0.5O3 (LNTO) between LCO and LGPS prevents the interdiffusion of ions. Atomistic simulations suggest that substituting lithium (Li) in LNTO with Co is thermodynamically unfavorable, thereby inhibiting ionic interdiffusion. The stable Nb5+/Ta5+ states form a rigid metal-oxide framework, which consequently also prevents the substitution of niobium (Nb) or tantalum (Ta). However, continuum-level analysis suggests that the higher mechanical stiffness of LNTO can lead to interfacial delamination between the LCO and LNTO. This phenomenon reduces the effectiveness of the protective layer. This paper, therefore, highlights the need to develop novel interlayers that balance low ionic interdiffusion with low mechanical stiffness.

Ncube, Musawenkosi K.↗
DOE OSTI2022

Multi-scale boron penetration toward stabilizing nickel-rich cathode

Nickel-rich layered oxides LiNi x Co y Mn 1-x-y O 2 (x≥0.8) have been recognized as the preferred cathode materials to develop lithium-ion batteries with high energy density (>300Wh kg -1 ). However, the poor cycling stability and rate capability stemming from intergranular cracks and sluggish kinetics hinder their commercialization. To address such issues, a multi-scale boron penetration strategy is designed and applied on the polycrystalline LiNi 0.83 Co 0.11 Mn 0.06 O 2 particles that are pre-treated with pore construction. The lithium-ion conductive lithium borate in grain gaps functions as the grain binder that can bear the strain/stress from anisotropic contraction/expansion, and provides more pathways for lithium-ion diffusion. As a result, the intergranular cracks are ameliorated and the lithium-ion diffusion kinetics is improved. Moreover, the coating layer separates the sensitive cathode surface and electrolyte, helping to suppress the parasitic reactions and related gas evolution. In addition, the enhanced structural stability is acquired by strong B-O bonds with trace boron doping. As a result, the boron-modified sample with an optimized boron content of 0.5% (B5-NCM) exhibits a higher initial discharge capacity of 205.5mAh g -1 at 0.1C (1C=200mA g -1 ) and improved capacity retention of 81.7% after 100 cycles at 1C. Furthermore, the rate performance is distinctly enhanced by high lithium-ion conductive LBO (175.6mAh g -1 for B5-NCM and 154.6mAh g -1 for B0-NCM at 5C).

25 ENERGY STORAGE↗
DOE OSTI2020

Dendrite-free Al recycling via electrodeposition using ionic liquid electrolytes: The effects of deposition temperature and cathode surface roughness

In this report, the electrodeposition of Al from aluminum scrap alloys (A2020) on copper cathode substrates with varied surface roughness under different deposition temperatures was studied using low-temperature AlCl 3 -1-butyl-3-methyl-imidazolium chloride (BMIC) ionic liquid electrolytes. The bulk electrodeposition of Al was carried out under a voltage of 1.5 V at a stirring rate of 120 rpm using a fixed ionic liquid electrolyte concentration (molar ratio AlCl 3 : BMIC = 2:1). The effects of deposition temperature (range from 80 °C to 140 °C) and surface roughness of Cu cathode substrates (polished by 320, 600, 800, 1200 grits SiC sandpapers and mirror polishing process) on the morphology of deposited Al, current density, current efficiency and energy consumption, were investigated. The Al deposits were characterized using scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), profilometer, and electrochemical measurements for current density, current efficiency, and energy consumption. It is demonstrated that the deposition temperature and surface roughness of Cu electrodes play a critical role in the nucleation and growth of Al deposits. Higher deposition temperature promotes the diffusion and/or migration of Al 2 Cl 7 - ions and then enhances the current density and efficiency during the electrodeposition of Al. Smoother surface of Cu electrodes is preferred for the formation of dendrite-free Al deposits. Typically, on the mirror polished Cu electrode, no Al dendrite structure was observed, and only plate-like Al deposits were formed at the deposition temperature of 100 °C. Pure metallic Al was successfully deposited on Cu electrodes in AlCl 3 + BMIC ionic liquid electrolytes for all experiments with a current efficiency range from 72% to 99% and energy consumption of 4.6–6.3 kW h/kg Al.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

A novel solid oxide electrolytic cell with reduced endothermic load for CO 2 electrolysis using (La 0.80 Sr 0.20 ) 0.95 MnO 3-δ cathode

CO 2 conversion to CO via solid oxide electrolysis provides a potentially efficient method for converting CO 2 into an industrially relevant product. A solid oxide electrolysis cell with (La 0.80 Sr 0.20 ) 0.95 MnO 3-δ (LSM) as the CO 2 reduction cathode, yttrium stabilized zirconia (YSZ) as electrolyte, and nickel as the H 2 oxidation anode was operated 800 °C and 850 °C. Thermogravimetric analysis of the LSM material showed no catalyst oxidation at operating temperatures allowing for CO 2 electrolysis without reducing safe gas. In addition, no cathode material mass gain was observed in the presence of CO suggesting little to no carbon deposition occurred above 750 °C. The formation rates of CO for the cell reached 1.15 mL∙min-1∙ cm -2 for an applied current of 150 mA∙cm -2 achieving a faradaic efficiency of 100 %. Furthermore, the cell displayed good stability in the short-term CO 2 electrolysis test with a nominal voltage drop of 4 mV h -1 for 10 h at 850°C. This study shows the feasibility of operating a solid oxide CO 2 electrolysis cell for CO production with H 2 at the anode to reduce endothermic process load.

(La0.80Sr0.20)0.95MnO3-δ↗
DOE OSTI2025

An epitaxial surface heterostructure anchoring approach for high-performance Ni-rich layered cathodes

Nickel-rich (Ni≥90%) layered oxides materials have emerged as a promising candidate for next-generation high-energy-density lithium-ion batteries (LIBs). However, their widespread application is hindered by structural fatigue and lattice oxygen loss. In this work, an epitaxial surface rock-salt nanolayer is successfully developed on the LiNi 0.9 Co 0.1 O 2 sub-surface via heteroatom anchoring utilizing high-valence element molybdenum modification. This in-situ formed conformal buffer phase with a thickness of 1.2nm effectively suppresses the continuous interphase side-reactions, and thus maintains the excellent structure integrity at high voltage. Furthermore, theoretical calculations indicate that the lattice oxygen reversibility in the anion framework of the optimized sample is obviously enhanced due to the higher content of O 2p states near the Fermi level than that of the pristine one. Meanwhile, the stronger Mo–O bond further reduces cell volume alteration, which improves the bulk structure stability of modified materials. Besides, the detailed charge compensation mechanism suggests that the average oxidation state of Ni is reduced, which induces more active Li + participating in the redox reactions, boosting the cell energy density. As a result, the uniquely designed cathode materials exhibit an extraordinary discharge capacity of 245.4 mAh g −1 at 0.1 C, remarkable rate performance of 169.3 mAh g −1 at 10 C at 4.5V, and a high capacity retention of 70.5% after 1000 cycles in full cells at a high cut-off voltage of 4.4V. Further, this strategy provides an valuable insight into constructing distinctive heterostructure on high-performance Ni-rich layered cathodes for LIBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Optimization of the compositions of polyanionic sodium-ion battery cathode NaFe 2-x V x (PO 4 )(SO 4 ) 2

Sodium (Na) super ionic conductor (NASICON) polyanionic compounds have recently attracted much attention from the battery community because of their electroactive properties and reasonably high ionic conductivities, leading to their use as a cathode in sodium-ion batteries. This article describes the compositional optimizations, crystallographic evaluations, and electrochemical behavior of a new mixed NASICON polyanionic compound, NaFe 2-x V x (PO 4 )(SO 4 ) 2 . By doping the characteristic Fe 3+ sites of the FeO 6 octahedrons with varying amounts of V 3+ , the electrochemical stability and charge transport in NaFe 2 (PO 4 )(SO 4 ) 2 were enhanced. The resulting best composition, with crystal structure NaFe 1.4 V 0.6 (PO 4 )(SO 4 ) 2 resolved through the Rietveld method, exhibited a stable capacity compared with the other synthesized compositions. In situ powder x-ray diffraction measurements, a single-phase intercalation/deintercalation mechanism of the NASICON structure in the measured sodium concentration window was observed with no impurity phase formation. Further electrochemical assessments revealed the interfacial charge transfer kinetics to be the rate-limiting step in the sodium concentration window. Also, the measured sodium-ion diffusivity values in the range of 6 × 10 -11 to 7 × 10 -11 cm 2 /s in the measured sodium concentration range. The results reported here highlight the potential of compositionally and morphologically optimized NaFe 1.4 V 0.6 (PO 4 )(SO 4 ) 2 with higher particle surface areas as a cathode material for high-performance sodium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Enhanced electrolysis performance through hierarchical nanoparticle formation in the BaCo 0.4 Fe 0.4 Zr 0.1 Y 0.1 O 3-δ cathode materials system

This study demonstrated that the activity of a triple conducting BaCo 0.4 Fe 0.4 Zr 0.1 Y 0.1 O 3-δ (BCFZY0.1) air cathode was improved by in situ formation BCFZY0.1 nanoparticles (NPs). The NPs, directly formed from the reaction of BCFZY0.1 with H 2 O and CO 2 from air under electrolysis measurements conditions, were uniformly distributed in a porous BCFZY0.1 framework. At 600 °C, the current density increased and reached a plateau of 1.12 A/cm 2 with the hierarchical BCFZY0.1 cathode under electrolysis conditions within 400 h operation. Distribution of Relaxation Time (DRT) measurements found that the polarization resistance decreased over time as NPs were formed. Furthermore, SEM and TEM results confirm the nanoparticle formation, and the chemical and structural features were assigned to a BCFZY0.1 phase.

08 HYDROGEN↗