Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EUTECTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

High Chromium Cast Irons: Destabilized-Subcritical Secondary Carbide Precipitation and Its Effect on Hardness and Wear Properties

This work evaluates the effect of a destabilization treatment combined with a subcritical diffusion (SCD) and a subsequent quenching (Q) steps on precipitation of secondary carbides and their influence on the wear properties of HCCI (16%Cr). The destabilization of the austenite at high temperature leads to a final microstructure composed of eutectic and secondary carbides, with an M{sub 7}C{sub 3} nature, embedded in a martensitic matrix. An improved wear resistance was observed in the SCD + Q samples in comparison with the Q one, which was attributed to the size of secondary carbides.

36 MATERIALS SCIENCE↗

The Effect of Boron and Zirconium on the Structure and Tensile Properties of the Cast Nickel-Based Superalloy ATI 718Plus

The effects of boron and zirconium on cast structure, hardness, and tensile properties of the nickel-based superalloy 718Plus were investigated. For this purpose, five alloys with different contents of boron and zirconium were cast via vacuum induction melting and then purified via vacuum arc remelting. Microstructural analysis by light-optical microscope and scanning electron microscope equipped with energy-dispersive x-ray spectroscopy and phase studies by x-ray diffraction analysis were performed. The results showed that boron and zirconium tend to significantly reduce dendritic arm spacing and increase the amount of Laves, Laves/gamma eutectic, and carbide phases. It was also found that boron led to the formation of B{sub 4}C and (Cr, Fe, Mo, Ni, Ti){sub 3}B{sub 2} phases and zirconium led to the formation of intermetallic phases and ZrC carbide. In the presence of boron and zirconium, the hardness and its difference between dendritic branches and inter-dendritic spaces increased by concentrating such phases as Laves in the inter-dendritic spaces. These elements had a negative effect on tensile properties of the alloy, including ductility and strength, mainly because of the increase in the Laves phase. It should be noted that the largest degradation of the tensile properties occurred in the alloys containing the maximum amount of zirconium.

36 MATERIALS SCIENCE↗

Mechanical Properties and Microstructural Evolution of Yb-Modified Al-20%Si Alloy

In the study, the mechanical properties and microstructural evolution of hypereutectic Al-20%Si-xYb alloys (x = 0, 0.1, 0.3, 0.5 and 0.7 wt.%) were studied. The as-prepared samples were characterized by scanning electron microscopy, optical microscope, x-ray diffraction (XRD) and electron probe microanalysis. The characterization results showed with the addition amount of Yb increasing to 0.5%, the eutectic Si structure was gradually modified from coarse needle-like/platelet-like structure into fine coral-like fibrous structure and the primary Si phases were gradually converted from coarse platelet-like/star-like/polygonal shape into fine blocky shape. In particular, according to the results of WDS and XRD analyses, the Yb-rich intermetallic phase in the Al-20%Si alloy is Al{sub 3}Yb. Tensile test was carried out to study the mechanical properties of Al-20%Si-x%Yb alloys, and results showed that the elongation and ultimate tensile strength increased by 73.6% and 64.5%, respectively.

36 MATERIALS SCIENCE↗

Effects of Nb on the Microstructure and Properties of Ti-Added Hypereutectic High-Cr Cast Iron

Effects of Nb on the microstructure and properties of Ti-added hypereutectic high-Cr cast iron were studied. With the addition of Nb, a new phase (Nb,Ti)C was formed. The microstructure analysis revealed that the amount of primary carbides was decreased from 18.6 to 8.8% and the primary and eutectic carbides were greatly refined. The decrease in the amount of primary carbides was attributed with the shrinking of primary M{sub 7}C{sub 3} phase zone in the phase diagram, while the refinement of primary carbides was attributed to the heterogeneous nucleus of (Nb,Ti)C phase for the primary M{sub 7}C{sub 3} carbides. The macrohardness of the alloy increased from 60.8 to 63.5HRC, and the impact toughness increased from 3.8 to 5.2 J cm{sup −2}. Furthermore, the wear resistance was enhanced with the addition of Nb due to the formation of hard (Nb,Ti)C carbides.

36 MATERIALS SCIENCE↗

Pulse MIG Welding of 6061-T6/A356-T6 Aluminum Alloy Dissimilar T-joint

Dissimilar T-joints between 4-mm-thick wrought 6061-T6 and cast A356-T6 aluminum alloy plates are made with pulse metal inert gas welding (P-MIG) process, and the weld geometry, microstructure and mechanical properties of the joints are investigated. The average tensile load of the joints is 9488 N at travel speed 12 mm/s and welding current 165 A with 6061 aluminum alloy as web plate and A356 aluminum alloy as flange plate. The weld zone (WZ) is composed of dendrite zone and columnar zone, which is wide at bottom of weld making it become a weak zone. Besides, grain boundary (GB) liquation, consisting of GB eutectic and solute-depleted α-Al, occurs in the partially melted zone on 6061 aluminum alloy side. The T-joint with highest tensile load fails at the root of WZ and the flange plate near the weld with different fracture modes.

36 MATERIALS SCIENCE↗

The Influence of Galvanizing Parameters on the Structural Development of Zn-Al-Based Coatings

The evolution of some layers’ characteristics, deposited by galvanization, was monitored according to the technological parameters of the process. Two types of alloys from the Zn-Al and Zn-Al-Ti-B systems were used for deposition. The structure of the deposited layers was analyzed by optical and electron microscopy. The chemical composition, phases and compounds in the structures were identified. The mechanical properties of the structural constituents of the layers were determined by nanoindentation. These techniques highlighted the typical non-uniformities in terms of composition and properties in the layers, mainly due to the diffusion and distribution of iron from the steel substrate in the deposited layers. The evaluation of iron diffusion in the deposited layer was done by differential thermal analysis. The values of the critical temperatures (melting temperature, eutectic temperature and solidification temperature) were correlated with the parameters used during deposition. It was observed that the structure of the coatings is layered, with a specific order from the steel substrate to the edge. In these layers, the constituents are mixtures of soft solid solutions of Al in Zn (η and β) and hard intermetallic compounds. Moreover, increasing the immersion time in the galvanizing bath and the bath temperature leads to an increase in iron diffusion in the coating layer, which contributes to lower coating thickness, thus reducing its durability in operation.

36 MATERIALS SCIENCE↗

Enhanced Strength of 304 SS-Ti6Al4V Laser-Welded Joints Containing Composite Interlayers

This paper investigates the microstructural characterization of the fracture propagation edge during laser beam welding of Ti6Al4V and 304 stainless steel using Cu, V, and Ni interlayers as a single Cu interlayer and composite interlayer structures with different Cu interlayer thicknesses. This study attempts to increase the Ti-SS joint strength through the use of the composite interlayers. X-ray diffraction characterization based on a 0.5-mm-thick Cu interlayer showed that the SS/Cu/Ti joint contained considerable brittle IMCs; however, the fracture surface of the SS/Cu-V/Ti composite interlayer sample did not contain any Fe-Ti IMCs or Cr{sub 2}Ti. EBSD observation indicated that the crack propagated transgranularly from solidified CuTi in the interdendritic regions of the FeTi compounds in the composite interlayer sample; however, the crack propagated intergranularly along Fe{sub 2}Ti grain boundaries in the single interlayer sample. The investigation based on a 1-mm-thick Cu interlayer showed that the SS/Ni-Cu1/Ti sample was stronger than the SS/Cu1/Ti sample due to a lack of CuTi at 3.5 kW. The tensile strength of the SS/Cu1-V/Ti joint was greater than that of the SS/Ni-Cu1/Ti joint due to the formation of ductile NiTi instead of brittle NiTi{sub 2}. The microstructures of the fracture edges after tensile testing illustrated that the eutectic CuTi + CuTi{sub 2} fractured at the SS/Cu1/Ti joint after tensile testing, while CuTi{sub 2} and eutectoid αTi + CuTi{sub 2} compounds fractured during the tensile experiment at the SS/Ni-Cu1/Ti and SS/Cu1-V/Ti joints, respectively. Investigations based on both the 0.5- and 1-mm-thick Cu interlayers showed that the tensile strength and elongation of the composite interlayer joints at a laser power of 3.5 kW were greater than those of the single interlayer joints.

36 MATERIALS SCIENCE↗

Study on Microstructure and Properties of AZ31/6061 GTAW Butt Joints According to Mg-Cd-Al Ternary System

AZ31 Mg and 6061 Al were successfully joined by GTAW method with Cd as filler metal. The tensile strength of the joints reached 170 MPa through this alloying method according to Mg-Cd-Al ternary system. The microstructure, phases, element distribution and fracture mechanism of alloyed joints were studied. The results suggest that the fusion zone is mainly composed of CdMg compounds and Al-based solid solution. A transitional zone thickness of 40-80 μm with few primary Al{sub 12}Mg{sub 17} and fine Al{sub 12}Mg{sub 17}-MCMS (MCMS represents a mixture of CdMg and CdMg{sub 3} compounds) eutectic is formed between the AZ31 base metal and fusion zone. The fracture surface presents three distinct regions because of the different distribution of Al{sub 12}Mg{sub 17} compounds in the transitional zone. The alloying with Cd filler metal can disperse Al{sub 12}Mg{sub 17} intermetallic compounds and form CdMg ordered compounds with excellent plasticity. Thus, the mechanical properties of alloyed joints have been significantly enhanced.

36 MATERIALS SCIENCE↗

Thermal Analysis of Cerium-Treated Chill-Cast Al-23 Si Alloy

The influence of elemental cerium addition on the cooling curve parameters and microstructure of hypereutectic Al-23Si alloy was investigated in this work. The cooling rate of the treated and untreated alloy samples was varied by solidifying the melt against chills of different materials in a stainless-steel tube. The cooling curve was recorded and nucleation temperatures of various phases in the alloy were measured. The results show that the chilling improves the effectiveness of the modifier. The two main phases of the alloy, primary silicon and eutectic silicon, were nucleated at temperatures of about 661.2 and 571.6 °C, respectively. The addition of Ce to slowly cooled alloys resulted in an increase in undercooling temperature of both the phases, with a decrease in its nucleation temperature, whereas the same additions increased the nucleation temperatures in chilled alloys. Based on the thermal analysis results, a relation between thermal analysis parameter (ΔT{sub G}) and silicon particle size of the alloy was proposed.

36 MATERIALS SCIENCE↗

Transmission Electron Microscopy (TEM) Study of the Oxide Layers Formed on Fe-12Cr-4Al Ferritic Alloy in an Oxygenated Pb-Bi Environment at 800°C

Liquid lead–bismuth eutectic (LBE) can serve as a heat transfer fluid for advanced nuclear applications as well as concentrated solar power but poses corrosion challenges for the structural materials at elevated temperatures. Oxide passivation of the surfaces of these materials during exposure to liquid LBE can inhibit such material degradation. In this study, transmission electron microscopy of oxides formed on Fe-Cr-Al alloy during exposure to lowoxygenated LBE at 800C has been performed. A complex structure of the oxide film has been revealed, consisting of a homogeneous inner layer of mostly Al 2 O 3 and a heterogeneous outer layer.

14 SOLAR ENERGY↗

Phase-Specific Elastic/Plastic Interface Interactions in Layered Cr-NiAl Structures

The depth-dependent, as-grown and deformation-induced strain and dislocations partitioned through the interfaces in a two-phase layered NiAl-Cr(Mo) structure are directly measured at the mesoscale using 3-D X-ray microdiffraction. It is demonstrated that in the as-grown, undeformed state, neighboring submicron Cr solid solution and NiAl eutectic lamellae (doped with {approx}3% Mo) form a heterointerface with 180{sup o} rotation around a <1 1 2> pole. It is shown that the mechanical response to the indentation of a layered composite with alternating Cr(Mo)-NiAl lamellae is distinct from the response of single-phase materials. In the center of the indent, after the load is released, the NiAl lamellae are under compressive forward stresses (with the same sign as the indentation-induced compression) while Cr solid solution lamellae are under tensile back stresses (with opposite sign from the indentation load). The depth-dependent alternation of compressive/tensile residual strains in the neighboring Cr solid solution and NiAl lamellae is understood in the framework of the Mughrabi's composite model considering two types of structure elements: harder and softer regions. Under indentation, both kinds of lamellae are assumed to deform compatibly. After the load is released, residual forward stresses are formed in the harder lamellae, and back stresses are formed in the mechanically softer lamellae. Line-broadening analysis of the intensity distribution along the diffraction vector reveals a 15-times increase in dislocation density in the near-surface zone in the center of the indent. Such a large increase is typical for severe deformation.

36 MATERIALS SCIENCE↗

Applications of biomass-derived solvents in biomass pretreatment – Strategies, challenges, and prospects

We report biomass pretreatment is considered a key step in the 2nd generation biofuel production from lignocellulosic biomass. Research on conventional biomass pretreatment solvents has mainly been focused on carbohydrate conversion efficiency, while their hazardousness and/or carbon intensity were not comprehensively considered. Recent sustainability issues request further consideration for eco-friendly and sustainable alternatives like biomass-derived solvents. Carbohydrate and lignin-derived solvents have been proposed and investigated as green alternatives in many biomass processes. In this review, the applications of different types of biomass pretreatment solvents, including organic, ionic liquid, and deep eutectic solvents, are thoroughly discussed. The role of water as a co-solvent in these pretreatment processes is also reviewed. Finally, current research challenges and prospects of utilizing biomass-derived pretreatment solvents for pretreatment are discussed. Given bioethanol's market potential and increasing public awareness about environmental concerns, it will be a priority adopting sustainable and green biomass pretreatment solvents in biorefinery.

09 BIOMASS FUELS↗

Green pretreatment strategies for enhanced microbial lipid fermentation and synergistic high-quality lignin recovery for next-generation integrated biorefineries

Miscanthus × giganteus (Mxg) is a warm-season perennial grass being commercialized as a biomass feedstock for temperate farms. Three process strategies were compared for converting Mxg into single-cell oil and extracted lignin intermediates, as hydrothermal (HT) processing and two natural deep eutectic solvents (NADES), ChCl:LA (choline chloride:lactic acid) and ChCl:Gly (choline chloride:glycerol). Pretreatments were performed at 10% and 50% solids loading at 140 °C, 2 h; HT: 190 °C, 10 min. Enzymatic hydrolysates, generated at 10% solids using washed and unwashed biomass, were evaluated for microbial lipid production. Maximum glucose conversions from washed biomass reached 83.5% (ChCl:LA), 52.7% (ChCl:Gly), and 74.0% (HT). Remarkably, NADES-derived hydrolysates effectively replaced refined sugars for the cultivation of the oleaginous yeast Rhodotorula toruloides, achieving ∼51% higher biomass (OD 90.7) and lipid titers of 19.36 g/L within 45 h using a two-stage fermentation strategy. Lipid contents ranged from 34.5–44.5% dry weight, demonstrating reduced reliance on purified sugars. Beyond carbohydrate valorization, ChCl:LA pretreatment enabled high-purity lignin recovery (>89%) in a lignin-first strategy. Structural analyses (2D-HSQC and ³¹P NMR) showed syringyl (78.15%), guaiacyl (15.15%), and p-hydroxyphenyl (6.41%) units, with higher phenolic hydroxyl content (0.91 mmol/g) and a lower S/G ratio (0.19) than HT lignin (0.87 mmol/g, S/G 0.22). These attributes favor downstream lignin depolymerization into low-molecular-weight aromatics. Overall, NADES pretreatment simultaneously enhances microbial lipid yields and recovers high-quality lignin, advancing the economic feasibility of renewable diesel and sustainable aviation fuel (SAF) production from bioenergy crops within an integrated biorefinery framework.

2D HSQC↗

Physics-informed machine learning to predict solvatochromic parameters of designer solvents with case studies in CO 2 and lignin dissolution

The polarity of solvents plays a critical role in various research applications, particularly in their solubilities. Polarity is conveniently characterized by the Kamlet-Taft parameters that is, the hydrogen bonding acidity (α), the basicity (β), and the polarizability (π*). Obtaining Kamlet-Taft parameters is very important for designer solvents, namely ionic liquids (ILs) and deep eutectic solvents (DESs). However, given the unlimited theoretical number of combinations of ionic pairs in ILs and hydrogen-bond donor/acceptor pairs in DESs, experimental determination of their Kamlet-Taft parameters is impractical. To address this, the present study developed two different machine learning (ML) algorithms to predict Kamlet-Taft parameters for designer solvents using quantum chemically derived input features. The ML models developed in the present study showed accurate predictions with high R 2 and low RMSE values. Further, in the context of present interest in the circular bioeconomy, the relationship between the basicities and acidities of designer solvents and their ability to dissolve lignin and carbon dioxide (CO 2 ) is discussed. Our method thus guides the design of effective solvents with optimal Kamlet-Taft parameter values dissolving and converting biomass and CO 2 into valuable chemicals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Binder jet printed WC infiltrated with pre-made melt of WC and Co

WC-Co was made via binder jet additive manufacturing of tungsten carbide followed by melt infiltration with a Co-WC infiltrant. The goal of the study was to achieve fully densified parts in near-net shape with minimal shrinkage while keeping the Co content low. The exact amount of infiltrant was determined in order to fully densify with minimum shrinkage based on the actual volume taken up by WC powder in the preform based on theoretical density, the bounding volume of prints after shrinkage, and the volume from the infiltrant. The eutectic nature of the infiltrant enabled melting at much lower temperature compared to the melting temperature of pure Co. The density, microstructure, grain size, hardness, and fracture toughness were characterized. The shrinkage and net shaping were assessed with light scans. A detailed look at the fracture mechanics was assessed. Here, this approach achieved highly dense WC-Co parts in net-shape with Co vol% of near 29 (Co wt% ~19), density of 96.2% theoretical, hardness of 8.34 GPa, grain size of 7.7 μm, magnetic saturation of 0.5 T, room temperature thermal conductivity of 125 W/mK, and fracture toughness of 24.7 = MPa·m 1/2 .

36 MATERIALS SCIENCE↗

One-pot generation of lignin microspheres and digestible substrate with a polyol-DES pretreatment in high solid loading

Previous lignin microspheres (LMS) preparation needs multiple steps with very low yield and high cost. Herein, we developed a high-solid deep eutectic solvent (DES) pretreatment for an effective lignin fractionation and enzymatic saccharification of moso bamboo under mild temperature (110 °C) with high-solid loading. Lignin was significantly removed from the plant cell wall, and cellulose properties (e.g., crystallinity and degree of polymerization) were also altered during the pretreatment. As a result, the enzymatic digestibility of the pretreated bamboo was dramatically increased. Uniform micro-spherical lignin was directly produced from the pretreatment system, and its particle size could be regulated by controlling the solid loadings and pretreatment temperatures. The lignin microspheres formation mechanism was investigated by analyzing the lignin's size distribution, molecular weight distribution, chemical structure, and hydrophobicity. The DES showed excellent recyclability, and the recycled DES could still remove 42.78% lignin even after 7th circulation associated with 100% glucan saccharification. Further, the mass balance based on 1000 g biomass showed that 196.28 g LMS was directly recovered, which exhibited a high RhB adsorption. Besides, 404.91 g glucose and 36.67 g xylose were obtained after the enzymatic saccharification process. Specifically, GAPI analysis exhibited a near total green and yellow portions of the pictogram, indicating our DES process was green enough to make this biorefinery sustainable. Overall, the proposed DES generated synergistic productions of digestible solid and LMS which could contribute to establish a green and sustainable biorefinery sequence with diverse outputs in one pot.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An x-ray absorption spectroscopy study of Mo oxidation in Pb at elevated temperatures

The corrosion of fuel cladding and structural materials by lead and lead-bismuth eutectic in the liquid state at elevated temperatures is an issue that must be considered when designing advanced nuclear systems and high-power spallation neutron targets. In this work, lead corrosion studies of molybdenum were performed to investigate the interaction layer as a function of temperature by X-ray absorption spectroscopy. In situ X-ray absorption measurements on a Mo substrate with a 3-6 {micro}m layer of Pb deposited by thermal evaporation were performed at temperatures up to 900 C and at a 15{sup o} angle to the incident X-rays. The changes in the local atomic structure of the corrosion layer are visible in the difference extended X-ray absorption fine structure and the linear combination fitting of the X-ray absorption near-edge structure to as-deposited molybdenum sample and molybdenum oxide (MoO{sub 2} and MoO{sub 3}) standards. The data are consistent with the appearance of MoO{sub 3} in an intermediate temperature range (650-800 C) and the more stable MoO{sub 2} phase dominating at high and low temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗