Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TiN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Experimental investigation of the effects of gravity on thermosolutal convection and compositional homogeneity in Bridgman grown, compound semiconductors

Lead-tin-telluride has been grown in a thermally stable mode (solutally unstable) and in a solutally stable (thermally unstable) mode in a Bridgman configuration. Significant differences in the crystal morphology and the compositional homogeneity have been found between the two configurations. In addition, for the solutally stable configuration, evidence has been found that the flow characteristics in the melt change drastically during the course of the run.

Crouch, R. K.↗
NASA NTRS1984

The mechanisms of formation and prevention of channel segregation during alloy solidification

Using a base chilled configuration, conditions for the formation and prevention of segregation channels are studied in the ammonium chloride-water and lead-tin systems. Such channels develop when the rejected solute is less dense than the solvent and are therefore a result of density inversion, but slow (less than 5 rpm) rates of mold rotation, about axes inclined to the vertical by 20 to 30 deg, throughout the time of solidification, effectively prevent the formation or propagation of these channels. In experiments with artificially created or blocked channels, a simultaneous solute plume in the bulk liquid must be present in order for a channel to develop. The results indicate that channels originate not within the dendritic array, but immediately ahead of the growth front as a result of perturbation from the less dense boundary layer into the bulk liquid. The effect of mold movement is to translate laterally the bulk liquid relative to the growth front so that perturbations are sheared off. The nature of the liquid movement is considered and shown to be a function of the mold dimensions.

Hellawell, A.↗
NASA NTRS1984

Thermocapillary-driven convection in supported and floating-zone crystallization

Marangoni flow was induced in a thin disk of molten tin with an atomically clean surface by heating it from below in an ultra high vacuum apparatus. The radial distribution of temperature was measured and no temperature oscillations were observed. Strong mechanical disturbances introduced at a Marangoni number of about 4300 died out quickly with time indicating that the system was stable. Mathematical models indicate that strong flows in a two cell structure exist under the conditions studied, and that the velocity profile in the cell near the surface is of the boundary layer type which varies rapidly with depth.

Gill, W. N.↗
NASA NTRS1985

Moessbauer studies on LaNi(4.7)Sn(0.3) and its hydride

Moessbauer measurements were made on LaNi(4.7)Sn(0.3) at room and liquid nitrogen temperatures. Experimental data yielded a singlet at room temperature and a doublet at liquid-nitrogen temperature. Spectra of the hydrided sample yielded a doublet at liquid-nitrogen temperature with an increase in the quadrupole splitting compared to the unhydrided spectra, but no change in the isomer shift. These data indicate that there is no significant interaction between the tin and the hydrogen. The magnetic character remained the same down to liquid-nitrogen temperature as evidenced by the Moessbauer data. X-ray diffraction measurements on the hydride showed an expanded lattice with the same structure as found for the unhydrided sample. A decrease in particle size was observed upon hydriding.

Oliver, F. W.↗
NASA NTRS1986

Filters for Submillimeter Electromagnetic Waves

New manufacturing process produces filters strong, yet have small, precise dimensions and smooth surface finish essential for dichroic filtering at submillimeter wavelengths. Many filters, each one essentially wafer containing fine metal grid made at same time. Stacked square wires plated, fused, and etched to form arrays of holes. Grid of nickel and tin held in brass ring. Wall thickness, thickness of filter (hole depth) and lateral hole dimensions all depend upon operating frequency and filter characteristics.

Berdahl, C. M.↗
NASA NTRS1985

Crystal Growth Research in Space

The objectives of this work are to develop growth techniques and theory leading to improved bulk growth of semiconductor single crystals. Ground based experiments will be complemented by experiments carried out in the low-g environment provided by the space shuttle. Analytical studies and laboratory investigations are being conducted to better define the causes of crystalline defects and inhomogeneities. The compound semiconductor lead-tin-telluride is being used as the modeling material. Theoretical techniques are being developed to predict the thermal and solutal fields which are present during bulk growth from a melt. Techniques for measuring the thermophysical properties of semiconductors at high temperatures have been developed. During the past year electrochemical etching techniques have been developed for delineation of inhomogeneous regions in crystals. Thermal diffusivity measurements have been completed for the solid and liquid phases of PbTe and PbSnTe. Preliminary results have been obtained on the effects on crystal morphology of gravity, interface shape and interaction between the melt and the container.

Crouch, R. K.↗
NASA NTRS1985

Float Zone Experiments in Space

The objective of this work has been to evaluate whether or not Marangoni flow could be suppressed in molten metals by the presence of very thin oxide films. Experimental work has been carried out on molten Sn under UHV conditions. A disk floating zone arrangement was developed to allow in situ Auger examination of molten surfaces. An electron energy loss technique was developed which allows detection of continuous tin oxide films of 6 A or greater. Experiments were planned to detect the effects of oxide formation upon Marangoni flow by measuring: (1) temperature profiles, (2) solid liquid interface shapes, (3) macrosegregation, and (4) the onset of oscillatory Marangoni flow by detecting oscillating temperature variations. Work on (4) showed that oscillatory temperature variations of frequency or = 10 Hz were not present in the disk float zone geometry under conditions of Ma = 4300 with an oxide free molten surface. The disk float zone geometry was modeled with a finite element analysis and temperature and velocity profiles were determined.

Verhoeven, J. D.↗
NASA NTRS1985

Glass breaking strength: The role of surface flaws and treatments

Although the intrinsic strength of silicon dioxide glass is of the order of 10 to the 6th power lb/sq in, the practical strength is roughly two orders of magnitude below this theoretical limit, and depends almost entirely on the surface condition of the glass, that is, the number and size of flaws and the residual surface compression (temper) in the glass. Glass parts always fail in tension when these flaws grow under sustained loading to some critical size. Research associated with glass encapsulated crystalline-Si photovoltaic (PV) modules has greatly expanded our knowledge of glass breaking strength and developed sizeable data base for commercially available glass types. A detailed design algorithm is developed for thickness sizing of rectangular glass plates subject to pressure loads. Additional studies examine the strength of glass under impact loading conditions such as that caused by hail. Although the fundamentals of glass breakage are directly applicable to thin film modules, the fracture strength of typical numerical glass must be replaced with data that reflect the high temperature tin oxide processing, laser scribing, and edge processing peculiar to thin film modules. The fundamentals of glass breakage applicable to thin film modules and preliminary fracture strength data for a variety of 1 ft square glass specimens representing preprocessed and post processed sheets from current amorphous-Si module manufacturers are presented.

Moore, D.↗
NASA NTRS1986

Method of making macrocrystalline or single crystal semiconductor material

A macrocrystalline or single crystal semiconductive material is formed from a primary substrate including a single crystal or several very large crystals of a relatively low melting material. This primary substrate is deposited on a base such as steel or ceramic, and it may be formed from such metals as zinc, cadmium, germanium, aluminum, tin, lead, copper, brass, magnesium silicide, or magnesium stannide. These materials generally have a melting point below about 1000 C and form on the base crystals the size of fingernails or greater. The primary substrate has an epitaxial relationship with a subsequently applied layer of material, and because of this epitaxial relationship, the material deposited on the primary substrate will have essentially the same crystal size as the crystals in the primary substrate. If required, successive layers are formed, each of a material which has an epitaxial relationship with the previously deposited layer, until a layer is formed which has an epitaxial relationship with the semiconductive material. This layer is referred to as the epitaxial substrate, and its crystals serve as sites for the growth of large crystals of semiconductive material. The primary substrate is passivated to remove or otherwise convert it into a stable or nonreactive state prior to deposition of the seconductive material.

Shlichta, P. J.↗
NASA NTRS1986

Development status of first Tethered Satellite System

An MOU between NASA and Italian research organizations has assigned the responsibilities for the development, payload integration, launch and operation of a Tethered Satellite System (TSS). The TSS will include a deployer mounted on a Spacelab pallet, science equipment on a customized mission support structure and a satellite connected to the Orbiter by a tether. The satellite is 1.6 m in diameter and can weight up to 500 kg. The deployer will be insulated from the Orbiter because of the conductive nature of the tether. The first mission is to demonstrate the TSS technology, perform electrodynamic investigations of the interaction of the tether with ambient space plasma, and gather data on atmospheric interactions in the lower thermosphere, geomagnetic phenomena and gravimetric characteristics. The first TSS will be deployed 20 km outward from the Orbiter and the earth on a strand of tin-coated copper wire wrapped in Teflon insulation, braided Kevlar and a Nomek jacket. The first strand is designed to accommodate 53 N tension. The satellite on the end of the tether will be a multimission platform for facile changeout of the scientific package from mission-to-mission.

Sisson, J. M.↗
NASA NTRS1986

Practical method for highly accurate large-scale surface calculations

An accurate and efficient film linearized muffin-tin orbital (FLMTO) technique for surface electronic-structure calculations is presented which uses only 60-70 basis functions, as opposed to the 300 functions used in the linear augmented plane-wave method. Calculations for three different (3d and 4d) transition-metal films resulted in high quality results for five-layer slabs of Cu(001), Fe(001), and Ru(001), in addition to good results for the work functions and projected density of states. By retaining the LMTO small basis size, computer time and memory are reduced, making practical the study of systems with a larger number of atoms in the two-dimensional unit cell.

Fernando, G. W.↗
NASA NTRS1987

Pretreatment of Platinum/Tin Oxide-Catalyst

Addition of CO to He pretreatment doubles catalytic activity. In sealed, high-energy, pulsed CO2 laser, CO and O2 form as decomposition products of CO2 in laser discharge zone. Products must be recombined, because oxygen concentration of more than few tenths of percent causes rapid deterioration of power, ending in unstable operation. Promising low-temperature catalyst for combining CO and O2 is platinum on tin oxide. New development increases activity of catalyst so less needed for recombination process.

Hess, Robert V.↗
NASA NTRS1987

The alloy undercooling experiment on the Columbia STA 61-C space shuttle mission

An Alloy Undercooling experiment was performed in an electromagnetic levitator during the Columbia STS 61-C mission in January 1986. One eutectic nickel-tin alloy specimen was partially processed before an equipment failure terminated the experiment. Examination of the specimen showed evidence of undercooling and some unusual microstructural features.

Harf, Fredric H.↗
NASA NTRS1987

Catalysts for long-life closed-cycle CO2 lasers

Long-life, closed-cycle operation of pulsed CO2 lasers requires catalytic CO-O2 recombination both to remove O2, which is formed by discharge-induced CO2 decomposition, and to regenerate CO2. Platinum metal on a tin (IV) oxide substrate (Pt/SnO2) has been found to be an effective catalyst for such recombination in the desired temperature range of 25 to 100 C. This paper presents a description of ongoing research at NASA-LaRC on Pt/SnO2 catalyzed CO-O2 recombination. Included are studies with rare-isotope gases since rare-isotope CO2 is desirable as a laser gas for enhanced atmospheric transmission. Results presented include: (1) achievement of 98% to 100% conversion of a stoichiometric mixture of CO and O2 to CO2 for 318 hours (greater than 1 x 10 to the 6th power seconds), continuous, at a catalyst temperature of 60 C, and (2) development of a technique verified in a 30-hour test, to prevent isotopic scrambling when CO-18 and O-18(2) are reacted in the presence of a common-isotope Pt/Sn O-16(2) catalyst.

Schryer, David R.↗
NASA NTRS1986

Gravitational macrosegregation in binary Pb-Sn alloy ingots

A space shuttle experiment employing the General Purpose (Rocket) Furnace (GPF) in its isothermal mode of operation is manifested on MSL-3, circa 1989. The central aim of this experiment is to investigate the effect of reduced gravity levels on the segregation behavior in a slowly, and isothermally, cooled sample of a binary Pb-15 wt% Sn alloy. This experiment should be able to simulate, in a small laboratory sample, some aspects of the segragation phenomena occurring in large industrial ingots. Ground-based experiments conducted in the single-cavity simulator of the GPF, in support of the microgravity experiment are described in detail. The results of the MSFC experiments are compared with other related experiments conducted at Case Western Reserve University (CWRS), wherein the isothermal constraints were relaxed. The isothermally processed samples indicate a small and gradual increase in fraction eutectic, and a corresponding increase in tin content, from the bottom to the top of the ingot. The radial variations are minimal near the ingot bottom, but there are large radial variations in the top half. In the CWRU experiments, more severe segregations, including segregation defects known as freckles. Follow up experiments employing the GPF without the isothermal constraints, or other suitably modified space shuttle hardware are suggested.

Laxmanan, V.↗
NASA NTRS1987

Production of pulsed atomic oxygen beams via laser vaporization methods

Energetic pulsed atomic oxygen beams were generated by laser-driven evaporation of cryogenically frozen ozone/oxygen films and thin films of indium-tin oxide (ITO). Mass and energy characterization of beams from the ozone/oxygen films were carried out by mass spectrometry. The peak flux, found to occur at 10 eV, is estimated from this data to be 3 x 10(20) m(-2) s(-1). Analysis of the time-of-flight data indicates a number of processes contribute to the formation of the atomic oxygen beam. The absence of metastable states such as the 2p(3) 3s(1) (5S) level of atomic oxygen blown off from ITO films is supported by the failure to observe emission at 777.3 nm from the 2p(3) 3p(1) (5P sub J) levels. Reactive scattering experiments with polymer film targets for atomic oxygen bombardment are planned using a universal crossed molecular beam apparatus.

Brinza, David E.↗
NASA NTRS1987

Status of indium phosphide solar cell development at Spire

On-going development of indium phosphide solar cells for space applications is presented. The development is being carried out with a view towards both high conversion efficiency and simplicity of manufacture. The cell designs comprise the ion-implanted cell, the indium tin oxide top contact cell, and the epitaxial cell grown by metal organic chemical vapor deposition. Modelling data on the limit to the efficiency are presented and comparison is made to measured performance data.

Spitzer, M. B.↗
NASA NTRS1987

ITO/InP solar cells: A comparison of devices fabricated by ion beam and RF sputtering of the ITO

This work was performed with the view of elucidating the behavior of indium tin oxide/indium phosphide (ITO/InP) solar cells prepared by RF and ion beam sputtering. It was found that using RF sputter deposition of the ITO always leads to more efficient devices than ion beam sputter deposition. An important aspect of the former technique is the exposure of the single crystal p-InP substrates to a very low plasma power prior to deposition. Substrates treated in this manner have also been used for ion beam deposition of ITO. In this case the cells behave very similarly to the RF deposited cells, thus suggesting that the lower power plasma exposure (LPPE) is the crucial process step.

Coutts, T. J.↗