Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Shear Strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Improved impact-resistant boron/aluminum composites for use as turbine engine fan blades

Thin-sheet Charpy and Izod impact tests and standard full-size Charpy impact tests were conducted on unidirectional and angleply composites containing 4, 5.6 and 8 mil boron in 1100, 2024, 5052 and 6061 Al matrices. Impact failure modes of B/Al are proposed to describe the mechanisms involved and to provide insight for maximizing impact resistance. The impact strength of B/Al was significantly increased by proper selection of materials and processing. The use of more ductile matrices and larger diameter boron fibers gave the highest impact strengths by allowing matrix shear deformation and multiple fiber breakage. Pendulum impact test results of improved B/Al were higher than notched titanium and indicate sufficient foreign object damage protection to warrant consideration of B/Al for application to fan blades in aircraft gas turbine engines.

Mcdanels, D. L.↗

Development of an improved toughness hyperpure silica reflective heat shield

High purity three dimensionally woven silica-silica materials were evaluated for use as a tough reflective heat shield for planetary entry probes. A special weave design was selected to minimize light piping effects through the heat shield thickness. Various weave spacings were evaluated for densification efficiency with an 0.7 micron particle size high purity silica. Spectral hemispherical reflectance was measured from 0.2 to 2.5 microns at room temperature. Reflectance increases due to densification and purity of material were measured. Reflectance of 3D hyperpure silica was higher than 3D astroquartz silica for all wavelengths. Mechanical properties were measured in beam flexure and beam shear tests. Results indicated strengths lower than reported for slip cast fused silica. Low strengths were attributed to low densities achieved through vacuum impregnation.

Rusert, E. L.↗

Reusable captive blind fastener

A one piece reusable fastener capable of joining materials together from one side (blind backside) comprises a screw driven pin ending in a wedge-shaped expander cone. The cone cooperates within a slotted collar end which has a number of tangs on a cylindrical body. The fastener is set by inserting it through aligned holes in the workpieces to be joined. Turning the pin in one direction draws the cone into the collar, deforming the tangs radially outward to mate with tapered back-tapered hold in the workpiece, thus fastening the two pieces together. Reversing the direction of the pin withdraws the cone from the collar, and allows the tangs to resume their contracted configuration without withdrawing the fastener from the insertion hole. The fastener is capable of joining materials together from only one side with substantial strength in tension and shear over many resue attachment cycles, with no special operations on the main assembly parts other than the tapering of the back end of the insertion hole.

Peterson, S. A.↗

Effects of thermal cycling on residual mechanical properties of C6000/PMR-15 graphite polyimide

An experimental study to determine the effects of thermal cycling on residual mechanical properties of a graphite/polyimide composite has been conducted. Interlaminar shear, flexure and compression strengths were measured at room temperature and 316 C on unidirectional and quasi-isotropic laminates subjected to 150 and 500 thermal cycles between -156 C and 316 C. Thermal cycling produced transverse microcracks and delaminations in the laminates. The linear density of the microcracks (35/cm) was about the same after 150 and 500 cycles. Although the crack density did not change from 150 to 500 cycles, crack growth did occur with intralamina cracks growing into adjacent lamina. The matrix controlled properties of the quasi-isotropic laminate at both room temperature and 316 C were significantly reduced by thermal cycling. However, the properties of the unidirectional laminate were significantly reduced only at 316 C.

Tompkins, S. S.↗

Adhesive properties of LARC-CPI, a new semi-crystalline polyimide

As part of an effort on high temperature structural resins for aerospace applications, a new family of polyimides containing carbon and ether connecting groups between aromatic rings were prepared. Several of these polyimides were semicrystalline. One polyimide, designated LARC-CPI, with a glass transition temperature of 222 C and a crystalline melt temperature of 350 C, was evaluated in the form of an adhesive, film, and molding. Unoriented films exhibited excellent resistance to solvents and strong bases and high tensile properties. Compact tension specimens gave very high fracture toughness values. Titanium tensile shear specimens provided exceptional strength under a variety of test conditions. The chemistry and the physical and mechanical properties of LARC-CPI are discussed.

Hergenrother, P. M.↗

The low cycle fatigue deformation response of a single-crystal superalloy at 650 C

The cyclic stress-strain response and the associated deformation structure of the single crystal nickel-base superalloy PWA 1480 were investigated. Specimens of various crystallographic orientations were tested in low-cycle fatigue (LCF) at 650 C, resulting in a significant tension-compression anisotropy in initial yield strength associated with the shearing of gamma-prime precipitates by dislocation pairs, and a LCF cyclic hardening of the crystals associated with dislocation interactions occurring in the gamma phase. In specimens deforming by slip on a single slip system, dislocations of the primary slip system accumulated in the gamma matrix and formed seesile entanglements. In specimens deforming by slip on several slip systems, the dislocations of the different operative slip systems intersected in the gamma matrix and formed sessile arrangements.

Gabb, T. P.↗

Preliminary evaluation of adhesion strength measurement devices for ceramic/titanium matrix composite bonds

The adhesive bond between ceramic cement and a titanium matrix composite substrate to be used in the National Aerospace Plane program is evaluated. Two commercially available adhesion testers, the Sebastian Adherence Tester and the CSEM REVETEST Scratch Tester, are evaluated to determine their suitability for quantitatively measuring adhesion strength. Various thicknesses of cements are applied to several substrates, and bond strengths are determined with both testers. The Sabastian Adherence Tester has provided limited data due to an interference from the sample mounting procedure, and has been shown to be incapable of distinguishing adhesion strength from tensile and shear properties of the cement itself. The data from the scratch tester has been found to be difficult to interpret due to the porosity and hardness of the cement. Recommendations are proposed for a more reliable adhesion test method.

Pohlchuck, Bobby↗

Fracture Behavior of a Stitched Warp-Knit Carbon Fabric Composite

Tests were conducted on several types of fracture specimens made from a carbon/epoxy composite. The composite material was stitched prior to introducing epoxy resin. Boeing, used this material to develop a composite wing box for a transport aircraft in the NASA Advanced Composites Transport Program. The specimens included compact, extended compact, and center notched tension specimens. The specimens were cut from panels with three orientations in order to explore the effects of anisotropy. The panels were made with various thicknesses to represent a wing, skin from tip to root. All fractures were not self-similar depending on specimen type and orientation. Unnotched tension specimens were also tested to measure elastic constants and strengths. The normal and shear strains were calculated on fracture planes using a series representation of strain fields for plane anisotropic crack problems. The fracture parameters were determined using a finite element method. Characteristic distances for critical tension and shear strains were calculated for each specimen and a failure criterion based on the interaction of tension and shear strains was proposed.

Poe, Clarence C., Jr.↗

Device and Method for Reducing Aircraft Noise

A noise abatement device that is positioned adjacent to a body. The noise abatement device generally includes tabs or cavities which thicken the shear layer created by fluid flow over, around, or near the body, by creating horseshoe-shaped vortices; this thickening of the shear layer reduces the strength of fluctuations in the flow which produce noise.

Craig L Streett↗

Computational Simulation of Damage Propagation in Three-Dimensional Woven Composites

Three dimensional (3D) woven composites have demonstrated multi-directional properties and improved transverse strength, impact resistance, and shear characteristics. The objective of this research is to develop a new model for predicting the elastic constants, hygrothermal effects, thermomechanical response, and stress limits of 3D woven composites; and to develop a computational tool to facilitate the evaluation of 3D woven composite structures with regard to damage tolerance and durability. Fiber orientations of weave and braid patterns are defined with reference to composite structural coordinates. Orthotropic ply properties and stress limits computed via micromechanics are transformed to composite structural coordinates and integrated to obtain the 3D properties. The various stages of degradation, from damage initiation to collapse of structures, in the 3D woven structures are simulated for the first time. Three dimensional woven composite specimens with various woven patterns under different loading conditions, such as tension, compression, bending, and shear are simulated in the validation process of this research. Damage initiation, growth, accumulation, and propagation to fracture are included in these simulations.

Huang, Dade↗

Extrapolating Accelerated UV Weathering Data: Perspective From PVQAT Task Group 5 (Presentation)

Taskgroup 5 (TG5) is concerned with a accelerated aging standard incorporating factors including ultraviolet radiation, temperature, and moisture. Separate experiments are being conducted in support of a test standard via the regional sub-groups in Asia, Europe, and the United States. The authors will describe the objectives and timeline for the TG5 interlaboratory study being directed out of the USA. Qualitative preliminary data from the experiment is presented. To date, the encapsulation transmittance experiment has: replicated behaviors of fielded materials (including specimen location- and formulation additive-specific discoloration); demonstrated coupling between UV aging and temperature; demonstrated that degradation in EVA results from UV- aging; and obtained good qualitative comparison between Xe and UVA-340 sources for EVA. To date, the encapsulation adhesion experiment (using the compressive shear test to quantify strength of attachment) has demonstrated that attachment strength can decrease drastically (>50%) with age; however, early results suggest significant factor (UV, T, RH) dependence. Much remains to be learned about adhesion.

14 SOLAR ENERGY↗

THE MASS-RICHNESS RELATION OF MaxBCG CLUSTERS FROM QUASAR LENSING MAGNIFICATION USING VARIABILITY

Accurate measurement of galaxy cluster masses is an essential component not only in studies of cluster physics but also for probes of cosmology. However, different mass measurement techniques frequently yield discrepant results. The Sloan Digital Sky Survey MaxBCG catalog's mass-richness relation has previously been constrained using weak lensing shear, Sunyaev-Zeldovich (SZ), and X-ray measurements. The mass normalization of the clusters as measured by weak lensing shear is {approx}>25% higher than that measured using SZ and X-ray methods, a difference much larger than the stated measurement errors in the analyses. We constrain the mass-richness relation of the MaxBCG galaxy cluster catalog by measuring the gravitational lensing magnification of type I quasars in the background of the clusters. The magnification is determined using the quasars' variability and the correlation between quasars' variability amplitude and intrinsic luminosity. The mass-richness relation determined through magnification is in agreement with that measured using shear, confirming that the lensing strength of the clusters implies a high mass normalization and that the discrepancy with other methods is not due to a shear-related systematic measurement error. We study the dependence of the measured mass normalization on the cluster halo orientation. As expected, line-of-sight clusters yield a higher normalization; however, this minority of haloes does not significantly bias the average mass-richness relation of the catalog.

79 ASTRONOMY AND ASTROPHYSICS↗

Elastic Properties across the y→α Volume Collapse in Cerium versus Pressure and Temperature

Here, the longitudinal and transverse sound speeds, c L and c T , of polycrystalline cerium were measured isothermally vs pressure up to the critical temperature across the iso-structural γ-α volume collapse (VC) phase transition. We deduce values for the adiabatic bulk modulus BS, the shear modulus G = ρc T 2 , the Poisson’s ratio ν and the Debye temperature, θ D (p). We find that the elastic constant C 12 is solely responsible for the decrease of B S with pressure towards the VC at RT. With increasing temperature, the lattice contribution ΔS vib (γ→α) to the total entropy change across the VC decreases more rapidly to zero than the total entropy itself suggesting that another mechanism, possibly disorder, assists in stabilizing the γ-phase entropically against the α-phase. Also, with increasing temperature, the Poisson’s ratio becomes negative near the VC transition, meaning that cerium metal takes on auxetic characteristics over a small pressure range. At the critical point the Poisson’s ratio ought to be -1, since the isothermal bulk modulus vanishes and the shear modulus remains nonzero.

36 MATERIALS SCIENCE↗

Multistage Triaxial Tests on Laboratory-Formed Methane Hydrate-Bearing Sediments

A sound understanding of the geomechanical behavior of hydrate–bearing sediments (HBSs) is essential not only for assessing reservoir and wellbore stability during methane gas production but also for projecting the impact of global warming on the stability of geological settings that contain hydrates. This study experimentally investigated the geomechanical responses of laboratory–formed methane–HBS to triaxial shearing under drained conditions. The hydrate pore habit formed in the sediments is noncontact–cementing, which is different from contact–cementing or grain–coating hydrate pore habits formed when the excessive gas method is used. The multistage triaxial test method, which shears a single specimen under different confinements, was employed to examine its applicability in measuring geomechanical properties of the HBS. Conventional single–stage triaxial tests were also performed to serve as baselines. The results show that both the strength and stiffness of HBS increase with increased hydrate saturation and confining stress. Shear dilatancy increases with increased hydrate saturation and decreased confining stress. The peak strength and peak/postpeak shear dilation measured using the multistage tests are comparable to those using the single–stage tests. However, the stiffness measured in later stress stages in the multistage tests was enhanced by the stress–strain history of earlier stages. Therefore, the multistage test offers an efficient way of measuring the strength and volumetric response of the HBS with a much smaller number of specimens than the single–stage test. As a result, this benefits the geomechanical characterization of the HBS, as obtaining the pressure cores is extremely costly and preparing lab samples is usually sophisticated and time consuming.

58 GEOSCIENCES↗

Probabilistic and Possibilistic Analyses of the Strength of a Bonded Joint

The effects of uncertainties on the strength of a single lap shear joint are explained. Probabilistic and possibilistic methods are used to account for uncertainties. Linear and geometrically nonlinear finite element analyses are used in the studies. To evaluate the strength of the joint, fracture in the adhesive and material strength failure in the strap are considered. The study shows that linear analyses yield conservative predictions for failure loads. The possibilistic approach for treating uncertainties appears to be viable for preliminary design, but with several qualifications.

Stroud, W. Jefferson↗

Cholesteric–nematic transitions induced by a shear flow and a magnetic field

The untwisting of the helical structure of a cholesteric liquid crystal under the action of a magnetic field and a shear flow has been studied theoretically. Both factors can induce the cholesteric–nematic transition independently; however, the difference in the orienting actions of the magnetic field and the shear flow leads to competition between magnetic and hydrodynamic mechanisms of influence on the cholesteric liquid crystal. We have analyzed different orientations of the magnetic field relative to the direction of the flow in the shear plane. In a number of limiting cases, the analytic dependences are obtained for the pitch of the cholesteric helix deformed by the shear flow. The phase diagrams of the cholesteric–nematic transitions and the pitch of the cholesteric helix are calculated for different values of the magnetic field strength and the angle of orientation, the flow velocity gradient, and the reactive parameter. It is shown that the magnetic field stabilizes the orientation of the director in the shear flow and expands the boundaries of orientability of cholesterics. It has been established that the shear flow shifts the critical magnetic field strength of the transition. It is shown that a sequence of reentrant orientational cholesteric–nematic–cholesteric transitions can be induced by rotating the magnetic field in certain intervals of its strength and shear flow velocity gradients.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The Ideal Strengths of Superconducting MgCNi{sub 3} and CdCNi{sub 3}

The stress-strain curves under tensile deformation in the 〈100〉, 〈110〉, and 〈111〉 directions and under shear deformation in the (001)〈110〉, (110)〈1̄10〉, (111)〈11̄0〉, and (111)〈112̄〉 slip systems have been systematically calculated by first-principles method to study the ideal strengths of superconducting MgCNi{sub 3} and CdCNi{sub 3}. The ideal strengths in the three tensile directions are found to be reduced in the order of 〈100〉 → 〈110〉 → 〈111〉 and those for the four shear slip systems in the order of (110)〈1̄10〉→(111)〈112̄〉→(111)〈11̄0〉→(001)〈110〉 for both superconductors. Their lowest ideal tensile strengths are found to be larger than the corresponding highest ideal shear strengths, which could explain why both superconductors have the ductility. The obtained lattice constants and elastic properties coincide well with the the available experimental and theoretical values.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Broadband Shock Noise in Internally-Mixed Dual-Stream Jets

Broadband shock noise (BBSN) has been studied in some detail in single-flow jets and recently in dual-stream jets with separate flow exhaust systems. Shock noise is of great concern in these latter cases because of the noise created for the aircraft cabin by the underexpanded nozzle flow at cruise. Another case where shock noise is of concern is in the case of future supersonic aircraft that are expected to have bypass ratios small enough to justify internally mixed exhaust systems, and whose mission will push cycles to the point of imperfectly expanded flows. Dual-stream jets with internally mixed plume have some simplifying aspects relative to the separate flow jets, having a single shock structure given by the common nozzle pressure. This is used to separate the contribution of the turbulent shear layer to the broadband shock noise. Shock structure is held constant while the geometry and strength of the inner and merged shear layers are varying by changing splitter area ratio and core stream temperature. Flow and noise measurements are presented which document the efforts at separating the contribution of the inner shear layer to the broadband shock noise.

Bridges, James E.↗