SEARCH · Engineering Papers

Results for “Data Collection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

All sources NASA NTRS DOE OSTI

NASA NTRSDate not supplied

An Agile-Like Approach to Hardware Development: The Ejectable Data Recorder (EDR) for Orion's Ascent Abort 2 (AA-2) Test Flight

On July 2, 2019, the Ascent Abort 2 (AA-2) Flight Test Vehicle was launched from Cape Canaveral, with the goal of demonstrating the performance of Orion’s Launch Abort System (LAS) and collecting data from hundreds of sensors throughout the vehicle. The data collected during this test flight is of paramount importance, as it will be used to certify the Orion vehicle for human spaceflight. Originally, the data was to be downlinked via a single string network of antennas on the LAS, with the associated risk of potential data dropouts, as well as loss of data once the LAS was jettisoned. Thus, additional antennas were added onto the crew module (CM) to support data downlink post-LAS jettison, a buffer rebroadcast capability was added to fill in any gaps in data downlink transmissions, and an ejectable data recorder (EDR) subsystem was added to the CM as a redundant measure to collect all the instrumentation data. The EDR subsystem was added to the project about one year after the project commenced, which significantly reduced the available development time when compared with the other subsystems of the AA-2 Test Flight. The project was further accelerated by six months, around the critical design review gate. Due to the schedule compression challenge and the fact that the EDR subsystem was a backup system and not flight critical, the EDR subsystem was further challenged to find a new and more efficient way to develop hardware. Thus, the EDR subsystem experimented with different management and systems engineering processes, team sizes, communication methods, and tools. Some examples are novel uses of SharePoint as a Data-centric Project Management & Systems Engineering environment, a continuous testing approach through the lifecycle, and a Skunkworks approach to managing the team. The EDR subsystem blended Commercial Off The Shelf (COTS) hardware with in-house developed hardware and software to create a novel data retrieval capability. The capability evolved rapidly through a hardware in the loop simulation environment that enabled incremental component updates for not only the EDR subsystem but across the entire Crew Module. This paper will present an overview of how the EDR subsystem was managed and compare it to an Agile approach to managing projects. The paper will further provide a recommended approach to future Agile-like hardware development that incorporates lessons learned from the EDR experience.

Agile↗

DOE OSTI2024

Neutron and photon in-vivo materials characterization at the evolving plasma-material interface in plasma-burning fusion environments

This report includes the first set of MOSS data collected in the context of fusion-relevant plasma-material interactions. The data collected show that the surface curvature and stress irreversibly change during low-energy deuterium ion irradiation. This holds for both tungsten thin films, bulk tungsten, and single-crystal silicon. Meanwhile, argon irradiation did not produce this same effect. The surface morphology of the exposed samples was virtually identical regardless of gas species. There were, however, some surface chemistry differences between argon-exposed and deuterium-exposed samples, mainly concerning the oxide states of the W4f XPS signal. The changes in surface chemistry could be due to hydrogen dynamics on the tungsten surfaces, though further investigation will be required with in-situ irradiation and analysis. The changes in surface stress could also not be explained by temperature alone, as the temperature reached during the ion irradiations was too low to induce non-elastic strain. With this in mind, deuterium retention in the materials could change the surface curvature and stress. To confirm this, further work will be needed to quantify the change in curvature and relate it to ion flux, fluence, and deuterium retention. Unfortunately, when this work was conducted, the experimental setup for thermal desorption spectroscopy was not operating correctly, and that work could not be included in this dissertation. Despite experimental difficulties, this work shows the first results of a promising technique to study deuterium dynamics in tungsten-based reconstituted thin films.

36 MATERIALS SCIENCE↗

NASA NTRS1988

A facility for precise temperature control applications in microgravity

The general design, main components, and operation of the isothermal dendritic growth apparatus (IDGA) designed for microgravity experimentation are described. The four major subsystems of the IDGA are a temperature controlled thermostatic bath capable of milli-kelvin stability, a photographic data collection system, a crystal growth chamber, and a growth detection system to initiate data collection. Some of the specific experiments that could utilize the capabilities of the IDGA are dendritic growth in alloys, monotectic systems, life science experiments, and technological applications.

Glicksman, M. E.↗

NASA NTRS1993

Backscatter Characteristics of the Winter Sea Ice Cover in the Beaufort

The microwave backscatter statistics of the sea ice cover in the winter Beaufort Sea were characterized using C-band Synthetic Aperture Radar (SAR) data collected by ERS-1. Sea ice backscatter signatures were sampled from SAR image data collected during the winter of 1991/92 and winter of 1992/93. The spatial and temporal variabilities of the backscatter signatures of different ice types are discussed. The results show considerable seasonal stability of the backscatter signature of multi-year ice as well as first-year ice. Small amplitude regional variations of the multi-year ice backscatter can be observed. Consistent contrast between multiyear ice and first-year ice is maintained throughout the season.

Kwok, R.↗

NASA NTRSDate not supplied

Methodology for Validation of Unsteady Pressure-Sensitive Paint Measurements using Pressure Transducers

Unsteady Pressure-Sensitive Paint (uPSP) technology provides simultaneously high-frequency and high-spatial resolution surface pressure fluctuation measurements. It has demonstrated value in wind tunnel test facilities to evaluate aerospace vehicle unsteady aerodynamics. The calibration of measurements from digital pixel counts into corresponding physical units relies on both lab-based and in-situ calibration steps, and its validation is both challenging and critical to adoption of the technology. We present a rigorous methodology for direct comparison of uPSP-derived surface pressure measurements to reference pressure transducer data based on a model of the camera-based measurement error, a model of the flow field pressure signal, and their propagation through the uPSP data reduction algorithm. The methodology is demonstrated on data collected in a small-scale, subsonic wind tunnel test as well as data collected from a Space Launch System unsteady aerodynamics characterization test at the NASA Ames Research Center Unitary Plan Wind Tunnel Complex.

Pressure-Sensitive Paint↗

NASA NTRSDate not supplied

Validating uPSP with Transducers

Pressure-Sensitive Paint↗

NASA NTRS1987

Measurement-based reliability/performability models

Measurement-based models based on real error-data collected on a multiprocessor system are described. Model development from the raw error-data to the estimation of cumulative reward is also described. A workload/reliability model is developed based on low-level error and resource usage data collected on an IBM 3081 system during its normal operation in order to evaluate the resource usage/error/recovery process in a large mainframe system. Thus, both normal and erroneous behavior of the system are modeled. The results provide an understanding of the different types of errors and recovery processes. The measured data show that the holding times in key operational and error states are not simple exponentials and that a semi-Markov process is necessary to model the system behavior. A sensitivity analysis is performed to investigate the significance of using a semi-Markov process, as opposed to a Markov process, to model the measured system.

Hsueh, Mei-Chen↗

NASA NTRS2006

Results from the Gas Chromatograph Mass Spectrometer (GCMS) Experiment on the Cassini-Huygens Probe

The GCMS was part of the instrument complement on the Cassini-Huygens Probe to measure in situ the chemical composition of the atmosphere during the probe descent and coupled with the Aerosol Collector Pyrolyser (ACP) experiment by serving as detector for the pyrolization products to determine the composition of the aerosol particles. The GCMS employed a quadrupole mass filter with a secondary electron multiplier detection system and a gas sampling system providing continuous direct atmospheric composition measurements and batch sampling through three gas chromatographic (GC) columns, a chemical scrubber and a hydrocarbon enrichment cell. The GCMS gas inlet was heated to prevent condensation, and to evaporate volatiles from the surface after impact. The GCMS collected data from an altitude of 146 km to ground impact. The Probe and the GCMS survived impact and collected data for 1 hour and 9 minutes on the surface. Mass spectra were collected during descent and on the ground over a range of m/z from 2 to 141. The major constituents of the lower atmosphere were confirmed to be NP and CH4. The methane mole fraction was uniform in the stratosphere. It increased below the tropopause, at about 32 km altitude, monotonically toward the surface, reaching a plateau at about 8 km at a level near saturation. After surface impact a steep increase of the methane signal was observed, suggesting evaporation of surface condensed methane due to heating by the GCMS sample inlet heater. The measured mole fraction of Ar-40 is 4.3 x 10(exp-5) and of Ar-36 is 2.8 x 10(exp -7). The other primordial noble gases were below mole fraction. The isotope ratios of C-12/C-13 determined from methane measurements are 82.3 and of N-14/N-15 determined from molecular nitrogen are 183. The D/H isotope ratio determined from the H2 and HD measurements is 2.3 x l0(exp -4). Carbon dioxide, ethane, acetylene and cyanogen were detected evaporating from the surface in addition to methane.

Niemann, Hasso B.↗

NASA NTRS2006

Results from the Gas Chromatograph Mass Spectrometer (GCMS) Experiment on the Cassini-Huygens Probe

The Gas Chromatograph Mass Spectrometer was one of six instruments on the Cassini-Huygens Probe mission to Titan. The GCMS measured in situ the chemical composition of the atmosphere during the probe descent and served as the detector for the pyrolization products for the Aerosol Collector Pyrolyser (ACP) experiment to determine the composition of the aerosol particles. The GCMS collected data from an altitude of 146 km to ground impact. The Probe and the GCMS survived impact and collected data for 1 hour and 9 minutes on the surface. Mass spectra were collected during descent and on the ground over a range of m/z from 2 to 141. The major constituents of the lower atmosphere were confirmed to be N2 and CH4. The methane mole fraction was uniform in the stratosphere. It increased below the tropopause, at about 32 km altitude, monotonically toward the surface, reaching a plateau at about 8 km at a level near saturation. After surface impact a steep increase of the methane signal was observed, suggesting evaporation of surface condensed methane due to heating by the GCMS sample inlet heater. The measured mole fraction of Ar-40 is 4.3x10(exp -5) and of Ar-36 is 2.8x10(exp -7). The other primordial noble gases were below 10(exp -8) mole fraction. The isotope ratios of C-12/C-13 determined from methane measurements are 82.3 and of N-14/N-15 determined from molecular nitrogen are 183. The D/H isotope ratio determined from the H2 and HD measurements is 2.3x10(exp -4). Carbon dioxide, methane, acetylene and cyanogen were detected evaporating from the surface in addition to methane. The GCMS employed a quadrupole mass filter with a secondary electron multiplier detection system and a gas sampling system providing continuous direct atmospheric composition measurements and batch sampling through three gas chromatographic (GC) columns, a chemical scrubber and a hydrocarbon enrichment cell. The GCMS gas inlet was heated to prevent condensation, and to evaporate volatiles from the surface after impact.

Niemann, H.↗

NASA NTRS2006

Results from the Gas Chromatograph Mass Spectrometer (GCMS) Experiment on the Cassini-Huygens Probe

The Gas Chromatograph Mass Spectrometer was one of six instruments on the Cassini-Huygens Probe mission to Titan. The GCMS measured in situ the chemical composition of the atmosphere during the probe descent and served as the detector for the pyrolization products for the Aerosol Collector Pyrolyser (ACP) experiment to determine the composition of the aerosol particles. The GCMS collected data from an altitude of 146 km to ground impact. The Probe and the GCMS survived impact and collected data for 1 hour and 9 minutes on the surface. Mass spectra were collected during descent and on the ground over a range of mlz from 2 to 141. The major constituents of the lower atmosphere were confirmed to be N2 and CH4. The methane mole fraction was uniform in the stratosphere. It increased below the tropopause, at about 32 km altitude, monotonically toward the surface, reaching a plateau at about 8 km at a level near saturation. After surface impact a steep increase of the methane signal was observed, suggesting evaporation of surface condensed methane due to heating by the GCMS sample inlet heater. The measured mole fraction of Ar-40 is 4.3x10(exp -5) and of Ar-36 is 2.8x10(exp -7). The other primordial noble gases were below 10(exp -8) mole fraction. The isotope ratios of C-12/C-13 determined from methane measurements are 82.3 and of N-14/N-15 determined from molecular nitrogen are 183. The D/H isotope ratio determined from the H2 and HD measurements is 2.3x10(exp -4). Carbon dioxide, ethane, acetylene and cyanogen were detected evaporating from the surface in addition to methane. The GCMS employed a quadrupole mass filter with a secondary electron multiplier detection system and a gas sampling system providing continuous direct atmospheric composition measurements and batch sampling through three gas chromatographic (GC) columns, a chemical scrubber and a hydrocarbon enrichment cell. The GCMS gas inlet was heated to prevent condensation, and to evaporate volatiles from the surface after impact.

Niemann, Hasso↗

DOE OSTI2020

Development of an MEMS ultrasonic microphone array system and its application to compressed wavefield imaging of concrete

Abstract Although contactless ultrasonic wavefield imaging shows potential for effective nondestructive inspection of various engineering materials, it has been rarely applied to concrete materials owing to technical challenges including low signal-to-noise ratio (SNR) caused by inherent heterogeneity of concrete. This paper presents development of a multi-channel MEMS ultrasonic microphone array system and its application to compressed wavefield imaging of concrete materials. The developed multi-channel MEMS ultrasonic microphone array system contains eight MEMS ultrasonic microphone elements and a signal conditioning circuit that enables measurements of ultrasonic signals with high SNR. A compressed sensing approach, based on the multiple measurement vector (MMV) concept, is applied to reconstruct a full dense ultrasonic wavefield data from sparsely sampled ultrasonic wavefield data. Experiments are carried out on a laboratory concrete sample to verify the performance of the developed MEMS microphone array system and proposed compressed sensing approach and then large-scale concrete samples to demonstrate practical application. The experimental results demonstrate that the developed MEMS microphone array system provides high-quality (SNR > 20 dB) ultrasonic data collected from concrete elements; furthermore, the proposed compressed sensing approach provides accurate reconstruction of dense wavefield data, as determined by peak signal-to-noise ratio (PSNR), from sparsely measured wavefield data with compression ratios up to 85% and PSNR above 25 dB in data collected form realistic large-scale concrete samples. By combining the MEMS array system and compressed sensing approach, the total ultrasonic data acquisition time needed to produce dense wavefield data can be significantly reduced.

Instruments & Instrumentation↗

DOE OSTI2022

The Lick Observatory Supernova Search follow-up program: photometry data release of 70 SESNe

We present BVRI and unfiltered (Clear) light curves of 70 stripped-envelope supernovae (SESNe), observed between 2003 and 2020, from the Lick Observatory Supernova Search follow-up program. Our SESN sample consists of 19 spectroscopically normal SNe Ib, 2 peculiar SNe Ib, six SNe Ibn, 14 normal SNe Ic, 1 peculiar SN Ic, 10 SNe Ic-BL, 15 SNe IIb, 1 ambiguous SN IIb/Ib/c, and 2 superluminous SNe. Our follow-up photometry has (on a per-SN basis) a mean coverage of 81 photometric points (median of 58 points) and a mean cadence of 3.6 d (median of 1.2 d). From our full sample, a subset of 38 SNe have pre-maximum coverage in at least one passband, allowing for the peak brightness of each SN in this subset to be quantitatively determined. We describe our data collection and processing techniques, with emphasis toward our automated photometry pipeline, from which we derive publicly available data products to enable and encourage further study by the community. Using these data products, we derive host-galaxy extinction values through the empirical colour evolution relationship and, for the first time, produce accurate rise-time measurements for a large sample of SESNe in both optical and infrared passbands. By modelling multiband light curves, we find that SNe Ic tend to have lower ejecta masses and lower ejecta velocities than SNe Ib and IIb, but higher 56Ni masses.

Lick Observatory↗

NASA NTRS2017

STEREO Superior Solar Conjunction Mission Phase

With its long duration and high gain antenna (HGA) feed thermal constraint; the NASA Solar-TErestrial RElations Observatory (STEREO) solar conjunction mission phase is quite unique to deep space operations. Originally designed for a two year heliocentric orbit mission to primarily study coronal mass ejection propagation, after 8 years of continuous science data collection, the twin STEREO observatories entered the solar conjunction mission phase, for which they were not designed. Nine months before entering conjunction, an unforeseen thermal constraint threatened to stop daily communications and science data collection for 15months. With a 3.5 month long communication blackout from the superior solar conjunction, without ground commands, each observatory will reset every 3 days, resulting in 35 system resets at an Earth range of 2 AU. As the observatories will be conjoined for the first time in 8 years, a unique opportunity for calibrating the same instruments on identical spacecraft will occur. As each observatory has lost redundancy, and with only a limited fidelity hardware simulator, how can the new observatory configuration be adequately and safely tested on each spacecraft? Without ground commands, how would a 3-axis stabilized spacecraft safely manage the ever accumulating system momentum without using propellant for thrusters? Could science data still be collected for the duration of the solar conjunction mission phase? Would the observatories survive? In its second extended mission, operational resources were limited at best. This paper discusses the solutions to the STEREO superior solar conjunction operational challenges, science data impact, testing, mission operations, results, and lessons learned while implementing.

STEREO↗

NASA NTRS2000

BOREAS Level-0 C-130 Navigation Data

The level-0 C-130 navigation data files contain aircraft attitude and position information acquired during the digital image and photographic data collection missions over the BOReal Ecosystem-Atmosphere Study (BOREAS) study areas. Various portions of the navigation data were collected at 1, 10, and 30 Hz. The level-0 C-130 navigation data collected for BOREAS in 1994 were improved over previous years in that the C-130 onboard navigation system was upgraded to output inertial navigation parameters every 1/30th of a second (i.e., 30 Hz). This upgrade was encouraged by users of the aircraft scanner data with the hope of improving the relative geometric positioning of the collected images.

Strub, Richard↗

NASA NTRSDate not supplied

UASs in the VOG/Edge/FOG Sensor Web Environment

This paper will describe the evolution of information collection, derivation and delivery mechanisms in sensor webs utilizing Uninhabited Aerial Systems (UAS).We will discuss the movement to "Fog Computing", also known as Edge Computing. Fog Computing facilitates the distribution of common operations and networking between edge devices and cloud computing facilities, optimizing the production of actionable intelligence. Initially, UASs utilized onboard data collection as standard, with minimal data downloaded directly. Information products were derived in conventional computational environments, generally desk top computers, and information products made available to the Science Community in weeks or months. With the increased availability, and increasingly lower costs, of beyond line of sight (BLOS) satellite based communication, transmission rates and data volumes increased, and processing migrated to Cloud based services. Contemporary UASs are moving some of that information product derivation to on vehicle services, and are creating a distributed Cloud/Fog environment. The Author will describe the technological advances that have made this possible, including low power multi-core Central Processing Units (CPU), and, more recently, the availability of high end Graphical Processing Units (GPU) that consume only a few watts. Intelligent system software, leveraging these hardware advances, finally allows for information product generation on-board, rather than simple data collection. Additionally, intelligent flight control systems now support mutual vehicle to vehicle collaboration, allowing UASs to create ad-hoc sensor webs on demand, as required. Also discussed will be the lessons learned by the Authors' development of data systems for NASA's large High Altitude Long Endurance (HALE) UASs like Predator and Global Hawk, and how those lessons are being applied to other UAS development This paper will focus on applications, rather a deep dive into the technology, and will highlight improving data management through these new technologies.

UAS↗

DOE OSTI2023

Measurement of substructure-dependent jet suppression in Pb + Pb collisions at 5.02 TeV with the ATLAS detector

The ATLAS detector at the Large Hadron Collider has been used to measure jet substructure modification and suppression in Pb + Pb collisions at a nucleon–nucleon center-of-mass energy $\sqrt{{^S}_{NN}}$ = 5.02 TeV in comparison with proton–proton (pp) collisions at $\sqrt{{^S}}$ = 5.02 TeV. The Pb + Pb data, collected in 2018, have an integrated luminosity of 1.72 nb -1 , while the pp data, collected in 2017, have an integrated luminosity of 260 pb -1 . Jets used in this analysis are clustered using the anti- k t algorithm with a radius parameter R = 0.4. The jet constituents, defined by both tracking and calorimeter information, are used to determine the angular scale r g of the first hard splitting inside the jet by reclustering them using the Cambridge–Aachen algorithm and employing the soft-drop grooming technique. The nuclear modification factor, R AA , used to characterize jet suppression in Pb + Pb collisions, is presented differentially in r g , jet transverse momentum, and in intervals of collision centrality. The R AA value is observed to depend significantly on jet r g . Jets produced with the largest measured r g are found to be twice as suppressed as those with the smallest r g in central Pb + Pb collisions. The R AA values do not exhibit a strong variation with jet p T in any of the r g intervals. The r g and p T dependence of jet R AA is qualitatively consistent with a picture of jet quenching arising from coherence and provides the most direct evidence in support of this approach.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2022

A meteorology and snow dataset from adjacent forested and meadow sites at Crested Butte, CO, USA

This dataset contains meteorology and snow observation data collected at sites in the southwestern Colorado Rocky Mountains during water years 2019-2021. Data collection had an emphasis on paired open-forest sites and included three forested elevations. In total, we present 270 snow pit observations, 4,019 snow depth measurements, and three years of meteorological forcing from two weather stations (one in a meadow, the other in an adjacent forest). The dataset is described in a forthcoming publication of the same name: A meteorology and snow dataset from adjacent forested and meadow sites at Crested Butte, CO, USA (Bonner et al., 2022).

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1973

On board satellite processing study

The use of satellite-based, world-wide data collection and location systems for scientific purposes is discussed. The configuration of satellite borne data handling equipment to prevent premature saturation and to provide maximum capacity without degradation of performance is described. An analysis of a data collection and location system based on random time and frequency access to the satellite was conducted. The subjects presented are: (1) a general description of the concept of a random access system, (2) the quantitative characteristics of random access systems, and (3) the development of a model for comparing the various types of digital communications systems.

Reed, D. L.↗