Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DIFFUSION EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Creating Hydride Rim Structures in Zircaloy 4 Cladding Tubes to Mimic High Burnup

During their long service in commercial light water reactors, zirconium alloy cladding tubes are subject to oxidation and subsequent hydrogen pickup which can degrade the materials mechanical properties [1]. These degradations can lead to premature cladding ruptures during reactor power transients [2] as well as negatively impact the claddings post quench ductility following high temperature steam oxidation in thermal hydraulic transients [3]. Hydrogen has low solid solubility in zirconium and usually precipitates as brittle zirconium hydride platelets in the cladding metal matrix. Due to temperature driven diffusion (Soret effect) and the grain texture of stress relieved zirconium metal tubes, these hydrides precipitate with a circumferential orientation near the outer surface of the cladding tubes forming a hydride rim which can serve as a site for crack initiation during circumferential ‘hoop’ loading of the cladding [4rim formation][5]. In order to better understand the effect of hydride rims on the fracture behavior of stress relieved zirconium alloy cladding tubes a procedure to produce these rim-like structures is being developed at Idaho National Laboratory (INL).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Optimization design of helium circulator diffuser in HTR-PM - 18488

Circulator is very important in HTR-PM. It needs to supply enough pressure rise to circulate cooled helium in the primary loop of HTR-PM to bring heat out. Its pressure rise requirement is the highest among the worldwide circulators. Diffuser is one main component to produce pressure rise for circulator. And the most particular for HTR-PM is that the helium must flow out from two round tubes after flowing through the diffuser, which is very different from other circulators. This special export structure increases flow loss and decreases diffuser efficiency. So it is necessary to optimize diffuser to satisfy high pressure rise requirement of HTR-PM circulator with the special export structure. Four geometrical variables of diffuser have been studied and optimized. Based on the flow and performance analysis, the optimum structure was chosen. Then the detailed simulation was done by combining it with impeller to obtain performance characteristics of the whole circulator. Finally, the simulation results were compared with experimental results. It was obtained that simulation pressure rise was 201 kPa and experimental result was 210 kPa, which verified that optimization design of diffuser was effective. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

RADIATION MAGNETOHYDRODYNAMIC SIMULATIONS OF PROTOSTELLAR COLLAPSE: NONIDEAL MAGNETOHYDRODYNAMIC EFFECTS AND EARLY FORMATION OF CIRCUMSTELLAR DISKS

The transport of angular momentum by magnetic fields is a crucial physical process in the formation and evolution of stars and disks. Because the ionization degree in star-forming clouds is extremely low, nonideal magnetohydrodynamic (MHD) effects such as ambipolar diffusion and ohmic dissipation work strongly during protostellar collapse. These effects have significant impacts in the early phase of star formation as they redistribute magnetic flux and suppress angular momentum transport by magnetic fields. We perform three-dimensional nested-grid radiation magnetohydrodynamic simulations including ohmic dissipation and ambipolar diffusion. Without these effects, magnetic fields transport angular momentum so efficiently that no rotationally supported disk is formed even after the second collapse. Ohmic dissipation works only in a relatively high density region within the first core and suppresses angular momentum transport, enabling formation of a very small rotationally supported disk after the second collapse. With both ohmic dissipation and ambipolar diffusion, these effects work effectively in almost the entire region within the first core and significant magnetic flux loss occurs. As a result, a rotationally supported disk is formed even before a protostellar core forms. The size of the disk is still small, about 5 AU at the end of the first core phase, but this disk will grow later as gas accretion continues. Thus, the nonideal MHD effects can resolve the so-called magnetic braking catastrophe while keeping the disk size small in the early phase, which is implied from recent interferometric observations.

79 ASTRONOMY AND ASTROPHYSICS↗

Evolutionary models and the p-mode oscillation spectrum of Alpha Centauri A and B

Spectroscopically observed abundances of Furenlid and Meylan (1990) and Los Alamos Opacity Library opacities specifically constructed for this mixture are used to construct the most detailed models to date for Alpha Cen A and B. Models including the effects of the diffusion of helium in Alpha Cen A's interior were constructed. Although the effect of helium diffusion is small in Alpha Cen A, it is slightly larger than in the sun because of the larger mass and therefore shallower convection zone of Alpha Cen A. Keeping the heavy-element mixture unchanged but varying Z within the uncertainties yields limits to the helium abundance of Y = 0.295 and 0.305, respectively. The derived age of Alpha Cen is 4.6 +/-0.4 Gyr, very similar to the solar age of 4.5 Gyr.

Edmonds, Peter↗

A numerical study on the effect of hydrogen/reformate gas addition on flame temperature and NO formation in strained methane/air diffusion flames

This paper investigates the effects of hydrogen/reformate gas addition on flame temperature and NO formation in strained methane/air diffusion flames by numerical simulation. The results reveal that flame temperature changes due to the combined effects of adiabatic temperature, fuel Lewis number and radiation heat loss, when hydrogen/reformate gas is added to the fuel of a methane/air diffusion flame. The effect of Lewis number causes the flame temperature to increase much faster than the corresponding adiabatic equilibrium temperature when hydrogen is added, and results in a qualitatively different variation from the adiabatic equilibrium temperature as reformate gas is added. At some conditions, the addition of hydrogen results in a super-adiabatic flame temperature. The addition of hydrogen/reformate gas causes NO formation to change because of the variations in flame temperature, structure and NO formation mechanism, and the effect becomes more significant with increasing strain rate. The addition of a small amount of hydrogen or reformate gas has little effect on NO formation at low strain rates, and results in an increase in NO formation at moderate or high strain rates. However, the addition of a large amount of hydrogen increases NO formation at all strain rates, except near pure hydrogen condition. Conversely, the addition of a large amount of reformate gas results in a reduction in NO formation. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Single-crystal NMC622 from combustion-assisted solid-state synthesis: Tunable particle size, voltage-dependent stability, and Li-ion diffusion

Cost-effective and scalable synthesis of single-crystal lithium–metal-oxide cathodes with controlled size and morphology remains challenging for advancing high-performance lithium-ion batteries. Here, we demonstrate a solution combustion–assisted solid-state method for producing single-crystal NMC622 with tunable particle size at various lithium stoichiometries. Structural and electronic characteristics were probed using synchrotron-XANES, EXAFS, XRD and XPS, confirming well-defined coordination environments and phase purity up to Li ≈ 1.3. The electrochemical behavior of LixNMC (x = 1.0 and 1.3) single crystals was evaluated across 2.8–4.3 V and 2.8–4.7 V windows to elucidate the effects of lithium content and operating voltage. At 2.8–4.3V, Li1.3NMC exhibits higher initial capacity due to its larger lithium inventory, while Li1.0NMC shows superior long-term retention driven by its larger crystal size and reduced structural distortion. Increasing the cutoff voltage to 4.7 V enhances the initial capacity of both compositions by 17–25%, but long-term capacity retention ultimately converges to values comparable to those at 4.3 V due to voltage-induced degradation, where Li+ diffusion constant remains lying ranging from 10−12 –10−11 cm2s−1. Overall, this study establishes a scalable combustion-assisted route for synthesizing tunable single-crystal NMC622 and highlights the interplay between lithium stoichiometry, particle size, and voltage window in governing cathode stability.

Roy, Subrata C [Jackson State University]↗

A Self-Contained Mapping Closure Approximation for Scalar Mixing

Scalar turbulence exhibits interplays of coherent structures and random fluctuations over a broad range of spatial and temporal scales. This feature necessitates a probabilistic description of the scalar dynamics, which can be achieved comprehensively by using probability density functions (PDFs). Therefore, the challenge is to obtain the scalar PDFs (Lundgren 1967; Dopazo 1979). Generally, the evolution of a scalar is governed by three dynamical processes: advection, diffusion and reaction. In a PDF approach (Pope 1985), the advection and reaction can be treated exactly but the effect of molecular diffusion has to be modeled. It has been shown (Pope 1985) that the effect of molecular diffusion can be expressed as conditional dissipation rates or conditional diffusions. The currently used models for the conditional dissipation rates and conditional diffusions (Pope 1991) have resisted deduction from the fundamental equations and are unable to yield satisfactory results for the basic test cases of decaying scalars in isotropic turbulence, although they have achieved some success in a variety of individual cases. The recently developed mapping closure approach (Pope 1991; Chen, Chen & Kraichnan 1989; Kraichnan 1990; Klimenko & Pope 2003) provides a deductive method for conditional dissipation rates and conditional di usions, and the models obtained can successfully describe the shape relaxation of the scalar PDF from an initial double delta distribution to a Gaussian one. However, the mapping closure approach is not able to provide the rate at which the scalar evolves. The evolution rate has to be modeled. Therefore, the mapping closure approach is not closed. In this letter, we will address this problem.

He, Guo-Wei↗

On the modeling of low-Reynolds-number turbulence

A full Reynolds-stress closure that is capable of describing the flow all the way to the wall was formulated for turbulent flow through circular pipe. Since viscosity does not appear explicitly in the pressure redistribution terms, conventional high-number models for these terms are found to be applicable. However, the models for turbulent diffusion and viscous dissipation have to be modified to account for viscous diffusion near a wall. Two redistribution and two diffusion models are investigated for their effects on the model calculations. Wall correction to pressure redistribution modeling is also examined. Diffusion effects on calculated turbulent properties are further investigated by simplifying the transport equations to algebraic equations for Reynolds stress. Two approximations are explored. These are the equilibrium and nonequilibrium turbulence assumptions. Finally, the two-equation closure is also used to calculate the flow in question and the results compared with all the other model calculations. Fully developed pipe flows at two moderate Reynolds numbers are used to validate these model calculations.

So, R. M. C.↗

Effect of high rotor pressure-surface diffusion on performance of a transonic turbine

The subject turbine was investigated to determine the effect of high rotor pressure-surface diffusion on turbine performance. A comparison of the subject turbine with the most efficient transonic turbine in the present series of investigations showed that the efficiency of the subject turbine was almost as high, the suction-surface diffusion parameter was about the same, and the solidity was reduced by 36 percent. Because the loss per blade increased greatly with an increase in pressure-surface diffusion, the latter is also considered to be an important design consideration.

Miser, James W↗

Silicon solar cell process development, fabrication and analysis

For UCP Si, randomly selected wafers and wafers cut from two specific ingots were studied. For the randomly selected wafers, a moderate gettering diffusion had little effect. Moreover, an efficiency up to 14% AMI was achieved with advanced processes. For the two specific UCP ingots, ingot #5848-13C displayed severe impurity effects as shown by lower 3sc in the middle of the ingot and low CFF in the top of the ingot. Also the middle portions of this ingot responded to a series of progressively more severe gettering diffusion. Unexplained was the fact that severely gettered samples of this ingot displayed a negative light biased effect on the minority carrier diffusion length while the nongettered or moderately gettered ones had the more conventional positive light biased effect on diffusion length. On the other hand, ingot C-4-21A did not have the problem of ingot 5848-13C and behaved like to the randomly selected wafers. The top half of the ingot was shown to be slightly superior to the bottom half, but moderate gettering helped to narrow the gap.

Iles, P. A.↗

Comparison of Numerical Model Results with Diffusion Flames in Microgravity

The effects of gravity on methane diffusion flames were studied using a finite difference numerical model. Variables under consideration included velocity, pressure, temperature, enthalpy, reactive species, and inert carrier gas. Results obtained showed that flames in zero gravity were wider and taller than those in normal gravity. The use of a six reaction scheme produced similar predictions of flame width and height compared to those of the single reaction case. The numerical models predicted a considerable difference in the flame base region between normal gravity and low gravity. This region is considered to be beyond the boundaries of current analytical models.

Hyer, Paul V.↗

Mutual Diffusion Coefficients of Na 2 SO 4 at C = 0.02989 mol·dm -3 and 298.15 K by Using Rayleigh Interferometry with Free Diffusion Boundary Conditions: Experimental Test of the Effect of the C 3/2 Concentration Dependence of Refractive Index at Low Concentration

Rayleigh interferometry is one of the most precise and accurate methods for the experimental determination of the mutual diffusion coefficients of both electrolytes and non-electrolytes in liquid solutions. For binary solutions at moderate and high concentrations where the concentration dependences of both diffusion coefficient and refractive index can be assumed to be linear or almost linear and the concentration difference ΔC between a pair of solutions undergoing free diffusion is not large compared to their average concentration, and by using proper combinations of the interference fringe positions as they vary with time, under these conditions diffusion coefficients are obtained that are independent of the size of ΔC. However, this situation becomes more complicated at low concentrations for electrolyte solutions where the concentration dependences of both the diffusion coefficient and refractive index are non-linear, with C 1/2 dependence for the diffusion coefficient and C 3/2 dependence for the refractive index. As a test of these effects on calculated mutual diffusion of electrolyte solutions at low concentrations as measured by Rayleigh interferometry, apparent mutual diffusion coefficients D v,a (volume-fixed reference frame) were measured for fixed average concentrations C=(0.02989 ± 0.00001) mol·dm –3 of Na 2 SO 4 (aq) at 298.15 K while varying ΔC/C from 0.66673 to 2, a threefold variation. The dependence of the diffusion coefficient on ΔC/C was found to be linear, yielding D v = 1.041 6 × 10 –9 m 2 ·s –1 for an infinitely small concentration difference between the diffusing solutions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Zircon (U-Th)/He Impact Crater Thermochronometry and the Effects of Shock Microstructures on Helium Diffusion Kinetics

Accurate and precise age determination of impact cratering events remains challenging and often contentious; less than half of all known craters are regarded as accurately and precisely dated. Zircon (U-Th)/He (ZHe) dating of impactites can be employed to date medium to large impact structures as ZHe ages can be fully reset in minutes at T >1000°C, a plausible scenario in the central melt pool. In contrast, complete resetting of ZHe at 200-300°C, encountered near the crater margins or due to post-impact hydrothermal overprinting, may take >103-6 years. To test the reliability of ZHe impact dating, we have quantified the effects of shock-induced microstructures on helium diffusion kinetics in well-characterized variably shocked zircon. We investigated samples from two impact structures, the Chicxulub multi-ring crater and Ries complex crater, to compare diffusion kinetics from structures with different size, age, and hydrothermal system longevity. Shock microstructures were characterized by backscattered-electron imaging prior to determining the He diffusion kinetics by prograde and retrograde fractional-release experiments via light-bulb furnace with incremental step-heating (10°C) from 300°C to 600°C. Next, we examine the internal interconnectivity and sizes of the diffusion domains by EBSD. While we found that zircon with few shock microstructures exhibited no marked deviation from helium diffusion kinetics of undamaged zircon, zircon grains with planar microstructures and granular textures are characterized by a dramatic decrease in helium retentivity due to the reduction in the effective domain size and the introduction of interconnected fast diffusion pathways. A subset of grains were ZHe dated and showed that less deformed grains yielded a weighted mean age within error of the accepted impact ages, while the grains with planar microstructures or granular textures gave systematically younger ages. These new diffusion data and ZHe ages demonstrate that highly shocked grains are unsuitable for ZHe impact crater dating. Therefore, detailed characterization of impact-induced microstructures is critical for determining accurate ZHe impact ages and offers the possibility of investigating post-impact hydrothermal circulation.

Zircon↗

Understanding of the Elemental Diffusion Behavior in Concentrated Solid Solution Alloys

As one of the core effects on the high-temperature structural stability, the so-called “sluggish diffusion effect” in high-entropy alloy (HEA) has attracted much attention. Experimental investigations on the diffusion kinetics have been carried out in a few HEA systems, such as Al-Co-Cr-Fe-Ni and Co-Cr-Fe-Mn-Ni. However, the mechanisms behind this effect remain unclear. To better understand the diffusion kinetics of the HEAs, a combined computational/experimental approach is employed in the current study. In the present work, a self-consistent atomic mobility database is developed for the face-centered cubic (fcc) phase of the Co-Cr-Fe-Mn-Ni quinary system. The simulated diffusion coefficients and concentration profiles using this database can well describe the experimental data both from this work and the literatures. The validated mobility database is then used to calculate the tracer diffusion coefficients of Ni in the subsystems of the Co-Cr-Fe-Mn-Ni system with equiatomic ratios. The comparisons of these calculated diffusion coefficients reveal that the diffusion of Ni is not inevitably more sluggish with increasing number of components in the subsystem even with homologous temperature. Taking advantage of computational thermodynamics, the diffusivities of alloying elements with composition and/or temperature are also calculated. Furthermore, these calculations provide us an overall picture of the diffusion kinetics within the Co-Cr-Fe-Mn-Ni system.

36 MATERIALS SCIENCE↗

Thermal diffusion, exhaust gas recirculation and blending effects on lean premixed hydrogen flames

Thermodiffusively-unstable lean premixed hydrogen flames are investigated using two-dimensional direct numerical simulation employing finite-rate chemical kinetics. Three databases are generated focussing on the inclusion of the Soret effect, the recirculation of exhaust gas, and blending with methane. A simple rescaling of a classic thermal diffusion model is presented and shown to mimic multicomponent diffusion with very low computational cost and little-to-no loss in accuracy. It is also shown that a previously developed model for mean local flame speeds in lean premixed hydrogen flames can still be used provided Soret effects are taken into account in one-dimensional calculations. The addition of exhaust gas to the unburned mixture is found to enhance thermodiffusive instability; the primary mechanism for this was shown to be the highly-efficient third-body nature of water, with the reduction of adiabatic flame temperature a second-order effect. Again, the existing mean local flame speed model proved sufficient. Finally, blending with methane was found to reduce the thermodiffusive response of the flame, more so than the existing model suggests, despite adjustment of the fuel Lewis number; an adapted model is presented to account for this.

08 HYDROGEN↗

A mechanistic study of Soret diffusion in hydrogen-air flames

The separate and combined effects of Soret diffusion of the hydrogen molecule (H{sub 2}) and radical (H) on the structure and propagation speed of the freely-propagating planar premixed flames, and the strain-induced extinction response of premixed and nonpremixed counterflow flames, were computationally studied for hydrogen-air mixtures using a detailed reaction mechanism and transport properties. Results show that, except for the conservative freely-propagating planar flame, Soret diffusion of H{sub 2} increases the fuel concentration entering the flame structure and as such modifies the mixture stoichiometry and flame temperature, which could lead to substantial increase (decrease) of the flame speed for the lean (rich) mixtures respectively. On the other hand, Soret diffusion of H actively modifies its concentration and distribution in the reaction zone, which in turn affects the individual reaction rates. In particular, the reaction rates of the symmetric, twin, counterflow premixed flames, especially at near-extinction states, can be increased for lean flames but decreased for rich flames, whose active reaction regions are respectively located at, and away from, the stagnation surface. However, such a difference is eliminated for the single counterflow flame stabilized by an opposing cold nitrogen stream, as the active reaction zone up to the state of extinction is always located away from the stagnation surface. Finally, the reaction rate is increased in general for diffusion flames because the bell-shaped temperature distribution localizes the H concentration to the reaction region which has the maximum temperature. (author)

08 HYDROGEN↗

Simultaneous specimen current and time-dependent cathodoluminescence measurements on gallium nitride

Time-dependent cathodoluminescence (CL) and specimen current (SC) are monitored to evaluate trapping behavior and evolution of charge storage. Examination of CL and SC suggests that the near band edge emission in GaN is reduced primarily by the activation of traps upon irradiation, and Gallium vacancies are prime candidates. At the steady state, measurement of the stored charge by empiric-analytical methods suggests that all available traps within the interaction volume have been filled, and that additional charge is being stored interstitially, necessarily beyond the interaction volume. Once established, the space charge region is responsible for the steady state CL emission and, prior to build up, it is responsible for the generation of diffusion currents. Since the non-recombination effects resulting from diffusion currents that develop early on are analogous to those leading to device failure upon aging, this study is fundamental toward a holistic insight into optical properties in GaN.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗