Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CARRIER MODULATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Melt-Centrifuged (Bi,Sb) 2 Te 3 : Engineering Microstructure toward High Thermoelectric Efficiency

Microstructure engineering is an effective strategy to reduce lattice thermal conductivity (JG) and enhance the thermoelectric figure of merit (zT). Through a new process based on melt-centrifugation to squeeze out excess eutectic liquid, microstructure modulation is realized to manipulate the formation of dislocations and clean grain boundaries, resulting in a porous network with a platelet structure. In this way, phonon transport is strongly disrupted by a combination of porosity, pore surfaces/junctions, grain boundaries, and lattice dislocations. These collectively result in a ≈60% reduction of JG compared to zone melted ingot, while the charge carriers remain relatively mobile across the liquid-fused grains. This porous mate­rial displays a zT value of 1.2, which is higher than fully dense conventional zone melted ingots and hot pressed (Bi,Sb) 2 Te 3 alloys. A segmented leg of melt-centrifuged Bi 0.5 Sb 1.5 Te 3 and Bi 0.3 Sb 1.7 Te 3 could produce a high device ZT exceeding 1.0 over the whole temperature range of 323-523 K and an efficiency up to 9%. Here, we demonstrate a method for synthe­sizing high-efficiency porous thermoelectric materials through an uncon­ventional melt-centrifugation technique.

36 MATERIALS SCIENCE↗
NASA NTRS2002

Center for Space Telemetering and Telecommunications Systems, New Mexico State University

This viewgraph presentation gives an overview of the Center for Space Telemetering and Telecommunications Systems activities at New Mexico State University. Presentations cover the following topics: (1) small satellite communications, including nanosatellite radio and virtual satellite development; (2) modulation and detection studies, including details on smooth phase interpolated keying (SPIK) spectra and highlights of an adaptive turbo multiuser detector; (3) decoupled approaches to nonlinear ISI compensation; (4) space internet testing; (4) optical communication; (5) Linux-based receiver for lightweight optical communications without a laser in space, including software design, performance analysis, and the receiver algorithm; (6) carrier tracking hardware; and (7) subband transforms for adaptive direct sequence spread spectrum receivers.

Horan, Stephen↗
DOE OSTI2022

Unusual electronic transport in (1 - x )Cu 2 Se-( x )CuInSe 2 hierarchical composites

The ability to control the relative density of electronic point defects as well as their energy distribution in semiconductors could afford a systematic modulation of their electronic, optical, and optoelectronic properties. Using a model binary hybrid system Cu 2 Se–CuInSe 2 , we have investigated the correlation between phase composition, microstructure, and electronic transport behavior in the synthesized composites. We found that both Cu 2 Se and CuInSe 2 phases coexist at multiple length scales, ranging from sub-ten nanometer to several micrometers, leading to the formation of a hybrid hierarchical microstructure. Astonishingly, the electronic phase diagram of the (1 - x)Cu 2 Se–(x)CuInSe 2 (15% ≤ x ≤ 100%) hierarchical composites remarkably deviates from the trend normally expected for composites between a heavily doped semiconductor (Cu 2 Se) and a poorly conducting phase (CuInSe 2 ). A sudden 3-fold increase in the electrical conductivity and carrier concentration along with a marginal increase in the carrier mobility is observed for composites at the vicinity of equimolar composition (48% ≤ x ≤ 52%). The carrier concentration increases from ~1.5 × 10 20 cm -3 for the composites with x ≤ 45% to 5.0 × 10 20 cm -3 for x = 50%, and remains constant at 4.5 × 10 20 cm -3 with x value in the range of 52% < x ≤ 90%, then quickly drops to 8 × 10 18 cm -3 for pristine CuInSe 2 phase (x = 100%). The atypical electronic behavior was rationalized in the light of the formation of an inter-band (IB) within the band gap, which arises from the hybridization of native electronic point defects from both Cu 2 Se and CuInSe 2 phases in the resulting hierarchical composites. The result points to a new strategy to modulate the electronic structure of semiconductor composites to maximize interaction and coupling between two fundamentally contrasting properties enabling access to electronic hybrid systems with potential applications as interactive and stimuli-responsive multifunctional materials.

36 MATERIALS SCIENCE↗
NASA NTRS1985

A sequential decoding performance analysis for International Comet Explorer

The effect of a noisy reference carrier on the performance of International Comet Explorer (ICE) Sequential decoder is analyzed. Ideal reference models for frame deletion probability are given for the Telemetry Processing Assembly (TPA) and the Linkabit (LS4815) sequential decoders. Based on these ideal reference models the deletion probability in the presence of noisy reference carrier is computed for both the high and the low data rate cases. A medium data rate performance model is then derived using an interpolation method. The derived medium rate performance model depends on the phase locked loop bandwidth-integration time product. Results are obtained for frame length 1024 bits, data bit rates of 1024 bps and 512 bps, modulation index of 60 deg, and threshold loop bandwidths of 10 Hz and 3 Hz. The medium rate model agrees with experimental data to within measurement uncertainty. For the 10 Hz loop bandwidth and modulation index of 60 deg at frame deletion rate of 0.0001, the required total received power to noise ratio is 36 dB. The analysis given is general and applicable to any sequential decoder, provided that the ideal reference model of the decoder is available.

Divsalar, D.↗
NASA NTRS1985

Simulation analysis of a novel high efficiency silicon solar cell

It is recognized that crystalline silicon photovoltaic module efficiency of 15 percent or more is required for cost-effective photovoltaic energy utilization. This level of module efficiency requires large-area encapsulated production cell efficiencies in the range of 18 to 20 percent. Though the theoretical maximum of silicon solar cell efficiency for an idealized case is estimated to be around 30 percent, practical performance of cells to-date are considerably below this limit. This is understood to be largely a consequence of minority carrier losses in the bulk as well as at all surfaces including those under the metal contacts. In this paper a novel device design with special features to reduce bulk and surface recombination losses is evaluated using numerical analysis technique. Details of the numerical model, cell design, and analysis results are presented.

Mokashi, Anant R.↗
NASA NTRS1995

Product Assurance for Spaceflight Hardware

This report contains information about the tasks I have completed and the valuable experience I have gained at NASA. The report is divided into two different sections followed by a program summary sheet. The first section describes the two reports I have completed for the Office of Mission Assurance (OMA). I describe the approach and the resources and facilities used to complete each report. The second section describes my experience working in the Receipt Inspection/Quality Assurance Lab (RI/QA). The first report described is a Product Assurance Plan for the Gas Permeable Polymer Materials (GPPM) mission. The purpose of the Product Assurance Plan is to define the various requirements which are to be met through completion of the GPPM mission. The GPPM experiment is a space payload which will be flown in the shuttle's SPACEHAB module. The experiment will use microgravity to enable production of complex polymeric gas permeable materials. The second report described in the first section is a Fracture Analysis for the Mir Environmental Effects Payload (MEEP). The Fracture Analysis report is a summary of the fracture control classifications for all structural elements of the MEEP. The MEEP hardware consists of four experiment carriers, each of which contains an experiment container holding a passive experiment. The MEEP hardware will be attached to the cargo bay of the space shuttle. It will be transferred by Extravehicular Activity and mounted on the Mir space station. The second section of this report describes my experiences in the RVQA lab. I listed the different equipment I used at the lab and their functions. I described the extensive inspection process that must be completed for spaceflight hardware. Included, at the end of this section, are pictures of most of the equipment used in the lab. There is a summary sheet located at the end of this report. It briefly describes the valuable experience I have gained at NASA this summer and what I will be able to take with me as I return to college. I briefly discuss the experiences I mentioned in the previous three paragraphs along with training classes I attended and courses I completed at the Learning Lab.

Monroe, Mike↗
NASA NTRS2007

Smooth Phase Interpolated Keying

Smooth phase interpolated keying (SPIK) is an improved method of computing smooth phase-modulation waveforms for radio communication systems that convey digital information. SPIK is applicable to a variety of phase-shift-keying (PSK) modulation schemes, including quaternary PSK (QPSK), octonary PSK (8PSK), and 16PSK. In comparison with a related prior method, SPIK offers advantages of better performance and less complexity of implementation. In a PSK scheme, the underlying information waveform that one seeks to convey consists of discrete rectangular steps, but the spectral width of such a waveform is excessive for practical radio communication. Therefore, the problem is to smooth the step phase waveform in such a manner as to maintain power and bandwidth efficiency without incurring an unacceptably large error rate and without introducing undesired variations in the amplitude of the affected radio signal. Although the ideal constellation of PSK phasor points does not cause amplitude variations, filtering of the modulation waveform (in which, typically, a rectangular pulse is converted to a square-root raised cosine pulse) causes amplitude fluctuations. If a power-efficient nonlinear amplifier is used in the radio communication system, the fluctuating-amplitude signal can undergo significant spectral regrowth, thus compromising the bandwidth efficiency of the system. In the related prior method, one seeks to solve the problem in a procedure that comprises two major steps: phase-value generation and phase interpolation. SPIK follows the two-step approach of the related prior method, but the details of the steps are different. In the phase-value-generation step, the phase values of symbols in the PSK constellation are determined by a phase function that is said to be maximally smooth and that is chosen to minimize the spectral spread of the modulated signal. In this step, the constellation is divided into two groups by assigning, to information symbols, phase values that result in equal numbers of clockwise and counter-clockwise phase rotations for equally likely symbols. The purpose served by assigning phase values in this way is to prevent unnecessary generation of spectral lines and prevent net shifts of the carrier signal. In the phase-interpolation step, the smooth phase values are interpolated over a number, n, of consecutive symbols (including the present symbol) by means of an unconventional spline curve fit.

Borah, Deva K.↗
DOE OSTI2020

Observation of attosecond electron dynamics in the photoelectron momentum distribution of atoms using few-cycle laser pulses

The method of time-resolved measurement with ultrashort laser pulses is vital to the development of attosecond science. Pump-probe measurements using a train of attosecond pulses in combination with a near-infrared (NIR) multicycle driving laser have been successful in capturing the intercycle electron dynamics which repeats every optical cycle and leads to above-threshold ionization (ATI) spectra in the frequency domain. Here in this work, we study the effect of a carrier-envelope phase (CEP) in a few-cycle (< 6 fs) NIR laser pulse on the photoelectron momentum distribution (PMD) of a hydrogen atom and show that interference patterns in a PMD change dramatically with CEPs in the few-cycle regime. When the few-cycle driving laser pulse has a sine shape, the double-slit interference with characteristic modulation of ATI peaks dominates the PMD. On the other hand, when the driving pulse has a cosine shape, the holographical interference featured by a spider-like pattern is isolated. Our results suggest that the CEP-stable few-cycle laser pulses can be used to identify different types of intracycle interference structures in a PMD which reveal the underlying subcycle electron dynamics on an attosecond timescale.

74 ATOMIC AND MOLECULAR PHYSICS↗
NASA NTRS1984

Configuration study for a 30 GHz monolithic receive array, volume 1

Gregorian, Cassegrain, and single reflector systems were analyzed in configuration studies for communications satellite receive antennas. Parametric design and performance curves were generated. A preliminary design of each reflector/feed system was derived including radiating elements, beam-former network, beamsteering system, and MMIC module architecture. Performance estimates and component requirements were developed for each design. A recommended design was selected for both the scanning beam and the fixed beam case. Detailed design and performance analysis results are presented for the selected Cassegrain configurations. The final design point is characterized in detail and performance measures evaluated in terms of gain, sidelobe level, noise figure, carrier-to-interference ratio, prime power, and beamsteering. The effects of mutual coupling and excitation errors (including phase and amplitude quantization errors) are evaluated. Mechanical assembly drawings are given for the final design point. Thermal design requirements are addressed in the mechanical design.

Nester, W. H.↗
DOE OSTI2025

Filter-Banks for Ultra-Wideband Communications, Sensing, and Localization

Recently, filterbank multi-carrier spread spectrum (FBMC-SS) has been proposed as a candidate waveform for ultrawideband (UWB) communications. It has been noted that FBMCSS is a perfect match to this application, leading to a trivial method of matching to the required spectral mask at different regions of the world. FBMC-SS also allows easy rejection of high-power interfering signals that may appear over different parts of the UWB spectral band. In this paper, we concentrate on the use of staggered multitone spread spectrum (SMT-SS) for UWB communications. SMT makes use of offset QAM modulation to transmit data symbols over narrowband, overlapping subcarrier bands. This form of FBMC-SS is well-suited to UWB communications because it has good spectral efficiency and a flat power spectral density (PSD), resulting in good utilization of the UWB spectral mask. Additionally, we explore new methods for multi-coding that result in higher bit rates than previous FBMCSS systems. Moreover, we study methods for equalizing the UWB multipath channel and cancelling narrowband interference. Excellent performance of the proposed methods are substantiated by presenting simulation results.

99 - GENERAL AND MISCELLANEOUS↗
DOE OSTI2026

From photosynthetic electron flow to gene regulation: redox signal transduction in cyanobacteria

In cyanobacteria, the free-living ancestors of chloroplasts, photosynthesis simultaneously sustains growth and generates reactive oxygen species (ROS) that damage proteins, lipids, and DNA when light capture outpaces carbon fixation. Maintaining redox balance, therefore, requires cells to read photosynthetic electron flow as a signal that continuously tunes gene expression and protein activity. This review traces how these redox signals are transduced to transcription machinery through three routes: membrane-localized sensors, cytoplasmic redox sensors downstream of photosystem I, and ROS generated when electron sinks are saturated. Membrane-bound histidine kinases (two-component systems) relay the redox state of the plastoquinone pool to control photosystem remodeling, pigment biosynthesis, and circadian timing. Cytoplasmic one-component regulators, by contrast, sense redox directly through thiol-disulfide switches, glutathionylation, iron-sulfur clusters, and metal-catalyzed oxidation to control photosystem-cofactor, electron-carrier, and transition-metal homeostasis. Because many of these regulators persist in algal and plant chloroplasts, cyanobacteria illuminate principles of redox control across photosynthetic eukaryotes. Post-transcriptional and translational control further shapes redox-dependent gene expression programs through transcript stability, ribosome assembly, and translation initiation, extending redox regulation beyond transcription to every step of protein synthesis and even activity modulation. Finally, we connect redox regulation to photosynthetic physiology, stress resilience, and the rational engineering of cyanobacteria for sustainable bioproduction.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS2000

Realization of Ultra-High Spectral Purity with the Opto-Electronic Oscillator

Recent results with the Opto-Electronic Oscillator (OEO) have led to the realization of very high spectral purity. Experimental results have produced a performance characterized by a noise as low as by -50 dBc/Hz at 10 Hz for a 10 GHz OEO. The unit was built in a compact package containing an integrated DFB laser and the modulator. This performance is significant because the oscillator is free running, and since the noise in an OEO is independent of the oscillation frequency, the same result can also be obtained at higher frequencies. The result also demonstrates that high frequency, high performance, low cost, and miniature OEO can be realized with the integrated photonic technology. We have also developed a novel carrier suppression technique to reduce the 1/f phase noise of the oscillator even further. The technique is based on the use of a long fiber delay, in place of the high Q cavity, to implement carrier suppression. Our preliminary experimental results indicate an extra 10 to 20 dB phase noise reduction of the OEO with this novel technique. Further noise reduction beyond this value is expected with improved circuit design and longer reference fiber.

Yao, Steve↗
DOE OSTI2017

Separation of Actinides from Lanthanides in Molten Fluorides by the Modulated-Current Electrolysis

Recently, the Molten Salt Reactor (MSR) is taking a renewed attraction as one of the reactor systems highlighted by the Generation IV International Forum. It is a non-classical (liquid fuel) system which can be operated as a breeder within the {sup 232}Th-{sup 233}U fuel cycle with the very interesting breeding factor. The necessary precondition for its proper functionality is the online reprocessing within the MSR's fuel cycle. A lot of effort is given to the development of the on-line pyrochemical reprocessing technology. Among the processes considered to be suitable for this process, the electrochemical separations are highlighted. Within this context, it is necessary to study electrochemical behavior of both fissile material and fission products in the molten salt systems and to develop the processes of their extraction from the system at various stages of the whole cycle. In this contribution, the study of the electrochemical separation of U from Gd in the LiF-CaF{sub 2} molten system by the modulated current electrolysis is presented. The study of MSR-related electrochemistry will continue as a part of the new Czech MSR R and D program. The knowledge of the electrochemical behavior of actinides and lanthanides in molten fluorides is necessary to the development of any electrochemical separation process. In our previous work, electrochemical characteristics of uranium, thorium, as well as that of several lanthanides, were measured in LiF-BeF{sub 2} (the basic melt considered for the MSR concept) and Be-free melts (LiF-NaFKF, LiF-NaF, LiF-CaF{sub 2}), and added to available literature data. If the fluoride carrier melt is electrochemically stable enough, it is possible to deposit the element of interest in its basic, metallic state (e.g. uranium in all types of fluoride melts tested) by the electrolysis. In the case of insufficient electrochemical stability of the fluoride melt in which the actinides and lanthanides are dissolved for the experiments, it is possible to use a reactive working electrode made of a material which creates alloys with the element to be deposited. An alloying reaction can shift the deposition potential in a favorable direction and therefore achieve the separation of an element from the system. The use of reactive electrode can also improve the adhesion of the deposit. When two or more electroactive species are present in the system at the same time, the efficiency of their separation by an electrolysis depends on how different the deposition potentials of these two species are. If we input certain modulation to the electrolytic current, we can improve overall result of an electrolytic experiment.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Potential dependent spectroelectrochemistry of electrofluorogenic dyes on indium–tin oxide

Indium-tin oxide (ITO) is used in a variety of applications due to its electrical conductivity and optical transparency. Moreover, ITO-coated glass is a common working electrode for spectroelectrochemistry. Thus, the ITO substrates should exhibit well-understood spectroscopic characteristics. Here, we report anomalous potential-dependent luminescence emission from three structurally dissimilar electrofluorogenic probe on ITO-coated glass. The three probes, flavin mononucleotide, resorufin, and Nile blue, show the expected fluorescence modulation between their oxidized, emissive forms and their reduced, nonfluorescent forms at low laser irradiance and/or high concentrations. However, at high irradiance and/or low concentration, the emission intensity increases at reducing potentials, contrary to expectations. In addition, a strong interplay between probe molecule concentration and laser irradiance is observed. We attribute the anomalous behavior to a combination of (1) irradiance-dependent ITO carrier dynamics, and (2) interaction of the fluorescent probe with ITO at reducing potentials resulting in a charge transfer state with altered emission behavior. Thus, the potential- and irradiance-dependent behavior of ITO and the resulting charge transfer state may not only interfere with the observation of potential-dependent fluorescence from redox probes but can completely reverse the polarity of the potential-dependent luminescence, especially at high irradiance and low concentration.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1992

Time-resolved far-field analysis of a high power single emitter laser diode

A system was developed which is capable of measuring the time-resolved far-field radiation patterns from a high-power semiconductor laser under intensity modulated conditions. Angular steering of the fundamental spatial mode was observed, with pointing variations as large as 0.5 deg, or 7.5 percent of the beamwidth, during the time of the optical pulse. The variations in pointing angle were directly related to gradients in the transverse index profile of the laser, which may oscillate based on lateral spatial hole burning of the gain and carrier density.

Cornwell, Donald M., Jr.↗
DOE OSTI2017

Final Scientific/Technical Report for Program Title: Solar Powered Dewvaporation Desalination System

Desalination technologies have been used increasingly throughout the world to produce the drinking water from the brackish ground and sea water for the past few decades. Among the commercially available desalination technologies, reverse osmosis (RO) and multi-stage flash distillation are the most widely used technologies globally. However, these technologies are difficult to be directly integrated with green energies without converting them to electricity. Dewvaporation, a desalination process, uses saturated steam as a carrier-gas to evaporate water from saline feeds and form pure condensate. It has the major technical benefit of reusing energy, released from vapor condensation, multiple times. The current proposal has been planned to address this issue. In Phase I, we have successfully demonstrated the feasibility of a new plasmonic nanoparticle based approach through fabrication and evaluation of a solar powered water vapor generation module. The water vapor generation module allows generation of high temperature plasmon on a fiber bundle end, where strong water and plasmon interaction occurs generating water vapor. Plasmon enhanced water evaporation has been realized on plasmonic nanoparticle immobilized substrate with an energy conversion efficiency of over 50%.

14 SOLAR ENERGY↗
NASA NTRS2004

High Electron Mobility SiGe/Si Transistor Structures on Sapphire Substrates

SiGe/Si n-type modulation doped field effect structures and transistors (n-MODFETs) have been fabricated on r-plane sapphire substrates. The structures were deposited using molecular beam epitaxy, and antimony dopants were incorporated via a delta doping process. Secondary ion mass spectroscopy (SIMS) indicates that the peak antimony concentration was approximately 4 x 10(exp 19) per cubic centimeter. At these two temperatures, the electron carrier densities were 1.6 and 1.33 x 10(exp 12) per square centimeter, thus demonstrating that carrier confinement was excellent. Shubnikov-de Haas oscillations were observed at 0.25 K, thus confirming the two-dimensional nature of the carriers. Transistors, with gate lengths varying from 1 micron to 5 microns, were fabricated using these structures and dc characterization was performed at room temperature. The saturated drain current region extended over a wide source-to-drain voltage (V (sub DS)) range, with V (sub DS) knee voltages of approximately 0.5 V and increased leakage starting at voltages slightly higher than 4 V.

Alterovitz, Samuel A.↗