Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DUCTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

An experimental evaluation of S-duct inlet-diffuser configurations for turboprop offset gearbox applications

A test program, utilizing a large scale model, was run in the NASA Lewis Research Center 10- by 10-ft wind tunnel to examine the influence on performance of design parameters of turboprop S-duct inlet/diffuser systems. The parametric test program investigated inlet lip thickness, inlet/diffuser cross-sectional geometry, throat design Mach number, and shaft fairing shape. The test program was run at angles of attack to 15 deg and tunnel Mach numbers to 0.35. Results of the program indicate that current design techniques can be used to design inlet/diffuser systems with acceptable total pressure recovery, but several of the design parameters, notably lip thickness (contraction ratio) and shaft fairing cross section, must be optimized to prevent excessive distortion at the compressor face.

Mcdill, Paul L.↗

Ultra-light duct for an anechoic wind tunnel

A tunnel ultra-light (or TUL) is a duct composed of acoustically transparent cloth designed to transform an open-jet wind tunnel into a closed-jet wind tunnel. This concept is of interest (a priori) for anechoic wind tunnels because it improves the aerodynamic quality without hindering the measurement of sound in the far field. A full scale device designed for the 3 m diameter test section of CEPRA 19 was described. The apparatus installation did not develop any significant problems, and the mechanical support turned out to be excellent. Aerodynamic and acoustic tests are discussed. Certain imperfections in the installation as tested - instabilities above 25 m/s and acceptable cloth transmission up to 4kHz were revealed. The system as tested could eventually be used in certain applications, for example, in ground based transport. However, the concept of TUL must be developed further to arrive at a reliable mechanism for use in a large number of applications.

Lambourion, J.↗

Comparison of LDV measurements and Navier-Stokes solutions in a two-dimensional 180-degree turn-around duct

Results from an experimental and numerical investigation of turbulent subsonic flow inside a two-dimensional, strongly curved, 180 deg turn-around duct are presented. Data measured with a two-component, two-color laser Doppler velocimeter include profiles of mean axial velocity and local flow angle. Static pressure distributions are also measured. Results are obtained at a Mach number of 0.1, and at Reynolds numbers of 100,000 and a million based on channel height. Numerical calculations are performed using the incompressible Navier-Stokes equations with a Prandtl mixing length zero-equation turbulence model modified for internal flows. Theory and experiment are compared to evaluate the ability of the turbulence model to predict this class of internal flows with strong curvature.

Monson, Daryl J.↗

A study of turbulent flow computations in an angled duct with a step

This paper presents a method for effective computation of turbulent flows in an angled duct which has a step at the angled section by using a grid generation technique. An effect of flow curvature was analyzed on the separating and reattaching flows. The computations are based on the Reynolds averaged transport equations which are transformed for use on a generalized curvilinear coordinate system. A special care was taken on the treatment of pressure corrections. Wall function boundary conditions for k-epsilon model were developed.

Maruszewski, J. P.↗

Bipolar coordinates for computation of transition duct flows

Numerical simulation techniques for flows in jet-engine transition ducts with changing cross sections are developed and demonstrated. The boundary-conforming grids required are generated using bipolar coordinates, and the singularities arising at the no-slip boundaries are treated as described by de Vahl Davis (1979) and Tsai and Levy (1987). Grids for several typical configurations are employed in computations with the three-dimensional laminar/turbulent viscous-flow solver of Levy et al. (1983), and the results are presented graphically. The scheme used to deal with singularities is shown to be robust, suggesting that the bipolar grids may be applicable to Navier-Stokes computations.

Madabhushi, R. K.↗

Arc Reflector For Welding Ducts

Arc-light reflector for through-the-torch welding vision system designed expressly for use in welding ducts of small diameter. Cylindrical reflector positioned to reflect light diffusely from welding arc onto nearby surface of workpiece for most advantageous viewing along axis of welding torch.

Gilbert, Jeffrey L.↗

A probabilistic approach to the dynamic analysis of ducts subjected to multibase harmonic and random excitation

The dynamic behavior of the discharge duct of the high-pressure oxidizer turbopump of a cryogenic rocket motor is investigated analytically. The probabilistic analysis program NESSUS (Numerical Evaluation of Stochastic Structures Under Stress; Cruse et al., 1988) is used to treat the uncertainties due to random and harmonic excitation (e.g., pump noise, pump-induced harmonics, and combustion noise), variations in engine inlet pressure, and changes in system damping. The load modeling procedure, the variation in power-spectral density in different zones of the engine structure, and the dynamic structural-analysis technique are described, and the numerical results of the NESSUS analysis are presented in extensive tables and graphs and discussed in detail.

Debchaudhury, Amit↗

A rotating hot-wire technique for spatial sampling of disturbed and manipulated duct flows

A duct flow spatial sampling technique, in which an X-wire probe is rotated about the center of a cylindrical test section at a radius equal to one-half that of the test section in order to furnish nearly instantaneous multipoint measurements of the streamwise and azimuthal components, is presently evaluated in view of the control of flow disturbances downstream of various open inlet contractions. The effectiveness of a particular contraction in controlling ingested flow disturbances was ascertained by artificially introducing disturbances upstream of the contractions; control effectiveness if found to be strongly dependent on inlet contraction, with consequences for the reduction of passing-blade frequency noise during gas turbine engine ground testing.

Wark, C. E.↗

Computated Turbulent Flow In A Turnaround Duct

Kinetic energy of turbulence near wall predicted accurately. Report describes numerical simulation of two-dimensional turbulent flow in duct having 180 degree bend. Study contributes to fund of information needed to design advanced engines containing turbulent flows.

Kaul, Upender K.↗

Monograph on propagation of sound waves in curved ducts

After reviewing and evaluating the existing material on sound propagation in curved ducts without flow, it seems strange that, except for Lord Rayleigh in 1878, no book on acoustics has treated the case of wave motion in bends. This monograph reviews the available analytical and experimental material, nearly 30 papers published on this subject so far, and concisely summarizes what has been learned about the motion of sound in hard-wall and acoustically lined cylindrical bends.

Rostafinski, Wojciech↗

Design curves for circular and annular duct silencers

Conventional models of sound propagation between porous walls (Scott, 1946) are adapted in order to calculate design curves for the lined circular and annular-duct silencers used in HVAC systems. The derivation of the governing equations is outlined, and results for two typical cases are presented graphically. Good agreement with published experimental data is demonstrated.

Watson, Willie R.↗

Film condensation in a horizontal rectangular duct

Condensation heat transfer in an annular flow regime with and without interfacial waves was experimentally investigated. The study included measurements of heat transfer rate with condensation of vapor flowing inside a horizontal rectangular duct and experiments on the initiation of interfacial waves in condensation, and adiabatic air-liquid flow. An analytical model for the condensation was developed to predict condensate film thickness and heat transfer coefficients. Some conclusions drawn from the study are that the condensate film thickness was very thin (less than 0.6 mm). The average heat transfer coefficient increased with increasing the inlet vapor velocity. The local heat transfer coefficient decreased with the axial distance of the condensing surface, with the largest change at the leading edge of the test section. The interfacial shear stress, which consisted of the momentum shear stress and the adiabatic shear stress, appeared to have a significant effect on the heat transfer coefficients. In the experiment, the condensate flow along the condensing surface experienced a smooth flow, a two-dimensional wavy flow, and a three-dimensional wavy flow. In the condensation experiment, the local wave length decreased with the axial distance of the condensing surface and the average wave length decreased with increasing inlet vapor velocity, while the wave speed increased with increasing vapor velocity. The heat transfer measurements are reliable. And, the ultrasonic technique was effective for measuring the condensate film thickness when the surface was smooth or had waves of small amplitude.

Lu, Qing↗

An eddy viscosity calculation method for a turbulent duct flow

The mean velocity profile across a fully developed turbulent duct flow is obtained from an eddy viscosity relation combined with an empirical outer region wake function. Results are in good agreement with experiments and with direct numerical simulations in the same flow at two Reynolds numbers. In particular, the near-wall trend of the Reynolds shear stress and its variation with Reynolds number are similar to those of the simulations. The eddy viscosity method is more accurate than previous mixing length or implicit function methods.

Antonia, R. A.↗

Analysis of an advanced ducted propeller subsonic inlet

It is shown that a time marching Navier-Stokes code called PARC can be utilized to provide a reasonable prediction of the flow field within an inlet for an advanced ducted propeller. The code validation was implemented for a nonseparated flow condition associated with the inlet functioning at angles-of-attack of zero and 25 deg. Comparison of the computational results with the test data shows that the PARC code with the propeller face fixed flow properties boundary conditions (BC) provided a better prediction of the inlet surface static pressures than the prediction when the mass flow BC was employed.

Iek, Chanthy↗

Unsteady flowfield simulation of ducted prop-fan configurations

A technique for the simulation of unsteady flows in and around complex rotating machinery is presented. Additional domain decomposition mechanisms are introduced which extend the range of applicability of software developed for the time-accurate simulation of rotating machinery flowfields. The flow models uses the unsteady 3D Euler equations, discretized as a finite-volume method, utilizing a high-resolution approximate Riemann solver for cell interface flux definitions. Multiblock domain decomposition is used to partition the field radially, axially, as well as circumferentially into an ordered arrangement of blocks which exhibit varying degrees of similarity. A general high-order numerical scheme is applied to satisfy the geometric conservation law. Two configurations are presented - ducted single rotation prop-fan and a rotor-deswirl vane combination which form a single stage fan. Comparisons are made to other numerical solutions for these geometries and to available experimental data.

Janus, J. M.↗

Analysis of two-dimensional ducts with sudden area changes using the boundary element method

In this paper, the boundary element method (BEM) is applied to two-dimensional acoustic ducts with sudden area changes. The mathematical basis of BEM along with the technique of handling singularities is presented in a systematic manner. The computer code is verified by comparison with the exact solutions and a number of illustrative examples are included.

Pates, Carl S., III↗

Detonation duct gas generator demonstration program

An experimental demonstration is presented for the generation of detonation waves that move periodically across high speed channel flow; these waves can compress the outflow from a low pressure compressor, and thereby both reduce the compressor requirements associated with conventional gas turbines and enhance thermodynamic efficiency through isochoric energy addition. By generating transient transverse waves, rather than standing waves, shock-wave losses are reduced by an order of magnitude; the result is a Humphrey cycle augmenting the basic Brayton-cycle gas turbine. Attention is presently given to results from an experimental detonation duct.

Wortman, A.↗