Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WIND TUNNELS - FIRST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

The NASA-Langley 20-inch supersonic wind tunnel

NASA Langley's new 20-inch supersonic wind tunnel is in the process of reassembly, following extensive modifications. These will result in its incorporation of such features as a 'quiet' flow control valve, thick sintered screens with very large pressure drops, special farings in the contraction section, an instantaneous relief hatch in the test section, and a switching exhaust system that permits flow into a vacuum sphere during startup and shutdown and to the atmosphere during data acquisition. Attention is given to the expected operating map of the new tunnel.

Dillon, J. L.↗
NASA NTRS1988

F-15 SMTD low speed jet effects wind tunnel test results

Key results from low speed wind tunnel testing of the F-15 STOL and Maneuver Technology Demonstrator (SMDT) with thrust reversers are presented. Longitudinally, the largest induced increments in the stability and control occur at landing gear height. These generally reflect an induced lift loss and a nose-up pitching moment, and vary with sideslip. Directional stability is reduced at landing gear height with full reverse thrust. Nonlinearities in the horizontal tail effectiveness are found in free air and at landing gear height.

Blake, William B.↗
NASA NTRS1929

Pressure Distribution on a Slotted R.A.F. 31 Airfoil in the Variable Density Wind Tunnel

Measurements were made in the variable density wind tunnel to determine the pressure distribution over one section of a R.A.F. 31 airfoil with a leading edge slot fully open. To provide data for the study of scale effect on this type of airfoil, the tests were conducted with air densities of approximately one and twenty atmospheres.

Jacobs, Eastman N↗
NASA NTRS1935

Scale Effect on Clark Y Airfoil Characteristics from NACA Full-Scale Wind-Tunnel Tests

This report presents the results of wind tunnel tests conducted to determine the aerodynamic characteristics of the Clark Y airfoil over a large range of Reynolds numbers. Three airfoils of aspect ratio 6 and with 4, 6, and 8 foot chords were tested at velocities between 25 and 118 miles per hour, and the characteristics were obtained for Reynolds numbers (based on the airfoil chord) in the range between 1,000,000 and 9,000,000 at the low angles of attack, and between 1,000,000 and 6,000,000 at maximum lift. With increasing Reynolds number the airfoil characteristics are affected in the following manner: the drag at zero lift decreases, the maximum lift increases, the slope of the lift curve increases, the angle of zero lift occurs at smaller negative angles, and the pitching moment at zero lift does not change appreciably.

Silverstein, Abe↗
NASA NTRS2003

Evaluation and Analysis of F-16XL Wind Tunnel Data from Dynamic Tests

A series of wind tunnel tests were conducted in the NASA Langley Research Center as part of an ongoing effort to develop and test mathematical models for aircraft rigid-body aerodynamics in nonlinear unsteady flight regimes. Analysis of measurement accuracy, especially for nonlinear dynamic systems that may exhibit complicated behaviors, is an essential component of this ongoing effort. In this paper, tools for harmonic analysis of dynamic data and assessing measurement accuracy are presented. A linear aerodynamic model is assumed that is appropriate for conventional forced-oscillation experiments, although more general models can be used with these tools. Application of the tools to experimental data is demonstrated and results indicate the levels of uncertainty in output measurements that can arise from experimental setup, calibration procedures, mechanical limitations, and input errors.

Kim, Sungwan↗
NASA NTRS2007

Fluorescence Visualization of Hypersonic Flow over Rapid Prototype Wind-Tunnel Models

Reentry models for use in hypersonic wind tunnel tests were fabricated using a stereolithography apparatus. These models were produced in one day or less, which is a significant time savings compared to the manufacture of ceramic or metal models. The models were tested in the NASA Langley Research Center 31-Inch Mach 10 Air Tunnel. Most of the models did not survive repeated tests in the tunnel, and several failure modes of the models were identified. Planar laser-induced fluorescence (PLIF) of nitric oxide (NO) was used to visualize the flowfields in the wakes of these models. Pure NO was either seeded through tubes plumbed into the model or via a tube attached to the strut holding the model, which provided localized addition of NO into the model s wake through a porous metal cylinder attached to the end of the tube. Models included several 2-inch diameter Inflatable Reentry Vehicle Experiment (IRVE) models and 5-inch diameter Crew Exploration Vehicle (CEV) models. Various configurations were studied including different sting placements relative to the models, different model orientations and attachment angles, and different NO seeding methods. The angle of attack of the models was also varied and the location of the laser sheet was scanned to provide three-dimensional flowfield information. Virtual Diagnostics Interface technology, developed at NASA Langley, was used to visualize the data sets in post processing. The use of calibration "dotcards" was investigated to correct for camera perspective and lens distortions in the PLIF images. Lessons learned and recommendations for future experiments are discussed.

Alderfer, D. W.↗
NASA NTRS2008

Fluorescence Imaging and Streamline Visualization of Hypersonic Flow over Rapid Prototype Wind-Tunnel Models

Reentry models for use in hypersonic wind tunnel tests were fabricated using a stereolithography apparatus. These models were produced in one day or less, which is a significant time savings compared to the manufacture of ceramic or metal models. The models were tested in the NASA Langley Research Center 31-Inch Mach 10 Air Tunnel. Only a few of the models survived repeated tests in the tunnel, and several failure modes of the models were identified. Planar laser-induced fluorescence (PLIF) of nitric oxide (NO) was used to visualize the flowfields in the wakes of these models. Pure NO was either seeded through tubes plumbed into the model or via a tube attached to the strut holding the model, which provided localized addition of NO into the model s wake through a porous metal cylinder attached to the end of the tube. Models included several 2- inch diameter Inflatable Reentry Vehicle Experiment (IRVE) models and 5-inch diameter Crew Exploration Vehicle (CEV) models. Various model configurations and NO seeding methods were used, including a new streamwise visualization method based on PLIF. Virtual Diagnostics Interface (ViDI) technology, developed at NASA Langley Research Center, was used to visualize the data sets in post processing. The use of calibration "dotcards" was investigated to correct for camera perspective and lens distortions in the PLIF images.

Danehy, Paul M.↗
NASA NTRS2012

Wind-Tunnel Balance Characterization for Hypersonic Research Applications

Wind-tunnel research was recently conducted at the NASA Langley Research Center s 31-Inch Mach 10 Hypersonic Facility in support of the Mars Science Laboratory s aerodynamic program. Researchers were interested in understanding the interaction between the freestream flow and the reaction control system onboard the entry vehicle. A five-component balance, designed for hypersonic testing with pressurized flow-through capability, was used. In addition to the aerodynamic forces, the balance was exposed to both thermal gradients and varying internal cavity pressures. Historically, the effect of these environmental conditions on the response of the balance have not been fully characterized due to the limitations in the calibration facilities. Through statistical design of experiments, thermal and pressure effects were strategically and efficiently integrated into the calibration of the balance. As a result of this new approach, researchers were able to use the balance continuously throughout the wide range of temperatures and pressures and obtain real-time results. Although this work focused on a specific application, the methodology shown can be applied more generally to any force measurement system calibration.

Lynn, Keith C.↗
NASA NTRS2018

Acoustic Methods Used in the NASA Glenn 9- by 15- Foot Low-Speed Wind Tunnel

The 9- by 15-Foot Low Speed Wind Tunnel has been used for acoustic testing for more than 40 years. The facility is principally used for testing aircraft engine propulsion components, for both aerodynamic performance and acoustics. The present report discusses the instrumentation and procedures currently used for the acquisition of high-quality acoustic data from aircraft engine fan models.

Noise↗
NASA NTRSDate not supplied

Rapid Aero Modeling for Urban Air Mobility Aircraft in Wind-Tunnel Tests

Rapid Aero Modeling (RAM) applied to wind tunnel testing, RAM-T, is an approach to efficiently and automatically obtain aerodynamic models during testing. The approach saves time and resources by responding to the demand for experimental efficiency and model fidelity. Motivation for this demand is more acute when investigating a class of vehicles categorized as Urban Air Mobility (UAM) aircraft where many features from both aircraft and rotorcraft are present. RAM-T provides a feedback loop around the test facility to guide the test toward high-fidelity, statistically rigorous aircraft models. The general RAM approach is applicable to computational or physical experiments. It combines concepts from design of experiment theory and aircraft system identification theory that allow the user the freedom to choose, in advance of the test, a specific level of fidelity in terms of prediction error. RAM only collects data required to meet the user-specified fidelity and fidelity is only limited by the facility and test article capabilities. This paper presents results from tests conducted for development of an automated RAM-T technology. The results highlight some of the unique features of RAM applied to eVTOL configurations.

Aerodynamics↗
NASA NTRS1992

A comparison of experimental data with CFD for the NSWC Hypervelocity Wind Tunnel No. 9 Mach 14 Nozzle

An experimental and numerical study has been performed of the flow physics occurring in the Naval Surface Warfare Center Hypervelocity Wind Tunnel No.9 Mach 14 Nozzle. Mach 8, 10, 14, and 18 test section conditions are obtained utilizing various axisymmetric contoured wind tunnel nozzles. Numerical and experimental results are presented for the Mach 14 configuration.

Korte, John J.↗
NASA NTRS1998

Wind Tunnel Magnetic Suspension and Balance Systems With Transversely Magnetized Model Cores

This paper discusses the possibility of using vertically magnetized model cores for wind tunnel Magnetic Suspension and Balance Systems (MSBS) in an effort to resolve the traditional "roll control" problem. A theoretical framework is laid out, based on previous work related to generic technology development efforts at NASA Langley Research Center. The impact of the new roll control scheme on traditional wind tunnel MSBS configurations is addressed, and the possibility of demonstrating the new scheme with an existing electromagnet assembly is explored. The specific system considered is the ex- Massachusetts Institute of Technology (MIT), ex-NASA, 6-inch MSBS currently in the process of recommissioning at Old Dominion University. This system has a sufficiently versatile electromagnet configuration such that straightforward "conversion" to vertically magnetized cores appears possible.

Britcher, Colin P.↗
NASA NTRS1923

Wind Tunnel of Zeppelin Airship Company

This report discusses the general considerations for the design of aerodynamic laboratories. The dimensions, construction, and components of the wind tunnel are given special attention.

WIND TUNNELS - GERMANY - ZEPPELIN AIRSHIP COMPANY↗
NASA NTRS1986

Predicting Wall Modifications for Adaptive Wind Tunnels

Wall shape changed iteratively until it matches streamlines. FLEXWAL predicts upper and lower wall modifications necessary to remove wall-interference effects in adaptive-wall wind tunnels. FLEXWAL aids in elimination of wall-interference effects on objects tested in typical two-dimensional wind tunnel with rigid sidewalls and flexible, solid floor and ceiling boundaries. Iterative procedure valid for subsonic and transonic test conditions, and convergence of method verified both analytically and experimentally. FLEXWAL written in FORTRAN IV for batch execution.

Everhart, J. L.↗
NASA NTRS1938

Wind-Tunnel Investigation of Air Inlet and Outlet Openings for Aircraft, Special Report

An investigation was made in the NACA 5-foot vertical wind tunnel of a large variety of duct inlets and outlets to obtain information relative to their design for the cooling or the ventilation systems on aircraft. Most of the tests were of openings in a flat plate but, in order to determine the best locations and the effects of interference, a few tests were made of openings in an airfoil. The best inlet location for a system not including a blower was found to be at the forward stagnation point; for one including a blower, the best location was found to be in the region of lowest total head, probably in the boundary layer near the trailing edge. Design recommendations are given, and it is shown that correct design demands a knowledge of the external flow and of the internal requirements in addition to that obtained from the results of the wind tunnel tests.

Rogallo, Francis M.↗
NASA NTRS1971

Preliminary wind-tunnel investigation of the effects of engine nacelles on a transport configuration with high lift drag ratios to a Mach number of 1.00

Wind tunnel tests to determine the effect of engine nacelles added to a low wing fuselage vertical tail configuration utilizing the NASA supercritical airfoil and a refined area ruled fuselage are discussed. The engine arrangement consisted of two aft fuselage, side mounted flow through nacelles and a solid body of revolution mounted above the fuselage in a manner similar to the Boeing 727. A preliminary analysis of the wind tunnel data shows that favorable interference drag can be obtained with the proper longitudinal locations of the nacelles, by canting the nacelle inlets, and by cusping the rearward region of the nacelle.

Flechner, S. G.↗
NASA NTRS1992

Aerodynamic design of axisymmetric hypersonic wind-tunnel nozzles using least-squares/parabolized Navier-Stokes procedure

A new procedure unifying the best of present classical design practices, CFD and optimization procedures, is demonstrated for designing the aerodynamic lines of hypersonic wind tunnel nozzles. This procedure can be employed to design hypersonic wind tunnel nozzles with thick boundary layers where the classical design procedure has been demonstrated to break down. Advantages of this procedure allow full utilization of powerful CFD codes in the design process, solves an optimization problem to determine the new contour, may be used to design new nozzles or improve sections of existing nozzles, and automatically compensates the nozzle contour for viscous effects as part of the unified design procedure.

Korte, John J.↗