Plastic behavior of some composite materials
Two phase fiber reinforced composites under polyaxial stresses, predicting plastic behavior by deformation theory
Huang, W.-C.↗
SEARCH · Engineering Papers
Results for “PLASTICS”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
On the postbuckling behavior of imperfection- sensitive structures in the plastic range
Axisymmetric plastic deformation of imperfection sensitive spherical shell after elastic buckling, considering load carrying capacity
Hutchinson, J. W.↗
Use of thin plastic films at cryogenic temperatures
Commercially available plastic film materials that remain flexible at cryogenic temperatures and resist failures caused by folds and wrinkles created during expulsion were investigated for use in expulsion bladders for liquefied gases. Compatible adhesive systems, fabrication techniques, and results of impact and dynamic loading tests are summarized.
Lark, R. F.↗
Built-in bleeder system in laminated plastic structures
Method is described for interplying resin absorbing, glass bleeder cloth with the layup for fabricating laminated nonflammable plastic structures with wrinkle-free surfaces.
Aguilar, A. G.↗
Plastic set of smooth large radii of curvature thermal conductance specimens at light loads
Thermal contact conductance test data at high vacuum were obtained from two Armco iron specimens having smooth, large radii of curvature, convex, one-half wave length surfaces. The data are compared with calculations based on two macroscopic elastic deformation theories and an empirical expression. Major disagreement with the theories and fair agreement with the empirical expression resulted. Plastic deformation of all the contacting surfaces was verified from surface analyzer statistics. These results indicate that the theoretical assumption of macroscopic elastic deformation is inadequate for accurate prediction of heat transfer with light loads for Armco iron specimens similar to those used in this investigation.
Mckinzie, D. J., Jr.↗
High Z particle Apollo astronaut dosimetry with plastics
On Apollo missions, the individual astronauts' high Z particle exposure is measured by means of Lexan polycarbonate plastic. These layers form one component of the passive dosimetry packets worn in the constant wear garment. They serve as threshold type, high Z, charged particle track detectors, recording only the very highly ionizing particles. The detectors yield information on the particles' charge, energy, and direction of travel. This data, in turn, is used to obtain the track fluence, the stopping particle density as an integral Z distribution, and the particles' integral LET spectrum. Some of the data gathered on Apollo missions 8-13 is presented.
Benton, E. V.↗
Investigation of hazards associated with plastic bonded starter mix manufacturing processes
An investigation to determine the hazards potential evaluation of plastic bonded starter mix (PBSM) production processes and the application to the M18 and M7A3 grenades is reported. The investigation indicated: (1) the materials with the greatest hazards characteristics, (2) process operating stations most likely to initiate hazardous conditions, (3) the test program required to examine ignition characteristics and process hazards, and (4) the method of handling the accumulated information from testing and safety analyses.
Source record↗
Comparison of NASTRAN and STARDYNE static analysis of a graphite fiber reinforced plastic truss structure
A static and buckling analysis of the ATS-F&G spacecraft reflector support truss (RST) and bridge truss assembly using NASTRAN was conducted. The RST is fabricated from a new material, graphite fiber reinforced plastic. A comparison is made with the NASTRAN results and the results of a similar analysis conducted using the stardyne program. The results of an actual static load test are also compared.
Honeycutt, G. H.↗
Computer program: Jet 3 to calculate the large elastic plastic dynamically induced deformations of free and restrained, partial and/or complete structural rings
A user-oriented FORTRAN 4 computer program, called JET 3, is presented. The JET 3 program, which employs the spatial finite-element and timewise finite-difference method, can be used to predict the large two-dimensional elastic-plastic transient Kirchhoff-type deformations of a complete or partial structural ring, with various support conditions and restraints, subjected to a variety of initial velocity distributions and externally-applied transient forcing functions. The geometric shapes of the structural ring can be circular or arbitrarily curved and with variable thickness. Strain-hardening and strain-rate effects of the material are taken into account.
Wu, R. W.↗
Elasto-plastic analysis of a mode I edge crack with application to a surface notch.
A finite element analysis has been undertaken of the mechanical state of a plate containing a crack subjected to mode I loading. Specifically, a localized, well-defined surface depression (dimple) previously observed on the back surface of plate specimens immediately behind the plane of the crack was examined. The approach taken is concerned with defining more precisely the dimpling behavior as a function of relative flaw depth and applied stress level, as well as the development of the plastic zone at the crack tip.
Francis, P. H.↗
Plastic set of smooth large radii of curvature thermal conductance specimens at light loads.
Thermal contact conductance test data at high vacuum were obtained from two Armco iron specimens having smooth, large radii of curvature, convex, one-half wave length surfaces. The data are compared with calculations based on two macroscopic elastic deformation theories and an empirical expression. Major disagreement with the theories and fair agreement with the empirical expression resulted. Plastic deformation of all the contacting surfaces was verified from surface analyzer statistics. These results indicate that the theoretical assumption of macroscopic elastic deformation is inadequate for accurate prediction of heat transfer with light loads for Armco iron specimens similar to those used in this investigation.
Mckinzie, D. J., Jr.↗
Elasto-plastic bending of cracked plates, including the effects of crack closure
A capability for solving elasto-plastic plate bending problems is developed using assumptions consistent with Kirchhoff plate theory. Both bending and extensional modes of deformation are admitted with the two modes becoming coupled as yielding proceeds. Equilibrium solutions are obtained numerically by determination of the stationary point of a functional which is analogous to the potential strain energy. The stationary value of the functional for each load increment is efficiently obtained through use of the conjugate gradient. This technique is applied to the problem of a large centrally through cracked plate subject to remote circular bending. Comparison is drawn between two cases of the bending problem. The first neglects the possibility of crack face interference with bending, and the second includes a kinematic prohibition against the crack face from passing through the symmetry plane. Results are reported which isolate the effects of elastoplastic flow and crack closure.
Jones, D. P.↗
An investigation of plastic fracture in aluminum alloys
The brittle fracture of many high strength alloys such as steel, titanium, and aluminum was shown to occur by a process called plastic fracture. According to this process microscopic voids form at impurity particles, then grow and coalesce to cause the final rupture. To further understand the role of impurities, four aluminum alloys were investigated: 2024-T851, 2124-T851, 7075-T7351 and 7079-T651. Fractography, quantitative metallography, and microprobe studies assessed the roles of various impurity particles relative to these alloys.
Low, J. R., Jr.↗
Investigation of the plastic fracture of high strength steels
An investigation of the plastic fracture process to improve tensile strength in high strength steels is presented. Two generic types of steels are considered: a quenched and tempered grade and a maraging grade, in order to compare two different matrix microstructures. Each type of steel was studied in commercial grade purity and in special melted high purity form, low in residual and impurity elements. The specific alloys dealt with include AISI 4340 and 18 Ni, 200 grade maraging steel, both heat treated to the same yield strength level of approximately 200 ksi.
Cox, T. B.↗
Role of plastic deformation in wear of copper and copper - 10-percent-aluminum alloy in cryogenic fuels
High-purity copper specimens and a copper-aluminum (10%) alloy specimen were subjected to sliding against Type 440 C in cryogenic fuel environments. It was found that virtually all wear occurred by the plastic deformation of a recrystallized layer extending to about 10 micrometers below the wear scar surface of the copper or copper alloy. The wear debris was in the form of a layered structure adhering to the exit region of the wear scar. Measurements on the high purity copper specimens indicated that the wear rate was proportional to the applied load and to the sliding velocity squared. A physical model of the wear process is proposed to account for these observations.
Bill, R. C.↗
Large deflection elastic-plastic dynamic response of stiffened shells of revolution
The formulation and check out porblems for a computer code DYNAPLAS, which analyzes the large deflection elastic-plastic dynamic response of stiffened shells of revolution, are presented. The formulation for special discretization is by the finite element method with finite differences being used for the evaluation of the pseudo forces due to material and geometric nonlinearities. Time integration is by the Houbolt method. The stiffeners may be due to concentrated or distributed eccentric rings and spring supports at arbitrary angles around the circumference of the elements. Check out porblems include the comparison of solutions from DYNAPLAS with experimental and other computer solutions for rings, conical and cylindrical shells and a curved panel. A hypothetical submarine including stiffeners and missile tube is studied under a combination of hydrostatic and dynamically applied asymmetrical pressure loadings.
Stricklin, J. A.↗
Experimental stress analysis of large plastic deformations in a hollow sphere deformed by impact against a concrete block
An experimental plastic strain measurement system is presented for use on the surface of high velocity impact test models. The system was used on a hollow sphere tested in impact against a reinforced concrete block. True strains, deviatoric stresses, and true stresses were calculated from experimental measurements. The maximum strain measured in the model was small compared to the true failure strain obtained from static tensile tests of model material. This fact suggests that a much greater impact velocity would be required to cause failure of the model shell structure.
Morris, R. E.↗
Apparatus for heat treating plastic belts
Apparatus performs programed rotating, stretching/shrinking and heat treatment necessary to fabrication of high-performance plastic belts. Belts can be treated in lengths varying from 7 to 48 in., in widths up to 1 in., and in thicknesses up to approximately 0.003 in.
Topits, A., Jr.↗