Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSURE DEPENDENCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Test Plan for the Boiling Water Reactor Dry Cask Simulator

The thermal performance of commercial nuclear spent fuel dry storage casks are evaluated through detailed numerical analysis . These modeling efforts are completed by the vendor to demonstrate performance and regulatory compliance. The calculations are then independently verified by the Nuclear Regulatory Commission (NRC). Carefully measured data sets generated from testing of full sized casks or smaller cask analogs are widely recognized as vital for validating these models. Recent advances in dry storage cask designs have significantly increased the maximum thermal load allowed in a cask in part by increasing the efficiency of internal conduction pathways and by increasing the internal convection through greater canister helium pressure. These same vertical, canistered cask systems rely on ventilation between the canister and the overpack to convect heat away from the canister to the environment for both above and below-ground configurations. While several testing programs have been previously conducted, these earlier validation attempts did not capture the effects of elevated helium pressures or accurately portray the external convection of above-ground and below-ground canistered dry cask systems. The purpose of the investigation described in this report is to produce a data set that can be used to test the validity of the assumptions associated with the calculations presently used to determine steady-state cladding temperatures in modern vertical, canistered dry cask systems. The BWR cask simulator (BCS) has been designed in detail for both the above-ground and below-ground venting configurations. The pressure vessel representing the canister has been designed, fabricated, and pressure tested for a maximum allowable pressure (MAWP) rating of 24 bar at 400 deg C. An existing electrically heated but otherwise prototypic BWR Incoloy-clad test assembly is being deployed inside of a representative storage basket and cylindrical pressure vessel that represents the canister. The symmetric single assembly geometry with well-controlled boundary conditions simplifies interpretation of results. Various configurations of outer concentric ducting will be used to mimic conditions for above and below-ground storage configurations of vertical, dry cask systems with canisters. Radial and axial temperature profiles will be measured for a wide range of decay power and helium cask pressures. Of particular interest is the evaluation of the effect of increased helium pressure on allowable heat load and the effect of simulated wind on a simplified below ground vent configuration. While incorporating the best available information, this test plan is subject to changes due to improved understanding from modeling or from as-built deviations to designs. As-built conditions and actual procedures will be documented in the final test report.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Band gap opening in strongly compressed diamond observed by x-ray energy loss spectroscopy

The extraordinary mechanical and optical properties of diamond are the basis of numerous technical applications and make diamond anvil cells a premier device to explore the high-pressure behavior of materials. However, at applied pressures above a few hundred GPa, optical probing through the anvils becomes difficult because of the pressure-induced changes of the transmission and the excitation of a strong optical emission. Such features have been interpreted as the onset of a closure of the optical gap in diamond, and can significantly impair spectroscopy of the material inside the cell. In contrast, a comparable widening has been predicted for purely hydrostatic compressions, forming a basis for the presumed pressure stiffening of diamond and resilience to the eventual phase change to BC8. We here present the first experimental evidence of this effect at geo-planetary pressures, exceeding the highest ever reported hydrostatic compression of diamond by more than 200 GPa and any other measurement of the band gap by more than 350 GPa. We here apply laser driven-ablation to create a dynamic, high pressure state in a thin, synthetic diamond foil together with frequency-resolved x-ray scattering as a probe. The frequency shift of the inelastically scattered x-rays encodes the optical properties and, thus, the behavior of the band gap in the sample. Using the ultra-bright x-ray beam from the Linac Coherent Light Source (LCLS), we observe an increasing direct band gap in diamond up to a pressure of 370 GPa. This finding points to the enormous strains in the anvils and the impurities in natural Type Ia diamonds as the source of the observed closure of the optical window. Our results demonstrate that diamond remains an insulating solid to pressures approaching its limit strength.

36 MATERIALS SCIENCE↗

High Pressure X-ray Absorption Studies on Correlated-Electron Systems

This project used high pressure to alter the electron-electron and electron-lattice interactions in rare earth and actinide compounds. Knowledge of these properties is the starting points for a first-principles understanding of electronic and electronically related macroscopic properties. The research focused on a systematic study of x-ray absorption measurements on rare earth and actinide compounds.

36 MATERIALS SCIENCE↗

Supplement to LA-UR-17-21218: Application to SSVD

We apply the formalism derived in LA-UR-17-21218 to the prescription for an RMI-based self-similar velocity distribution (SSVD) derived by Ham- merberg et al.. We compute analytically the true [mt(t)] and inferred [mi(t)] ejecta mass arriving at the piezoelectric sensor for several shots de- scribed in the literature and compare the results to the data. We nd that while the \RMI + SSVD" prescription gives rise to decent estimates for the nal accumulated mass at the pin, the time-dependent accumulation rises too sharply and linearly to agree with data. We also compute the time-dependent pressure and voltage at the sensor, and compare the latter to data. The pres- sure does not rise smoothly from zero, instead exhibiting a strong surge as the leading edge of the ejecta cloud arrives, which produces an initial sharp spike in the voltage trace, which is not observed. These inconsistencies result from a discontinuity in the prescribed self-similar velocity distribution at maximum relative velocity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Sierra/SolidMechanics 4.48 User's Guide: Addendum for Shock Capabilities.

This is an addendum to the Sierra/SolidMechanics 4.48 User's Guide that documents additional capabilities available only in alternate versions of the Sierra/SolidMechanics (Sierra/SM) code. These alternate versions are enhanced to provide capabilities that are regulated under the U.S. Department of State's International Traffic in Arms Regulations (ITAR) export-control rules. The ITAR regulated codes are only distributed to entities that comply with the ITAR export-control requirements. The ITAR enhancements to Sierra/SM in- clude material models with an energy-dependent pressure response (appropriate for very large deformations and strain rates) and capabilities for blast modeling. Since this is an addendum to the standard Sierra/SM user's guide, please refer to that document first for general descriptions of code capability and use.

97 MATHEMATICS AND COMPUTING↗

Shock Initiation Response of PBX 9502 Considering Rarefaction Wave Effects

The effect of rarefaction waves on the shock initiation processes of impacted explosives is investigated. The Scaled Uniform Reactive Front (SURF) explosives model is convenient for this investigation because mechanisms responsible for ignition, i.e., the physics of hot spots, is based on the shock pressure, while rarefactions are controlled by local pressure and treated separately in SURF. One -dimensional gas gun experiments are used to calibrate the ignition portion of SURF. Impact experiments conducted using thin disk and small diameter rods, where controlled one- and two-dimensional rarefactions are introduced, allow the local pressure-dependence of SURF to be parameterized.The Theory of Singular Surfaces was invoked to elucidate the thermo-mechanical and thermo-chemical behavior. Room and elevated (250°C) temperature conditions were explored. In all cases SURF could be parameterized to match the experimental results. In doing so, the role of rarefactions on the shock initiation process was gleaned.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Numerical Simulations of Cratering Effects in Adobe

This paper outlines a new simplified approach to developing a material model for adobe. The approach is to fit the equation of state (EOS) using a Mie-Gruneisen (MGR) analytical model with a P-Alpha compaction law, and to fit the pressure-dependent yield surface with the Geological Yield Surface (GEO) modeled in CTH using well characterized adobe. By identifying key parameters that governed material response, this simplified modeling approach aimed to increase the understanding of the shock compaction and compression behavior of adobe. The new simplified model for adobe represented in this paper replicated the features of past experimental penetration data. At low velocities the penetration behavior of steel spheres into adobe is captured by Stokes law, where the drag coefficient is inversely proportional to the Reynolds number. Each inherently different adobe material investigated had a separate linear region with the slope equal to the inverse of the coefficient of drag multiplied by impact velocity. A transition region following the Stokes region was identified in each adobe material, where the penetration depth was constant with increasing impact velocity. This penetration depth limit was shown to be dependent upon the yield strength of the adobe and inversely proportional to the initial density. Finally, examining the sensitivity of the penetration depth to the key model parameters, the material model for adobe was adjusted to provide the best fit to the experimental penetration data. In addition, a simplified water content, or initial saturation of the adobe, was introduced as another relevant parameter to characterize the response. Using this simple material model for adobe, validated with experimental penetration data, the response of adobe targets to hypervelocity impact of a variety of projectile types can be reliably predicted.

36 MATERIALS SCIENCE↗

Sierra/SolidMechanics 4.54 User's Guide: Addendum for Shock Capabilities.

This is an addendum to the Sierra/SolidMechanics 4.54 User's Guide that documents additional capabilities available only in alternate versions of the Sierra/SolidMechanics (Sierra/SM) code. These alternate versions are enhanced to provide capabilities that are regulated under the U.S. Department of State's International Traffic in Arms Regulations (ITAR) export control rules. The ITAR regulated codes are only distributed to entities that comply with the ITAR export control requirements. The ITAR enhancements to Sierra/SM include material models with an energy-dependent pressure response (appropriate for very large deformations and strain rates) and capabilities for blast modeling. This document is an addendum only; the standard Sierra/SolidMechanics 4.54 User's Guide should be referenced for most general descriptions of code capability and use.

42 ENGINEERING↗

Sierra/SolidMechanics 4.56 User's Guide: Addendum for Shock Capabilities

This is an addendum to the Sierra/SolidMechanics 4.56 User's Guide that documents additional capabilities available only in alternate versions of the Sierra/SolidMechanics (Sierra/SM) code. These alternate versions are enhanced to provide capabilities that are regulated under the U.S. Department of State's International Traffic in Arms Regulations (ITAR) export control rules. The ITAR regulated codes are only distributed to entities that comply with the ITAR export control requirements. The ITAR enhancements to Sierra/SM include material models with an energy-dependent pressure response (appropriate for very large deformations and strain rates) and capabilities for blast modeling. This document is an addendum only; the standard Sierra/SolidMechanics 4.56 User's Guide should be referenced for most general descriptions of code capability and use.

97 MATHEMATICS AND COMPUTING↗

Sierra/SolidMechanics 4.52 User's Guide: Addendum for Shock Capabilities

This is an addendum to the Sierra/SolidMechanics 4.52 User's Guide that documents additional capabilities available only in alternate versions of the Sierra/SolidMechanics (Sierra/SM) code. These alternate versions are enhanced to provide capabilities that are regulated under the U.S. Department of State's International Traffic in Arms Regulations (ITAR) export control rules. The ITAR regulated codes are only distributed to entities that comply with the ITAR export control requirements. The ITAR enhancements to Sierra/SM include material models with an energy-dependent pressure response (appropriate for very large deformations and strain rates) and capabilities for blast modeling. This document is an addendum only; the standard Sierra/SolidMechanics 4.52 User's Guide should be referenced for most general descriptions of code capability and use.

97 MATHEMATICS AND COMPUTING↗

Sierra/SolidMechanics 5.0 User's Guide Addendum for Shock Capabilities

This is an addendum to the Sierra/SolidMechanics 5.0 User’s Guide that documents additional capabilities available only in alternate versions of the Sierra/SolidMechanics (Sierra/SM) code. These alternate versions are enhanced to provide capabilities that are regulated under the U.S. Department of State’s International Traffic in Arms Regulations (ITAR) export control rules. The ITAR regulated codes are only distributed to entities that comply with the ITAR export control requirements. The ITAR enhancements to Sierra/SM include material models with an energy-dependent pressure response (appropriate for very large deformations and strain rates) and capabilities for blast modeling. This document is an addendum only; the standard Sierra/SolidMechanics 5.0 User’s Guide should be referenced for most general descriptions of code capability and use.

97 MATHEMATICS AND COMPUTING↗

Sierra/SolidMechanics 4.58 User's Guide Addendum for Shock Capabilities

This is an addendum to the Sierra/SolidMechanics 4.58 User's Guide that documents additional capabilities available only in alternate versions of the Sierra/SolidMechanics (Sierra/SM) code. These alternate versions are enhanced to provide capabilities that are regulated under the U.S. Department of State's International Traffic in Arms Regulations (ITAR) export control rules. The ITAR regulated codes are only distributed to entities that comply with the ITAR export control requirements. The ITAR enhancements to Sierra/SM include material models with an energy-dependent pressure response (appropriate for very large deformations and strain rates) and capabilities for blast modeling. This document is an addendum only; the standard Sierra/SolidMechanics 4.58 User's Guide should be referenced for most general descriptions of code capability and use.

97 MATHEMATICS AND COMPUTING↗

Sierra/SolidMechanics 5.2 User's Guide: Addendum for Shock Capabilities

This is an addendum to the Sierra/SolidMechanics 5.2 User's Guide that documents additional capabilities available only in alternate versions of the Sierra/SolidMechanics (Sierra/SM) code. These alternate versions are enhanced to provide capabilities that are regulated under the U.S. Department of State's International Traffic in Arms Regulations (ITAR) export control rules. The ITAR regulated codes are only distributed to entities that comply with the ITAR export control requirements. The ITAR enhancements to Sierra/SM include material models with an energy-dependent pressure response (appropriate for very large deformations and strain rates) and capabilities for blast modeling. This document is an addendum only; the standard Sierra/SolidMechanics 5.2 User's Guide should be referenced for most general descriptions of code capability and use.

97 MATHEMATICS AND COMPUTING↗

Sierra/SolidMechanics 5.4 User's Guide: Addendum for Shock Capabilities

This is an addendum to the Sierra/SolidMechanics 5.4 User’s Guide that documents additional capabilities available only in alternate versions of the Sierra/SolidMechanics (Sierra/SM) code. These alternate versions are enhanced to provide capabilities that are regulated under the U.S. Department of State’s International Traffic in Arms Regulations (ITAR) export control rules. The ITAR regulated codes are only distributed to entities that comply with the ITAR export control requirements. The ITAR enhancements to Sierra/SM include material models with an energy-dependent pressure response (appropriate for very large deformations and strain rates) and capabilities for blast modeling. This document is an addendum only; the standard Sierra/SolidMechanics 5.4 User’s Guide should be referenced for most general descriptions of code capability and use.

42 ENGINEERING↗

Sierra/SolidMechanics 5.6: ITAR Users' Guide, Addendum for Shock Capabilities

This is an addendum to the Sierra/SolidMechanics 5.6 User's Guide that documents additional capabilities available only in alternate versions of the Sierra/SolidMechanics (Sierra/SM) code. These alternate versions are enhanced to provide capabilities that are regulated under the U.S. Department of State's International Traffic in Arms Regulations (ITAR) export control rules. The ITAR regulated codes are only distributed to entities that comply with the ITAR export control requirements. The ITAR enhancements to Sierra/SM include material models with an energy-dependent pressure response (appropriate for very large deformations and strain rates) and capabilities for blast modeling. This document is an addendum only; the standard Sierra SolidMechanics 5.6 User's Guide should be referenced for most general descriptions of code capability and use.

97 MATHEMATICS AND COMPUTING↗

Sierra/SolidMechanics 5.8 ITAR Users' Guide

This is an addendum to the Sierra/SolidMechanics 5.8 User’s Guide that documents additional capabilities available only in alternate versions of the Sierra/SolidMechanics (Sierra/SM) code. These alternate versions are enhanced to provide capabilities that are regulated under the U.S. Department of State’s International Traffic in Arms Regulations (ITAR) export control rules. The ITAR regulated codes are only distributed to entities that comply with the ITAR export control requirements. The ITAR enhancements to Sierra/SM include material models with an energy-dependent pressure response (appropriate for very large deformations and strain rates) and capabilities for blast modeling. This document is an addendum only; the standard Sierra/SolidMechanics 5.8 User’s Guide should be referenced for most general descriptions of code capability and use.

42 ENGINEERING↗

Sierra/SolidMechanics 5.10: ITAR Users' Guide

This is an addendum to the Sierra/SolidMechanics 5.10 User’s Guide that documents additional capabilities available only in alternate versions of the Sierra/SolidMechanics (Sierra/SM) code. These alternate versions are enhanced to provide capabilities that are regulated under the U.S. Department of State’s International Traffic in Arms Regulations (ITAR) export control rules. The ITAR regulated codes are only distributed to entities that comply with the ITAR export control requirements. The ITAR enhancements to Sierra/SM include material models with an energy-dependent pressure response (appropriate for very large deformations and strain rates) and capabilities for blast modeling. This document is an addendum only; the standard Sierra/SolidMechanics 5.10 User’s Guide should be referenced for most general descriptions of code capability and use.

42 ENGINEERING↗

Generating and Sustaining Microplasma with Microwaves (Final Report)

Plasma can be generated in spaces ranging in size from astronomical down to the microscopic. The physics that describes the gas breakdown is different at each size scale. The dominant physical phenomenon also depends on the type of electromagnetic field that drives the breakdown – static, AC, RF, microwave, visible. This project, staffed by undergraduate researchers and their mentor, focused on plasma generated in the size range of 10 to 500 micrometers using microwave energy. This project was motivated by the prior observation that plasma can only be generated in microgaps when the gas is above a certain gap-dependent pressure, here called the transition pressure. A microwave-driven microgap was designed and constructed in this project and then used to measure the electric field required to initiate plasma over a wide range of pressures from 0.1 Torr to 760 Torr (1 atmosphere).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗