Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Process sensitivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Design and Development of 256x256 Linear Mode Low-Noise Avalanche Photodiode Arrays

A larger format photodiode array is always desirable for many LADAR imaging applications. However, as the array format increases, the laser power or the lens aperture has to increase to maintain the same flux per pixel thus increasing the size, weight and power of the imaging system. In order to avoid this negative impact, it is essential to improve the pixel sensitivity. The sensitivity of a short wavelength infrared linear-mode avalanche photodiode (APD) is a delicate balance of quantum efficiency, usable gain, excess noise factor, capacitance, and dark current of APD as well as the input equivalent noise of the amplifier. By using InA1As as a multiplication layer in an InP-based APD, the ionization coefficient ratio, k, is reduced from 0.40 (lnP) to 0.22, and the excess noise is reduced by about 50%. An additional improvement in excess noise of 25% was achieved by employing an impact-ionization-engineering structure with a k value of 0.15. Compared with the traditional InP structure, about 30% reduction in the noise-equivalent power with the following amplifier can be achieved. Spectrolab demonstrated 30-um mesa APD pixels with a dark current less than 10 nA and a capacitance of 60 fF at gain of 10. APD gain uninformity determines the usable gain of most pixels in an array, which is critical to focal plane array sensitivity. By fine tuning the material growth and device process, a break-down-voltage standard deviation of 0.1 V and gain of 30 on individual pixels were demonstrated in our 256x256 linear-mode APD arrays.

Yuan, Ping↗
NASA NTRS2017

Model-Based Thermal System Design Optimization for the James Webb Space Telescope

Spacecraft thermal model validation is normally performed by comparing model predictions with thermal test data and reducing their discrepancies to meet the mission requirements. Based on thermal engineering expertise, the model input parameters are adjusted to tune the model output response to the test data. The end result is not guaranteed to be the best solution in terms of reduced discrepancy and the process requires months to complete. A model-based methodology was developed to perform the validation process in a fully automated fashion and provide mathematical bases to the search for the optimal parameter set that minimizes the discrepancies between model and data. The methodology was successfully applied to several thermal subsystems of the James Webb Space Telescope (JWST). Global or quasiglobal optimal solutions were found and the total execution time of the model validation process was reduced to about two weeks. The model sensitivities to the parameters, which are required to solve the optimization problem, can be calculated automatically before the test begins and provide a library for sensitivity studies. This methodology represents a crucial commodity when testing complex, large-scale systems under time and budget constraints. Here, results for the JWST Core thermal system will be presented in detail.

Cataldo, Giuseppe↗
NASA NTRSDate not supplied

Porosity Model Parameter Effects on Metal Additive Manufacturing Simulations

This work investigates the effects of model parameters on thermomechanical simulations of a metal additive manufacturing process. The first half of this work explores the sensitivity and effects of the two porosity parameters used in the evolving constitutive model of the simulation. Varying the two parameters of the model show that for the simulations conducted here, the linear coefficient drives the predicted residual stress results while the constant term has little impact. The second half of the work considers the size, order, and the number of element layers in the finite element mesh. The stress distribution plots show that second-order elements along with a dense mesh marginally improve mesh convergence at a significant cost.

Additive Manufacturing↗
NASA NTRS2020

Reduction of structural impacts and distinction of photosynthetic pathways in a global estimation of GPP from space-borne solar-induced chlorophyll fluorescence

Quantifying global photosynthesis remains a challenge due to a lack of accurate remote sensing proxies. Solar-induced chlorophyll fluorescence (SIF) has been shown to be a good indicator of photosynthetic activity across various spatial scales. However, a global and spatially challenging estimate of terrestrial gross primary production (GPP) based on satellite SIF remains unresolved due to the confounding effects of species-specific physical and physiological traits and external factors, such as canopy structure or photosynthetic pathway (C3orC4). Here we analyze an ensemble of far-red SIF data from OCO-2 satellite and ground observations at multiple sites, using the spectral invariant theory to reduce the effects of canopy structure and to retrieve a structure-corrected total canopy SIF emission (SIF total). We find that the relationships between observed canopy-leavingSIF and ecosystem GPP vary significantly among biomes. In contrast, the relationships between SIF total and GPP converge around two unique models, one for C3and one for C4plants. We show that the two single empirical models can be used to globally scale satellite SIF observations to terrestrial GPP. We obtain an independent estimate of global terrestrial GPP of 129.56 ± 6.54 PgC/year for the 2015–2017 period, which is consistent with the state-of-the-art data- and process-oriented models. The new GPP product shows improved sensitivity to previously undetected ‘hotspots’ of productivity, being able to resolve the double-peak in GPP due to rotational cropping systems. We suggest that the direct scheme to estimate GPP presented here, which is based on satelliteSIF, may open up new possibilities to resolve the dynamics of global terrestrial GPP across space and time.

scale satellite SIF observations to terrestrial GP↗
NASA NTRS2023

Galvanic Vestibular Reduction Modifies Perception of Coriolis Cross-Coupling and Delays Motion Sickness Onset

INTRODUCTION: Alterations in vestibular sensory processing following G-transitions lead to head movement sensitivity and motion sickness upon return to Earth’s gravity. The purpose of this study was to evaluate whether a non-pharmaceutical tool using galvanic vestibular reduction (GVR) could suppress disorienting illusions and mitigate motion sickness. A similar approach using anodal (inhibitory) currents delivered to both ears has been shown to result in a selective reversible ablation of irregular vestibular afferents [1]. METHODS: Using a repeated measures counter-balanced design, motion sickness and perception were obtained in 26 subjects during Coriolis cross-coupling stimuli on a rotating chair across three GVR treatment interventions: throughout stimulus testing (prevention), following symptom onset (rescue), and placebo control. The GVR peak current was maintained at 2.5 mA across subjects and across prevention / rescue sessions. Subjects performed up to 10 sets of pitch head movements during constant rotation. For each set, head movement was cued every 10 seconds, alternating between pitch forward (chin resting to chest) and pitch backward (head upright) for a total of 7 forward and backward movements. During each head movement, subjects were asked to use a joystick to record the magnitude of their perceived rotation along three axes. During the 2-minute pause between sets, motion sickness symptom scoring was obtained using the Pensacola Diagnostic Index and subject discomfort (0-20) ratings. Performance on a sensorimotor and cognitive test battery was measured during a fourth session to map changes in GVR level with functional performance. RESULTS: Fourteen of the 26 subjects were not susceptible to the motion stressor (i.e., did not reach an endpoint in the control condition). While the time to endpoint, or number of head movements, did not significantly vary across the three GVR conditions in the remaining subjects, the symptom levels were significantly lower through the third set of head movements when GVR was on throughout the testing. Initiating GVR following symptom onset did not appear to alter the symptom progression nor time to motion sickness endpoint. Based on the joystick measures, GVR significantly modified the perceived roll and pitch sensation during head movements, reducing the amplitude of tilt in most subjects. It is important to note that comparable levels of GVR did not impair performance on a functional test battery including mobility, balance and cognitive tasks. DISCUSSION: Our findings suggest GVR may be useful in reducing disorienting roll and pitch illusions and delaying the onset of motion sickness. Further enhancements will be required to individualize the stimulation amplitude and optimize the waveform delivery. Adapting this non-pharmaceutical countermeasure approach to allow self-administered titration of current amplitude during recovery would enable transfer to post-flight treatment of motion sickness. [1] Minor L. B. and Goldberg J. M. (1991) J Neurosci 11, 1636-48. 109, 889-894.

G N Pradhan↗
DOE OSTI2022

ORNL Neutron Cross Section Measurements of 90 Zr NCSP ND-1 Task [Slides]

Luiz Leal's idea to integrate the experimental uncertainties, covariances, and sensitivities in the ND workflow and to centralize the process at one location created a cohesive tool for data testing. It has been practiced for more than two decades by the NCS and ND groups at ORNL. The development and use of the ORNL codes TSUNAMI and TSURFER within SCALE made it possible. Today, it has been extended to SAMINT, which enables the coupling of differential and integral data evaluation in a continuous-energy framework.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Kinetic and temperature sensitivity properties of soil exoenzymes through the soil profile down to one-meter depth at a temperate coniferous forest (Blodgett, CA)

This dataset contains data on kinetic and temperature sensitivity parameters of the exoenzymes β-glucosidase (BG), leucine/leucyl aminopeptidase (LAP) and acid phosphatase (AP) across a soil profile down to 90 cm depth at Blodgett forest, CA, USA. These data were generated to determine if kinetic and thermal properties of microbial exoenzymes involved in organic matter decomposition varied with soil depth, following variation in soil properties and microbial communities, as part of the study: Alves et al. (2021). Kinetic Properties of Microbial Exoenzymes Vary with Soil Depth but Have Similar Temperature Sensitivities Through the Soil Profile. Frontiers in Microbiology 12:3618. https://doi.org/10.3389/fmicb.2021.735282. This research was performed within the framework of the TES Belowground Biogeochemistry SFA project, in particular association with a long-term field warming experiment of the whole soil profile at Blodgett forest. Samples for this work were collected from locations representative of the field experimental plots. Potential enzyme activity rates were measured using laboratory fluorometric assays with soils collected at 0-10, 10-20, 30-40, 50-60, 60-70 and 80-90 cm deep in biological triplicates (i.e., three soil cores collected at different representative locations). Assays with each soil were conducted over a gradient of eight substrate concentrations per enzyme, and incubated at 4, 10, 16, 25, 35 or 50°C. Enzyme Michaelis-Menten kinetics were modeled over the eight substrate concentrations at each temperature, and the temperature sensitivity of the kinetic parameters was modeled over the six temperatures using linear Arrhenius/Q10 and non-linear Macromolecular Rate Theory (MMRT) models. The dataset includes the fully processed enzyme activity rate data used to model Michaelis-Menten kinetics, calculated kinetic and temperature sensitivity parameters, and basic soil and microbial biomass chemistry for each sample. All data is provided for each individual biological replicate, and kinetic and temperature sensitivity parameters are also provided as means of the biological replicates. The dataset also includes all raw measurement data and code used to parse, combine and perform the analyses described by Alves et al. (2021). For file descriptions, see the file-level metadata files: “enzymes_dataProcessed_flmd.xlsx” (processed data); “enzymes_dataRaw_flmd.xlsx” (compressed raw data and metadata); and “enzymes_code_flmd.xlsx” (compressed code). The experimental design, list of parameters measured, soil and microbial biomass chemistry data, and means of biological replicates for kinetic and temperature sensitivity parameters are also provided as human-readable tables in file “enzymeTraits_design_results_tables.xlsx”.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1979

Simulated electronic heterodyne recording and processing of pulsed-laser holograms

The electronic recording of pulsed-laser holograms is proposed. The polarization sensitivity of each resolution element of the detector is controlled independently to add an arbitrary phase to the image waves. This method which can be used to simulate heterodyne recording and to process three-dimensional optical images, is based on a similar method for heterodyne recording and processing of continuous-wave holograms.

Decker, A. J.↗
DOE OSTI2025

Optimising the processing and storage of visibilities using lossy compression

The next-generation radio astronomy instruments are providing a massive increase in sensitivity and coverage, largely through increasing the number of stations in the array and the frequency span sampled. The two primary problems encountered when processing the resultant avalanche of data are the need for abundant storage and the constraints imposed by I/O, as I/O bandwidths drop significantly on cold storage. An example of this is the data deluge expected from the SKA Telescopes of more than 60 PB per day, all to be stored on the buffer filesystem. While compressing the data is an obvious solution, the impacts on the final data products are hard to predict. In this paper, we chose an error-controlled compressor – MGARD – and applied it to simulated SKA-Mid and real pathfinder visibility data, in noise-free and noise-dominated regimes. As the data have an implicit error level in the system temperature, using an error bound in compression provides a natural metric for compression. MGARD ensures the compression incurred errors adhere to the user-prescribed tolerance. To measure the degradation of images reconstructed using the lossy compressed data, we proposed a list of diagnostic measures, exploring the trade-off between these error bounds and the corresponding compression ratios, as well as the impact on science quality derived from the lossy compressed data products through a series of experiments. We studied the global and local impacts on the output images for continuum and spectral line examples. We found relative error bounds of as much as 10%, which provide compression ratios of about 20, have a limited impact on the continuum imaging as the increased noise is less than the image RMS, whereas a 1% error bound (compression ratio of 8) introduces an increase in noise of about an order of magnitude less than the image RMS. For extremely sensitive observations and for very precious data, we would recommend a 0.1% error bound with compression ratios of about 4. These have noise impacts two orders of magnitude less than the image RMS levels. At these levels, the limits are due to instabilities in the deconvolution methods. We compared the results to the alternative compression tool DYSCO, in both the impacts on the images and in the relative flexibility. MGARD provides better compression for similar error bounds and has a host of potentially powerful additional features.

Techniques: interferometric↗
NASA NTRS1973

Comparison of Lidar Methods for Remote Measurement of Air Pollutants

This paper presents quantitative comparisons of several single-ended lidar techniques for the remote measurement of gaseous pollutants. These techniques are divided into two groups. The first group is based on the measurement of energy scattered directly by the gas of interest. The gaseous scattering processes considered are ordinary fluorescence, resonance fluorescence (also called resonance scattering), Raman scattering, and resonant (or nearly resonant) Raman scattering. The second group is based on the measurement of a characteristic differential absorption produced by the gas of interest at two discrete wavelengths, using energy scattered back toward the receiver by a remote reflector other than the gas of interest. The remote reflector may be intermixed with the gas of interest, as is the case with aerosols and atmospheric gases (principally nitrogen), or they may be fixed reflectors such as terrestrial objects or retroflectors. The detectability of a given material will depend on the magnitude and characteristics of the optical interaction with that material. The main characteristics of interest are the cross section, the response time, and the spectral response of the material relative to both the transmit and receive functions of the lidar. These characteristics and their implications for remote sensing will be reviewed for the four direct scatter processes and for the differential absorption technique. The characteristic behavior of the direct backscatter technique is different from the differential absorption technique with respect to sensitivity, concentration of material, and the effect of range. For these reasons, the direct backscatter processes cannot be compared directly to the differential absorption technique. The two techniques can be compared for specific material and system configurations, however. This paper describes specific lidar system configurations and gives the calculated performance level for these systems in both the direct backscatter and differential absorption modes for a wide variety of pollutant monitoring situations. The results of this comparison of techniques indicate that the differential- absorption lidar technique can provide adequate range and sensitivity for a wide variety of pollution monitoring applications involving a number of interesting pollutant materials. No other single technique appears to provide these capabilities for such a wide range of materials.

Wright, M. L.↗
DOE OSTI2024

Cold-Season Precipitation Sensitivity to Microphysical Parameterizations: Hydrologic Evaluations Leveraging Snow Lidar Datasets

Abstract Cloud microphysical processes are an important facet of atmospheric modeling, as they can control the initiation and rates of snowfall. Thus, parameterizations of these processes have important implications for modeling seasonal snow accumulation. We conduct experiments with the Weather Research and Forecasting (WRF V4.3.3) Model using three different microphysics parameterizations, including a sophisticated new scheme (ISHMAEL). Simulations are conducted for two cold seasons (2018 and 2019) centered on the Colorado Rockies’ ∼750-km 2 East River watershed. Precipitation efficiencies are quantified using a drying-ratio mass budget approach and point evaluations are performed against three NRCS SNOTEL stations. Precipitation and meteorological outputs from each are used to force a land surface model (Noah-MP) so that peak snow accumulation can be compared against airborne snow lidar products. We find that microphysical parameterization choice alone has a modest impact on total precipitation on the order of ±3% watershed-wide, and as high as 15% for certain regions, similar to other studies comparing the same parameterizations. Precipitation biases evaluated against SNOTEL are 15% ± 13%. WRF Noah-MP configurations produced snow water equivalents with good correlations with airborne lidar products at a 1-km spatial resolution: Pearson’s r values of 0.9, RMSEs between 8 and 17 cm, and percent biases of 3%–15%. Noah-MP with precipitation from the PRISM geostatistical precipitation product leads to a peak SWE underestimation of 32% in both years examined, and a weaker spatial correlation than the WRF configurations. We fall short of identifying a clearly superior microphysical parameterization but conclude that snow lidar is a valuable nontraditional indicator of model performance.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1994

Ice nucleation in the upper troposphere: Sensitivity to aerosol number density, temperature, and cooling rate

We have investigated the processes that control ice crystal nucleation in the upper troposphere using a numerical model. Nucleation of ice resulting from cooling was simulated for a range of aerosol number densities, initial temperatures, and cooling rates. In contrast to observations of stratus clouds, we find that the number of ice crystals that nucleate in cirrus is relatively insensitive to the number of aerosols present. The ice crystal size distribution at the end of the nucleation process is unaffected by the assumed initial aerosol number density. Essentially, nucleation continues until enough ice crystals are present such that their deposition growth rapidly depletes the vapor and shuts off any further nucleation. However, the number of ice crystals nucleated increases rapidly with decreasing initial temperature and increasing cooling rate. This temperature dependence alone could explain the large ice crystal number density observed in very cold tropical cirrus.

Jensen, E. J.↗
DOE OSTI2020

Effects of Cloud Liquid-Phase Microphysical Processes in Mixed-Phase Cumuli Over the Tibetan Plateau

Numerical simulations often overpredict precipitation over the Tibetan Plateau (TP). To examine the factors causing precipitation overprediction, different parameterizations of liquid-phase microphysical processes (accretion, autoconversion, and entrainment-mixing) are implemented into the Morrison microphysics scheme to simulate a TP precipitation event in summer with the Weather Research and Forecasting (WRF) model. The general spatial distribution and temporal trend of precipitation are captured by all simulations, but the precipitation rate is overpredicted. The results from sensitivity experiments suggest that compared to other examined liquid-phase processes, the accretion process is more important in precipitation simulation over the TP region. Further investigation with the Heidke skill scores reveals that accretion parameterization that takes into account the raindrop size produces the most accurate results in terms of the total surface precipitation. This parameterization suppresses spurious accretion and does not produce liquid-phase precipitation until cloud droplets are big enough. Here, it is also confirmed that increasing the model resolution can reduce precipitation overprediction. Results from the case study are confirmed by the use of a one-month simulation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

(U) Average Scattering Angle Cosine Sensitivities

The Evaluated Nuclear Data File (ENDF) provides covariances of the average scattering angle cosine $\overline{μ}$ for 117 nuclides, and the NJOY nuclear data processing code can process these covariances. To propagate them to the uncertainty of a response due to uncertainties in $\overline{μ}$ requires sensitivities of the response with respect to $\overline{μ}$. This report uses NJOY’s definition of $\overline{μ}$ and derives a relationship between the sensitivity of a response to $\overline{μ}$ and the sensitivity of the response to the anisotropic P 1 elastic scattering cross section. This relationship has been implemented in the multigroup neutron sensitivity code SENSMG, which relies on the discrete ordinates code PARTISN for the neutron transport calculations. Kodeli has also calculated sensitivities with respect to $\overline{μ}$ and associated uncertainties. However, the formal derivation of this paper shows that the definition of the sensitivity with respect to $\overline{μ}$ is ambiguous because there are multiple ways to change $\overline{μ}$ by changing scattering cross sections. Here we derive two such ways. Both are implemented in SENSMG. This report is organized as follows. Section II discusses $\overline{μ}$ and its significance. Section III presents the equations used for the sensitivity of a response with respect to $\overline{μ}$, and Section IV discusses how to compute these sensitivities with SENSMG and MCNP6.3. Section V is a fast-spectrum test problem, and Sec. VI is a thermal-spectrum problem. Section VII is a summary. The example problem inputs are listed in the appendix.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

High-Temperature Fe-Based Fischer–Tropsch Synthesis: Experimentally Validated Kinetic Models Implemented at Pellet and Reactor Scales

Pellet- and reactor-scale models for Fischer–Tropsch synthesis (FTS) with a Fe–K/silica catalyst were developed to investigate the sensitivity of the hydrocarbon products and carbon dioxide selectivity to process conditions and feed composition at high temperature (350–400 °C), moderate pressure (1–10 bar), and a range of H 2 /CO ratios (3–1). The major objective of this paper is to develop, validate, and evaluate a high-temperature FTS model that is then used to assess the feasibility of process integration with syngas production. Since there is limited kinetic data available, in literature at these conditions, bench-scale reactor tests were conducted to obtain operational data for parameter fitting of kinetic expressions used in the model. This resulting kinetic model demonstrated agreement with the experimental data with an R 2 of 0.97 to the testing data set and, thus, was feasible to apply at pellet and reactor scales. Here, multiple pellet sizes were modeled to detail the role of transport limitations as the sphere’s diameter approached and exceeded 1 mm. Application of the reactor model indicated that hydrocarbon selectivity depended strongly on temperature, whereas the ratio of olefin to paraffin products decreased with increasing temperature, pressure, and H 2 /CO ratio. Product selectivity was not sensitive to the conversion of carbon monoxide. Furthermore, the roles of the pressure and H 2 /CO ratio were closely coupled. At a H 2 /CO ratio of 3, only slight variations in selectivity occurred over a pressure range of 1–20 bar, whereas at a ratio of 1, selectivity could vary by as much as 30% over the same pressure range. At pressures below 5 bar and temperatures above 350 °C, minimal selectivity to heavy hydrocarbons (C 12+ ) is obtained, and selectivity to midrange products (C 5–11 ) rapidly declined as pressure dropped below 5 bar, which indicated that an operational pressure of at least 5 bar is needed to achieve reasonable yields in this temperature range. These results, while tentative, provide guidelines for further experimentation and evaluation of integrated FTS processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Performance Analysis and Radiation Damage Estimation of the Stopping Target Monitor Detectors in Mu2e

The Mu2e experiment aims to search for the charged lepton flavour violating (CLFV) process of a coherent, neutrinoless, conversion of a muon into an electron within the proximity of an aluminium nucleus. Mu2e seeks to measure the ratio (R μe ) of the rate of this conversion process, relative to that of ordinary muon capture. Mu2e will achieve world-leading sensitivity, improving the current limit of Rμe < 7 ×10 -13 (90% C.L.),set by the SINDRUM-II experiment, by an order of 104. This corresponds to a single-event sensitivity of Rμe < 2.87 × 10 -17 (90% C.L.). Many beyond Standard Model (BSM) theories require CLFV to occur at a rate accessible by Mu2e. Any observation of CLFV at Mu2e would have profound implications on particle physics. The Stopping Target Monitor (STM) will be comprised of both a HPGe and a LaBr3 detector which will monitor the signals of photons produced in stopped-muon processes to a required accuracy of 10%. To achieve the desired sensitivity, it is imperative that the detectors perform at their optimal level. The STM detectors are placed within a harsh radiation environment in the form of a high energy ‘flash’ of gamma radiation as well as a flux of fast neutrons. Estimations of radiation damage to HPGe in literature is limited. This thesis reports an approach which utilizes the Kinetic-Energy Released in Matter (KERMA) parameter that considers the energy dependence of the incident flux and the cross-section information for the incident particle. Resampling schemes have been adopted to give a realistic rate over the experiment run time. The results have then been normalized to the radiation damage caused by a 252 Cf source. The estimated time before annealing of the detector is necessary is found to be 75 and 78 months in the case of neutron damage and τ ~ 24 years, 11 months in the case of electron/positron induced damage. This shows significant improvement on the previous estimations.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Computations of turbulent evaporating sprays

A computational study of turbulent evaporating sprays is reported. The major focus is to examine the sensitivity of the vaporization behavior of turbulent sprays to the transient liquid-phase processes. Three models considered to represent these processes are the thin skin, infinite diffusion, and diffusion limit models. Favre-averaged equations with k-epsilon-g turbulence model are employed for the gas phase. The Lagrangian approach with a stochastic separated flow method is used for the liquid phase where the effects of gas turbulence on droplet trajectories and interphase transport rates are considered using random-walk computations. Also the variable-property effects are considered in detail. Results indicate that, depending upon the boiling temperature and heat of vaporization of the fuel considered, the vaporization behavior of turbulent sprays may be quite sensitive to the modeling of transient liquid-phase processes. Thus, it is important that for most hydrocarbon fuels these processes be adequately represented in any comprehensive spray computations. The present results also provide further support to the conclusions of earlier studies which have been based on simplified spray configurations.

Aggarwal, S. K.↗