SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This report discusses the National Combustion Code (NCC). The NCC is an integrated system of codes for the design and analysis of combustion systems. The advanced features of the NCC meet designers' requirements for model accuracy and turn-around time. The fundamental features at the inception of the NCC were parallel processing and unstructured mesh. The design and performance of the NCC are discussed.
A baseline solution for CFD Point 1 (Mach 24) in the STS-107 accident investigation was modified to include effects of: (1) holes through the leading edge into a vented cavity; and (2) a scarfed, conical nozzle directed toward the centerline of the vehicle from the forward, inboard corner of the landing gear door. The simulations were generated relatively quickly and early in the investigation because simplifications were made to the leading edge cavity geometry and an existing utility to merge scarfed nozzle grid domains with structured baseline external domains was implemented. These simplifications in the breach simulations enabled: (1) a very quick grid generation procedure; and (2) high fidelity corroboration of jet physics with internal surface impingements ensuing from a breach through the leading edge, fully coupled to the external shock layer flow at flight conditions. These simulations provided early evidence that the flow through a two-inch diameter (or larger) breach enters the cavity with significant retention of external flow directionality. A normal jet directed into the cavity was not an appropriate model for these conditions at CFD Point 1 (Mach 24). The breach diameters were of the same order or larger than the local, external boundary-layer thickness. High impingement heating and pressures on the downstream lip of the breach were computed. It is likely that hole shape would evolve as a slot cut in the direction of the external streamlines. In the case of the six-inch diameter breach the boundary layer is fully ingested. The intent of externally directed jet simulations in the second scenario was to approximately model aerodynamic effects of a relatively large internal wing pressure, fueled by combusting aluminum, which deforms the corner of the landing gear door and directs a jet across the windside surface. These jet interactions, in and of themselves, were not sufficiently large to explain observed aerodynamic behavior.
Understanding the radiative forcing caused by anthropogenic aerosol sources is essential for making effective emission control decisions to mitigate climate change. We examined the net direct plus indirect radiative forcing caused by carbonaceous aerosol and sulfur emissions in key sectors of China and India using the GISS-E2 chemistry-climate model. Diesel trucks and buses (67 mW/ sq. m) and residential biofuel combustion (52 mW/ sq. m) in India have the largest global mean, annual average forcings due mainly to the direct and indirect effects of BC. Emissions from these two sectors in China have near-zero net global forcings. Coal-fired power plants in both countries exert a negative forcing of about -30 mW/ sq. m from production of sulfate. Aerosol forcings are largest locally, with direct forcings due to residential biofuel combustion of 580 mW/ sq. m over India and 416 mW/ sq. m over China, but they extend as far as North America, Europe, and the Arctic
NASA’s plans for landing human-scale payloads on Mars in the next decade require that retrorockets be used to decelerate the atmospheric entry vehicle continuously from supersonic conditions through soft touchdown. Conventional Mars entry vehicle architectures that include a single parachute for supersonic-to-subsonic descent are not scalable to the sizes needed to land humans on Mars (~20 metric tons). The major aerosciences risks are the uncertainties in predicting aerodynamic stability and performance during powered free-flight and landing. These risks are influenced partially by current limitations in relevant data and testing methods. Consequently, trajectory simulations currently depend on unvalidated powered descent and landing aerodynamics models. NASA engineers have identified gaps in testing methods that, if addressed, would improve the ability to validate these models. There are gaps in capabilities to test multi-engine hot-gas retropropulsion systems in US wind tunnels. This is partially due to the successful use of parachutes as decelerators for human spaceflight at Earth and for the entire Mars lander program to date. Retropulsion test data historically and to this day are limited to using high pressure air jets, at comparatively low temperatures,as engine plume simulants on subscale wind tunnel models. Additionally, the ability to directly measure aerodynamic interference force and moments is limited by existing flow-through balance capabilities. This paper briefly covers historical and recent test data, and identifies new ground test techniques as a means to provide more relevant test data for powered flight and landing aerodynamic model validation.These techniques include using heated inert gases as a substitute for combustion products, additively manufactured 6-component flow-through force and moment balances, and off-body quantitative diagnostic measurements.
This is the sixth yearly report on the research at Princeton University on the problem of combustion instability in liquid-propellant rocket motors. These investigations have been sponsored by the National Aeronautics and Space Administration under NASA Contract NASr-217 and, in the past, under NASA Grant NsG-99-60. The nonlinear aspects of the problem have been emphasized in both the theoretical and experimental portions of the program. Presently, the theoretical research primarily involves studies of possible mechanisms or forcing functions of the instabilities, the nonlinear gasdynamic oscillations associated with instability in rocket motors, the effect of the exhaust nozzle on the stability, and the effect of damping devices on the stability. In conjunction with the theoretical program, an experimental program of an equally broad range is being conducted. This program includes basic experiments both with rocket motors and "cold" chambers which have been designed to study various combustion processes in order to provide understanding which would be useful in the construction of a theoretical model. It also includes studies of the effects of exhaust nozzles and damping devices upon the instability as well as controlled testing of liquid rocket motors with parametric variations intended to determine the factors which strongly influence the incidence of nonlinear combustion instability.
Injector geometry, physical mixing, chemical processes, and engine cycle conditions together govern performance, operability and emission characteristics of aviation gas-turbine combustion systems. The present investigation explores swirl-venturi lean direct injection combustor fundamentals, characterizing the influence of key geometric injector parameters on reacting flow physics and emission production trends. In this computational study, a design space exploration was performed using a parameterized swirl-venturi lean direct injector model. From the parametric geometry, 20 three-element lean direct injection combustor sectors were produced and simulated using steady-state, Reynolds-averaged Navier-Stokes reacting computations. Species concentrations were solved directly using a reduced 18-step reaction mechanism for Jet-A. Turbulence closure was obtained using a nonlinear κ-ε model. Results demonstrate sensitivities of the geometric perturbations on axially averaged flow field responses. Output variables include axial velocity, turbulent kinetic energy, static temperature, fuel patternation and minor species mass fractions. Significant trends have been reduced to surrogate model approximations, intended to guide future injector design trade studies and advance aviation gas-turbine combustion research.
This volume, the first of two volumes is a compilation of 59 unclassified/unlimited-distribution technical papers presented at the Joint Army-Navy-NASA-Air Force (JANNAF) 37th Combustion Subcommittee (CS) meeting held jointly with the 25th Airbreathing Propulsion Subcommittee (APS), 19th Propulsion Systems Hazards Subcommittee (PSHS), and 1st Modeling and Simulation Subcommittee (MSS) meetings. The meeting was held 13-17 November 2000 at the Naval Postgraduate School and Hyatt Regency Hotel, Monterey, California. Topics covered at the CS meeting include: a keynote address on the Future Combat Systems, and review of a new JANNAF Modeling and Simulation Subcommittee, and technical papers on gun propellant burning rate, gun tube erosion, advanced gun propulsion concepts, ETC guns, novel gun propellants; liquid, hybrid and novel propellant combustion; solid propellant combustion kinetics, GAP, ADN and RDX combustion, sandwich combustion, metal combustion, combustion instability, and motor combustion instability.
Turbulent nonreactive and reactive flows with and without swirl are analyzed, with particular attention given to the flow fields of a gas-fueled nonpremixed swirl-stabilized combustor and a premixed opposed-jet combustor. Local mean flow properties, including velocity, temperature, and major species concentrations, are calculated by solving numerically the governing partial differential equations with associated submodels for turbulence and combustion. The results of the study indicate that the constant-density k-epsilon turbulence model provides a satisfactory representation of the aerodynamics in most practical combustor flows. The exception is the case of jet-stabilized combustor flow, due to the fact that the k-epsilon model cannot replicate the highly dissipative phenomenon found in such flows.
Possible mechanisms for compressive ignition of liquid monopropellants are discussed. These mechanisms all involve the collapse of a gas filled bubble imbedded in the liquid. A model of the collapse of a gas bubble in an incompressible liquid and the combustion of the surrounding liquid after ignition occurs is presented. The effect of gas covolume, liquid density, the adiabatic exponent, rate of pressurization and prepressurization are investigated. Calculations for finite and infinite liquid volumes are also presented. Gas generation in the bubble is shown to have a significant effect on its evolution and the introduction of a surface enhancement factor leads to a runaway reaction. For the conditions considered, the reacting bubble oscillates at a frequency of about 35 kHz over the first 0.5 milliseconds. This frequency decreases as the surface enhancement factor is increased. The implication is that a one dimensional model of this process may be tractable from the standpoint of computer time.
A hypersonic wind tunnel test method for obtaining credible aerodynamic data on a complete hypersonic vehicle (generic X-24c) with scramjet exhaust flow simulation is described. The general problems of simulating the scramjet exhaust as well as accounting for scramjet inlet flow and vehicle forces are analyzed, and candidate test methods are described and compared. The method selected as most useful makes use of a thrust-minus-drag flow-through balance with a completely metric model. Inlet flow is diverted by a fairing. The incremental effect of the fairing is determined in the testing of two reference models. The net thrust of the scramjet module is an input to be determined in large-scale module tests with scramjet combustion. Force accounting is described, and examples of force component levels are predicted. Compatibility of the test method with candidate wind tunnel facilities is described, and a preliminary model mechanical arrangement drawing is presented. The balance design and performance requirements are described in a detailed specification. Calibration procedures, model instrumentation, and a test plan for the model are outlined.
Partially premixed combustion is an intermediate regime between the limiting cases of premixed and nonpremixed combustion. Although combustion problems are generally approached from one of these two limiting cases, there are many practical situations where flames cannot be considered as purely premixed or nonpremixed, and thus the partially premixed approach must be used. In partially premixed combustion, mechanisms from the premixed and nonpremixed regimes can coexist, and as a result some interesting new phenomena can arise. One such phenomenon is the flame stabilization in laminar mixing layers by triple flames. One of the first observations of triple flames was made by Phillips (1965), who investigated a triple flame propagating in a methane mixing layer. Kioni et al. (1993) also examined triple flames both experimentally and numerically. There have also been numerous analytical studies on the shape and propagation of triple flames under various assumptions by Dold (1989), Dold et al. (1991), and Hartley and Dold (1991). In terms of modeling, Muller et al. (1994) have combined the flamelet formulations for premixed and nonpremixed combustion in order to treat lifted diffusion flames. One common feature in the analytical and numerical studies mentioned above is the assumption of zero heat release, which is necessary to make the problem tractable. The effect of heat release on triple flames was investigated by Ruetsch et al. (1995), where for the unconfined case, flame speeds larger than their premixed counterparts were found. One of the most important practical situations in which these conditions arise is in lifted turbulent jet diffusion flames. At a critical velocity the burning zone of a fuel jet lifts off from the nozzle, moves to increasing distances as the jet velocity increases, and finally blows off. The mechanisms that control these phenomena, i.e. that determine the stability of these flames, are still not understood. In addition to regions where diffusion flame stabilization takes place, partially premixed conditions also exist during the ignition process in nonpremixed systems. Numerical simulations by Reveillon et al. (1994) of the ignition process in a weakly stirred mixture of fuel and oxidizer show that triple flames propagate along lines of stoichiometric mixture fraction throughout the fluid. In addition, Peters (1994) notes that NO(x) emissions are likely to be large in such transient cases, and therefore an understanding of triple flames can provide information concerning pollutant formation. This study extends the work previously done and examines the effects of lateral confinement on partially premixed flames. Once again, we study both the flame structure and propagation.
This report gives an overview of physical modeling enhancements to the Wind-US flow solver which were made to improve the capabilities for simulation of hypersonic flows and the reliability of computations to complement hypersonic testing. The improvements include advanced turbulence models, a bypass transition model, a conjugate (or closely coupled to vehicle structure) conduction-convection heat transfer capability, and an upgraded high-speed combustion solver. A Mach 5 shock-wave boundary layer interaction problem is used to investigate the benefits of k- s and k-w based explicit algebraic stress turbulence models relative to linear two-equation models. The bypass transition model is validated using data from experiments for incompressible boundary layers and a Mach 7.9 cone flow. The conjugate heat transfer method is validated for a test case involving reacting H2-O2 rocket exhaust over cooled calorimeter panels. A dual-mode scramjet configuration is investigated using both a simplified 1-step kinetics mechanism and an 8-step mechanism. Additionally, variations in the turbulent Prandtl and Schmidt numbers are considered for this scramjet configuration.
This is the final report for a research project aimed at developing planar laser-induced fluorescence (PLIF) techniques for quantitative 2-D species imaging in fuel-lean, high-pressure combustion gases, relevant to modem aircraft gas turbine combustors. The program involved both theory and experiment. The theoretical activity led to spectroscopic models that allow calculation of the laser-induced fluorescence produced in OH, NO and 02 for arbitrary excitation wavelength, pressure, temperature, gas mixture and laser linewidth. These spectroscopic models incorporate new information on line- broadening, energy transfer and electronic quench rates. Extensive calculations have been made with these models in order to identify optimum excitation strategies, particularly for detecting low levels (ppm) of NO in the presence of large 02 mole fractions (10% is typical for the fuel-lean combustion of interest). A promising new measurement concept has emerged from these calculations, namely that excitation at specific wavelengths, together with detection of fluorescence in multiple spectral bands, promises to enable simultaneous detection of both NO (at ppm levels) and 02 or possibly NO, 02 and temperature. Calculations have been made to evaluate the expected performance of such a diagnostic for a variety of conditions and choices of excitation and detection wavelengths. The experimental effort began with assembly of a new high-pressure combustor to provide controlled high-temperature and high-pressure combustion products. The non-premixed burner enables access to postflame gases at high temperatures (to 2000 K) and high pressures (to 13 atm), and a range of fuel-air equivalence ratios. The chamber also allowed use of a sampling probe, for chemiluminescent detection of NO/NO2, and thermocouples for measurement of gas temperature. Experiments were conducted to confirm the spectroscopic models for OH, NO and 02.
In this report, we present some results of problems investigated during joint research between the Hampton University Fluid Mechanics and Acoustics Laboratory (HU/FM&AL), NASA GRC, and the LaRC Hyper-X Program. This work is supported by joint research between the NASA GRC and the Institute of Mechanics at Moscow State University (IM/MSU) in Russia under a CRDF grant. The main areas of current scientific interest of the HU/FM&AL include an investigation of the proposed and patented advanced methods for aircraft engine thrust and noise benefits. These methods are based on nontraditional 3D corrugated and composite nozzle, inlet, propeller and screw designs such as a Bluebell and Telescope nozzle, Mobius-shaped screw, etc. This is the main subject of our other projects, of which one is presented at the current conference. Here we analyze additional methods for exhaust jet noise reduction without essential thrust loss and even with thrust augmentation. Such additional approaches are: (1) to add some solid, fluid, or gas mass at discrete locations to the main supersonic gas stream to minimize the negative influence of strong shock waves formed in propulsion systems. This mass addition may be accompanied by heat addition to the main stream as a result of the fuel combustion or by cooling of this stream as a result of the liquid mass evaporation and boiling; (2) Use of porous or permeable nozzles and additional shells at the nozzle exit for preliminary cooling of the hot jet exhaust and pressure compensation for off-design conditions (so-called continuous ejector with small mass flow rate); and (3) to propose and analyze new effective methods of fuel injection into the flow stream in air-breathing engines. The research is focused on a wide regime of problems in the propulsion field as well as in experimental testing and theoretical and numerical simulation analyses for advanced aircraft and rocket engines. The FM&AL Team uses analytical methods, numerical simulations, and experimental tests at the Hampton University campus, NASA, and IM/MSU. The main outcomes during this reporting period are: (1) Publications: The AIAA Paper #01-1893 has been accepted for the AIAA/NAL-NASDA-ISAS 10th International Space Planes and Hypersonic Systems and Technologies Conference, 24-27 April 2001, Kyoto, Japan. The AIAA Paper #01-3204 has been accepted for presentation at the 37th AIAA/ASME/SAE/ASEE Joint Propulsion Conference being held on 08-11 July, in Salt Lake City, UT; (2) Grants and proposals: The HU/FM&AL was awarded the NASA grant NAG3-2495 in October 2000 and the CRDF award was granted to the NASA GRC-HU FM&AL and IM/MSU (Russia) in July 2000. A solicited proposal was submitted for the NASA NRA-01GRC-02 competition and two unsolicited proposals to NASA are in preparation; (3) Theory and numerical simulations: Analytical theory, numerical simulation, comparison of theoretical with experimental results, and modification of theoretical approaches, models, grids, etc. Such investigations have been conducted for three main problems: (a) Combustion efficiency optimization in the half-duct combustor system; (b) Drag reduction effects for blunt bodies with solid needles; and (c) Solid particle injection from the butt-end against a supersonic flow. The NASA CFL3D, HU/FM&AL, and IM/MSU GODUNOV codes were used and modified for solution of these problems. The codes are based on full Euler and Navier-Stokes solvers with and without nonequilibrium oxygen-nitrogen and air-hydrogen chemical reactions in laminar and turbulent gas flow regimes; (4) Experimental tests: In the IM/MSU supersonic wind tunnel, experimental tests were conducted with different number, location, and geometric parameters of solid needles mounted at the front of the butt-end in supersonic flow. Optimal parameters were determined that provide minimal butt-end drag in the stationary flow regime. Experimental and numerical simulation results are in good agreement; (5) Student Research Activity: Involvement of one graduate and two undergraduate students as research assistants in the current project.
Feedforward neural networks were used to model three parameters during the Space Shuttle Main Engine startup transient. The three parameters were the main combustion chamber pressure, a controlled parameter, the high pressure oxidizer turbine discharge temperature, a redlined parameter, and the high pressure fuel pump discharge pressure, a failure-indicating performance parameter. Network inputs consisted of time windows of data from engine measurements that correlated highly to the modeled parameter. A standard backpropagation algorithm was used to train the feedforward networks on two nominal firings. Each trained network was validated with four additional nominal firings. For all three parameters, the neural networks were able to accurately predict the data in the validation sets as well as the training set.
Feedforward neural networks were used to model three parameters during the Space Shuttle Main Engine startup transient. The three parameters were the main combustion chamber pressure, a controlled parameter, the high pressure oxidizer turbine discharge temperature, a redlined parameter, and the high pressure fuel pump discharge pressure, a failure-indicating performance parameter. Network inputs consisted of time windows of data from engine measurements that correlated highly to the modeled parameter. A standard backpropagation algorithm was used to train the feedforward networks on two nominal firings. Each trained network was validated with four additional nominal firings. For all three parameters, the neural networks were able to accurately predict the data in the validation sets as well as the training set.
An analytical model of the Space Shuttle Main Engine (SSME) called SSME Streamtube Evaluation Program (SSTEP) has been developed based upon the assumption that the propellant flows through the main combustion chamber can be represented by a bundle of parallel streamtubes. The motivation for the development of SSTEP lies in the desire to gain a basic understanding of the engine performance effects of several common SSME hardware modifications. Specifically, this model has been used to evaluate the changes in performance due to boundary layer coolant hole enlargement, LOX post plugging, acoustic cavity elimination, baffle removal, and main combustion chamber coolant leakage. The results show a good general agreement with the available test data suggesting at least a qualitative agreement between SSTEP modeling and actual engine performance. Through the use of several adjustment factors, which represent relaxations of the SSTEP formulation assumptions, it is shown that the test data can be very closely matched and that SSTEP can be used as a performance prediction tool.
A time-dependent model is presented which simulates the essential physics of a detonative or otherwise constant volume, pressure-gain combustor for gas turbine applications. The model utilizes simple, global thermodynamic relations to determine an assumed instantaneous and uniform post-combustion state in one of many envisioned tubes comprising the device. A simple, second order, non-upwinding computational fluid dynamic algorithm is then used to compute the (continuous) flowfield properties during the blowdown and refill stages of the periodic cycle which each tube undergoes. The exhausted flow is averaged to provide mixed total pressure and enthalpy which may be used as a cycle performance metric for benefits analysis. The simplicity of the model allows for nearly instantaneous results when implemented on a personal computer. The results compare favorably with higher resolution numerical codes which are more difficult to configure, and more time consuming to operate.