Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Compressor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Identification of Foreign Objects Damaging Compressor Blades in Turbojet Engines

Damage to the compressor blades of turbojet engines due to ingestion of foreign objects is a growing problem, the solution of which has been made more difficult by the large percentage of damaging materials that have remained unknown. A rapid emission spectroscopic method was devised to identify the chemical composition of these foreign objects. Results on laboratory-prepared specimens and blades from damaged engines show that the method can be utilized to determine the nature of the ingested foreign objects.

Spakowski, A E↗

Investigation of Two-Stage Counterrotating Compressor. III: Design of Second-Stage Rotor and Preliminary Over-All Performance

At the design speed of a two-stage counterrotating compressor, an overall average pressure ratio of 4.3 was obtained at a specific weight flow of 27.2 pounds per second per square foot frontal area with an adiabatic efficiency of 0.75. Preliminary tests indicate that a weight-flow mismatching exists between the two rotors that causes the first rotor to operate at less than peak efficiency at design speed. At lower speeds, the first stage was forced to operate in the stalled region in single-stage tests. With the second rotor installed, no periodic rotating stall was observed, although random fluctations of similiar magnitude were noted.

Wilcox, Ward W↗

Experimental Investigation of a Five-stage Axial-flow Research Compressor with Transonic Rotors in All Stages III : Interstage Data and Individual Stage Performance Characteristics

For use in computing the detailed performance parameters of individual blade rows of a multistage compressor, radial distributions of total pressure, total temperature, static pressure and air-flow angle are tabulated. The data cover a range of air flow from choke to the approximate surge limit for equivalent rotor speeds from 70 to 100 percent of design. Equivalent stage performance curves determined from the radial survey measurements indicate both the individual performance and the matching of the stages at the speeds investigated.

Sandercock, Donald M↗

Application of radial-equilibrium condition to axial-flow compressor and turbine design

Basic general equations governing the three-dimensional compressible flow of gas through a compressor or turbine are given in terms of total enthalpy, entropy, and velocity components of the gas. Two methods of solution are obtained for the simplified, steady axially symmetric flow; one involves the use of a number of successive planes normal to the axis of the machine and short distances apart, and the other involves only three stations for a stage in which an appropriate radial-flow path is used. Methods of calculation for the limiting cases of zero and infinite blade aspect ratios and an approximate method of calculation for finite blade aspect ratio are also given. In these methods, the blade loading and the shape of the annular passage wall may be arbitrarily specified.

Wu, Chung-Hua↗

Investigation of Axial-flow Fan and Compressor Rotors Designed for Three-dimensional Flow

An investigation has been conducted to determine whether three-dimensional flows may be utilized in axial-flow fan and compressor rotors so that the spanwise load distribution may be varied to obtain high pressure rise. Two rotors, one with approximately uniform and one with solid-body downstream tangential-velocity distributions, were designed and tested at the design blade angle. Radial surveys of total pressure, static pressure, and flow angle were made upstream and downstream of the test rotors through a quantity-coefficient range. Tests of the solid-body rotor were also conducted at a large value of tip clearance. The results indicated that the three-dimensional flows may be utilized with high efficiency and that the three-dimensional theory used in conjunction with two-dimensional cascade data is sufficiently accurate for design purposes. The tests also showed that the tip-clearance losses of rotors highly loaded at the tips are not excessive. The existing three-dimensional theory in simplified for and an illustrative rotor design are presented in appendixes.

Kahane, A↗

System Measures Pressures Aboard A Compressor Rotor

Rotating pressure-measuring instrumentation includes on-board calibration standard. Computer-controlled, multichannel instrumentation system acquires pressure measurements from sensors mounted in 1.52-m-diameter rotor of compressor. Includes 5 miniature, electronically scanned pressure (ESP) modules, each containing 48 piezoresistive pressure sensors, pneumatic calibration valve, and electronic circuits for addressing and amplifying output of each sensor. Modules mounted on centerline of rotor, on instrumentation tower located inside nose cone of rotor. Subsystem designed to convert analog signal to distinct frequency without significantly affecting accuracy.

Freedman, Robert J.↗

Piston-Skirt Lubrication System For Compressor

Piston-skirt lubrication system provides steady supply of oil to piston rings of gas compressor. No need for oil-filled crankcase or external oil pump. Instead, part of each piston acts as its own oil pump circulating oil from reservoir. Annular space at bottom of piston and cylinder constitutes working volume of small oil pump. Depending on application, reservoir open to atmosphere, or sealed and pressurized in bellows to prevent contact between oil and atmosphere. Filter removes particles worn away from piston rings and cylinder wall during normal operation.

Schroeder, Edgar C.↗

Enhanced capabilities and modified users manual for axial-flow compressor conceptual design code CSPAN

Modifications made to the axial-flow compressor conceptual design code CSPAN are documented in this report. Endwall blockage and stall margin predictions were added. The loss-coefficient model was upgraded. Default correlations for rotor and stator solidity and aspect-ratio inputs and for stator-exit tangential velocity inputs were included in the code along with defaults for aerodynamic design limits. A complete description of input and output along with sample cases are included.

Glassman, Arthur J.↗

The effect of adding roughness and thickness to a transonic axial compressor rotor

The performance deterioration of a high speed axial compressor rotor due to surface roughness and airfoil thickness variations is reported. A 0.025 mm (0.001 in.) thick rough coating with a surface finish of 2.54-3.18 RMS microns (100-125 RMS microinches) is applied to the pressure and suction surface of the rotor blades. Coating both surfaces increases the leading edge thickness by 10% at the hub and 20% at the tip. Application of this coating results in a loss in efficiency of 6 points and a 9% reduction in the pressure ratio across the rotor at an operating condition near the design point. To separate the effect of thickness and roughness, a smooth coating of equal thickness is also applied to the blade. The smooth coating surface finish is 0.254-0.508 RMS microns (10-20 RMS microinches), compared to the bare metal blade surface finish of 0.508 RMS microns (20 RMS microinches). The smooth coating results in approximately half of the performance deterioration found from the rough coating. Both coatings are then applied to different portions of the blade surface to determine which portions of the airfoil are most sensitive to thickness/roughness variations. Aerodynamic performance measurements are presented for a number of coating configurations at 60%, 80%, and 100% of design speed. The results indicate that thickness/roughness over the first 10% of blade chord accounts for virtually all of the observed performance degradation for the smooth coating, compared to about 70% of the observed performance degradation for the rough coating. The performance deterioration is investigated in more detail at design speed using laser anemometer measurements as well as predictions generated by a quasi-3D Navier-Stokes flow solver which includes a surface roughness model. Measurements and analysis are performed on the baseline blade and the full-coverage smooth and rough coatings. The results indicate that coating the blade causes a thickening of the blade boundary layers. The interaction between the rotor passage shock and the thickened suction surface boundary layer then results in an increase in blockage which reduces the diffusion level in the rear half of the blade passage, thus reducing the aerodynamic performance of the rotor.

Suder, Kenneth L.↗

Experimental and Computational Investigation of the Tip Clearance Flow in a Transonic Axial Compressor Rotor

Experimental and computational techniques are used to investigate tip clearance flows in a transonic axial compressor rotor at design and part speed conditions. Laser anemometer data acquired in the endwall region are presented for operating conditions near peak efficiency and near stall at 100% design speed and at near peak efficiency at 60% design speed. The role of the passage shock/leakage vortex interaction in generating endwall blockage is discussed. As a result of the shock/vortex interaction at design speed, the radial influence of the tip clearance flow extends to 20 times the physical tip clearance height. At part speed, in the absence of the shock, the radial extent is only 5 times the tip clearance height. Both measurements and analysis indicate that under part-speed operating conditions a second vortex, which does not originate from the tip leakage flow, forms in the endwall region within the blade passage and exits the passage near midpitch. Mixing of the leakage vortex with primary flow downstream of the rotor at both design and part speed conditions is also discussed.

Suder, Kenneth L.↗

Better Gas-Gap Thermal Switches For Sorption Compressors

Gas-gap thermal switches associated with sorption compressors of some heat pumps and cryogenic systems designed for higher performance, according to proposal, by introducing controlled turbulent flows into gas gaps. Utilizes convection in turbulent flow to transfer heat at greater rate. Design takes advantage of flow of working fluid. Working fluid also serve as heat transfer medium in gas gap.

Bhandari, Pradeep↗

A packet data compressor

We are in the preliminary stages of creating an operational system for losslessly compressing packet data streams. The end goal is to reduce costs. Real world constraints include transmission in the presence of error, tradeoffs between the costs of compression and the costs of transmission and storage, and imperfect knowledge of the data streams to be transmitted. The overall method is to bring together packets of similar type, split the data into bit fields, and test a large number of compression algorithms. Preliminary results are very encouraging, typically offering compression factors substantially higher than those obtained with simpler generic byte stream compressors, such as Unix Compress and HA 0.98.

Grunes, Mitchell R.↗

Design geometry and design/off-design performance computer codes for compressors and turbines

This report summarizes some NASA Lewis (i.e., government owned) computer codes capable of being used for airbreathing propulsion system studies to determine the design geometry and to predict the design/off-design performance of compressors and turbines. These are not CFD codes; velocity-diagram energy and continuity computations are performed fore and aft of the blade rows using meanline, spanline, or streamline analyses. Losses are provided by empirical methods. Both axial-flow and radial-flow configurations are included.

Glassman, Arthur J.↗

Development of a fiber optic compressor blade sensor

A complete working prototype of the fiber optic blade tip sensor was first tested in the laboratory, followed by a thorough evaluation at NASA W8 Single Compressor Stage Facility in Lewis Research Center. Subsequently, a complete system with three parallel channels was fabricated and delivered to Dr. Kurkov. The final system was tested in the Subsonic Wind Tunnel Facility, in parallel with The General Electric Company's light probe system. The results at all operating speeds were comparable. This report provides a brief description of the system and presents a summary of the experimental results.

Dhadwal, Harbans Singh↗

Calculation of tip clearance effects in a transonic compressor rotor

The flow through the tip clearance region of a transonic compressor rotor (NASA rotor 37) was computed and compared to aerodynamic probe and laser anemometer data. Tip clearance effects were modeled both by gridding the clearance gap and by using a simple periodicity model across the ungridded gap. The simple model was run with both the full gap height, and with half the gap height to simulate a vena-contracta effect. Comparisons between computed and measured performance maps and downstream profiles were used to validate the models and to assess the effects of gap height on the simple clearance model. Recommendations were made concerning the use of the simple clearance model. Detailed comparisons were made between the gridded clearance gap solution and the laser anemometer data near the tip at two operating points. The computer results agreed fairly well with the data but overpredicted the extent of the casing separation and underpredicted the wake decay rate. The computations were then used to describe the interaction of the tip vortex, the passage shock, and the casing boundary layer.

Chima, R. V.↗

Variable-Speed Induction Motor Drives for Aircraft Environmental Control Compressors

New, more-efficient designs for aircraft jet engines are not capable of supplying the large quantities of bleed air necessary to provide pressurization and air conditioning for the environmental control systems (ECS) of the next generation of large passenger aircraft. System analysis and engineering have determined that electrically-driven ECS can help to maintain the improved fuel efficiencies; and electronic controllers and induction motors are now being developed in a NASA/NPD SBIR Program to drive both types of ECS compressors. Previous variable-speed induction motor/controller system developments and publications have primarily focused on field-oriented control, with large transient reserve power, for maximum acceleration and optimum response in actuator and robotics systems. The application area addressed herein is characterized by slowly-changing inputs and outputs, small reserve power capability for acceleration, and optimization for maximum efficiency. This paper therefore focuses on the differences between this case and the optimum response case, and shows the development of this new motor/controller approach. It starts with the creation of a new set of controller requirements. In response to those requirements, new control algorithms are being developed and implemented in an embedded computer, which is integrated into the motor controller closed loop. Buffered logic outputs are used to drive the power switches in a resonant-technology, power processor/motor-controller, at switching/resonant frequencies high enough to support efficient high-frequency induction motor operation at speeds up to 50,000-RPA

Mildice, J. W.↗