Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Space shuttle: Heat transfer investigation of the McDonnell-Douglas delta wing orbiter at a nominal Mach number of 10.5

Heat transfer tests for the delta wing orbiter were conducted in a hypervelocity wind tunnel. A 1.1 percent scale model was tested at a Mach number of approximately 10.5 over an angle of attack range from 10 to 60 degrees over a length Reynolds number range from 5 times 10 to the 6th power to 24 times 10 to the 6th power. Heat transfer results were obtained from model surface heat gage measurements and thermographic phosphor paint. Limited pressure measurements were obtained.

Eaves, R. H.↗
NASA NTRS1975

Results of investigations on a 0.004-scale 140C modified configuration space shuttle vehicle orbiter model (74-0) in the NASA/Langley Research Center hypersonic helium tunnel

Data obtained during a wind tunnel test of a 0.004-scale 140C modified configuration SSV orbiter are documented. The test was conducted during August 1974 with 80 occupancy hours charged, and all runs were conducted at a nominal Mach number of 20 and at Reynolds numbers of 0.7, 1.0, 1.8, and 1,100,000 based on body length. The complete -140C modified model was tested with various elevon settings at angles of attack from 10 to 50 degrees at zero yaw and from angles of sideslip of -10 to +10 at 35 deg angle of attack. The purpose of this test was to obtain high hypersonic longitudinal and lateral-directional stability and control characteristics of the updated SSV configuration.

Hawthorne, P. J.↗
NASA NTRS1975

Design and testing of new center inlet and S-duct for B-727 airplane with refanned JT8D engines

The work described in this paper was part of the NASA refan program. The airflow requirement of the refanned JT8D (-100 series) engine increased about 50% above that of the basic JT8D. This required a redesign of the center inlet and S-duct of the Boeing 727 airplane. The paper describes the design constraints for the S-duct and the analytic method used to define the lines of the new duct. Model tests that were conducted at static, angle-of-attack, and crosswind conditions are described with a variety of flow control devices. Test results showed that the new inlet and S-duct have a pressure recovery comparable to that of the existing inlet. By employing corotating vortex generators, less flow distortion was obtained for the core region than the existing duct has with its counter rotating vortex generators.

Ting, C. T.↗
NASA NTRS1977

Aerodynamic characteristics at Mach 6 of a hypersonic research airplane concept having a 70 deg swept delta wing

The hypersonic aerodynamic characteristics of an air-launched, delta-wing research aircraft concept were investigated at Mach 6. The effect of various components such as nose shape, wing camber, wing location, center vertical tail, wing tip fins, forward delta wing, engine nacelle, and speed brakes was also studied. Tests were conducted with a 0.021 scale model at a Reynolds number, based on model length, of 10.5 million and over an angel of attack range from -4 deg to 20 deg. Results show that most configurations with a center vertical tail have static longitudinal stability at trim, static directional stability at angles of attack up to 12 deg, and static lateral stability throughout the angle of attack range. Configurations with wing tip fins generally have static longitudinal stability at trim, have lateral stability at angles of attack above 8 deg, and are directionally unstable over the angle of attack range.

Clark, L. E.↗
NASA NTRS1978

Space Shuttle Orbiter trimmed center-of-gravity extension study. Volume 4: Effects of configuration modifications on the aerodynamic characteristics of the 139B orbiter at Mach 20.3

Force tests were conducted at Mach 20.3 to determine the effect of several forebody, wing-fillet, and canard modifications on the hypersonic trim capability of a 139B Space Shuttle Orbiter model. Force and moment data were obtained at angles of attack of 10 deg to 54 deg at zero sideslip angle and at a Reynolds number of 1,900,000 based on body length. The results indicated that wing-fillet and canard modifications would increase the allowable forward trimmed center-of-gravity capability by as much as 3.0 percent of the body length.

Scallion, W. I.↗
NASA NTRS1980

Biological and aerodynamic problems with the flight of animals

Biological and aerodynamic considerations related to birds and insects are discussed. A wide field is open for comparative biological, physiological, and aerodynamic investigations. Considerable mathematics related to the flight of animals is presented, including 20 equations. The 15 figures included depict the design of bird and insect wings, diagrams of propulsion efficiency, thrust, lift, and angles of attack and photographs of flapping wing free flying wing only models which were built and flown.

Holst, E. V.↗
NASA NTRS1982

Comparison of analytical and experimental subsonic steady and unsteady pressure distributions for a high-aspect-ratio-supercritical wing model with oscillating control surfaces

The results of a comparative study using the unsteady aerodynamic lifting surface theory, known as the Doublet Lattice method, and experimental subsonic steady- and unsteady-pressure measurements, are presented for a high-aspect-ratio supercritical wing model. Comparisons of pressure distributions due to wing angle of attack and control-surface deflections were made. In general, good correlation existed between experimental and theoretical data over most of the wing planform. The more significant deviations found between experimental and theoretical data were in the vicinity of control surfaces for both static and oscillatory control-surface deflections.

Mccain, W. E.↗
NASA NTRS1982

Adaptive-wall wind-tunnel research at Ames Research Center

Adaptive-wall wind-tunnel research is summarized. This research includes small-scale two- and three-dimensional wind-tunnel experiments and numerical experiments with a three-dimensional adaptive-wall simulator. Airflow through the test-section walls is controlled by adjusting the pressures in segmented plenums. Interference free conditions are successfully attained in subsonic and transonic flows. An adaptive wall test section is constructed for the transonic wind tunnel. Wall interference was reduced in the three dimensional experiment at several angles of attack at Mach 0.60. A wing on wall configuration was modeled in the numerical experiments. These flow simulations showed that free air conditions can be approximated by adjusting boundary conditions at only the floor and ceiling of the test section. No sidewall control was necessary.

Schairer, E. T.↗
NASA NTRS1983

Thrust-induced effects on subsonic longitudinal aerodynamic characteristics of a vectored-engine-over-wing configuration

An investigation was conducted in the Langley 4 by 7 Meter Tunnel of the thrust induced effects on the longitudinal aerodynamic characteristics of a vectored-engine-over-wing fighter aircraft. The investigation was conducted at Mach numbers from 0.14 to 0.17 over an angle-of-attack range from -2 deg to 26 deg. The major model variables were the spanwise blowing nozzle sweep angle and main nozzle vector angle along with trailing edge, flap deflections. The overall thrust coefficient (main and spanwise nozzles) was varied from 0 (jet off) to 2.0. The results indicate that the thrust-induced effects from the main nozzle alone were small and mainly due to boundary-layer control affecting a small area behind the nozzle. When the spanwise blowing nozzles were included, the induced effects were larger than the main nozzle alone and were due to both boundary layer control and induced circulation lift. No leading edge vortex effects were evident.

Quinto, P. F.↗
NASA NTRS1984

Estimated low-speed aerodynamic parameters of an advanced fighter from flight and wind tunnel data

A procedure for determination of aerodynamic model structure and estimation of aerodynamic parameters is applied to data from a modern fighter operating within an angle of attack range of 5 to 60 deg. The paper briefly describes the airplane, flight and wind tunnel data available, postulated models for airplane aerodynamic coefficients and flight data analysis. The results presented contain only a small number of selected longitudinal and lateral parameters. These parameters were obtained from various maneuvers and subsets of joined data from several flights. The estimated parameters are in good agreement with the wind tunnel measurements. The resulting aerodynamic model equations seem to be satisfactory for the prediction of airplane motion.

Klein, V.↗
NASA NTRS1987

Force and moment tests to determine the interaction effects of the reaction control system jet plumes on the space shuttle Orbiter aerodynamics at Mach Number 6 (Test OA352)

The purpose of this test was to expand the existing Space Shuttle aerodynamics and Reaction Control System (RCS) data base to support the Glide Return to Launch Site (GRTLS) abort trajectory and the new Digital Autopilot. An existing model of the orbiter was used to investigate the aerodynamic effects of several combinations of RCS thrusters and thruster momentum ratios at Mach number 6. Two separate model installations were used to achieve an angle-of-attack range of -11 to 46 deg. The test was conducted at a unit Reynolds number of 0.8 x 10 to the 6th per foot.

Cayse, Robert W.↗
NASA NTRS1987

Experimental investigation of the aerodynamic characteristics for a winged-cone concept

Experimental longitudinal and lateral-directional aerodynamics were obtained for a generic aerodynamics were obtaiend for a generic winged-cone configuration having possible application as a transatmospheric vehicle concept. Data were obtained at Mach numbers from 0.6 to 20.0; Reynolds numbers, based on model length, between 2.5 and 5.3 million; and angles of attack from -4 to 20 deg. Results indicate a longitudinal center-of-pressure travel of about 23 percent of the fuselage length for the test Mach number range, with longitudinal instabilities noted at high-supersonic to hypersonic Mach numbers. These instabilities are coupled with directional instability at similar Mach numbers. Predictions with analytic codes, namely, the USAF DATCOM and the tangent-cone option of the Hypersonic Arbitrary Body Program, provided fair agreement with the experimental aerodynamic characteristics at low angles-of-attack.

Phillips, W. Pelham↗
NASA NTRS1988

Navier-Stokes calculations of hovering rotor flowfields

Unsteady, thin-layer Navier-Stokes equations written in rotor coordinates are solved using a partially flux-split, implicit numerical algorithm to calculate the flowfields of a hovering rotor blade at subsonic and transonic conditions. Numerical results are in good agreement with experimental data for both nonlifting and lifting rectangular blades. For the lifting case, the rotor wake effects are modeled by applying a correction to the geometric angle of attack of the blades. Alternate methods of calculating the hovering rotor flowfields in blade-fixed mode that have the same circulation distribution as a hovering blade are explored. All of the results presented in this paper were computed on a Cray-2 supercomputer.

Srinivasan, G. R.↗
NASA NTRS1992

Vortical flow control on a wing-body combination using tangential blowing

The objective of the experimental program reported here was to evaluate the possibility of using tangential blowing to create roll and yaw control on a delta wing-forebody combination at high angles of attack. It is found that the vortical flow over the model can be manipulated more efficiently by blowing on the nose section rather than fuselage. Large rolling moments and side forces are generated by blowing from forebody compared to wing blowing. For a wing-body combination, a model with a blunt nose is found to be less sensitive to flow asymmetry than a sharp-nosed configuration. Rolling moment changes sign from prestall to stall for all the configurations tested.

Celik, Zeki Z.↗
NASA NTRS1993

Robust control of hypersonic vehicles considering propulsive and aeroelastic effects

The influence of propulsion system variations and elastic fuselage behavior on the flight control system of an airbreathing hypersonic vehicle is investigated. Thrust vector magnitude and direction changes due to angle of attack variations affect the pitching moment. Low structural vibration frequencies may occur close to the rigid body modes influencing the angle of attack and lead to possible cross coupling. These effects are modeled as uncertainties in the context of a robust control study of a hypersonic vehicle model accelerating through Mach 8 using H-infinity and mu synthesis techniques. Various levels of uncertainty are introduced into the system. Both individual and simultaneous appearance of uncertainty are considered. The results indicate that the chosen design technique is suitable for this kind of problem provided that a fairly good knowledge of the effects mentioned above is available. The order of the designed controller is reduced but robust performance is lost which shows the need for fixed order design techniques.

Buschek, Harald↗
NASA NTRS1948

The Effect of Boundary-layer Control by Suction and Several High-lift Devices on the Longitudinal Aerodynamic Characteristics of a 47.5 Degree Sweptback Wing-fuselage Combination

An investigation has been made in the Langley full-scale tunnel of a 47.5 degree sweptback wing-fuselage combination equipped for boundary-layer control by suction. The wing aspect ratio was 3.5, the taper ratio was 0.5, and the airfoil sections normal to the quarter-chord line were NACA 64(sub 1)-A112. The wing configurations tested included the wing with various combinations of extensible leading-edge and split flaps. The effect of Reynolds number, suction-slot location and suction flow coefficient on the aerodynamic characteristics was determined for the model at zero yaw over a range of angle of attack.

WING-FUSELAGE COMBINATIONS - AIRPLANES↗
NASA NTRS1937

Calculated and Measured Pressure Distributions over the Midspan Section of the NACA 4412 Airfoil

Pressures were simultaneously measured in the variable-density tunnel at 54 orifices distributed over the midspan section of 5 by 30 inch rectangular model of the NACA 4412 airfoil at 17 angles of attack ranging from -20 degrees to 30 degrees at a Reynolds number of approximately 3,000,000. Accurate data were thus obtained for studying the deviations of the results of potential-flow theory from measured results. The results of the analysis and a discussion of the experimental technique are presented.

Pinkerton, Robert M↗