Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transient Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Simulation studies of multiple large wind turbine generators on a utility network

The potential electrical problems that may be inherent in the inertia of clusters of wind turbine generators and an electric utility network were investigated. Preliminary and limited results of an analog simulation of two MOD-2 wind generators tied to an infinite bus indicate little interaction between the generators and between the generators and the bus. The system demonstrated transient stability for the conditions considered.

Gilbert, L. J.↗

Flight evaluation of a hydromechanical backup control for the digital electronic engine control system in an F100 engine

The backup control (BUC) features, the operation of the BUC system, the BUC control logic, and the BUC flight test results are described. The flight test results include: (1) transfers to the BUC at military and maximum power settings; (2) a military power acceleration showing comparisons bvetween flight and simulation for BUC and primary modes; (3) steady-state idle power showing idle compressor speeds at different flight conditions; and (4) idle-to-military power BUC transients showing where cpmpressor stalls occurred for different ramp rates and idle speeds. All the BUC transfers which occur during the DEEC flight program are initiated by the pilot. Automatic transfers to the BUC do not occur.

Walsh, K. R.↗

Computer simulation of thermal modeling of primary lithium cells

The objective was to gain a better understanding of the safety problem of primary Li-SOCl2 and Li-SO2 cells by carrying out detailed thermal modeling work. In particular, the transient heat generation rates during moderate and extermely high discharge rate tests of Li-SOCl2 cells were predicted and compared with those from the electrochemical heating. The difference between the two may be attributed to the lithium corrosion and other chemical reactions. The present program was also tested for charging of Li-SO2. In addition, the present methodology should be applicable to other primary cylindrical cells as well as rechargeable battery analyses with minor modifications.

Young, I. Cho↗

Constraints on galactic distributions of gamma-ray burst sources from BATSE observations

The paradigm that gamma-ray bursts originate from Galactic sources is studied in detail using the angular and intensity distributions observed by the Burst and Transient Source Experiment (BATSE) on NASA's Compton Gamma Ray Observatory (CGRO). Monte Carlo models of gamma-ray burst spatial distributions and luminosity functions are used to simulate bursts, which are then folded through mathematical models of BATSE selection effects. The observed and computed angular intensity distributions are analyzed using modifications of standard statistical homogeneity and isotropy studies. Analysis of the BATSE angular and intensity distributions greatly constrains the origins and luminosities of burst sources. In particular, it appears that no single population of sources confined to a Galactic disk, halo, or localized spiral arm satisfactorily explains BATSE observations and that effects of the burst luminosity function are secondary when considering such models. One family of models that still satisfies BATSE observations comprises sources located in an extended spherical Galactic corona. Coronal models are limited to small ranges of burst luminosity and core radius, and the allowed parameter space for such models shrinks with each new burst BATSE observes. Multiple-population models of bursts are found to work only if (1) the primary population accounts for the general isotropy and inhomogeneity seen in the BATSE observations and (2) secondary populations either have characteristics similar to the primary population or contain numbers that are small relative to the primary population.

Hakkila, Jon↗

Algorithm For Computation Of Chemically Reacting Flow

Efficient algorithm developed for use in solving differential equations of transient, chemically reacting flows at all speeds from zero to high mach numbers. Mathematical models represent coupling of thermal, chemical, and dynamical effects. Original intended application is numerical simulation of flows in rocket engines; also applicable to other complex flows affected by finite-rate chemistry - for example, flows in turbines and in internal-combustion engines.

Chen, Yen-Sen↗

Proof of Concept Testing for Integrated Reaction Control System

Integrated Reaction Control Systems (IRCS) are considered an enabling technology for future human exploration of the solar system. An IRCS uses the same fuel and oxidizer as the main propulsion system, allowing for increased performance and simplified cryogenic fluid management operations. The IRCS team at Marshall Spaceflight Center is currently evaluating an IRCS system that uses a combination of electric pumps and pressure-regulation devices to provide a constant flow of conditioned propellant to a thruster bank during operation. In the spring 2021 test series presented here, the feasibility of this concept was evaluated using liquid nitrogen as a simulant for liquid oxygen. The goal of this test series was to demonstrate the ability of the pump and pressure regulator to maintain adequate thruster inlet conditions during transient operation.

Cameron Hines↗

Direct simulation for the instability and breakup of laminar liquid jets

A direct numerical simulation method is described for predicting the deformation of laminar liquid jets. In the present nonlinear direct simulation, the convective term, which has been discarded in past linear analyses by Rayleigh and others, is included in the hydrodynamic equations. It is shown that only by maintaining full complexity of the nonlinear surface tension term accurate drop formation can be predicted. The continuity and momentum equations in the transient form are integrated on an adaptive grid, conforming the jet and surface wave shape. The equations, which are parabolic in time and elliptic in space, are solved by a TVD scheme with characteristic flux splitting. The results of the present work are discussed and compared with available measurements and other analyses. The comparison shows that among the predictions, the current 1-D direct simulation results agree best with the experimental data. Furthermore, the computer time requirements are much (an order of magnitude) smaller than those of previously reported multidimensional analyses.

Chuech, S. G.↗

Large Eddy/Reynolds-Averaged Navier-Stokes Simulations of CUBRC Base Heating Experiments

ven with great advances in computational techniques and computing power during recent decades, the modeling of unsteady separated flows, such as those encountered in the wake of a re-entry vehicle, continues to be one of the most challenging problems in CFD. Of most interest to the aerothermodynamics community is accurately predicting transient heating loads on the base of a blunt body, which would result in reduced uncertainties and safety margins when designing a re-entry vehicle. However, the prediction of heat transfer can vary widely depending on the turbulence model employed. Therefore, selecting a turbulence model which realistically captures as much of the flow physics as possible will result in improved results. Reynolds Averaged Navier Stokes (RANS) models have become increasingly popular due to their good performance with attached flows, and the relatively quick turnaround time to obtain results. However, RANS methods cannot accurately simulate unsteady separated wake flows, and running direct numerical simulation (DNS) on such complex flows is currently too computationally expensive. Large Eddy Simulation (LES) techniques allow for the computation of the large eddies, which contain most of the Reynolds stress, while modeling the smaller (subgrid) eddies. This results in models which are more computationally expensive than RANS methods, but not as prohibitive as DNS. By complimenting an LES approach with a RANS model, a hybrid LES/RANS method resolves the larger turbulent scales away from surfaces with LES, and switches to a RANS model inside boundary layers. As pointed out by Bertin et al., this type of hybrid approach has shown a lot of promise for predicting turbulent flows, but work is needed to verify that these models work well in hypersonic flows. The very limited amounts of flight and experimental data available presents an additional challenge for researchers. Recently, a joint study by NASA and CUBRC has focused on collecting heat transfer data on the backshell of a scaled model of the Orion Multi-Purpose Crew Vehicle (MPCV). Heat augmentation effects due to the presence of cavities and RCS jet firings were also investigated. The high quality data produced by this effort presents a new set of data which can be used to assess the performance of CFD methods. In this work, a hybrid LES/RANS model developed at North Carolina State University (NCSU) is used to simulate several runs from these experiments, and evaluate the performance of high fidelity methods as compared to more typical RANS models. .

Salazar, Giovanni↗

Transient desorption of water vapor - A potential source of error in upper atmosphere rocket experiments

Results of measurements of the outgassing rates of samples of materials and surface finishes used on the outer skins of rocket-borne experiment packages in simulated rocket ascents. The results showed outgassing rates for anodized aluminum in the second minute of flight which are two to three orders of magnitude higher than those given in typical tables of outgassing rates. The measured rates for aluminum with chromate conversion surface coatings were also abnormally high. These abnormally high initial rates fell quickly after about five to ten minutes to values comparable with those in the published literature. It is concluded that anodized and chromate conversion coatings on the aluminum outer surfaces of a sounding rocket experiment package will cause gross distortion of the true water vapor environment.

Kendall, B. R. F.↗

Improved Coupled Fluid/Structural Dynamical Model

Improved algorithm developed for simulation of coupled motions of fluids and structures. Minimum requirement for correct simulation of damping is forces and velocities at interface compatible in models of structure and fluid at each time step. Improved algorithm, conforms to this requirement, involves fluid-transient model, structural modal/transient model, and an algebraic impedance/coupling subalgorithm. Use of this algorithm greatly improves computational stability.

Fenwick, James R.↗

Reexamination of METMAN, Recommendations on Enhancement of LCVG, and Development of New Concepts for EMU Heat Sink

METMAN is a 41-node transient metabolic computer code developed in 1970 and revised in 1989 by Lockheed Engineering and Sciences, Inc. This program relies on a mathematical model to predict the transient temperature distribution in a body influenced by metabolic heat generation and thermal interaction with the environment. A more complex 315-node model is also available that not only simulates the thermal response of a body exposed to a warm environment, but is also capable of describing the thermal response resulting from exposure to a cold environment. It is important to compare the two models for the prediction of the body's thermal response to metabolic heat generation and exposure to various environmental conditions. Discrepancies between the twi models may warrant an investigation of METMAN to ensure its validity for describing the body's thermal response in space environment. The Liquid Cooling and Ventilation Garment is a subsystem of the Extravehicular Mobility Unit (EMU). This garment, worn under the pressure suit, contains the liquid cooling tubing and gas ventilation manifolds; its purpose is to alleviate or reduce thermal stress resulting from metabolic heat generation. There is renewed interest in modifying this garment through identification of the locus of maximum heat transfer at body-liquid cooled tubing interface. The sublimator is a vital component of the Primary Life Support System (PLSS) in the EMU. It acts as a heat sink to remove heat and humidity from the gas ventilating circuit and the liquid cooling loop of the LCVG. The deficiency of the sublimator is that the ice, used as the heat sink, sublimates into space. There is an effort to minimize water losses in the feedwater circuit of the EMU. This requires developing new concepts to design an alternative heat sink system. Efforts are directed to review and verify the heat transfer formulation of the analytical model employed by METMAN. A conceptual investigation of regenerative non-venting heat-sink subsystem for the EMU is recommended.

Karimi, Amir↗

Modeling of Multi-Tube Pulse Detonation Engine Operation

The present paper explores some preliminary issues concerning the operational characteristics of multiple-tube pulsed detonation engines (PDEs). The study is based on a two-dimensional analysis of the first-pulse operation of two detonation tubes exhausting through a common nozzle. Computations are first performed to assess isolated tube behavior followed by results for multi-tube flow phenomena. The computations are based on an eight-species, finite-rate transient flow-field model. The results serve as an important precursor to understanding appropriate propellant fill procedures and shock wave propagation in multi-tube, multi-dimensional simulations. Differences in behavior between single and multi-tube PDE models are discussed, The influence of multi-tube geometry and the preferred times for injecting the fresh propellant mixture during multi-tube PDE operation are studied.

Ebrahimi, Houshang B.↗

Primate translational vestibuloocular reflexes. III. Effects of bilateral labyrinthine electrical stimulation

The effects of functional, reversible ablation and potential recruitment of the most irregular otolith afferents on the dynamics and sensitivity of the translational vestibuloocular reflexes (trVORs) were investigated in rhesus monkeys trained to fixate near and far targets. Translational motion stimuli consisted of either steady-state lateral and fore-aft sinusoidal oscillations or short-lasting transient lateral head displacements. Short-duration (usually <2 s) anodal (inhibitory) and cathodal (excitatory) currents (50-100 microA) were delivered bilaterally during motion. In the presence of anodal labyrinthine stimulation, trVOR sensitivity and its dependence on viewing distance were significantly decreased. In addition, anodal currents significantly increased phase lags. During transient motion, anodal stimulation resulted in significantly lower initial eye acceleration and more sluggish responses. Cathodal currents tended to have opposite effects. The main characteristics of these results were simulated by a simple model where both regularly and irregularly discharging afferents contribute to the trVORs. Anodal labyrinthine currents also were found to decrease eye velocity during long-duration, constant velocity rotations, although results were generally more variable compared with those during translational motion.

NASA Program Biomedical Research and Countermeasur↗

Intelligent Engine Systems: Adaptive Control

We have studied the application of the baseline Model Predictive Control (MPC) algorithm to the control of main fuel flow rate (WF36), variable bleed valve (AE24) and variable stator vane (STP25) control of a simulated high-bypass turbofan engine. Using reference trajectories for thrust and turbine inlet temperature (T41) generated by a simulated new engine, we have examined MPC for tracking these two reference outputs while controlling a deteriorated engine. We have examined the results of MPC control for six different transients: two idle-to-takeoff transients at sea level static (SLS) conditions, one takeoff-to-idle transient at SLS, a Bode power command and reverse Bode power command at 20,000 ft/Mach 0.5, and a reverse Bode transient at 35,000 ft/Mach 0.84. For all cases, our primary focus was on the computational effort required by MPC for varying MPC update rates, control horizons, and prediction horizons. We have also considered the effects of these MPC parameters on the performance of the control, with special emphasis on the thrust tracking error, the peak T41, and the sizes of violations of the constraints on the problem, primarily the booster stall margin limit, which for most cases is the lone constraint that is violated with any frequency.

Gibson, Nathan↗

Gene Expression and Structural Skeletal Responses to Long-Duration Simulated Microgravity in Rats

Spaceflight has deleterious effects on skeletal structure and function, specifically causingprofound loss in bone mass, density, and strength, as well as changes in expression levels of genes related to oxidative stress [Hyeon et al., Smith et al.]. It is known that bone resorption remains elevated after spaceflight and that bone density and strength fail to recover completely even years following spaceflight [Smith et al., Carpenter et al.]. However, our current understanding of the signaling pathways and molecular mechanisms that control bone loss and that link oxidative stress, bone resorption, and mechanical unloading of skeletal tissue is incomplete. Here, we aim to examine skeletal responses to simulated long-duration spaceflight on bone loss using the ground-based hindlimb unloading (HU) model in adult (9 months old) male rats. We hypothesized that simulated microgravity leads to the temporal regulation of oxidative-defense genes and pro-osteoclastogenic factors, showing progression and eventual plateau during long-term unloading, and that transient changes at early timepoints in these pathways precede skeletal adaptations to long-duration unloading. We will identify oxidativestress and bone resorption-related changes using global gene expression analysis (Affymetrix arrays) for both acute (within 14 days) and long-term timepoints (90 days). We will also use quantitative PCR to examine changes in expression of genes related to oxidative metabolism (e.g. Nrf2, SOD-1), bone turnover (resorption and formation markers, e.g. TRAP, osteocalcin respectively, SOST), and osteoclastogenesis (e.g. RANKL, OPG) at both early and late timepoints. We will then use detailed microarchitectural and structural analysis through microcomputed tomography to relate gene expression changes with structural changes in bone, expecting that plateaus in gene expression correlate with long-term changes in bone microarchitecture.

Rael, Victoria E.↗

Extratropical Large-Scale Traveling Weather Systems in the Southern Hemisphere on Mars

From late-autumn through early-spring, the middle- and high-latitudes of both hemispheres of Mars and its predominantly carbon-dioxide atmosphere support mean equator-to-pole thermal contrasts, and then, support a strong mean westerly polar vortex. Observations from orbiting spacecraft indicate that this intense mean baroclinicity-barotropicity supports large-scale eastward traveling weather systems (i.e., transient, traveling synoptic-period waves, on the order of the Rossby deformation scale). On Earth, extratropical weather disturbances arise from wind-shear instabilities, and these are critical components of the terrestrial global circulation. So it is the case for Mars. Large-scale traveling weather systems on Mars serve as agents in the transport of heat, momentum and scalar and tracer quantities (e.g., atmospheric dust, watervapor, ice clouds, chemical species, etc). Such weather systems interact with other large-scale atmospheric circulation components, namely, quasi-stationary (i.e., forced Rossby) modes; global thermal tidal modes; and then, upon large-/continental- geographical scales, upslope/ down-slope flows amongst high relief, low relief, impact basins, and volcanic rises, and more. The character of Mars' traveling extratropical weather disturbances in its southern hemisphere during late winter through early spring is investigated using a high-resolution Mars global climate model (i.e., Mars GCM), and one from the Agency's Mars Climate Modeling Center (MCMC) based at the NASA Ames Research Center. The climate model includes several complex atmospheric physical packages. With such physics modules, our global climate simulations present comparatively well with observations of the planet's current water cycle (Haberle et al.,2019). The climate model is "forced" with an annual dust cycle (i.e., nudged based on MGS/TES observations). Compared to the northern-hemisphere counterparts, the southern synoptic-period weather disturbances and accompanying frontal waves have smaller meridional and zonal scales, and are less intense. Influences of the zonally asymmetric (i.e., east-west varying) topography on southern large-scale weather are investigated, in addition to large-scale up-slope/down-slope flows and the diurnal cycle. A southern storm zone in late winter and early spring presents in the western hemisphere via orographic influences from the Tharsis highlands, and the Argyre and Hellas impact basins. Geographically localized transient-wave activity diagnostics are constructed that illuminate dynamical differences amongst the simulations and these are presented.

Hollingsworth, Jeffery L.↗

Hybrid-Vlasov Simulation of Soft X-Ray Emissions at the Earth’S Dayside Magnetospheric Boundaries

Solar wind charge exchange produces emissions in the soft X-ray energy range which can enable the study of near-Earth space regions such as the magnetopause, the magnetosheath and the polar cusps by remote sensing techniques. The Solar wind–Magnetosphere–Ionosphere Link Explorer (SMILE) and Lunar Environment heliospheric X-ray Imager (LEXI) missions aim to obtain soft X-ray images of near-Earth space thanks to their Soft X-ray Imager (SXI) instruments. While earlier modeling works have already simulated soft X-ray images as might be obtained by SMILE SXI during its mission, the numerical models used so far are all based on the magnetohydrodynamics description of the space plasma. To investigate the possible signatures of ion-kinetic-scale processes in soft X-ray images, we use for the first time a global hybrid-Vlasov simulation of the geospace from the Vlasiator model. The simulation is driven by fast and tenuous solar wind conditions and purely southward interplanetary magnetic field. We first produce global X-ray images of the dayside near-Earth space by placing a virtual imaging satellite at two different locations, providing meridional and equatorial views. We then analyze regional features present in the images and show that they correspond to signatures in soft X-ray emissions of mirror mode wave structures in the magnetosheath and flux transfer events (FTEs) at the magnetopause. Our results suggest that, although the time scales associated with the motion of those transient phenomena will likely be significantly smaller than the integration time of the SMILE and LEXI imagers, mirror-mode structures and FTEs can cumulatively produce detectable signatures in the soft X-ray images. For instance, a local increase by 30% in the proton density at the dayside magnetopause resulting from the transit of multiple FTEs leads to a 12% enhancement in the line-of-sight- and time integrated soft X-ray emissivity originating from this region. Likewise, a proton density increase by 14% in the magnetosheath associated with mirror-mode structures can result in an enhancement in the soft X-ray signal by 4%. These are likely conservative estimates, given that the solar wind conditions used in the Vlasiator run can be expected to generate weaker soft X-ray emissions than the more common denser solar wind. These results will contribute to the preparatory work for the SMILE and LEXI missions by providing the community with quantitative estimates of the effects of small-scale, transient phenomena occurring on the dayside.

magnetosphere↗

Investigation of the Effectiveness of Dynamic Seat in a Black Hawk Flight Simulation

Low cost alternatives have been sought to provide motion cues in ground-based flight simulators to meet mission objectives. The ability to provide high frequency vibrations makes the dynamic seat attractive to helicopter training applications. Previous studies have found that dynamic seat does enhance the realism of the cockpit and affect pilots' workload. This investigation, conducted under the auspices of the Joint Shipboard Helicopter Integration Process (JSHIP), is using a three degree-of-freedom dynamic seat, i.e., heave, surge, and sway, with limited travels in a research simulator configured as a UH-60 Black Hawk at NASA Ames Research Center. The seat's effectiveness is studied using hover, landing, pirouette, bob-up/bob-down, sidestep, and acceleration/deceleration maneuvers. Seat commands consist of constant vibrations in heave and sway which provide the fundamental vibratory cues. Pilot station accelerations and collective controls provide onset and sustained commands. In addition, transient effects due to translational-lift, collective; and normal acceleration are produced by regulating the magnitude and frequency that depend on the rotor rpm. Results are compared to flight test data and two other ground-based motion systems configurations, i.e., a motion condition with very large motion travels and a motion condition that is comparable with commercial simulator travels. Both subjective and objective data will be analyzed to determine the significance of the motion cueing effect in each system for selected maneuvers.

Chung, William W. Y.↗