Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Impact testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

The Effects of Impactor Shape on the Compression After Impact Strength of Carbon/Epoxy Face Sheet Aluminum Honeycomb Core Sandwich Structure

This study presents experimental results of compression after impact (CAI) strength testing of aluminum core sandwich structure with carbon/epoxy face sheets impacted at three different energies with either a 12.7 mm hemispherical, 24.5 mm hemispherical or sharp tip impactor. This study was undertaken to verify whether design allowables typically generated by blunt (hemispherical) impactors may be valid in ‘real world” applications where an impact may not be by a blunt object of a specific size. Results of practical interest in this study were that the visual damage was much easier to see for the sharp impactor, the damage size as detected by thermography was smaller for the sharp impactor for a given impact energy and dent depth was greater for the sharp impactor. The CAI strength results showed that the sharp impactor gave about the same CAI strength values at all three impact energy levels used. The larger hemispherical impactor gave slightly higher CAI results than the smaller blunt impactor. Overall it was deemed difficult to develop a CAI allowable that would cover all impactor shapes with any fidelity and thus using a lower bound strain allowable is suggested.

compression after impact (CAI)↗
NASA NTRS1988

Measurements of matrix cracking and delamination caused by impact on composite plates

Tests were performed measuring the locations and extents of delaminations and matrix crackings in 3-in. by 3-in. Fiberite T300/934 graphite/epoxy plates impacted by 1/2-in. diameter aluminum spheres. Plates with six ply orientations were tested. The impactor speeds ranged from 700 to 1300 in/sec. The plates were inspected by C-scan both before and after impact. The plates were also dissected after impact and examined visually for damage. In addition, the longitudinal and transverse tensile, compressive, and shear properties of the material were measured.

Wu, Hsi-Yung T.↗
NASA NTRSDate not supplied

Lower neck injury criteria for THOR and Hybrid III dummies in rear impact

The objectives of the study are to derive lower-neck-injury probability curves under rear impact loading from matched pair Hybrid III and THOR dummy tests. Methods: Twelve whole-body and 15 isolated head-neck rear-impact sled tests were conducted using the 2 dummies. They were positioned on a rigid seat that was attached to an acceleration sled. The dummies were positioned with the head parallel to the ground, torso against the seat back, and legs stretched such that there was no axial rotation. The acceleration pulse matched the previous in-house human cadaver tests. The 6-axis lower-neck load cell was used in both dummies. For the isolated rear-impact tests,the head-neck was excised from the dummies, and the lower-neck load cell was mounted to the top of the sled with the head parallel to the ground and such that the acceleration vector was in the rear impact mode. Lower-neck loads and lower-neck-injury criteria (LNij) were obtained using the load cell data and survival analysis to develop injury-assessment-risk values and curves for both dummies. The LNij criteria were determined for both dummies using the intercept value corresponding to the 90% probability level for the forces and moments. Results: The log normal and Weibull distributions were the optimal distributions for the Hybrid III and THOR devices. At the 50% risk level, the mean LNij of 1.1 and NCIS was 0.77 for the Hybrid III, and 1.5 NCIS was 0.30 for the THOR device. The quality indices were in the fair range and good range for the 2 dummies, respectively, at this risk level. Conclusions: The lower-neck-based IARCs and IARVs serve as the first dataset for injury assessments, and the THOR may be a better test device for assessing injures in rear impact environments.

Narayan Yoganandan↗
NASA NTRS2017

Shape Effect Analysis of Aluminum Projectile Impact on Whipple Shields

The informed design with respect to hypervelocity collisions involving micrometeoroid and orbital debris (MMOD) is influential to the success of space missions. For an orbit comparable to that of the International Space Station, velocities for MMOD can range from 1 to 15 km/s, with an average velocity around 10 km/cu s. The high energy released during collisions at these speeds can result in damage to a spacecraft, or worst-case, loss of the spacecraft, thus outlining the importance of methods to predict the likelihood and extent of damage due to an impact. Through experimental testing and numerical simulations, substantial work has been conducted to better understand the effects of hypervelocity impacts (HVI) on spacecraft systems and shields; however, much of the work has been focused on spherical impacting particles. To improve environment models for the analysis of MMOD, a large-scale satellite break-up test was performed at the Arnold Engineering and Development Complex to better understand the varied impactor geometries that could be generated from a large impact. As a part of the post-experiment analysis, an undertaking to characterize the irregular fragments generated is currently being performed by the University of Florida under the management of NASA's Orbital Debris Program Office at Johnson Space Center (JSC). DebriSat was a representative, modern LEO satellite that was catastrophically broken up in a HVI test. The test chamber was lined with a soft-catch system of foam panels that captured the fragments after impact. Initial predictions put the number of fragments larger than 2mm generated from the HVI at roughly 85,000. The number of fragments thus far extracted from the foam panels has exceeded 100,000, with that number continuously increasing. The shapes of the fragments vary dependent upon the material. Carbon-fiber reinforced polymer pieces, for instance, are abundantly found as thin, flat slivers. The characterization of these fragments with respect to their mass, size, and material composition needs to be summarized in a form that can be used in MMOD analysis. The mechanism that brings these fragment traits into MMOD analysis is through ballistic limit equations (BLE) that have been developed largely for a few types of materials1. As a BLE provides the failure threshold for a shield or spacecraft component based on parameters such as the projectile impact velocity and size, and the target's materials, thickness, and configuration, it is used to design protective shields for spacecraft such as Whipple shields (WS) to an acceptable risk level. The majority of experiments and simulations to test shields and validate BLEs have, heretofore, largely used spheres as the impactor, not properly reflecting the irregular shapes of MMOD. This shortfall has motivated a numerical impact analysis study of HVI involving non-spherical geometries to identify key parameters that environment models should provide.

Carrasquilla, Maria J.↗
DOE OSTI2024

Impact of High-Reactivity Advanced Test Reactor Experiments on Photon Heating in Nearby Experiment Locations

The Advanced Test Reactor’s (ATR’s) distinctive ability to provide a wide range of irradiation conditions is attractive for programs pursuing fuel qualification experiments. These potentially high-fuel-load experiments are a relatively new development and produce unexplored effects on nearby experiments. Here, this paper explores how photon heating of such an experiment may affect other nearby experiment programs, ultimately serving to better inform decisions regarding experiment design and risks to programmatic goals. The MC21 (Monte Carlo for the 21st Century) code is used to model and study how gamma heat generation rates and axial effects impact different ATR positions. The results reveal that the proximity of a given experiment’s position to the high-fuel-load one can significantly alter that experiment’s expected axial profile.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Advancing the mechanical integrity and fragmentation behavior of reactive projectiles

A multivariant statistical approach was used to identify treatment conditions that improve the survivability of structural reactive material (SRM) projectiles upon launch and enhance energy release upon impact. The study included both mechanical testing of projectiles as well as their reactive characterization. The projectiles were launched in a high-velocity impact-ignition testing system and impacted an anvil for vented chamber calorimetry. This study examined a link between ultimate compressive stress and combustion performance. Two treatments were applied to consolidated aluminum projectiles including annealing and addition of silica (SiO 2 ) inclusions. Results showed annealing at moderate temperatures resulted in intact SRM projectiles upon launch. Adding small concentrations (1–2 wt. %) of SiO 2 to the SRM promoted fragmentation and combustion performance upon impact. Compared to the untreated projectiles, annealing with SiO 2 inclusion processing treatments improved the energy conversion efficiency from 37–84% (for untreated projectiles) up to 54–98%. In conclusion, increasing interparticle dislocation recovery by annealing while balancing inclusions promoting fragmentation upon impact was the key to optimizing combustion performance for SRM ballistic impact applications.

42 ENGINEERING↗
DOE OSTI2022

Effects of Impact and Target Parameters on the Results of a Kinetic Impactor: Predictions for the Double Asteroid Redirection Test (DART) Mission

Abstract The Double Asteroid Redirection Test (DART) spacecraft will impact into the asteroid Dimorphos on 2022 September 26 as a test of the kinetic impactor technique for planetary defense. The efficiency of the deflection following a kinetic impactor can be represented using the momentum enhancement factor, β , which is dependent on factors such as impact geometry and the specific target material properties. Currently, very little is known about Dimorphos and its material properties, which introduces uncertainty in the results of the deflection efficiency observables, including crater formation, ejecta distribution, and β . The DART Impact Modeling Working Group (IWG) is responsible for using impact simulations to better understand the results of the DART impact. Pre-impact simulation studies also provide considerable insight into how different properties and impact scenarios affect momentum enhancement following a kinetic impact. This insight provides a basis for predicting the effects of the DART impact and the first understanding of how to interpret results following the encounter. Following the DART impact, the knowledge gained from these studies will inform the initial simulations that will recreate the impact conditions, including providing estimates for potential material properties of Dimorphos and β resulting from DART’s impact. This paper summarizes, at a high level, what has been learned from the IWG simulations and experiments in preparation for the DART impact. While unknown, estimates for reasonable potential material properties of Dimorphos provide predictions for β of 1–5, depending on end-member cases in the strength regime.

58 GEOSCIENCES↗
NASA NTRS2016

Imparting Barely Visible Impact Damage to a Stitched Composite Large-Scale Pressure Box

The Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) is a concept that was developed by The Boeing Company to address the complex structural design aspects associated with a pressurized hybrid wing body (HWB) aircraft configuration, which has been a focus of the NASA Environmentally Responsible Aviation Project. The NASA-Boeing structural development for the HWB aircraft culminated in testing of the multi-bay box, which is an 80%-scale representation of the pressurized center-body section. This structure was tested in the NASA Langley Research Center Combined Loads Test System facility. As part of this testing, barely visible impact damage was imparted to the interior and exterior of the test article to demonstrate compliance with a condition representative of the requirements for Category 1 damaged composite structure as defined by the Federal Aviation Regulations. Interior impacts were imparted using an existing spring-loaded impactor, while the exterior impacts were imparted using a newly designed, gravity-driven impactor. This paper describes the impacts to the test article, and the design of the gravitydriven guided-weight impactor. The guided-weight impactor proved to be a very reliable method to impart barely visible impact damage in locations which are not easily accessible for a traditional drop-weight impactor, while at the same time having the capability to be highly configurable for use on other aircraft structures.

Lovejoy, Andrew E.↗
NASA NTRS1983

The effect of matrix properties and fiber properties on impact failure mechanics

The low-velocity impact problem in graphite/epoxy composite sheets must be solved before large amounts of that material can be used in commercial aircraft. Many of the low-velocity impacts that affect aircraft parts occur during normal ground operations and maintenance. Service equipment and tools have masses above 1 kg, and at velocities of less than 3 m/s can impact structural parts with energies higher than composites can endure without degradation of stiffness or strength. Simple solutions were developed for large-mass, low-velocity impacts which can be modeled as quasi-static events. Static test data and impact data show that the fiber properties control the impact energy which can be absorbed before penetration. Matrix shear strength and peel resistance control the extent of delamination. Comparison of results from tough matrix and brittle matrix composites show that although tough matrices reduce the extent of delamination, they lead to more fiber damage in the contact area.

Elber, W.↗
NASA NTRS1986

Modified US Army U-8F ground vibration test

The Dryden Flight Research Facility of NASA Ames Research Center conducted a ground vibration test on a modified U.S. Army U-8F airplane. Modifications included new engines, propellers, and engine-mounted truss assemblies. The ground vibration test was conducted using sine dwell, single-point random, and impact excitations. The test was performed to determine modal frequencies, mode shapes, and structural damping coefficients of the airframe and propeller with full and empty fuel tanks. The data presented include frequency response plots, rigid-body and structural modal frequencies, and mode shapes.

Kehoe, M. W.↗
NASA NTRSDate not supplied

Alternative MMOD Shielding Concepts

The main types of meteoroid and orbital debris (MMOD) shields are single-layer “monolithic” shields, dual-wall “Whipple” shields, and multi-wall shields (“Stuffed Whipple” and “multi-shock” are common types). Aluminum alloys are typically used for the outer bumper layer and for the rear wall of the dual- and multi-wall shields, although carbon-composites are increasingly employed in MMOD shields given their low-mass and high-strength. Ceramic (NextelTM) and KevlarTM fabrics are commonly used for the intermediate layers of Stuffed Whipple shields. The NASA Johnson Space Center (JSC) Hypervelocity Impact Technology (HVIT) group is continuously working to improve NASA spacecraft MMOD shielding by evaluating new materials and shielding concepts by test and analysis. HVIT has performed many hypervelocity impact tests over several years to evaluate alternative MMOD shield materials and concepts. This paper will provide results of this work in the following areas: (1) Material substitutions to improve radiation and MMOD protection within Stuffed Whipple shields, (2) Metallic and ceramic foam bumper and intermediate layer materials, (3) Self-sealing materials. In the first two areas listed above, the candidate shield materials were tested under similar test conditions and with fixed shield standoff and mass. Damage to the rear wall was quantified and compared to determine the best performing shield materials. In the self-sealing material evaluations, the test objective was to gauge the ability of different materials and techniques to stop leaks in a rear wall with a 1-atmosphere (air) delta-pressure across the wall. This paper provides results of the investigations and describes forward work to continue the development of the most promising MMOD shield alternatives. KevlarTM is a trademark of DuPont de Nemours, Inc. NextelTM is a trademark of 3M Corporation Note, Trade names and trademarks are used in this report for identification only. Their usage does not constitute an official endorsement, either expressed or implied, by the National Aeronautics and Space Administration.

Hypervelocity↗
NASA NTRS1989

The effect of hydrogen on mechanical properties of oxygen-strengthened titanium

The effect of oxygen on the hydrogen embrittlement in titanium was investigated in two Ti-based alloys containing different amounts of oxygen: 0.064 and 0.154, in wt pct. Tensile, impact, and hardness tests were performed with and without prior hydrogenation of the specimens. Results show that, while the presence of hydrogen, even in relatively small amounts, will not affect the hardness or room-temperature tensile properties determined at relatively slow strain rates, hydrogen will reduce significantly the impact resistance, as determined by the Charpy V-notch test. This deleterious effect on the impact resistance was found to be exacerbated by an increase of oxygen in the alloy.

Wasz, M. L.↗
NASA NTRS1987

Space station integrated wall design and penetration damage control

A methodology was developed to allow a designer to optimize the pressure wall, insulation, and meteoroid/debris shield system of a manned spacecraft for a given spacecraft configuration and threat environment. The threat environment consists of meteoroids and orbital debris, as specified for an arbitrary orbit and expected lifetime. An overall probability of no penetration is calculated, as well as contours of equal threat that take into account spacecraft geometry and orientation. Techniques, tools, and procedures for repairing an impacted and penetrated pressure wall were developed and tested. These techniques are applied from the spacecraft interior and account for the possibility of performing the repair in a vacuum. Hypervelocity impact testing was conducted to: (1) develop and refine appropriate penetration functions, and (2) determine the internal effects of a penetration on personnel and equipment.

Coronado, A. R.↗
DOE OSTI2022

Operation Redwing

Cherokee exploded with an impressive yield of 3.8 megatons but missed its aiming point by six miles. Although regrettable, the miss was not overly significant because the event proved “that the United States owned a real [thermonuclear] weapon.” Cherokee was the second of seventeen tests conducted during Operation Redwing, whose primary purpose was to proof test bombs and warheads for an emerging generation of weapon systems. Eleven tests took place at Enewetak Atoll and six at Bikini Atoll. The parsing of tests between the two atolls was based largely on expected yields. Lower yield tests were held at Enewetak with the expectation that they would not impact the permanent tests facilities located on the atoll. Higher yield shots were detonated at Bikini. Although this division worked for the most part, fallout from one Bikini test, Tewa, reached Enewetak, contaminating both personnel and permanent test facilities.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
NASA NTRS1979

Space Shuttle Solid Rocket Booster decelerator subsystem - Air drop test vehicle/B-52 design

The air drop development test program for the Space Shuttle Solid Rocket Booster Recovery System required the design of a large drop test vehicle that would meet all the stringent requirements placed on it by structural loads, safety considerations, flight recovery system interfaces, and sequence. The drop test vehicle had to have the capability to test the drogue and the three main parachutes both separately and in the total flight deployment sequence and still be low-cost to fit in a low-budget development program. The design to test large ribbon parachutes to loads of 300,000 pounds required the detailed investigation and integration of several parameters such as carrier aircraft mechanical interface, drop test vehicle ground transportability, impact point ground penetration, salvageability, drop test vehicle intelligence, flight design hardware interfaces, and packaging fidelity.

Runkle, R. E.↗
NASA NTRS1987

A test of the longevity of impact-induced faults as preferred sites for later tectonic activity

The hypothesis that impact-induced faults have been preferred sites for later deformation in response to lithospheric stresses has been suggested for several planets and satellites. This hypothesis is investigated on earth by examining whether terrestrial impact structures show higher rates of nearby earthquake activity than do surrounding intraplate regions. For 28 of 30 probable impact structures having an original crater 20 km or more in diameter, the rates of nearby seismicity have been no higher than the regional background rates. For two large probable impact structures, Vredefort and Charlevoix, with higher than normal rates of nearby seismicity, factors other than slip on impact-induced faults appear to control the occurrence of earthquakes. It is concluded that impact-induced faults, at least on earth, do not persist as lithospheric 'weak zones' for periods in excess of several million years after the impact event.

Solomon, Sean C.↗