Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Lasers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Preliminary comparison of laser and solar space power systems

Four laser receiver systems are compared to onboard solar photovoltaic power generation for spacecraft electrical requirements. The laser photovoltaic and laser MHD receivers were found to be lighter than a comparable planar solar photovoltaic system. The laser receiver also shows less drag at lower altitudes. Panel area is also reduced for the laser receiver allowing fewer Shuttle trips for construction. Finally, it is shown that a 1 megawatt laser and receiver system might be constructed with less weight than a comparable planar solar photovoltaic system.

Deyoung, R. J.↗
NASA NTRS1983

Photovoltaic conversion of laser to electrical power

Transmission of power in space using lasers will require devices for converting the laser power to electrical power. One such type of device for accomplishing this is the photovoltaic converter. This paper reviews photovoltaic converters and their application for conversion of monochromatic laser power to electrical power. Laser power densities greater than 1000 W/sq cm are considered. For a converter operated at 300 K a lower bandgap limit of 0.67 eV (1.80 micron) is defined. For ideal conditions, an efficiency of 47.8 percent is calculated for Nd/Liquid laser radiation incident on an Si converter. Several types of photovoltaic converters are discussed. Series resistance is identified as a major problem. Vertical multijunction converters are the most promising photovoltaic devices for use as laser to electric power converters.

Walker, G. H.↗
NASA NTRS1984

Calibration of diode laser spectra using a confocal etalon

The dual-beam diode laser spectrometer described by Jennings (1980) is adapted to use a 50-cm confocal etalon for frequency calibration. The collimated radiation from the laser is split at a wedged ZnSe window, and the reference beam is then focused at the midpoint of the etalon length. After the etalon, the reference beam is recollimated and continues its regular path to the monochromator and detectors. An aperture is placed before the etalon in order to limit the entrance beam diameter to approximately 5 mm. Both ends of the etalon are furnished with two-axis adjustments. Initial alignment is achieved using an He-Ne laser, and final optimization involves adjustment of the cavity length as well as the etalon pitch and yaw. The 50-cm confocal etalon produces fringes separated by 150 MHz (0.005/cm). With the aid of a CO2 laser, it is found to have fringe widths (FWHM) of 2 MHz. The confocal etalon makes it possible to improve the accuracy of relative frequency measurements in diode laser spectra and to check the spectral purity and stability of the laser during the recording of spectra.

Jennings, D. E.↗
NASA NTRS1984

Laser propulsion

An introduction to thermal laser propulsion is presented. This form of rocket propulsion uses a laser beam from a remotely-located laser to heat a propellant gas, which is then expanded in a conventional way to produce thrust. This propulsion scheme has the potential for producing high specific impulse (greater than 1000 s) at moderate to high thrust (1000 lbs). Laser propulsion can thus fill a niche in propulsion for spaceflight missions which can be filled by no other practical scheme. The system analyses and some of the experimental and theoretical studies which have been performed are briefly reviewed. Production of thrust by a pulsed laser has been demonstrated on a laboratory scale at an Isp of 1000 s in hydrogen. While more work is needed, it seems apparent that laser propulsion has an important and unique capability which should be pursued, and should be considered for space missions in the 1990's and beyond.

Kemp, N. H.↗
NASA NTRS1984

Stability of absorption phenomena in laser-thermal propulsion

The mean flow and stability characteristics of laser absorption phenomena in a choked converging-diverging nozzle are considered. Calculations are presented for a given nozzle geometry and a series of laser intensities. Gas absorptivities corresponding to a hydrogen-cesium mixture are used with different initial temperatures being selected to investigate the effects of changes in the shape of the k-T curve. Both stability and mean flow calculations are limited to the one-dimensional case. The mean flow results show a decrease in mass flow as laser power is increased, along with increasingly steep temperature profiles. Calculations span regions of partial and complete absorption. One region is found where multiple solutions exist. Local stability results indicate the u-c characteristic is the only unstable mode in the unheated case. Laser heat addition makes this mode more unstable and also destabilizes the u-characteristic. Numerical calculations of disturbance propagation show that the instability of the u-c disturbances is counteracted by their reflection to u + c disturbances at the upstream end. The growth of the u-disturbances is localized in regions where the temperature profile is steep and they are damped in other regions. The increasing destabilization that is observed with increased laser power is probably the reason for difficulty in obtaining converged mean flow solutions at high laser intensities.

Merkle, C. L.↗
NASA NTRS1986

Direct solar-pumped iodine laser amplifier

During this period the parametric studies of the iodine laser oscillator pumped by a Vortek simulator were carried out before amplifier studies. The amplifier studies are postponed to the extended period after completing the parametric studies. In addition, the kinetic modeling of a solar-pumped iodine laser amplifier, and the experimental work for a solar pumped dye laser amplifier are in progress. This report contains three parts: (1) a 10 W CW iodine laser pumped by a Vortek solar simulator; (2) kinetic modeling to predict the time to lasing threshold, lasing time, and energy output of solar-pumped iodine laser; and (3) the study of the dye laser amplifier pumped by a Tamarack solar simulator.

Han, K. S.↗
NASA NTRS1985

Pulsed excimer laser processing

The status of pulsed excimer laser processing of PV cells is presented. The cost effective feasibility of fabricating high efficiency solar cells on Czochralski wafers using a pulsed excimer laser for junction formation, surface passivation, and front metallization. Laser annealing results were promising with the best AR coated cell having an efficiency of 16.1%. Better results would be expected with larger laser spot size because there was some degradation in open circuit voltage caused by laser spot overlap and edge effects. Surface heating and photolytic decomposition by the laser was used to deposit tungsten from the reaction of tungsten hexafluoride and hydrogen. The line widths were 5 to 10 mils, and the depositions passed the tape adhesion test. Thinner lines are practical using an optimized optical system.

Wong, D.↗
NASA NTRS1987

Diffractively Coupled, Refractively Guided Lasers

Semiconductor-laser arrays more reliable, more powerful, and easier to make. Improved design intended to eliminate undesired electromagnetic modes and mode shifts sometimes occuring in gain-guided variety. Reflected from mirror/window at end of common resonator section of laser, energy refracted from each laser enters adjacent laser. Mutual coupling establishes phase relationships among lasers. Monolithic laser array made by standard epitaxial techniques. Made in part with polymeric materials to mitigate some deleterious effects of all-expitaxial processing. Potential applications include optical communications, ranging, printing, and recording.

Katz, Joseph↗
NASA NTRS1986

Space-based laser-driven MHD generator: Feasibility study

The feasibility of a laser-driven MHD generator, as a candidate receiver for a space-based laser power transmission system, was investigated. On the basis of reasonable parameters obtained in the literature, a model of the laser-driven MHD generator was developed with the assumptions of a steady, turbulent, two-dimensional flow. These assumptions were based on the continuous and steady generation of plasmas by the exposure of the continuous wave laser beam thus inducing a steady back pressure that enables the medium to flow steadily. The model considered here took the turbulent nature of plasmas into account in the two-dimensional geometry of the generator. For these conditions with the plasma parameters defining the thermal conductivity, viscosity, electrical conductivity for the plasma flow, a generator efficiency of 53.3% was calculated. If turbulent effects and nonequilibrium ionization are taken into account, the efficiency is 43.2%. The study shows that the laser-driven MHD system has potential as a laser power receiver for space applications because of its high energy conversion efficiency, high energy density and relatively simple mechanism as compared to other energy conversion cycles.

Choi, S. H.↗
NASA NTRS1986

Direct solar-pumped iodine laser amplifier

In order to evaluate the feasibility of the solar pumped dye laser, the parametric study of a dye laser amplifier pumped by a solar simulator and flashlamp was carried out, and the amplifier gains were measured at various pump beam irradiances on the dye cell. Rhodamine 6G was considered as a candidate for the solar pumped laser because of its good utilization of the solar spectrum and high quantum efficiency. The measurement shows that a solar concentration of 20,000 is required to reach the threshold of the dye. The work to construct a kinetic model algorithm which predicts the output parameter of laser was progressed. The kinetic model was improved such that there is good agreement between the theoretical model and experimental data for the systems defined previously as flashlamp pumped laser oscillator, and the long path length solar pumped laser.

Han, Kwang S.↗
NASA NTRS1986

Solar pumped laser technology options for space power transmission

An overview of long-range options for in-space laser power transmission is presented. The focus is on the new technology and research status of solar-pumped lasers and their solar concentration needs. The laser options include gas photodissociation lasers, optically-pumped solid-state lasers, and blackbody-pumped transfer lasers. The paper concludes with a summary of current research thrusts.

Conway, E. J.↗
NASA NTRS1987

A theoretical investigation of laser-sustained plasma thruster

A numerical code has been successfully developed for the investigation of thruster performance using a laser-sustained hydrogen plasma as the propellant. The plasma was sustained using a 10.6-micron CO2 laser beam focused at different positions within the thruster. The physical model assumed that plasma is in thermodynamical equilibrium (LTE), and geometric ray tracing was adopted to describe the laser beam. The steady-state, axisymmetric, Navier-Stokes equations coupled with the laser power absorption process have been solved numerically. A pressure based Navier-Stokes numerical solver using body-fitted coordinates was used to calculate the laser-supported rocket flow which includes both subsonic and supersonic flow regions. From the limited parametric study, which did not try to optimize the rocket performance, it was found that better performance was obtained when the laser beam was focused closer to the rocket throat.

Jeng, San-Mou↗
NASA NTRS1987

A theoretical evaluation of laser-sustained plasma thruster performance

An extensive numerical experiment has been conducted to evaluate rocket thruster performance using a laser-sustained hydrogen plasma as the propellant. The plasma was sustained using a 30 kW CO2 laser beam operated at 10.6 microns focused inside the thruster. The steady-state Navier-Stokes equations coupled with the laser power absorption process have been solved numerically. A pressure based Navier-Stokes solver using body-fitted coordinate was used to calculate the laser-supported rocket flow which included both recirculating and transonic flow regions. The local thermodynamic equilibrium (LTE) assumption was used for the plasma thermophysical and optical properties. Geometric ray tracing was adopted to describe the laser beam. Several different throat size thrusters operated at 150 and 300 kPa chamber stagnation pressure were studied. It was found that the thruster performance (vacuum specific impulse) was highly dependent on the operating conditions, and a properly designed laser supported thruster can attain a specific impulse around 1500 secs. The heat loading on the thruster wall was also estimated and was in the range of that for a conventional chemical rocket.

Jeng, San-Mou↗
NASA NTRS1988

Compact Ho:YLF Laser

Longitudinal pumping by laser diodes increases efficiency. Improved holmium:yttrium lithium fluoride laser radiates as much as 56 mW of power at wavelength of 2.1 micrometer. New Ho:YLF laser more compact and efficient than older, more powerful devices of this type. Compact, efficient Ho:YLF laser based on recent successes in use of diode lasers to pump other types of solid-state lasers.

Hemmati, H.↗
NASA NTRS1987

The laser elevator - Momentum transfer using an optical resonator

In a conventional laser lightsail system the payload is propelled by the momentum imparted to it by the reflection of a laser beam without the use of any propellant. Because of the unfavorable relationship between energy and momentum in a light beam, these systems are very inefficient. The efficiency can be greatly improved, in principle, if the photons that impact the payload mirror are returned to the source and then redirected back toward the payload again. This system, which recirculates the laser beam, is defined as the 'laser elevator'. The gain of the laser elevator over conventional lightsails depends on the number of times the beam is recycled which is limited by the reflectance of the mirrors used, any losses in the transmission of the beam, and diffraction. Due to the increase pathlength of the folded beam, diffraction losses occur at smaller separations of the payload and the source mirror than for conventional lightsail system. The laser elevator has potential applications in launching to low earth orbit, orbital transfer, and rapid interplanetary delivery of small payloads.

Meyer, Thomas R.↗
NASA NTRS1989

Q-Switch For Self-Injection Locking Of Laser

Proposed scheme for improved electro-optical switching (Q switching) of pulsed, self-injection-locked laser involves sensing of and compensation for level of pumping light. Decreases spectral width of laser pulse and makes it independent of pumping level. Laser operated in high-loss condition during initial evolution of pulse. During this time, light makes many round trips through laser resonator. Once small laser pulse evolves in high-loss condition in laser resonator, optical configuration of resonator switched to one of low loss. In low-loss state, majority of energy extracted in efficient manner while retaining narrow spectral width of initial pulse. Beneficial in reducing jitter.

Barnes, Norman P.↗
NASA NTRS1988

Monolithic two-dimensional surface-emitting arrays of GaAs/AlGaAs diode lasers

Monolithic two-dimensional arrays of GaAs/AlGaAs diode lasers with light emission normal to the surface have been obtained by fabricating edge-emitting quantum-well lasers coupled with external mirrors that deflect the radiation from the laser facets by 90 degrees. Linear arrays of GaAs/AlGaAs devices in which one of the laser facets was cleaved while the other facet and an adjacent 45 degree deflector were formed by ion-beam-assisted etching (IBAE) have been reported. For the arrays reported in this section, IBAE was used to form all of the laser facets and the deflecting mirrors. A mass transport process of the type employed to fabricate two-dimensional arrays of GaInAsP/InP lasers coupled with deflecting mirrors is not known for AlGaAs.

Source record↗
NASA NTRS1988

Atmospheric transmission coefficients for laser pulses with spectral widths of a few tenths of a nanometer over the wavelength region from 800 to 860 nanometers

Effective atmospheric transmission spectra were calculated from 800 to 860 nanometers for laser sources with spectral widths of a few tenths of a nanometer. In this spectral region, the atmospheric absorption lines (water lines) have linewidths of a few hundredths of a nanometer, so that the transmission coefficient for a relatively wide laser pulse must be computed by taking a weighted average over the pulse spectral width. Laser spectral widths of several tenths of a nanometer are shown to reduce the effective absorption by water lines to as little as 10 to 20 percent, even when the laser is centered on a line or overlaps several lines. Thus, the effect of absorption by atmospheric water lines may be greatly reduced for laser communication systems using laser diode array transmitters, for which the pulse spectral width may be a few tenths of a nanometer.

Safren, H. G.↗