Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Mass Spectrometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Characterization of n-Type Iodine-Doped and Indium-Doped CdTe/Cd-Se-Te Thin Films Fabricated by Close-Spaced Sublimation Epitaxy

In this study, n-type CdTe thin films, specifically iodine-doped CdTe (CdTe:I), indium-doped CdTe (CdTe:In), and indium-doped Cd-Se-Te (CST:In), were synthesized using close-spaced sublimation epitaxy (CSSE). Characterization techniques secondary ion mass spectrometry (SIMS), electron backscatter diffraction (EBSD), Hall-effect measurements, and time-resolved photoluminescence (TRPL) were employed to analyze the chemical, structural, and electronic properties of these materials. The results indicated epitaxial single crystal CSSE films grew on the single crystal substrates, with carrier density ranging from 10^14 - 10^16 cm -3 , and after post-annealing, the minority-carrier lifetimes reach near the radiative limit. Additionally, a preliminary exploration of homojunction structures with an n- type (CdTe:In /CST:In /CdTe:I) /CdTe:P /Cu /Mo configuration was performed. The best device performance was achieved with CdTe:I including CdS aiding in band alignment, resulting in a power conversion efficiency (..eta..) of 2.61% with open circuit voltage (Voc) of 850 mV, fill factor (FF) of 47.8%, and short-circuit current (Jsc) of 6.44 mA/cm 2 . The observed low Jsc and efficiency may be attributed to a buried junction and a poor interface, due to dopant interdiffusion. Consequently, further investigations focusing on interface optimization, diffusion blocking, and reduced recombination through passivation, are crucial to enhancing the efficiency of CSSE CdTe homojunction devices in the future.

cadmium compounds↗
DOE OSTI2021

Growth differentiation factor-15 promotes immune escape of ovarian cancer via targeting CD44 in dendritic cells

Immune escape is the main cause of the low response rate to immunotherapy for cancer, including ovarian cancer. Growth differentiation factor-15 (GDF-15) inhibits immune cell function. However, only few reports described the mechanism. Therefore, the aim of this study was to investigate the mechanism of immune escape regulated by GDF-15 in ovarian cancer. Ovarian cancer patients and healthy women were enrolled in this study. Immunohistochemistry and ELISA were performed to measure GDF-15 expression. Immunoprecipitation combined with mass spectrometry, surface plasmon resonance, and co-immunoprecipitation assay were used to evaluate the interaction between GDF-15 and the surface molecules of DCs. Immunofluorescence analysis, flow cytometry and transwell assay were used to evaluate additional effects of GDF-15 on DCs. The results showed that GDF-15 expression was higher in the ovarian cancer patients compared to that in the healthy women. The TIMER algorithm revealed that highly GDF-15 expression is associated with immune DC infiltration in immunoreactive high-grade serous carcinoma. A further study showed that GDF-15 suppressed DCs maturation, as well as IL-12p40 and TNF-α secretion, the length and number of protrusions and the migration. More importantly, CD44 in the surface of DCs interacted with GDF-15. The overexpression of CD44 in DCs resulted in the suppression of the inhibitory effect of GDF-15 on the length and number of DC synapses. In DCs overexpressing CD44 the inhibition of GDF-15 on the expression of CD11c, CD83 and CD86 was decreased, while in DCs with a knockdown of CD44 the inhibition was further enhanced. Knockdown of CD44 in DCs enhanced the inhibitory effect of GDF-15 on DC migration, while the overexpression of CD44 inhibited the inhibitory effect of GDF-15 on DC migration. In conclusion, the present study suggested that GDF-15 might facilitate ovarian cancer immune escape by interacting with CD44 in DCs to inhibit their function.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Robust surfactant-assisted one-pot sample preparation for label-free single-cell and nanoscale proteomics

With advanced mass spectrometry (MS)-based proteomics, genome-scale proteome coverage can be achieved from bulk cells. However, such bulk measurement obscures cell to cell heterogeneity, precluding proteome profiling of single cells and small numbers of cells of interest. To address this issue, in recent 5 years there are a surge of small sample preparation methods developed for robust effective collection and processing of single cells and small numbers of cells for in-depth MS-based proteome profiling. Based on their broad accessibility, they can be categorized into two types: specific device- and standard PCR tube- or multi-well plate-based methods. Herein we describe the detailed protocol of our recently developed, easily adoptable, Surfactant-assisted One-Pot (SOP) sample preparation coupled with MS method termed SOP-MS for label-free single-cell and nanoscale proteomics. SOP-MS capitalizes on the combination of a MS-compatible surfactant, DDM (n-Dodecyl-ß-D-maltoside), and standard low-bind PCR tube or multi-well plate for ‘all-in-one’ one-pot sample preparation without sample transfer. With its robust and convenient features, SOP-MS can be readily implemented in any MS laboratory for single-cell and nanoscale proteomics. With further improvements in MS detection sensitivity and sample throughput, we believe that SOP-MS could open an avenue for single-cell proteomics with broad applicability in the biological and biomedical research.

Single-cell proteomics, nanoscale proteomics, SOP-↗
DOE OSTI2021

An Introduction to the Benchmarking and Publications for Non-Targeted Analysis Working Group

Non-targeted analysis (NTA) encompasses a rapidly evolving set of mass spectrometry techniques aimed at characterizing the chemical composition of complex samples, identifying unknown compounds, and/or classifying samples, without prior knowledge regarding the chemical content of the samples. Recent advances in NTA are the result of improved and more accessible instrumentation for data generation, and analysis tools for data evaluation and interpretation. As researchers continue to develop NTA approaches in various scientific fields, there is a growing need to identify, disseminate, and adopt community-wide method reporting guidelines. In 2018, NTA researchers formed the Benchmarking and Publications for Non-Targeted Analysis Working Group (BP4NTA) to address this need. Consisting of participants from around the world and representing fields ranging from environmental science and food chemistry to ‘omics and toxicology, BP4NTA provides resources addressing a variety of challenges associated with NTA. Furthermore, thus far, BP4NTA group members have aimed to establish consensus on NTA-related terms and concepts, and to create consistency in reporting practices by providing resources on a public website, including consensus definitions, reference content, and lists of available tools. Moving forward, BP4NTA will provide a setting for NTA researchers to continue discussing emerging challenges and contribute to additional harmonization efforts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Carrier-assisted One-pot Sample Preparation for Targeted Proteomics Analysis of Small Numbers of Human Cells

Protein analysis of small numbers of human cells is primarily achieved by targeted proteomics with antibody-based immunoassays, which have inherent limitations (e.g., low multiplex and unavailability of antibodies for new proteins). Mass spectrometry (MS)-based targeted proteomics has emerged as an alternative because it is antibody-free, high multiplex, and has high specificity and quantitation accuracy. Recent advances in MS instrumentation make MS-based targeted proteomics possible for multiplexed quantification of highly abundant proteins in single cells. However, there is a technical challenge for effective processing of single cells with minimal sample loss for MS analysis. To address this issue, we have recently developed a convenient protein carrier-assisted one-pot sample preparation coupled with liquid chromatography (LC) - selected reaction monitoring (SRM) termed cLC-SRM for targeted proteomics analysis of small numbers of human cells. This method capitalizes on using the combined excessive exogenous protein as a carrier and low-volume one-pot processing to greatly reduce surface adsorption losses as well as high-specificity LC-SRM to effectively address the increased dynamic concentration range due to the addition of exogeneous carrier protein. Its utility has been demonstrated by accurate quantification of most moderately abundant proteins in small numbers of cells (e.g., 10-100 cells) and highly abundant proteins in single cells. The easy-to-implement features and no need for specific devices make this method readily accessible to most proteomics laboratories. In this study, we have provided a detailed protocol for cLC-SRM analysis of small numbers of human cells including cell sorting, cell lysis and digestion, LC-SRM analysis, and data analysis. Further improvements in detection sensitivity and sample throughput are needed towards targeted single-cell proteomics analysis. We anticipate that cLC-SRM will be broadly applied to biomedical research and systems biology with the potential of facilitating precision medicine.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2023

An Extremely Stable, Highly Soluble Monosubstituted Anthraquinone for Aqueous Redox Flow Batteries

An extremely stable, energy-dense (53.6 Ah L –1 , 2 M transferrable electrons), low crossover (permeability of <1 × 10 –13 cm 2 s –1 using Nafion 212 (Nafion is a trademark polymer from DuPont)), and potentially inexpensive anthraquinone with 2-2-propionate ether anthraquinone structure (abbreviated 2-2PEAQ) is synthesized and extensively evaluated under practically relevant conditions for use in the negolyte of an aqueous redox flow battery. 2-2PEAQ shows a high stability with a fade rate of 0.03–0.05% per day at different applied current densities, cut-off voltage windows, and concentrations (0.1 and 1.0 M ) in both a full cell paired with a ferro/ferricyanide posolyte as well as a symmetric cell. 2-2PEAQ is further shown to have extreme long-term stability, losing only ≈0.01% per day when an electrochemical rejuvenation strategy is employed. From post-mortem analysis (nuclear magnetic resonance (NMR), liquid chromatography–mass spectrometry (LC-MS), and cyclic voltammetry (CV)) two degradation mechanisms are deduced: side chain loss and anthrone formation. 2-2PEAQ with the ether linkages attached on carbons non-adjacent to the central ring is found to have three times lower fade rate compared to its isomer with ether linkages on the carbon adjacent to the central quinone ring. Here, the present study introduces a viable negolyte candidate for grid-scale aqueous organic redox flow batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

Structure, Function, and Application of Self–Healing Adhesives from Mistletoe Viscin

Berries from the European Mistletoe (Viscum album) possess a sticky tissue called viscin that facilitates adhesion and germination onto host trees. Recent studies of viscin have demonstrated its adhesive capacity on a range of natural and synthetic surfaces including wood, skin, metals, and plastic. Yet, the underlying mechanisms remain poorly understood. Here, an investigation of the adhesive performance of mistletoe viscin is performed, demonstrating its hygroscopic nature and ability to self-heal following adhesive failure. It is identified that adhesion originates from a water-soluble adhesive component that can be extracted, isolated, and characterized independently. Lap shear mechanical testing indicates that the mistletoe adhesive extract (MAE) outperforms native viscin tissue, as well as gum arabic and arabinogalactan—common plant-based adhesives. Furthermore, humidity uptake experiments reveal that MAE can reversibly absorb nearly 100% of its mass in water from the atmosphere. In-depth spectroscopic and mass spectrometry investigations reveal a composition consisting primarily of an atypical arabinogalactan, with additional sugar alcohols. Finally, several proof-of-concept applications are demonstrated using MAE for hygro-responsive reversible adhesion between various surfaces including skin, plastic, PDMS, and paper, revealing that MAE holds potential as a biorenewable and reusable adhesive for applications in cosmetics, packaging, and potentially, tissue engineering.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Enhanced Optical Contrast and Switching in Near‐Infrared Electrochromic Devices by Optimizing Conjugated Polymer Oligo(Ethylene Glycol) Sidechain Content and Gel Electrolyte Composition

Abstract A detailed investigation addressing the effects of functionalizing conjugated polymers with oligo(ethylene glycol) (EG n ) sidechains on the performance and polymer‐electrolyte compatibility of electrochromic devices (ECDs) is reported. The electrochemistry for a series of donor‐acceptor copolymers having near‐infrared (NIR)‐optical absorption, where the donor fragment is 3,4‐ethylenedioxythiophene (EDOT) or an EG n functionalized bithiophene (g2T) and the acceptor fragment is diketopyrrolopyrrole (DPP) functionalized with branched alkyl or EG n sidechains, is extensively probed. ECDs are next fabricated and it is found that EG n sidechain incorporation must be finely balanced to promote polymer‐electrolyte compatibility and provide efficient ion exchange. Proper electrolyte‐cation pairing and polymer structural tuning affords a 2x increase in optical contrast (from 12% to 24%) and >60x reduction in switching time (from 20 to 0.3 s). Atomic force microscopy (AFM)/grazing incidence wide‐angle X‐ray scattering (GIWAXS) characterization of the polymer film morphology/microstructure reveals that an over‐abundance of EG n sidechains generates large polymer crystallites, which can suppress ion exchange. Lastly, time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) indicates sidechain/electrolyte identity does not influence the electrolyte penetration depth into the films, and EG n sidechain inclusion increases electrolyte cation uptake. The material structural design insight and guidelines regarding the polymer‐electrolyte ion insertion/expulsion dynamics reported here should be of significant utility for developing next‐generation mixed ionic‐electronic conducting materials.

Chemistry↗
DOE OSTI2024

Formation and Microwave Losses of Hydrides in Superconducting Niobium Thin Films Resulting from Fluoride Chemical Processing

Abstract Superconducting niobium (Nb) thin films have recently attracted significant attention due to their utility for quantum information technologies. In the processing of Nb thin films, fluoride‐based chemical etchants are commonly used to remove surface oxides that are known to affect superconducting quantum devices adversely. However, these same etchants can also introduce hydrogen to form Nb hydrides, potentially negatively impacting microwave loss performance. Here, comprehensive materials characterization of Nb hydrides formed in Nb thin films as a function of fluoride chemical treatments is presented. In particular, secondary‐ion mass spectrometry, X‐ray scattering, and transmission electron microscopy reveal the spatial distribution and phase transformation of Nb hydrides. The rate of hydride formation is determined by the fluoride solution acidity and the etch rate of Nb 2 O 5, which acts as a diffusion barrier for hydrogen into Nb. The resulting Nb hydrides are detrimental to Nb superconducting properties and lead to increased power‐independent microwave loss in coplanar waveguide resonators. However, Nb hydrides do not correlate with two‐level system loss or device aging mechanisms. Overall, this work provides insight into the formation of Nb hydrides and their role in microwave loss, thus guiding ongoing efforts to maximize coherence time in superconducting quantum devices.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Crossover Effects of Transition‐Metal Ions on Lithium‐Metal Anode in Localized High Concentration Electrolytes

Abstract The stability of the solid–electrolyte interphase (SEI) is critical to the cycle life of lithium‐metal batteries (LMBs). While the crossover effect of transition‐metal ions from cathode to anode is extensively studied in lithium‐ion batteries with graphite anodes, its impact on LMBs remains largely unexplored. Herein, this study investigates the electrochemical and chemical properties of SEI layers formed on lithium‐metal anodes in localized high‐concentration electrolytes (LHCEs) containing dissolved transition‐metal ions (Ni 2+ , Mn 2+ , and Co 2+ ). It is demonstrated that transition‐metal ions in LHCEs reduce the coulombic efficiency (CE) and significantly degrade the cycle life of LMBs. Time‐of‐flight secondary‐ion mass spectrometry (ToF‐SIMS) reveals that SEI structures differ depending on the dissolved TM ion, with Mn 2+ and Co 2+ inducing severe destabilization, and Ni 2+ exhibiting a less severe impact. These findings underscore the detrimental effects of transition‐metal crossover effects in LMB systems.

Guo, Zezhou [Materials Science and Engineering Pro↗
DOE OSTI2020

The Role of Demixing and Crystallization Kinetics on the Stability of Non‐Fullerene Organic Solar Cells

Abstract With power conversion efficiency now over 17%, a long operational lifetime is essential for the successful application of organic solar cells. However, most non‐fullerene acceptors can crystallize and destroy devices, yet the fundamental underlying thermodynamic and kinetic aspects of acceptor crystallization have received limited attention. Here, room‐temperature (RT) diffusion coefficients of 3.4 × 10 −23 and 2.0 × 10 −22 are measured for ITIC‐2Cl and ITIC‐2F, two state‐of‐the‐art non‐fullerene acceptors. The low coefficients are enough to provide for kinetic stabilization of the morphology against demixing at RT. Additionally profound differences in crystallization characteristics are discovered between ITIC‐2F and ITIC‐2Cl. The differences as observed by secondary‐ion mass spectrometry, differential scanning calorimetry (DSC), grazing‐incidence wide‐angle X‐ray scattering, and microscopy can be related directly to device degradation and are attributed to the significantly different nucleation and growth rates, with a difference in the growth rate of a factor of 12 at RT. ITIC‐4F and ITIC‐4Cl exhibit similar characteristics. The results reveal the importance of diffusion coefficients and melting enthalpies in controlling the growth rates, and that differences in halogenation can drastically change crystallization kinetics and device stability. It is furthermore delineated how low nucleation density and large growth rates can be inferred from DSC and microscopy experiments which could be used to guide molecular design for stability.

Hu, Huawei↗
DOE OSTI2023

Solid‐State Reaction Heterogeneity During Calcination of Lithium‐Ion Battery Cathode

Abstract During solid‐state calcination, with increasing temperature, materials undergo complex phase transitions with heterogeneous solid‐state reactions and mass transport. Precise control of the calcination chemistry is therefore crucial for synthesizing state‐of‐the‐art Ni‐rich layered oxides (LiNi 1‐x‐y Co x Mn y O 2 , NRNCM) as cathode materials for lithium‐ion batteries. Although the battery performance depends on the chemical heterogeneity during NRNCM calcination, it has not yet been elucidated. Herein, through synchrotron‐based X‐ray, mass spectrometry microscopy, and structural analyses, it is revealed that the temperature‐dependent reaction kinetics, the diffusivity of solid‐state lithium sources, and the ambient oxygen control the local chemical compositions of the reaction intermediates within a calcined particle. Additionally, it is found that the variations in the reducing power of the transition metals (i.e., Ni, Co, and Mn) determine the local structures at the nanoscale. The investigation of the reaction mechanism via imaging analysis provides valuable information for tuning the calcination chemistry and developing high‐energy/power density lithium‐ion batteries.

Chemistry↗
DOE OSTI2023

Revealing the Anion–Solvent Interaction for Ultralow Temperature Lithium Metal Batteries

Anion solvation in electrolytes can largely change the electrochemical performance of the electrolytes, yet has been rarely investigated. Herein, three anions of bis(trifluoromethanesulfonyl)imide (TFSI), bis(fluorosulfonyl)imide (FSI), and derived asymmetric (fluorosulfonyl)(trifluoro-methanesulfonyl)imide (FTFSI) are systematically examined in a weakly Li + cation solvating solvent of bis(3-fluoropropyl)ether (BFPE). In-situ liquid secondary ion mass spectrometry demonstrates that FTFSI - and FSI - anions are associated with BFPE solvent, while weak TFSI - /BFPE cluster signals are detected. Molecular modeling further reveals that the anion–solvent interaction is accompanied by the formation of H-bonding-like interactions. Further, anion solvation enhances the Li + cation transfer number and reduces the organic component in solid electrolyte interphase, which enhances the Li plating/stripping Coulombic efficiency at a low temperature of -30 °C from 42.4% in TFSI-based electrolytes to 98.7% in 1.5 m LiFTFSI and 97.9% in LiFSI-BFPE electrolytes. The anion–solvent interactions, especially asymmetric anion solvation also accelerate the Li + desolvation kinetics. The 1.5 m LiFTFSI-BFPE electrolyte with strong anion–solvent interaction enables LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811)||Li (20 µm) full cell with stable cyclability even under -40 °C, retaining over 92% of initial capacity (115 mAh g -1 , after 100 cycles). The anion–solvent interactions insights allow to rational design the electrolyte for lithium metal batteries and beyond to achieve high performance.

25 ENERGY STORAGE↗
DOE OSTI2024

Formation and Detriments of Residual Alkaline Compounds on High-Nickel Layered Oxide Cathodes

High-nickel layered oxides LiNi x M 1-x O 2 (x ≥ 0.9) have emerged as promising cathode materials for automotive batteries due to their high energy density and lower cost. However, the formation and accumulation of surface alkaline compounds during storage hinder their mass production and commercialization. Here, in this study, a validated chemical method is employed to deconvolute and quantify the evolution of each residual lithium compound in four representative cathodes during ambient-air storage, viz., LiNiO 2 (LNO), LiNi 0.95 Co 0.05 O 2 (NC), LiNi 0.95 Mn 0.05 O 2 (NM), and LiNi 0.95 Al 0.05 O 2 (NA). Furthermore, the activation energy of the reaction between water and the cathode is determined by measuring the leached LiOH concentration at various temperatures. While residual lithium and time-of-flight secondary-ion mass spectrometry measurements collectively reveal that the air stability overall follows the trend of NM > NA ≈ NC > LNO, the aged NM exhibits the highest charge-transfer resistance and the worst electrochemical performance among the cathodes. In situ, X-ray diffraction and scanning transmission electron microscopy unveil that the aged NM is plagued by a large area of resistive spinel-like M 3–x Li x O 4 phases, leading to aggravated particle reaction heterogeneity. Finally, a one-step recalcination method is demonstrated effective in fully restoring the degraded cathodes. This work provides insights into overcoming air sensitivity issues of high-Ni cathodes.

(S)TEM↗
DOE OSTI2025

Understanding the Role of Borohydride Doping in Electrochemical Stability of Argyrodite Li 6 PS 5 Cl Solid‐State Electrolyte

This work elucidates the mechanism by which lithium borohydride (LiBH 4 ) doping into argyrodite-type Li 6 PS 5 Cl (LBH-LPSCl) solid-state electrolyte (SSE) enhances electrochemical stability. State-of-the-art electrochemical performance is achieved with 5 wt% borohydride. Symmetric cells achieve critical current density (CCD) of 7.3 mA cm −2 , versus 2.6 mA cm −2 for baseline-LPSCl. All solid-state batteries (ASSBs) employing lithium metal and NMC811 cathode are stable over 400 cycles at 0.5C, with capacity retention of 83%. An anode-free ASSB (AF-ASSB) is stable over 600 cycles, with capacity loss of 0.04% per cycle. 5LBH-LPSCl allows for enhanced low temperature operation, down to −14 °C. Yet the difference in electrolytes’ bulk microstructures and hardnesses are minimal, while ionic conductivity is incrementally improved (≈50%). Theoretical modeling indicates limited effect of substitution on thermodynamic stability of PS 4 3- units, which decompose when contacting Li. Instead, enhanced electrochemical stability is site-specific kinetic effect: In situ electrodeposition experiments using X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (TOF-SIMS) reveal tri-layer SEI based predominately on Li 3 P/LiBH 4 /Li 2 S that blocks electrons while facilitating ion transport. This SEI manifests reduced interface resistance and accelerated nucleation and growth of metallic Li. With baseline-LPSCl the SEI based on Li 3 P/Li 2 S is substantially thicker, generating localized stresses that promote interfacial cracking while cycling.

argyrodite↗
DOE OSTI2026

Impact of Anode to Cathode Crossover in Lithium‐metal Batteries With High‐Nickel Cathodes

The advancement of high-energy-density lithium-metal batteries (LMBs) is hindered by the chemical instability of both lithium-metal anode and high-nickel layered oxide cathodes. While cathode-to-anode crossover is well-documented, the reverse process of anode-to-cathode crossover remains underexplored. Here, we systematically investigate such crossovers and the degradation pathway in pouch cells with a localized high-concentration electrolyte, comparing NMC622, NMC811, and NMC90 cathodes paired with lithium-metal and graphite anodes. Despite delivering higher initial capacities, LMBs exhibit faster capacity fade under long-term cycling at 45 °C. To isolate cathode-side degradation, galvanostatic electrochemical impedance spectroscopy (GEIS) measurements of cycled cathodes paired with delithiated lithium iron phosphate (LFP) counter electrodes reveal significantly higher charge-transfer resistance in cathodes cycled with lithium-metal. Surface characterization via X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) reveals greater electrolyte decomposition on cathodes cycled with lithium metal, leading to thicker, more organic-rich cathode–electrolyte interphases (CEIs), consistent with the elevated charge-transfer resistance observed in GEIS measurements. Notably, NMC90 shows the most pronounced CEI thickening, linking higher cathode surface reactivity to greater susceptibility to anode-to-cathode crossover. This work presents compelling evidence of crosstalk degradation originating from lithium-metal anodes and underscores the importance of cross-interface stability for the design of durable LMBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Revealing the Structural Evolution of Green Rust Synthesized in Ionic Liquids by In Situ Molecular Imaging

Abstract Ionic liquids are green solvents that have wide applications in material synthesis, catalysis, and separation. A model switchable ionic liquid (SWIL) consisting of 1,8‐diazabicycloundec‐7‐ene (DBU) and 1‐hexanol with carbon dioxide (CO 2 ) as the trigger gas is chosen to synthesize nanocrystalline green rust. Under anoxic conditions, by adding iron (II) acetate (Fe(C 2 H 3 O 2 ) 2 ) and methanol to the degassed SWIL, a nanoparticulate green rust with carbonate (nano‐GR) is synthesized. More importantly, the molecular structural change of the ionic liquid resulting in green rust crystallines is first characterized using in situ liquid using time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS) coupled with the system for analysis at the liquid vacuum interface (SALVI), a vacuum compatible microfluidic reactor in this work. Dimers and ionic clusters consisting ferric and ferrous ions are identified in liquid ToF‐SIMS spectra. Spectral principal component analysis is used to confirm that these ion pairs including dimers and cluster ions are different from nonionic liquids. The results show that liquid ToF‐SIMS can be a useful tool to study complex liquids at the molecular level providing insights into predicative synthesis of nanomaterials using environmentally friendly green solvents and giving unique visualization of the evolving material interface due to nucleation.

Shen, Yanjie↗
DOE OSTI2025

CO 2 in Ionene–Ionic Liquid Composite Membranes

Abstract Ionene – ionic liquid (IL) composites are promising materials for CO 2 separation, yet a molecular‐level understanding of their structure and its impact on CO 2 speciation, solubility, rotation, and diffusivity remains unclear. Herein, using multimodal nuclear magnetic resonance (NMR), time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS), atomic force microscopy (AFM), and molecular dynamics (MD) simulations, we reveal that the composites contain IL‐rich domains extending across hundreds of nanometres within the ionene matrix, and these bicontinuous domains span the entire membrane depth. CO 2 also absorbs into the ionene matrix, with the distribution between two CO 2 species varying with temperature and time. The rotational correlation times of these two species are on the timescale of 0.1 and 1 ns, respectively. As IL content increases, the ionic domains expand, resulting in higher CO 2 solubility due to enhanced molecular dynamics and increased free volume in both ionene backbones and IL‐rich regions. Although CO 2 diffusion in the membranes is an order of magnitude slower than in bulk IL, the activation energy for CO 2 diffusion remains comparable. Ionene‐IL composites represent a promising platform for designing CO 2 separation membranes, offering enhanced CO 2 diffusion and selectivity through IL‐rich domains, and increased CO 2 solubility and mechanical integrity from the ionene matrix.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗