Characteristics of a new type balance for wind-tunnel models
Internal sting, six component, strain gauge balance to measure aerodynamic forces on wind tunnel test models
STRAIN GAUGE BALANCE↗
SEARCH · Engineering Papers
Results for “aerodynamic modeling”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Aerodynamic Design Study of an Advanced Active Twist Rotor
An Advanced Active Twist Rotor (AATR) is currently being developed by the U.S. Army Vehicle Technology Directorate at NASA Langley Research Center. As a part of this effort, an analytical study was conducted to determine the impact of blade geometry on active-twist performance and, based on those findings, propose a candidate aerodynamic design for the AATR. The process began by creating a baseline design which combined the dynamic design of the original Active Twist Rotor and the aerodynamic design of a high lift rotor concept. The baseline model was used to conduct a series of parametric studies to examine the effect of linear blade twist and blade tip sweep, droop, and taper on active-twist performance. Rotor power requirements and hub vibration were also examined at flight conditions ranging from hover to advance ratio = 0.40. A total of 108 candidate designs were analyzed using the second-generation version of the Comprehensive Analytical Model of Rotorcraft Aerodynamics and Dynamics (CAMRAD II) code. The study concluded that the vibration reduction capabilities of a rotor utilizing controlled, strain-induced twisting are enhanced through the incorporation of blade tip sweep, droop, and taper into the blade design, while they are degraded by increasing the nose-down linear blade twist. Based on the analysis of rotor power, hub vibration, and active-twist response, a candidate aerodynamic design for the AATR consisting of a blade with approximately 10 degrees of linear blade twist and a blade tip design with 30 degree sweep, 10 degree droop, and 2.5:1 taper ratio over the outer five percent of the blade is proposed.
Sekula, Martin K.↗
Evaluation of Preliminary Buffet Forcing Function Development based on Wind-Tunnel Tests of Geometrically-similar Models
The current state-of-the-art for launch vehicle buffet load estimation involves wind tunnel testing of highly instrumented rigid models and data processing of experimental unsteady pressure measurements to estimate the fluctuating aerodynamic loads. The model and instrumentation requirements to accomplish this type of testing are significant. The rigid model, in particular, must be built with relatively high geometric fidelity to approximate similar aerodynamic phenomena that will occur during the full-scale vehicle flight. Due to this requirement, several iterative wind tunnel tests are often required during the design maturation of the vehicle. For preliminary buffet load estimation, however, data from previous launch vehicle wind tunnel tests of geometrically similar models can be used to provide initial buffet environment estimates before a high geometric fidelity wind tunnel test has been conducted. In this paper, two components of this preliminary buffet estimation process are described: (1) assembly of buffet forcing functions from multiple data sources and (2) scaling of these buffet forcing functions to geometrically-similar components of a target vehicle configuration. The impacts of these estimation methods on the full-vehicle buffet forcing functions, including their longitudinal distribution along the vehicle, frequency-content at individual stations, and station-to-station coherence, are investigated. Considerations for using these methods to extrapolate wind tunnel data to geometrically similar models are also discussed.
Patrick S Heaney↗
Estimates for the Aerodynamic Coefficients of Ringsail and Disk-Gap-Band Parachutes Operating on Mars
Models are presented for the aerodynamic coefficients of Supersonic Ringsail and Disk-Gap-Band parachutes as functions of total porosity, Lambda(sub t), Mach number, M, and total angle of attack, Alpha(sub t) (when necessary). The source aerodynamic coefficients data used for creating these models were obtained from a wind tunnel test of subscale parachutes. In this wind tunnel test, subscale parachutes of both parachute types were fabricated from two different fabrics with very different permeabilities. By varying the fabric permeability, while maintaining the parachute geometry constant, it was possible to vary Alpha(sub t). The fabric permeability test data necessary for the calculation of Alpha(sub t) were obtained from samples of the same fabrics used to fabricate the subscale parachutes. Although the models for the aerodynamic coefficients are simple polynomial functions of Alpha(sub t) and M, they are capable of producing good reproductions of the source data. The (Alpha(sub t), M) domains over which these models are applicable are clearly defined. The models are applicable to flight operations on Mars.
Cruz, Juan R.↗
The Effects of a Highly Cambered Low-Drag Wing and of Auxiliary Flaps on the High-Speed Aerodynamic Characteristics of a Twin-Engine Pursuit Airplane Model
Results are presented for tests of two wings, an NACA 230-series wing and a highly-cambered NACA 66-series wing on a twin-engine pursuit airplane. Auxiliary control flaps were tested in combinations with each wing. Data showing comparison of high-speed aerodynamic characteristics of the model when equipped with each wing, the effect of the auxiliary control flaps on aerodynamic characteristics, and elevator effectiveness for the model with the 66-series wing are presented. High-speed aerodynamic characteristics of the model were improved with the 66-series wing.
AIRFOILS - NACA 66,2-416-66,2-616 - CHAR & MOMENTS↗
Aerodynamic Characteristics of Various Configurations of a Model of a 45 Degree Swept-wing Airplane at a Mach Number of 2.01
An investigation has been conducted at the Langley 4- by 4-foot supersonic pressure tunnel at a Mach nmber of 2.01 to determine the aerodynamic characteristics of several configurations of a model of a 45 deg swept-wing airplane. The basic configuratin had a wing with 45 deg sweepback at the quarter-chord line, aspect ration 3.2, taper ration 0.468, NACA 65A005.5 sections just outboard of the inlet and NACA 65A003.7 sections at the tip. The wing was mounted slightly above the body center line and an all-movable horizantal tail was located slightly below the extended chord line of the wing. Tre design incorporated twin wing-root supersonic inlets ducted to a single exit at the base of the fuselage. The configurations investigated included an extended nose length, a bumped-fuselage afterbody, an inlet droop, an lncreased wing aspect ratio, and a revised canopy shape. Configurations employing the wing of increased aspect ratio of 3.7, which constituted the bulk of the tests, produced about a 10-percent increase in lift and in longitudinal stability as compared with the basic wing of aspect ratio 3.2. There was a slight but masurable increase in minimum drag and maximum lift-drag ratio.
Spearman, Leroy M↗
Low speed wind tunnel investigation of a large scale lift fan STOL transport model
The low-speed aerodynamic characteristics of large scale V/STOL transport models with lift fan and lift-cruise fan propulsion systems are discussed. The model of this investigation had two fans mounted side by side in the nose section of the fuselage. This permitted a reasonably deep inlet on the inboard side of each fan while the outboard side had a fairly shallow inlet. Lift-cruise fans were installed on the aft section of the fuselage. Hood-type deflection ducts were used to turn the fan flow from the cruise direction to the lift direction for STOL performance. Fan performance is shown for all four fans both statically and with crossflow. Longitudinal force and moment results are shown for a representative tip speed (forward speed) range through wing supported flight. Lateral-directional characteristics are also presented. The results are presented without analysis.
Atencio, A., Jr.↗
Aerodynamic characteristics of a large-scale semispan model with a swept wing and an augmented jet flap with hypermixing nozzles
The aerodynamic characteristics of the augmentor wing concept with hypermixing primary nozzles were investigated. A large-scale semispan model in the Ames 40- by 80-Foot Wind Tunnel and Static Test Facility was used. The trailing edge, augmentor flap system occupied 65% of the span and consisted of two fixed pivot flaps. The nozzle system consisted of hypermixing, lobe primary nozzles, and BLC slot nozzles at the forward inlet, both sides and ends of the throat, and at the aft flap. The entire wing leading edge was fitted with a 10% chord slat and a blowing slot. Outboard of the flap was a blown aileron. The model was tested statically and at forward speed. Primary parameters and their ranges included angle of attack from -12 to 32 degrees, flap angles of 20, 30, 45, 60 and 70 degrees, and deflection and diffuser area ratios from 1.16 to 2.22. Thrust coefficients ranged from 0 to 2.73, while nozzle pressure ratios varied from 1.0 to 2.34. Reynolds number per foot varied from 0 to 1.4 million. Analysis of the data indicated a maximum static, gross augmentation of 1.53 at a flap angle of 45 degrees. Analysis also indicated that the configuration was an efficient powered lift device and that the net thrust was comparable with augmentor wings of similar static performance. Performance at forward speed was best at a diffuser area ratio of 1.37.
Aiken, T. N.↗
The Aerodynamic Plane Table
This report gives the description and the use of a specially designed aerodynamic plane table. For the accurate and expeditious geometrical measurement of models in an aerodynamic laboratory, and for miscellaneous truing operations, there is frequent need for a specially equipped plan table. For example, one may have to measure truly to 0.001 inch the offsets of an airfoil at many parts of its surface. Or the offsets of a strut, airship hull, or other carefully formed figure may require exact calipering. Again, a complete airplane model may have to be adjusted for correct incidence at all parts of its surfaces or verified in those parts for conformance to specifications. Such work, if but occasional, may be done on a planing or milling machine; but if frequent, justifies the provision of a special table. For this reason it was found desirable in 1918 to make the table described in this report and to equip it with such gauges and measures as the work should require.
Zahm, A F↗
Vertical-Axis Wind Turbine Steady and Unsteady Aerodynamics for Curved Deforming Blades
Vertical-axis wind turbines’ simpler design and low center of gravity make them ideal for floating wind applications. However, efficient design optimization of floating systems requires fast and accurate models. Low-fidelity vertical-axis turbine aerodynamic models, including double multiple streamtube and actuator cylinder theory, were created during the 1980s. Commercial development of vertical-axis turbines all but ceased in the 1990s until around 2010 when interest resurged for floating applications. Despite the age of these models, the original assumptions (2-D, rigid, steady, straight bladed) have not been revisited in full. When the current low-fidelity formulations are applied to modern turbines in the unsteady domain, aerodynamic load errors nearing 50% are found, consistent with prior literature. However, a set of steady and unsteady modifications that remove the majority of error is identified, limiting it near 5%. This paper shows how to reformulate the steady models to allow for unsteady inputs including turbulence, deforming blades, and variable rotational speed. A new unsteady approximation that increases numerical speed by 5–10× is also presented. Combined, these modifications enable full-turbine unsteady simulations with accuracy comparable to higher-fidelity vortex methods, but over 5000× faster.
17 WIND ENERGY↗
Computational Aerodynamic Simulations of a 1215 ft/sec Tip Speed Transonic Fan System Model for Acoustic Methods Assessment and Development
Computational Aerodynamic simulations of a 1215 ft/sec tip speed transonic fan system were performed at five different operating points on the fan operating line, in order to provide detailed internal flow field information for use with fan acoustic prediction methods presently being developed, assessed and validated. The fan system is a sub-scale, low-noise research fan/nacelle model that has undergone extensive experimental testing in the 9- by 15-foot Low Speed Wind Tunnel at the NASA Glenn Research Center. Details of the fan geometry, the computational fluid dynamics methods, the computational grids, and various computational parameters relevant to the numerical simulations are discussed. Flow field results for three of the five operating points simulated are presented in order to provide a representative look at the computed solutions. Each of the five fan aerodynamic simulations involved the entire fan system, which for this model did not include a split flow path with core and bypass ducts. As a result, it was only necessary to adjust fan rotational speed in order to set the fan operating point, leading to operating points that lie on a fan operating line and making mass flow rate a fully dependent parameter. The resulting mass flow rates are in good agreement with measurement values. Computed blade row flow fields at all fan operating points are, in general, aerodynamically healthy. Rotor blade and fan exit guide vane flow characteristics are good, including incidence and deviation angles, chordwise static pressure distributions, blade surface boundary layers, secondary flow structures, and blade wakes. Examination of the flow fields at all operating conditions reveals no excessive boundary layer separations or related secondary-flow problems.
Tweedt, Daniel L.↗
Effect of wing design on the longitudinal aerodynamic characteristics of a wing-body model at subsonic speeds
An investigation has been conducted to determine the effects of wing camber and twist on the longitudinal aerodynamic characteristics of a wingbody configuration. Three wings were used each having the same planform (aspect ratio of 2.5 and leading-edge sweep angle of 44 deg.) but differing in amounts of camber and twist (wing design lift coefficient). The wing design lift coefficients were 0, 0.35, and 0.70. The investigation was conducted over a Mach number range from 0.20 to 0.70 at angles of attack up to about 22 deg. The effect of wing strakes on the aerodynamic characteristics of the cambered wings was also studied. A comparison of the experimentally determined aerodynamic characteristics with theoretical estimates is also included.
Henderson, W. P.↗
Aerodynamic characteristics of a powered, externally blown flap STOL transport model with two engine simulator sizes
The low-speed aerodynamic characteristics are investigated of a general research model - a swept-wing, jet-powered STOL transport with externally blown flaps. The model was tested with four-engine simulators mounted on pylons under the 9.3-percent-thick supercritical airfoil wing. Two sets of air ejectors were used to provide data with large and small engines. Tests were conducted in the Langley V/STOL tunnel over an angle-of-attack range of -4 deg to 22 deg and a thrust-coefficient range from 0 to approximately 4. The effects are described of power, wing leading-edge slat configuration, T-tail and low horizontal-tail positions, and double-slotted flap deflection. Additional untrimmed and trimmed engine-out data and tail-body data are included.
Johnson, W. G., Jr.↗
Supersonic aerodynamic and wake characteristics of large-angle cones at low Reynolds numbers including effects of model support
Large angle cones supersonic aerodynamic and wake characteristics at low Reynolds numbers, including model support interference effects
Brown, C. A., Jr.↗
Active Flutter Suppression Using Reduced-Order Modeling for Transonic Aeroservoelastic Control Law Development
In this paper, several aerodynamic reduced-order models (ROMs) are generated and coupled with structural models to form aeroelastic ROMs. The aerodynamic ROMs generated here include the effects of control surface motion and are appropriate for use in aeroservoelastic applications. Simple observer-based full-state feedback controllers were designed from these aeroelastic ROMs. Additionally, observer gain matrices were designed from and coupled to the aeroelastic ROMs. Each (linear) observer was then used to estimate the dynamics of a (nonlinear) stand-alone computational fluid-structure dynamics simulation. Then, using the estimated states and the full-state feedback controller, control surface commands were fed back into the computational fluid-structure dynamics simulation to successfully achieve active flutter suppression. The process, as well as some results, are presented in this paper.
Waite, Josiah M.↗
Aerodynamic characteristics of a large-scale lift-engine fighter model with external swiveling lift-engines
The aerodynamic characteristics of a six-engine (four lift, two lift-cruise) lift-engine model obtained in the Ames 40- by 80-foot wind tunnel are presented. The model was an approximate one-half scale representation of a lift-engine VTOL fighter aircraft with a variable-sweep wing. The four lift-engines were housed in the aft fuselage with the inlets located above the wing. Longitudinal and lateral-directional force and moment data are presented for a range of exhaust gas momentum ratios (thrust coefficients). Wind tunnel forward speed was varied from 0 to 140 knots corresponding to a maximum Reynolds number of 6.7 million. The data are presented without analysis.
Barrack, J. P.↗
Prediction of XV-15 tilt rotor discrete frequency aeroacoustic noise with WOPWOP
The results, methodology, and conclusions of noise prediction calculations carried out to study several possible discrete frequency harmonic noise mechanisms of the XV-15 Tilt Rotor Aircraft in hover and helicopter mode forward flight are presented. The mechanisms studied were thickness and loading noise. In particular, the loading noise caused by flow separation and the fountain/ground plane effect were predicted with calculations made using WOPWOP, a noise prediction program developed by NASA Langley. The methodology was to model the geometry and aerodynamics of the XV-15 rotor blades in hover and steady level flight and then create corresponding FORTRAN subroutines which were used an input for WOPWOP. The models are described and the simplifying assumptions made in creating them are evaluated, and the results of the computations are presented. The computations lead to the following conclusions: The fountain/ground plane effect is an important source of aerodynamic noise for the XV-15 in hover. Unsteady flow separation from the airfoil passing through the fountain at high angles of attack significantly affects the predicted sound spectra and may be an important noise mechanism for the XV-15 in hover mode. The various models developed did not predict the sound spectra in helicopter forward flight. The experimental spectra indicate the presence of blade vortex interactions which were not modeled in these calculations. A need for further study and development of more accurate aerodynamic models, including unsteady stall in hover and blade vortex interactions in forward flight.
Coffen, Charles D.↗
Wind-tunnel investigation of lateral aerodynamic characteristics of a powered four-duct-propeller VTOL model in transition
Wind tunnel study of lateral and directional aerodynamic characteristics of powered four-duct propeller VTOL scale model in transition
Spreemann, K. P.↗