Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Condition Monitoring”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

A New Interferometer for Monitoring Atmospheric Phase Fluctuations

Water vapor in the Earth's troposphere introduces an extra electrical path in the propagation of radio signals through the atmosphere. The distribution of water vapor is irregular and distorts the wavefronts of incoming radio waves, limiting the angular resolution that can be achieved with ground-based telescopes. The level of fluctuations depends both on the location of the site ,and on the prevailing atmospheric conditions. The ability to measure the fluctuations is therefore important when choosing a site for a new instrument, and for scheduling observations of existing telescopes. Existing phase monitors are radio interferometers that monitor monochromatic beacon tones from geostationary communications satellites at a frequency of about 12 GHz. They have a classical heterodyne design based on two satellite receiving antennas; each has a front-end for amplifying and down-converting the incoming signals using a local oscillator that is phase-locked to a common reference frequency. In addition to multiple phase-locked loops these instruments require expensive phase-stable cabling to reduce the effects of thermal drift. The new system uses two consumer 18" digital satellite TV dishes to monitor satellite TV broadcast signals over a bandwidth of 500 MHz (12.2 to 12.7 GHz). The novel design eliminates the need for phase-locked loops and thermally stable components, and uses a pair of Gilbert Cell multipliers to perform the broadband correlation. A phase monitor has been been built and deployed at the site of the Berkeley-Illinois-Maryland Association Millimeter Array in Northern California, and has been operating successfully since June 1998, measuring the difference in electrical path length for parallel lines of sight to the satellite separated by a baseline of 100 m. With a hardware cost of approximately $4000, it is much cheaper than previous instruments, and the low power requirements and high reliability make the system suitable for site testing in remote locations.

Lay, Oliver↗
NASA NTRS2008

Real-Time Implementation of Intelligent Actuator Control with a Transducer Health Monitoring Capability

This paper presents a concept of feedback control for smart actuators that are compatible with smart sensors, communication protocols, and a hierarchical Integrated System Health Management (ISHM) architecture developed by NASA s Stennis Space Center. Smart sensors and actuators typically provide functionalities such as automatic configuration, system condition awareness and self-diagnosis. Spacecraft and rocket test facilities are in the early stages of adopting these concepts. The paper presents a concept combining the IEEE 1451-based ISHM architecture with a transducer health monitoring capability to enhance the control process. A control system testbed for intelligent actuator control, with on-board ISHM capabilities, has been developed and implemented. Overviews of the IEEE 1451 standard, the smart actuator architecture, and control based on this architecture are presented.

Jethwa, Dipan↗
NASA NTRS1982

Civil helicopter propulsion system reliability and engine monitoring technology assessments

A study to reduce operating costs of helicopters, particularly directed at the maintenance of the propulsion subsystem, is presented. The tasks of the study consisted of problem definition refinement, technology solutions, diagnostic system concepts, and emergency power augmentation. Quantifiable benefits (reduced fuel consumption, on-condition engine maintenance, extended drive system overhaul periods, and longer oil change intervals) would increase the initial cost by $43,000, but the benefit of $24.46 per hour would result in breakeven at 1758 hours. Other benefits not capable of being quantified but perhaps more important include improved aircraft avilability due to reduced maintenance time, potential for increased operating limits due to continuous automatic monitoring of gages, and less time and fuel required to make engine power checks. The most important improvement is the on-condition maintenance program, which will require the development of algorithms, equipment, and procedures compatible with all operating environments.

Murphy, J. A.↗
NASA NTRSDate not supplied

Charge Deposition/Neutralization and Dust Removal via Plasma Interactions

Electrically charged and chemically reactive lunar dust can cause serious problems to spacecraft, surface equipment, and astronaut health, so understanding its interaction with and transport through the lunar plasma environment is important to dust mitigation efforts. We explore the charging of granular material in the natural environment of the Moon, recreate those conditions in the laboratory under high vacuum, and examine dust transport and charge neutralization for application in future lunar missions. Phenomena such as charge deposition via electron and ion beams, photoionization through ultraviolet light exposure, neutralization of charge through impingement by an ionized compressed gas, and tribocharging during dust liberation from surfaces will be presented. Surface materials of interest such as floating/grounded conductors and orthofabric for spacesuits are the preliminary focus of this effort. An electrometer is used to characterize currents interacting with the surfaces in the case of the electron/ion/UV source exposure, an electrostatic voltmeter is used to measure the potential on the surfaces without inadvertently discharging them, and a charge plate monitor is used to verify the efficiency of discharging the surfaces via ionized gas impingement. After setup of the initial charge conditions on the surfaces, a quick burst of high-pressure gas is used to overcome adhesion forces and initially dislodge the dust from the surfaces, followed by a low flow of gas that is ionized via application of a strong electric field. The gas is released in a high vacuum environment so as the pressure drops from the initial compressed state through to the vacuum state, the mean free path reaches a point where ionization can occur before all the gas disperses into the vacuum. This ionized gas can then neutralize both the dust and the surface to ensure minimal resettling. Several parameters such as gas composition, electrode geometry, high voltage waveform shape/polarity, and pulse timing have been explored and will be presented here.

electrostatics↗
NASA NTRSDate not supplied

An Approach for Defining IASMS Services, Functions, and Capabilities

Assuring safety in the NAS with the inclusion of new entrants, such as Advanced Air Mobility (AAM), will require overcoming unique safety challenges that result from combining innovative technologies with novel airspace concepts for moving people and cargo using autonomous vehicles. The focus of the In-time Aviation Safety Management System (IASMS) is to overcome AAM’s safety assurance challenges. The IASMS Concept of Operations (ConOps) describes an interconnected set of services, functions, and capabilities (SFCs) designed to manage operational risks, identify unknown risks, and inform system designs. This paper describes an approach for defining SFCs based on technology trends in research, assessment of known and unknown risks in voluntary safety reports, and causal and contributing factors in aviation accidents and incidents. This approach would identify potential SFCs that further expand the Monitor, Assess, and Mitigate (M-A-M) functionality that represents the enabling framework of the IASMS. Safety implications that will result from integration of AAM in the transformation of the National Airspace System (NAS) were addressed in National Academies committees reports on AAM and IASMS. Development of a ConOps for IASMS was a top recommendation and can be represented as a reframing of safety assurance that builds on real-time alerting such as the Traffic Alert and Collision Avoidance System, and adds the more encompassing in-time temporal parameter in recognition of the different timelines for collecting and assessing safety data for risk mitigations. For example, mining for safety trends from data sources such as the Aviation Safety Information Analysis and Sharing system occurs over a longer time period. Research on AAM operations poses that SFCs can be designed to monitor the safety margin appropriate for AAM including with regards to the distance between current flight parameters and nominal ideal conditions. These in-time comparisons will become more complex as the density of operations increases at least in certain areas and can include planned and actual 4D trajectory, and in-time comparisons having implications on conflict modeling and prediction including expected and actual departure time, fix/waypoint crossing times, and arrival time. These comparisons would be integrated as part of SFCs that redefine and inform new safety margin. An increased safety margin improves management of operational risks while reducing the potential for anomalies. An increased safety margin also has implications for operator confidence in the certainty of its operations and trust in automation. Technology trends in research could be used to refine existing SFCs and define needs for additional SFCs that provide safety improvements to the design and operation of vehicles, airspace design, and operator performance requirements. NASA is developing innovative approaches to safeguard against major accidents and incidents that have occurred in the NAS and those anticipated with the inclusion of envisioned AAM operations. The innovations use operational performance data to monitor, detect, and predict flight variations exceeding safe nominal patterns, such as would be caused by navigational error, severe weather complications, or hijacking of UAS controls. These innovative approaches have high potential to prevent accidents and incidents in the new AAM era. It is anticipated that elements of the innovations will evolve into SFCs for the IASMS. Voluntary safety reports can be monitored to identify anomalies related to design or operational performance risks. Reports could be periodically monitored and assessed for specific topics. Reports might serve as weak signals or precursors indicative of emergent risk such as when combined with other safety information. The architecture could include SFCs that are based on voluntary safety reports recognizing the periodic temporal nature of data analysis. As previously mentioned, aviation accidents with their causal and contributing precursors can inform the need for SFCs in the IASMS. Accidents and incidents at San Francisco International Airport such as Asiana 214 and Air Canada 759 illustrate how combinations of different factors lead to increased risk. These types of precursors and different factors have implications on the types of SFCs that could be needed to monitor and manage different sources and types of design and operational risk. Continuing to assure the safety of AAM as designs and operations gain in complexity can be accompanied by defining SFCs that also increase in complexity. These SFCs can leverage information from findings and recommendations synthesized across on-going research, voluntary safety reports, and accident and incident reports. These SFCs can serve to refine accuracy of algorithms and resolve limitations with current practices. The IASMS architecture represents the framework for the SFCs and their critical role in safety assurance.

In-Time Aviation Safety Management System↗
NASA NTRS1974

Skylab technology electrical power system

The solar array/battery power systems for the Skylab vehicle were designed to operate in a solar inertial pointing mode to provide power continuously to the Skylab. Questions of power management are considered, taking into account difficulties caused by the reduction in power system performance due to the effects of structural failure occurring during the launching process. The performance of the solar array of the Apollo Telescope Mount Power System is discussed along with the Orbital Workshop solar array performance and the Airlock Module power conditioning group performance. A list is presented of a number of items which have been identified during mission monitoring and are recommended for electrical power system concepts, designs, and operation for future spacecraft.

Woosley, A. P.↗
NASA NTRS1981

JT9D performance deterioration results from a simulated aerodynamic load test

The results of testing to identify the effects of simulated aerodynamic flight loads on JT9D engine performance are presented. The test results were also used to refine previous analytical studies on the impact of aerodynamic flight loads on performance losses. To accomplish these objectives, a JT9D-7AH engine was assembled with average production clearances and new seals as well as extensive instrumentation to monitor engine performance, case temperatures, and blade tip clearance changes. A special loading device was designed and constructed to permit application of known moments and shear forces to the engine by the use of cables placed around the flight inlet. The test was conducted in the Pratt & Whitney Aircraft X-Ray Test Facility to permit the use of X-ray techniques in conjunction with laser blade tip proximity probes to monitor important engine clearance changes. Upon completion of the test program, the test engine was disassembled, and the condition of gas path parts and final clearances were documented. The test results indicate that the engine lost 1.1 percent in thrust specific fuel consumption (TSFC), as measured under sea level static conditions, due to increased operating clearances caused by simulated flight loads. This compares with 0.9 percent predicted by the analytical model and previous study efforts.

Stakolich, E. G.↗
NASA NTRS1981

JT9D performance deterioration results from a simulated aerodynamic load test

This paper presents the results of testing to identify the effects of simulated aerodynamic flight loads on JT9D engine performance. The test results were also used to refine previous analytical studies on the impact of aerodynamic flight loads on performance losses. To accomplish these objectives, a JT9D-7AH engine was assembled with average production clearances and new seals as well as extensive instrumentation to monitor engine performance, case temperatures, and blade tip clearance changes. A special loading device was designed and constructed to permit application of known moments and shear forces to the engine by the use of cables placed around the flight inlet. The test was conducted in the Pratt and Whitney Aircraft X-Ray Test Facility to permit the use of X-ray techniques in conjunction with laser blade tip proximity probes to monitor important engine clearance changes. Upon completion of the test program, the test engine was disassembled, and the condition of gas path parts and final clearances were documented. The test results indicate that the engine lost 1.1 percent in thrust specific fuel consumption (TSFC), as measured under sea level static conditions, due to increased operating clearances caused by simulated flight loads. This compares with 0.9 percent predicted by the analytical model and previous study efforts.

Stakolich, E. G.↗
NASA NTRS1983

Effects of preprocessing Landsat MSS data on derived features

Important to the use of multitemporal Landsat MSS data for earth resources monitoring, such as agricultural inventories, is the ability to minimize the effects of varying atmospheric and satellite viewing conditions, while extracting physically meaningful features from the data. In general, the approaches to the preprocessing problem have been derived from either physical or statistical models. This paper compares three proposed algorithms; XSTAR haze correction, Color Normalization, and Multiple Acquisition Mean Level Adjustment. These techniques represent physical, statistical, and hybrid physical-statistical models, respectively. The comparisons are made in the context of three feature extraction techniques; the Tasseled Cap, the Cate Color Cube. and Normalized Difference.

Parris, T. M.↗
NASA NTRS1990

Developing a self-diagnostic system for piezoelectric sensors

Measurement techniques for developing a self-diagnostic system for piezoelectric sensors are presented. The self-diagnostic system uses two types of measurement techniques based on passive and active evaluation of the piezoelectric element. Both hard and soft failures can be detected by this system. Hard failures such as loss of sensor signal and change in sensor output resistance are determined by monitoring the sensor's output resistance, voltage or current. These are passive measurements of the sensor's output condition. Soft failures include changes in sensor calibration and mounting conditions. Soft failures are detected by measuring structural/electrical impedance of the piezoelectric sensor. Active measurement techniques are used to calculate changes in piezoelectric element properties related to soft failures. This paper describes the general operating principles of a self-diagnostic system and discusses the design of an active/passive measurement technique required for this system to function. Experimental results using two types of piezoelectric accelerometers are presented.

Flanagan, Patrick M.↗
NASA NTRS1993

Advanced Small Rocket Chambers. Basic Program and Option 2: Fundamental Processes and Material Evaluation

Propellants, chamber materials, and processes for fabrication of small high performance radiation cooled liquid rocket engines were evaluated to determine candidates for eventual demonstration in flight-type thrusters. Both storable and cryogenic propellant systems were considered. The storable propellant systems chosen for further study were nitrogen tetroxide oxidizer with either hydrazine or monomethylhydrazine as fuel. The cryogenic propellants chosen were oxygen with either hydrogen or methane as fuel. Chamber material candidates were chemical vapor deposition (CVD) rhenium protected from oxidation by CVD iridium for the chamber hot section, and film cooled wrought platinum-rhodium or regeneratively cooled stainless steel for the front end section exposed to partially reacted propellants. Laser diagnostics of the combustion products near the hot chamber surface and measurements at the surface layer were performed in a collaborative program at Sandia National Laboratories, Livermore, CA. The Material Sample Test Apparatus, a laboratory system to simulate the combustion environment in terms of gas and material temperature, composition, and pressure up to 6 Atm, was developed for these studies. Rocket engine simulator studies were conducted to evaluate the materials under simulated combustor flow conditions, in the diagnostic test chamber. These tests used the exhaust species measurement system, a device developed to monitor optically species composition and concentration in the chamber and exhaust by emission and absorption measurements.

Jassowski, Donald M.↗
NASA NTRS1994

System for the growth of bulk SiC crystals by modified CVD techniques

The goal of this program was the development of a SiC CVD growth of films thick enough to be useful as pseudo-substrates. The cold-walled CVD system was designed, assembled, and tested. Extrapolating from preliminary evaluation of SiC films grown in the system at relatively low temperatures indicates that the growth rate at the final temperatures will be high enough to make our approach practical. Modifications of the system to allow high temperature growth and cleaner growth conditions are in progress. This program was jointly funded by Wright Laboratory, Materials Directorate and NASA LeRC and monitored by NASA.

Steckl, Andrew J.↗
NASA NTRS2003

SUBSA and PFMI Transparent Furnace Systems Currently in use in the International Space Station Microgravity Science Glovebox

The Solidification Using a Baffle in Sealed Ampoules (SUBSA) and Pore Formation and Mobility Investigation (PFMI) furnaces were developed for operation in the International Space Station (ISS) Microgravity Science Glovebox (MSG). Both furnaces were launched to the ISS on STS-111, June 4, 2002, and are currently in use on orbit. The SUBSA furnace provides a maximum temperature of 850 C and can accommodate a metal sample as large as 30 cm long and 12mm in diameter. SUBSA utilizes a gradient freeze process with a minimum cooldown rate of 0.5C per min, and a stability of +/- 0.15C. An 8 cm long transparent gradient zone coupled with a Cohu 3812 camera and quartz ampoule allows for observation and video recording of the solidification process. PFMI is a Bridgman type furnace that operates at a maximum temperature of 130C and can accommodate a sample 23cm long and 10mm in diameter. Two Cohu 3812 cameras mounted 90 deg apart move on a separate translation system which allows for viewing of the sample in the transparent hot zone and gradient zone independent of the furnace translation rate and direction. Translation rates for both the cameras and furnace can be specified from 0.5micrometers/sec to 100 micrometers/sec with a stability of +/-5%. The two furnaces share a Process Control Module (PCM) which controls the furnace hardware, a Data Acquisition Pad (DaqPad) which provides signal condition of thermal couple data, and two Cohu 3812 cameras. The hardware and software allow for real time monitoring and commanding of critical process control parameters. This paper will provide a detailed explanation of the SUBSA and PFMI systems along with performance data and some preliminary results from completed on-orbit processing runs.

Spivey, Reggie A.↗
NASA NTRS2004

NASA Thermographic Inspection of Advanced Composite Materials

As the use of advanced composite materials continues to increase in the aerospace community, the need for a quantitative, rapid, in situ inspection technology has become a critical concern throughout the industry. In many applications it is necessary to monitor changes in these materials over an extended period of time to determine the effects of various load conditions. Additionally, the detection and characterization of defects such as delaminations, is of great concern. This paper will present the application of infrared thermography to characterize various composite materials and show the advantages of different heat source types. Finally, various analysis methodologies used for quantitative material property characterization will be discussed.

Cramer, K. Elliott↗
NASA NTRS1982

Automated mass spectrometer analysis system

An automated mass spectrometer analysis system is disclosed, in which samples are automatically processed in a sample processor and converted into volatilizable samples, or their characteristic volatilizable derivatives. Each volatilizable sample is sequentially volatilized and analyzed in a double focusing mass spectrometer, whose output is in the form of separate ion beams all of which are simultaneously focused in a focal plane. Each ion beam is indicative of a different sample component or different fragments of one or more sample components and the beam intensity is related to the relative abundance of the sample component. The system includes an electro-optical ion detector which automatically and simultaneously converts the ion beams, first into electron beams which in turn produce a related image which is transferred to the target of a vilicon unit. The latter converts the images into electrical signals which are supplied to a data processor, whose output is a list of the components of the analyzed sample and their abundances. The system is under the control of a master control unit, which in addition to monitoring and controlling various power sources, controls the automatic operation of the system under expected and some unexpected conditions and further protects various critical parts of the system from damage due to particularly abnormal conditions.

Kuppermann, Aron↗
NASA NTRS1978

Automated mass spectrometer analysis system

An automated mass spectrometer analysis system is disclosed, in which samples are automatically processed in a sample processor and converted into volatilizable samples, or their characteristic volatilizable derivatives. Each volatizable sample is sequentially volatilized and analyzed in a double focusing mass spectrometer, whose output is in the form of separate ion beams all of which are simultaneously focused in a focal plane. Each ion beam is indicative of a different sample component or different fragments of one or more sample components and the beam intensity is related to the relative abundance of the sample component. The system includes an electro-optical ion detector which automatically and simultaneously converts the ion beams, first into electron beams which in turn produce a related image which is transferred to the target of a vidicon unit. The latter converts the images into electrical signals which are supplied to a data processor, whose output is a list of the components of the analyzed sample and their abundances. The system is under the control of a master control unit, which in addition to monitoring and controlling various power sources, controls the automatic operation of the system under expected and some unexpected conditions and further protects various critical parts of the system from damage due to particularly abnormal conditions.

Boettger, Heinz G.↗
NASA NTRS2010

Oxidation of SiC/BN/SiC Composites in Reduced Oxygen Partial Pressures

SiC fiber-reinforced SiC composites with a BN interphase are proposed for use as leading edge structures of hypersonic vehicles. The durability of these materials under hypersonic flight conditions is therefore of interest. Thermogravimetric analysis was used to characterize the oxidation kinetics of both the constituent fibers and composite coupons at four temperatures: 816, 1149, 1343, and 1538 C (1500, 2100, 2450, and 2800 F) and in oxygen partial pressures between 5% and 0.1% (balance argon) at 1 atm total pressure. One edge of the coupons was ground off so the effects of oxygen ingress into the composite could be monitored by post-test SEM and EDS. Additional characterization of the oxidation products was conducted by XPS and TOF-SIMS. Under most conditions, the BN oxidized rapidly, leading to the formation of borosilicate glass. Rapid initial oxidation followed by volatilization of boria lead to protective oxide formation and further oxidation was slow. At 1538C in 5% oxygen, both the fibers and coupons exhibited borosilicate glass formation and bubbling. At 1538C in 0.1% oxygen, active oxidation of both the fibers and the composites was observed leading to rapid SiC degradation. BN oxidation at 1538C in 0.1% oxygen was not significant.

Opila, Elizabeth J.↗