Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Stabilization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
NASA NTRS1963

Wind-tunnel Measurement of Propeller Whirl-flutter Speeds and Static-stability Derivatives and Comparison with Theory

Results of an experimental investigation of propeller whirl flutter are presented for a model consisting of an isolated, rigid system of propeller and simulated power plant mounted with flexibility in pitch and yaw on a rigid sting. A range of propeller blade angles, restraint stiffnesses, and restraint damping coefficients was investigated for a system symmetrical i n pitch and yaw with a windmilling propeller. Measurements of the static-stability derivatives were also made by using a simple balance and were compared with two sets of theoretical derivatives. Whirl-flutter calculations were made with the theoretical and measured derivatives. Some limited results were obtained for the whirl flutter of the model mounted on a cantilever semispan wing. The measured whirl-flutter speeds and frequencies of the isolated model were in very good agreement with those predicted by calculations in which measured derivatives and viscous damping were used. This agreement was better than that obtained by using structural damping. Predicted whirl-flutter speeds for the isolated model were lower when theoretical stability derivatives were used than when measured derivatives were used. The theoretical and experimental static-stability derivatives exhibited the same trends, but in certain instances differed appreciably in magnitude. the measured whirl-flutter boundary for the one configuration considered.

PROPELLER↗
NASA NTRS1952

Investigation of the Influence of Fuselage and Tail Surfaces on Low-speed Static Stability and Rolling Characteristics of a Swept-wing Model

Results are presented of a wind-tunnel investigation to determine influence of the fuselage and tail on static stability and rotary derivatives in roll of a model having 45 degrees sweptback wing and tail surfaces. The wing alone and the model without the horizontal tail showed marginal longitudinal stability near maximum lift. The longitudinal stability of the complete model was satisfactory. The vertical tail produced larger increments of rate of change of lateral-force and yawing-moment coefficients with wing-tip helix angle than the fuselage or the horizontal tail.

TAIL-WING-FUSELAGE COMBINATIONS - AIRPLANES↗
NASA NTRS1942

Stability of elastically supported columns

A criterion is developed for the stiffness required of elastic lateral supports at the ends of a compression member to provide stability. A method based on this criterion is then developed for checking the stability of a continuous beam-column. A related method is also developed for checking the stability of a member of a pin-jointed truss against rotation in the plane of the truss.

COMPRESSION MEMBERS-STABILITY↗
NASA NTRS1946

Comparison of Wind-Tunnel and Flight Measurements of Stability and Control Characteristics of a Douglas A-26 Airplane

Tests in Langley pressure tunnel of model XA-26 bomber were compared with those of A-26B (twin-engine attack bomber) and showed that static longitudinal stability, indicated by elevator-fixed neutral points, and variation of elevator deflection in straight and turning flight were good. Airplane possessed improved stability at low speeds which was attributed to pronounced stalling at root of production wing. At rudder-force reversal at speeds higher than those in flight tests, agreement in rudder-fixed and rudder-free static directional stability was good. Hinge moment obtained at zero sideslip was satisfactory for determining aileron forces in sideslip.

SIDESLIPPING - DOUGLAS A-26↗
DOE OSTI2021

Impact of Increased Inverter Penetration on Power System Small-Signal Stability: Preprint

The transformation of the power system to include more distributed energy resources (DER) implies an increase in the number of inverter-based resources deployed on the grid. Envisioning future scenarios, this paper presents a small-signal stability analysis for a power grid comprising synchronous generators and inverter-based resources. Three types of inverter control are considered: grid following, droop-controlled grid forming, and virtual oscillator control grid forming. Although small-signal stability of power systems is a widely studied topic, systematic analysis of mixed machine-inverter systems with detailed control models at various inverter penetration levels are limited. This paper addresses the gap with numerical simulations tailored to the IEEE 39-bus system. Results show the system may become unstable at high inverter penetration level of grid-following inverters, and grid-forming inverter control can potentially improve system stability, thereby enabling very high level of DERs.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2021

In-situ Investigations on Gold Nanoparticles Stabilization Mechanisms in Biological Environments Containing HSA

Nanoparticles (NPs) developments advance innovative biomedical applications. However, complex interactions and the low colloidal stability of NPs in biological media restrict their widespread utilization. The influence of NPs properties on the colloidal stability for gold NPs with 5 and 40 nm in diameter with two surface modifications, methoxy-polyethylene glycol-sulfhydryl (PEG) and citrate, in NaCl and human serum albumin (HSA) protein solution, is investigated. This study is based on small-angle X-ray scattering (SAXS) methods allowing the in-situ monitoring of interactions in physiological conditions. The PEG coating provides high colloidal stability for NPs of both sizes. For 5 nm NPs in NaCl solution, a stable 3D self-assembled body-centered cubic (BCC) arrangement is detected with an interparticle distance of 20.7 ± 0.1 nm. In protein solution, this distance increases to 21.9 ± 0.1 nm by protein penetration inside the ordered structure. For citrate-capped NPs, a different mechanism is observed. The protein particles attach to the NPs surfaces, and an appropriate concentration of proteins results in a stable suspension. Cryogenic transmission electron microscopy (Cryo-TEM), UV–visible spectroscopy, and dynamic light scattering (DLS) support the SAXS results. The findings will pave the way to design and synthesize NPs with controlled behaviors in biomedical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Additive‐Free Oxidized Spiro‐MeOTAD Hole Transport Layer Significantly Improves Thermal Solar Cell Stability

Perovskite solar cells are among the most promising new solar technologies, already surpassing polycrystalline silicon solar cell efficiencies. The stability of the highest efficiency devices at elevated temperature is, however, poor. These cells typically use Spiro-MeOTAD as the hole transporting layer. It is generally believed that additives, required for enhancing electrical conductivity and optimizing energy level alignment, are responsible for the reduced stability—inferring that Spiro-MeOTAD based hole transporting layers are intrinsically unstable. Here, a reliable noble metal free synthesis of Spiro-MeOTAD (bis(trifluoromethane)sulfonimide) 4 is presented which is used as the oxidizing agent. No additives are added to the partially oxidized Spiro-MeOTAD hole-transporting layer. Device efficiencies up to 24.2% are achieved. Electrical conductivity is largely developed by the first 1% oxidation. Further oxidation shifts the energy levels away from the vacuum level, which allows tuning of the energy level alignment without the use of additives—contradicting the current understanding of this system. Without additives, devices demonstrate significant improvement in stability at elevated temperatures up to 85 °C under one sun over 1400 h continuous illumination. The remaining degradation is pinpointed to ion migration and reactions in the perovskite layer which may be further suppressed with compositional engineering and adequate ion barrier layers.

14 SOLAR ENERGY↗
DOE OSTI2024

Theoretical Investigation of the Adsorbate and Potential–Induced Stability of Cu Facets During Electrochemical CO 2 and CO Reduction

The activity and product selectivity of electrocatalysts for reactions like the carbon dioxide reduction reaction (CO 2 RR) are intimately dependent on the catalyst's structure and composition. While engineering catalytic surfaces can improve performance, discovering the key sets of rational design principles remains challenging due to limitations in modeling catalyst stability under operating conditions. Herein, we perform first-principles density functional calculations adopting implicit solvation methods with potential control to study the influence of adsorbates and applied potential on the stability of different facets of model Cu electrocatalysts. Using coverage dependencies extracted from microkinetic models, we describe an approach for calculating potential and adsorbate-dependent contributions to surface energies under reaction conditions, where Wulff constructions are used to understand the morphological evolution of Cu electrocatalysts under CO 2 RR conditions. Here we identify that CO*, a key reaction intermediate, exhibits higher kinetically and thermodynamically accessible coverages on (100) relative to (111) facets, which can translate into an increased relative stabilization of the (100) facet during CO 2 RR. Our results support the known tendency for increased (111) faceting of Cu nanoparticles under more reducing conditions and that the relative increase in (100) faceting observed under CO 2 RR conditions is likely attributed to differences in CO* coverage between these facets.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

High‐Throughput Study of Amorphous Stability and Optical Properties of Superlattice‐Like Ge–Sb–Te Thin Films

A high‐throughput ion beam sputtering system is used to synthesize compositional gradient superlattice‐like (SLL) thin film libraries of Ge–Sb–Te alloys over the entire phase diagram. Here, the optical properties and structural evolution of the Ge–Sb–Te combinatorial SLL thin film are investigated. A systematic screening over the annealing temperature, annealing time, and modulation period has elucidated the critical factors that affect the stability of the metastable phase and optical properties. It is found that amorphous stability and optical constant are highly dependent on the modulation period and chemical composition of the thin film. This data‐driven approach offers new perspectives for accelerating the development of new materials with excellent optical and amorphous stability and for exploring their mechanisms, by greatly expanding the dataset of Ge–Sb–Te alloys with SLL structures through high‐throughput experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Free-Surface Liquid Lithium Flow Modeling and Stability Analysis for Fusion Applications

Liquid metal plasma facing components are considered an attractive design choice for fusion devices including pilot plants. Virtual prototyping of such devices includes modeling of free-surface flow of the electrically conductive liquid, which requires computational fluid dynamics (CFD) and magnetohydrodynamics (MHD) simulations. Numerical tools capable of simulating flows and heat transfer in the free-surface MHD flow were developed at PPPL based on the customized ANSYS CFX. Here, MHD is introduced using a magnetic vector potential approach. Free-surface flow capabilities are available in the code and were tested. Special stabilization procedures were derived and applied to improve convergence of the momentum equations with the source terms due to the Lorentz force and surface tension. Important characteristics of the fusion-relevant liquid metal flow is free surface smoothness and stability. Heat flux from the plasma impacts the liquid surface at a very acute angle, so any change of the free surface from axisymmetry can dramatically increase the local heat flux density and thus create excessive evaporation of liquid lithium into the plasma, which is detrimental to operations. Stability analysis of the liquid metal film flow was performed to determine applicable flow regimes. Thin film flow along horizontal wall is considered. Effects of gravity, magnetic field, and surface tension are included in the analysis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Effect of tension during sulfonation stabilization for UHMWPE-derived carbon fibers

Polyethylene is a promising low-cost alternative precursor material for carbon fiber production, but it has yet to show mechanical properties near or surpassing polyacrylonitrile-derived carbon fibers. The high molecular weight and order of ultra-high molecular weight polyethylene (UHMWPE) may offer a pathway to realizing this promise by enabling long-range graphitic structure formation and superior mechanical properties. The tension applied during the precursor stabilization process is crucial to maintaining the shape of the fibers during the conversion process, but no published study has yet probed the relationship between sulfonation tension and carbon fiber microstructure and mechanical properties. In this work, a logarithmic sweep of tensile stress was applied to UHMWPE fibers during the stabilization process followed by carbonization. Increasing tension significantly reduced fiber shrinkage, resulted in straighter fibers with less severe kink bands, and greatly improved the mechanical properties of the fibers. Raman spectroscopy and X-ray diffraction revealed that in all cases the carbon fibers were largely amorphous, but increasing tension resulted in increased size and alignment of the turbostratic crystallites with the fiber axis. Large voids were present in the sample fibers, so the Griffith-Irwin relation was employed to predict the potential ultimate tensile strength of the fibers with voids reduced to sizes comparable to commercially produced fibers. Furthermore, this work demonstrates the importance of tension applied during the stabilization of polyethylene fibers for carbon fiber production and establishes a framework for achieving high mechanical properties from these precursors.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Subfield crop yields and temporal stability in thousands of US Midwest fields

Understanding subfield crop yields and temporal stability is critical to better manage crops. Several algorithms have proposed to study within-field temporal variability but they were mostly limited to few fields. In this study, a large dataset composed of 5520 yield maps from 768 fields provided by farmers was used to investigate the influence of subfield yield distribution skewness on temporal variability. The data are used to test two intuitive algorithms for mapping stability: one based on standard deviation and the second based on pixel ranking and percentiles. The analysis of yield monitor data indicates that yield distribution is asymmetric, and it tends to be negatively skewed (p < 0.05) for all of the four crops analyzed, meaning that low yielding areas are lower in frequency but cover a larger range of low values. The mean yield difference between the pixels classified as high-and-stable and the pixels classified as low-and-stable was 1.04 Mg ha –1 for maize, 0.39 Mg ha –1 for cotton, 0.34 Mg ha –1 for soybean, and 0.59 Mg ha —1 for wheat. The yield of the unstable zones was similar to the pixels classified as low-and-stable by the standard deviation algorithm, whereas the two-way outlier algorithm did not exhibit this bias. Furthermore, the increase in the number years of yield maps available induced a modest but significant increase in the certainty of stability classifications, and the proportion of unstable pixels increased with the precipitation heterogeneity between the years comprising the yield maps.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Water-Dispersible CsPbBr 3 Perovskite Nanocrystals with Ultra-Stability and its Application in Electrochemical CO 2 Reduction

Thanks to the excellent optoelectronic properties, lead halide perovskites (LHPs) have been widely employed in high-performance optoelectronic devices such as solar cells and light-emitting diodes. However, overcoming their poor stability against water has been one of the biggest challenges for most applications. Herein, we report a novel hot-injection method in a Pb-poor environment combined with a well-designed purification process to synthesize water-dispersible CsPbBr 3 nanocrystals (NCs). The as-prepared NCs sustain their superior photoluminescence (91% quantum yield in water) for more than 200 days in an aqueous environment, which is attributed to a passivation effect induced by excess CsBr salts. Thanks to the ultra-stability of these LHP NCs, for the first time, we report a new application of LHP NCs, in which they are applied to electrocatalysis of CO 2 reduction reaction. Noticeably, they show significant electrocatalytic activity (faradaic yield: 32% for CH 4 , 40% for CO) and operation stability (> 350 h).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Structural damage and phase stability of Al 0.3 CoCrFeNi high entropy alloy under high temperature ion irradiation

In this study, an initially single phase high entropy alloy (HEA) Al 0.3 CoCrFeNi was irradiated by 3 MeV Au ions to a fluence of 6 × 10 15 cm –2 (~31 dpa at damage peak) at four different temperatures ranging from 250 °C to 650 °C. Transmission electron microscopy (TEM) and Atom probe tomography (APT) were employed to study the evolution of structural damage and phase stability with irradiation temperature. Al 0.3 CoCrFeNi exhibited a similar evolution of irradiation-induced defects with temperature as compared with conventional FCC alloys. At 250 °C and 350 °C, most of the visible irradiation-induced defects were faulted 1/3$\langle{111}\rangle$ dislocation loops. As the irradiation temperature increased to 500 °C, perfect 1/2$\langle{110}\rangle$ dislocation loops were observed along with the faulted loops. At the highest irradiation temperature 650 °C, only dislocation lines and networks could be observed. Regarding phase stability, the 3 MeV Au irradiation was observed to suppress the precipitation of (Ni, Al)-enriched nano clusters and the L12 ordered structure at irradiation temperatures 250 °C to 500 °C whereas precipitation of the B2 ordered structure was accelerated at 650 °C. This resulted in qualitatively opposite precipitation behavior between the ion irradiated damage region and unirradiated region at 500 °C and 650 °C. The opposite phase stability of the ion-irradiated damage region and unirradiated region at different temperatures is attributed to the competing effects of ballistic dissolution vs irradiation enhanced diffusion on precipitation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coupled solute effects enable anomalous high-temperature strength and stability in nanotwinned Al alloys

Nanoprecipitates or grain refinement can effectively enhance the mechanical strength of Al alloys, but the room-temperature strengths of precipitation hardened and nanocrystalline Al alloys often fall below 1 GPa. Furthermore, they are largely plagued by precipitous mechanical softening at elevated temperature below 300°C, mostly due to degraded microstructural stability. Here, we report a mechanism of coupled solute effect in nanotwinned Al-Fe-Ti alloys that enables stability of nanograins up to 400°C and an unprecedented high-temperature flow stress of ~ 1.7 GPa at 300°C. The supersaturated Fe solutes in Al act as effective grain refiner, forming superstrong solid solution alloys. More importantly, empirical evidence combined with first principle calculations indicate that the Ti solutes delay the agglomeration of Fe solutes, thereby remarkably extending the temperature window for the stability of nanograins in nanotwinned Al alloys. Finally, this study highlights the opportunity to design ultrastrong and stable nanostructured alloys for potential high temperature applications via a coupled solute effect.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Linking thermoset ink rheology to the stability of 3D-printed structures

Thermoset polymer composites show promise for additive manufacturing (AM) applications to address some of the limitations of the more widely used thermoplastic feedstock materials. Thermosets offer attractive mechanical properties while providing excellent interlayer bonding, high thermal and chemical stability, and reduced energy consumption as a result of deposition at room temperature. However, since thermoset resins rely on a crosslinking reaction to solidify, rather than quickly cooling like thermoplastics, viscoelastic properties must be relied upon to maintain deposited shape after deposition until crosslinking can occur. This fact has not impeded development and characterization of new thermoset feedstocks on the small scale, but recent efforts to increase scale of thermoset printing have highlighted issues with structural stability under self-weight. This study addresses issues of self-weight by investigating the mechanisms that cause collapse of tall, thin printed walls. Using nanoclay- and fumed silica-filled epoxy feedstocks, this work compares the collapse height for printed walls to stability models based on yielding and buckling mechanics. Inputs for these models – shear yield stress and storage modulus – were taken directly from parallel plate rheometry measurements. Model predictions were found to be in good agreement with experimental results, where both yielding and buckling behavior were observed, provided the rheological properties after a shear excursion were used as inputs. This work establishes a direct link between basic rheological properties of the feedstock, geometry of the printed object, and achievable height. Overall, the results presented highlight the importance of understanding recovery behavior in thermoset feedstocks and provide valuable guidance on the development of more effective direct-ink writing feedstock materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Atomic-scale modeling of C/N kinetic stability descriptors for PGM-free electrocatalysts at finite temperatures

The durability of platinum group metal-free (PGM-free) electrocatalysts is a major barrier to their usage in polymer electrolyte fuel cell cathodes. C and N removal from active sites may play an important role in the catalyst’s ability to maintain high activity. While C degradation mechanisms are kinetically controlled, previous studies have focused on thermodynamic descriptors. In this work, we develop a temperature-dependent kinetic descriptor of C and N stability using an electron beam-damage model. Our approach considers the electron beam energy threshold (EBET) describing the knock-on displacement of C and N atoms as a stability descriptor for atomic structures. The stability of different sites is calculated to be different showing this approach can discriminate between similar sites with varied configurations. Additionally, we provide important insight regarding TEM beam damage of proposed active sites. We calculate 60 keV electrons can damage some proposed active site structures even at room temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Hybrid data-driven cement-stabilized soil design: An integration of machine learning, multi-objective optimization, and life cycle assessment

Soil stabilization is crucial in geotechnical engineering, yet conventional methods are often time-consuming, resource-intensive, and environmentally unsustainable. Despite growing interest in Machine Learning (ML) and optimization tools for mix design, few studies integrate these methods with decision-making techniques and environmental assessment to support practical implementation. This study proposes a hybrid data-driven framework for predicting strength, optimizing mix compositions, and evaluating environmental impacts via life cycle assessment of cement-stabilized soft soils. Six ML models were evaluated, and the top-performing eXtreme Gradient Boosting (XGB) model was further improved using the Grey Wolf Optimizer (GWO). The optimized XGB-GWO model, integrated with a polynomial cost function, served as the objective function in a multi-objective optimization problem solved via the Non-Dominated Sorting Genetic Algorithm II (NSGA-II), with final mix selection guided by the entropy-weighted TOPSIS method. Validation through a case study produced mix designs offering superior strength-cost trade-offs, with the optimal mix achieving 2243.2 kPa unconfined compressive strength and a 16.07 % reduction in carbon emissions compared to the highest-cost design. In conclusion, this study offers a sustainable, scalable approach to soil stabilization and supports informed decision-making in construction.

Life cycle assessment↗