Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Hover”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

HARP model rotor test at the DNW

Data from a test of a dynamically scaled model of the Hughes Advanced Rotor Program (HARP) bearingless model main rotor and 369K tail rotor are reported. The history of the HARP program and its goals are reviewed, and the main and tail rotor models are described. The test facilities and instrumentation are described, and wind tunnel test data are presented on hover, forward flight performance, and blade-vortex interaction. Performance data, acoustic data, and dynamic data from near field/far field and shear layer studies are presented.

Dawson, Seth↗

Tilt rotor aircraft aeroacoustics

This paper studies the state of knowledge and the needed improvement in noise methodology and measurements for tilt rotor aircraft. Similarities and differences between tilt rotor aeroacoustic conditions and helicopter and propeller experience are identified. A discussion of the possible principal noise mechanisms throughout the flight envelope shows a need for further experimental and analytical investigations to develop an adequate understanding of the important sources and influencing factors. Existing experimental data from flight tests suggest terminal area noise reduction by operating within certain portions of the conversion flight envelope. Prediction methods are found to provide approximate indications only for low frequency harmonic and broadband noise for several of the tilt rotor's operating conditions. The acoustic effects of the hover case 'fountain' flow are pronounced and need further research. Impulsive noise and high frequency harmonic noise remain problems, as on helicopters, pending major improvements in wake, unsteady aerodynamics, and acoustics methodology.

George, Albert R.↗

The prediction of loads on the Boeing Helicopters Model 360 rotor

Results are presented from a test/theory correlation investigation involving three rotor-analysis codes, two full potential rotor flow CFD solvers, and data obtained from tests on the Model 360 helicopter's rotor. Attention is given to the problem of reliable higher harmonic loading prediction. It is found that the rotor hover performance and loading experimental data are in excellent agreement with a novel, full potential free-wake computational technology; the need for a multiple tip-vortex wake model's use in predicting vibratory airloads is confirmed.

Dadone, Leo↗

Rotary-wing aeroelasticity with application to VTOL vehicles

This survey presents an assessment of the state of the art in rotary-wing aeroelasticity as applied to conventional helicopters as well as other VTOL vehicles such as tilting prop-rotors, the X-wing and a hybrid heavy lift vehicle. The objective is to enable the reader to develop an awareness of what has been accomplished, what remains to be done, and where to find more comprehensive treatments of the various topics discussed. The main topics discussed are: (1) structural modeling; (2) unsteady aerodynamic modeling; (3) formulation of the equations of motion and their solutions; (4) illustrative results for isolated blades in hover and forward flight; (5) illustrative results for coupled rotor/fuselage problems; (6) active control of aeromechanical and aeroelastic problems; (7) active controls for vibration reduction; (8) structural optimization with aeroelastic constraints; (9) gust response analysis of rotors; and (10) aeroelastic problems in special VTOL vehicles. These topics are reviewed with different levels of detail and some useful observation on potentially rewarding areas of future research are made.

Friedmann, Peretz P.↗

Application of transonic flow analysis to helicopter rotor problems

The transonic aspect of helicopter flow analysis is addressed. The equations of motion and their implementations are examined, and the computation of real rotor flows is considered. Nonlifting rotor flows, high-speed hover, high advance ratio lifting rotor flows, and strong blade/vortex interaction computations are discussed.

Caradonna, F. X.↗

A survey of nonuniform inflow models for rotorcraft flight dynamics and control applications

The results of a brief survey of nonuniform inflow models was summarized for the calculation of induced velocities at and near a lifting rotor in and out of ground effect. The survey, conducted from the perspective of flight dynamics and control applications, covers a spectrum of flight conditions including hover, vertical flight, and flow-speed and high-speed forward flight, and reviews both static and dynamic aspects of the inflow. A primary emphasis is on the evaluation of various simple first harmonic inflow models developed over the years, in comparison with more sophisticated methods developed for use in performance and airload computations. The results of correlation with several sets of test data obtained at the rotor out of ground effect indicate that the Pitt/Peters first harmonic inflow model works well overall. For inflow near the rotor or in ground effect, it is suggested that charts similar to those of Heyson/Katzoff and Castles/De Leeuw of NACA be produced using modern free-wake methods for use in flight dynamic analyses and simulations.

Chen, Robert T. N.↗

Flight/propulsion control integration for V/STOL fighter/attack aircraft

A NASA-defined technology program investigating integrated flight/propulsion control system design for vertical and short takeoff and landing (V/STOL) aircraft is outlined, and initial fixed-base simulation experiments for two V/STOL aircraft are covered. It is shown that transition performance can be characterized by the minimum climb or level-flight acceleration that can be achieved. Level-1 flying qualities can be achieved for deceleration to hover in instrument conditions, and for shore-based and shipboard landing when attitude and velocity stabilization and command augmentation modes are provided. Level-1 and Level-2 flying qualities can be expected when only attitude command is provided. During vertical landing aboard a destroyer in heavy seas, substantial bleed flow rates are reported for a control arrangement employing reaction control for the pitch, roll, and yaw axes. Peak bleed flows can be reduced for a control arrangement using lateral-thrust transfer for roll control.

Franklin, James A.↗

The free-wake computation of rotor-body flows

In this paper a method is described for predicting the compressible, free-wake, flow about a lifting rotor-body configuration. The method is an extension of a unique vorticity embedded full-potential method used to calculate free-wake rotor hover performance. An unusual feature of this method is that it obviates the requirement for multiple grids to treat the rotor-body problem. The approach used to treat the body is similar to that used to include the rotor wake in the full potential calculation. The body is modeled as a structured circulation sheet and the strength of this sheet is determined in an iterative manner. Initially the method is tested to compute the flow past simple isolated bodies like cylinders and spheres. After a comparison of these simple computations with exact solutions this procedure is included into the HELIX-I, free-wake rotor code, to compute the flow around a rotor mounted on a large whirl tower. The effects of the tower on rotor wake geometry and load distribution are presented.

Ramachandran, K.↗

A review of tilt rotor download research

Experimental and theoretical research on the forces on a wing immersed in the wake of a hovering rotor is reviewed, with emphasis on the tilt rotor download problem. The basic features of the rotor/wing flow field on a tilt rotor aircraft are described. The effect of important geometric and operational parameters on the wing download is assessed. The magnitude of the download for typical tilt rotor configurations is reviewed, and advanced concepts for download reduction are described. Recommendations are presented for the direction of future research efforts.

Felker, Fort F.↗

Analysis of internal flow in a ventral nozzle for STOVL aircraft

Short takeoff and vertical landing (STOVL) aircraft are planned for possible future development. For these aircraft, the same propulsion system will provide power for lift, hover, and horizontal flight. To accomplish this, many designs include a ventral nozzle to provide part of the vertical thrust required. Understanding and predicting the internal aerodynamic flow caused by a single exhaust duct opening are highly desirable in assessing this concept. A numerical simulation of a ventral nozzle is presented and the results are compared with experimental data. Comparisons include visualizations of the flow along the ventral duct walls and in the tailpipe plane of symmetry. Performance calculations are also compared with measured values.

Smith, C. Frederic↗

Saturn ring rendezvous mission utilizing a tethered sub-satellite

By combining the advanced technologies of constant-thrust propulsion and space tethers in a planetary mission, it may be feasible to perform a complete radial and azimuthal survey of the Saturnian ring system from close range (about 10 km) in a period of some 300 days. Constant-thrust propulsion would provide the means of 'hovering' above the rings while simultaneously spiraling radially inward toward Saturn. Use of a tethered sub-satellite at a distance of 500-1000 km from the main spacecraft would permit an instrumented package to achieve a significant azimuthal angular rate relative to the rings. Exhaustive 360 deg azimuthal mapping at one or two selected distances from Saturn could be performed in a few tens of days.

Bright, Larry E.↗

Aerodynamic design of the Cal Poly Da Vinci Human-Powered Helicopter

This paper will discuss the methodology used in designing the rotor and drive propellers for the third generation Cal Poly Da Vinci Human-Powered Helicopter. The rotor was designed using a lifting surface, uniform inflow hover analysis code and the propeller was designed using a minimum induced-loss method. Construction, geometry, and operating considerations are discussed as they impact the designs. Optimization of the design performance is also explained. The propellers were tested in a wind tunnel and results are compared with theoretical data. Successful flight tests of the Da Vinci III are discussed.

Larwood, Scott↗

The implementation of STOVL task-tailored control modes in a fighter cockpit

The implementation of Short Takeoff/Vertical Landing (STOVL) specific task tailored control modes in a supersonic fighter/attack aircraft cockpit is investigated. A detailed linear model exhibiting STOVL Level 1 handling qualities is implemented in a real time engineering workstation environment with an F-16 cockpit mock-up. Conventional F-16 control inceptors are utilized to achieve effective STOVL operation and reduced pilot workload throughout the transition to hover flight region. Favorable pilot comments indicate the existing F-16 cockpit configuration with a force sidestick is adaptable to STOVL operation.

Whatley, David W.↗

Selected design issues of some high speed rotorcraft concepts

A study of vehicle concepts for High Speed Rotorcraft applications has been undertaken at Ames Research Center in cooperation with NASA Lewis and Langley Centers, with the objective of defining their technology needs. The design guidelines include a low downwash velocity in hover, good low speed maneuver capabilities and cruise speeds up to 450 knots. Four contractors and a systems analysis effort within NASA have defined promising configurations which may be capable of meeting these goals. This paper addresses challenging problems associated with some of the configurations in the areas of aerodynamics, propulsion, weights and aeroelastic stability.

Talbot, Peter D.↗

Transonic flow analysis for rotors. Part 3: Three-dimensional, quasi-steady, Euler calculation

A new method is presented for calculating the quasi-steady transonic flow over a lifting or non-lifting rotor blade in both hover and forward flight by using Euler equations. The approach is to solve Euler equations in a rotor-fixed frame of reference using a finite volume method. A computer program was developed and was then verified by comparison with wind-tunnel data. In all cases considered, good agreement was found with published experimental data.

Chang, I-Chung↗

Numerical simulation of rotorcraft

The objective of the research is to develop and validate accurate, user-oriented viscous CFD codes (with inviscid options) for three-dimensional, unsteady aerodynamic flows about arbitrary rotorcraft configurations. Unsteady, three-dimensional Euler and Navier-Stokes codes are developed, adapted, and extended to rotor-body combinations. Flow solvers are coupled with zonal grid topologies, including rotating and nonrotating blocks. Special grid clustering and wave-fitting techniques were developed to capture low-level radiating acoustic waves. Significant progress was made in computing the propagation of acoustic waves due to the interaction of a concentrated vortex and a helicopter airfoil. The need for higher-order schemes was firmly established in relatively inexpensive two-dimensional calculations. In three dimensions, the number of grid points required to capture the low-level acoustic waves becomes very large, so that large supercomputer memory becomes essential. Good agreement was obtained between the numerical results obtained with a thin-layer Navier-Stokes code and experimental data from a model rotor. In addition, several nonrotating configurations that are sometimes proposed to simulate rotor blade tips in conventional wind tunnels were examined, and the complex flow around the radical tip shape of the world's fastest helicopter is under investigation. These studies demonstrate the flexibility and power of CFD to gain physical insight, study novel ideas, and examine various possibilities that might be difficult or impossible to set up in physical experiments. As a prelude to studies of rotor-body aerodynamic interactions, a preliminary grid topology and moving-interface strategy were developed. A new Euler/Navier-Stokes code using these techniques computes the vortical wake directly, rather than modeling it, as in most previous rotorcraft studies. Several hover cases were run for conventional and advanced-geometry blades. Numerical schemes using multi-zones and/or adaptive grids appear to be necessary to simulate the complex vortical flows in rotor wakes.

Mccroskey, William J.↗

Small-scale experiments in STOVL ground effects

A series of tests was completed in which suckdown and fountain forces and pressures were measured on circular plates and twin-tandem-jet generic STOVL (short takeoff and vertical landing) configurations. The tests were conducted using a small-scale hover rig, for jet pressure ratios up to 6 and jet temperatures up to 700 F. The measured suckdown force on a circular plate with a central jet was greater than that found with a commonly used empirical prediction method. The present data showed better agreement with other sets of data. The tests of the generic STOVL configurations were conducted to provide force and pressure data with a parametric variation of parameters so that an empirical prediction method could be developed. The effects of jet pressure ratio and temperature were found to be small. Lift improvement devices were shown to substantially reduce the net suckdown forces.

Corsiglia, Victor R.↗

Technology needs for high-speed rotorcraft

A study to determine the technology development required for high-speed rotorcraft development was conducted. The study begins with an initial assessment of six concepts capable of flight at, or greater than 450 knots with helicopter-like hover efficiency (disk loading less than 50 pfs). These concepts were sized and evaluated based on measures of effectiveness and operational considerations. Additionally, an initial assessment of the impact of technology advances on the vehicles attributes was made. From these initial concepts a tilt wing and rotor/wing concepts were selected for further evaluation. A more detailed examination of conversion and technology trade studies were conducted on these two vehicles, each sized for a different mission.

Rutherford, John↗