Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BOUNDARY CONDITIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

RANS Simulation of Variable Density Turbulent Round Jets with Coflow using xRAGE Hydrodynamic Code and BHR Turbulence Models

This work for the fiscal year 2023 (FY23) is a continuation of previous efforts to evaluate the BHR turbulence models for their ability to accurately simulate variable density turbulent round jets with coflow. As before, RANS simulations are carried out using the xRAGE hydrodynamic code. The following are some of the previous findings. Israel showed that i) the symmetry boundary conditions for the BHR models in axisymmetric simulations were in error, ii) three grids of different resolutions did not lead to converging solutions, and iii) BHR 3.1 simulation exhibited instabilities and did not reach a steady state. Saenz and Rauenzahn derived and implemented into xRAGE the correct BHR boundary conditions at the symmetry axis. Cline conducted sensitivity studies with various parameters including the BHR models (versions 2, 3.1 and 4), gravity, material pressure, specific heat, initial turbulent kinetic energy and initial turbulent length scale, and found that the largest factor impacting on simulation results was the BHR model version, followed by the initial turbulent length scale. In addition, freeze boundary conditions at the exit and the side wall of the computational domain were used to remove anomalous flow behavior. Cline adjusted the inlet jet velocity, initial turbulent kinetic energy and initial turbulent length scale to obtain the best reasonable match with the experimental data of Charonko and Prestridge. It was found that the BHR 2 and 3.1 models performed in a similar manner, but the BHR 2 model produced much lower levels of density-specific-volume covariance and turbulent kinetic energy. The main focus for the FY23 is to study the effects of computational parameters related to the boundary conditions, mesh, domain size and timestep size. The reasoning behind this is that, unless simulation results can be shown to be reasonably independent from the aforementioned computational parameters, it would be difficult to attribute any discrepancies between simulation and experimental results to turbulence models. This important aspect has largely been overlooked in the previous years, and therefore will be studied comprehensively here. Additionally, effects of varying the initial turbulent length scale will be examined because it was previously identified as a major factor affecting the flow fields.

42 ENGINEERING↗

NUMERICAL SUNSPOT MODELS: ROBUSTNESS OF PHOTOSPHERIC VELOCITY AND MAGNETIC FIELD STRUCTURE

MHD simulations of sunspots have successfully reproduced many aspects of sunspot fine structure as a consequence of magneto-convection in inclined magnetic field. We study how global sunspot properties and penumbral fine structure depend on the magnetic top boundary condition as well as on grid spacing. The overall radial extent of the penumbra is subject to the magnetic top boundary condition. All other aspects of sunspot structure and penumbral fine structure are resolved at an acceptable level starting from a grid resolution of 48 [24] km (horizontal [vertical]). We find that the amount of inverse polarity flux and the overall amount of overturning convective motions in the penumbra are robust with regard to both resolution and boundary conditions. At photospheric levels Evershed flow channels are strongly magnetized. We discuss in detail the relation between velocity and magnetic field structure in the photosphere and point out observational consequences.

79 ASTRONOMY AND ASTROPHYSICS↗

Stability of Cylindrical and Conical Shells of Circular Cross Section, with Simultaneous Action of Axial Compression and External Normal Pressure

We consider in this report the determination of the upper limit of critical loads in the case of simultaneous action of a compressive force, uniformly distributed over plane cross sections, and of isotropic external normal pressure on cylindrical or conical shells of circular cross section. As a starting point we use the differential equations for neutral equilibrium of conical shells which have been used for the solution of the problem of stability of conical shells under torsion and under axial compression; upon solution of the problem it is possible to satisfy all boundary conditions, in contrast to the report where no attention is paid to the fulfillment of the boundary conditions, and to the report where only part of the boundary conditions are satisfied by solution of the problem according to Galerkin's method. Approximate formulas are used for the determination of the critical external normal pressure with simultaneous action of longituninal compression. Let us note that the formulas suggested in reference 5 are not well founded and may lead, in a number of cases, to a substantial mistake in the magnitude of the critical load.

Mushtari, K. M.↗

Analysis of the electromagnetic scattering from an inlet geometry with lossy walls

One of the primary goals is to develop an approximate but sufficiently accurate analysis for the problem of electromagnetic (EM) plane wave scattering by an open ended, perfectly-conducting, semi-infinite hollow circular waveguide (or duct) with a thin, uniform layer of lossy or absorbing material on its inner wall, and with a simple termination inside. The less difficult but useful problem of the EM scattering by a two-dimensional (2-D), semi-infinite parallel plate waveguide with an impedance boundary condition on the inner walls was chosen initially for analysis. The impedance boundary condition in this problem serves to model a thin layer of lossy dielectric/ferrite coating on the otherwise perfectly-conducting interior waveguide walls. An approximate but efficient and accurate ray solution was obtained recently. That solution is presently being extended to the case of a moderately thick dielectric/ferrite coating on the walls so as to be valid for situations where the impedance boundary condition may not remain sufficiently accurate.

Myung, N. H.↗

WE-AB-BRA-02: Development of Biomechanical Models to Describe Dose-Volume Response to Liver Stereotactic Body Radiation Therapy (SBRT) Patients

Purpose: Previous studies have shown that radiotherapy treatment for liver metastases causes marked liver hypertrophy in areas receiving low dose and atrophy/fibrosis in areas receiving high dose. The purpose of this work is to develop and evaluate a biomechanical model-based dose-response model to describe these liver responses to SBRT. Methods: In this retrospective study, a biomechanical model-based deformable registration algorithm, Morfeus, was expanded to include dose-based boundary conditions. Liver and tumor volumes were contoured on the planning images and CT/MR images three months post-RT and converted to finite element models. A thermal expansion-based relationship correlating the delivered dose and volume response was generated from 22 patients previously treated. This coefficient, combined with the planned dose, was applied as an additional boundary condition to describe the volumetric response of the liver of an additional cohort of metastatic liver patients treated with SBRT. The accuracy of the model was evaluated based on overall volumetric liver comparisons and the target registration error (TRE) using the average deviations in positions of identified vascular bifurcations on each set of registered images, with a target accuracy of the 2.5mm isotropic dose grid (vector dimension 4.3mm). Results: The thermal expansion coefficient models the volumetric change of the liver to within 3%. The accuracy of Morfeus with dose-expansion boundary conditions a TRE of 5.7±2.8mm compared to 11.2±3.7mm using rigid registration and 8.9±0.28mm using Morfeus with only spatial boundary conditions. Conclusion: A biomechanical model has been developed to describe the volumetric and spatial response of the liver to SBRT. This work will enable the improvement of correlating functional imaging with delivered dose, the mapping of the delivered dose from one treatment onto the planning images for a subsequent treatment, and will further provide information to assist with the biological characterization of patients’ response to radiation.

60 APPLIED LIFE SCIENCES↗

Program VSAERO theory document: A computer program for calculating nonlinear aerodynamic characteristics of arbitrary configurations

The VSAERO low order panel method formulation is described for the calculation of subsonic aerodynamic characteristics of general configurations. The method is based on piecewise constant doublet and source singularities. Two forms of the internal Dirichlet boundary condition are discussed and the source distribution is determined by the external Neumann boundary condition. A number of basic test cases are examined. Calculations are compared with higher order solutions for a number of cases. It is demonstrated that for comparable density of control points where the boundary conditions are satisfied, the low order method gives comparable accuracy to the higher order solutions. It is also shown that problems associated with some earlier low order panel methods, e.g., leakage in internal flows and junctions and also poor trailing edge solutions, do not appear for the present method. Further, the application of the Kutta conditions is extremely simple; no extra equation or trailing edge velocity point is required. The method has very low computing costs and this has made it practical for application to nonlinear problems requiring iterative solutions for wake shape and surface boundary layer effects.

Maskew, Brian↗

Determination of unknown thermal coefficients in a Stefan problem for Storm’s type materials

We consider a nonlinear one-dimensional Stefan problem for a semi-infinite material x>0, with phase change temperature T{sub f}. We assume that the heat capacity and the thermal conductivity satisfy a Storm’s condition. A convective boundary condition and a heat flux over-specified condition on the fixed face x=0 are considered. Unknown thermal coefficients are determined for the free boundary problem and for the associate moving boundary problem and we give sufficient conditions to obtain a parametric representation of a similarity type solution. Moreover, we give formulae for the thermal coefficients in both cases.

42 ENGINEERING↗

Helfrich-Hurault elastic instabilities driven by geometrical frustration

Here, the Helfrich-Hurault (HH) elastic instability is a well-known mechanism behind patterns that form as a result of strain upon liquid crystal systems with periodic ground states. In the HH model, layered structures undulate and buckle in response to local, geometric incompatibilities in order to maintain the preferred layer spacing. Classic HH systems include cholesteric liquid crystals under electromagnetic field distortions and smectic liquid crystals under mechanical strains, where both materials are confined between rigid substrates. However, richer phenomena are observed when undulation instabilities occur in the presence of deformable interfaces and variable boundary conditions. Understanding how the HH instability is affected by deformable surfaces is imperative for applying the instability to a broader range of materials. In this review, the HH mechanism is reexamined and special focus is given to how the boundary conditions influence the response of lamellar systems to geometrical frustration. Lamellar liquid crystals confined within a spherical shell geometry are used as the model system. Made possible by the relatively recent advances in microfluidics within the past 15 years, liquid crystal shells are composed entirely of fluid interfaces and have boundary conditions that can be dynamically controlled at will. Past and recent work that exemplifies how topological constraints, molecular anchoring conditions, and boundary curvature can trigger the HH mechanism in liquid crystals with periodic ground states is examined. The review ends by identifying similar phenomena across a wide variety of materials, both biological and synthetic. The fact that the HH mechanism is a generic and often overlooked response of periodic materials to geometrical frustration is highlighted.

42 ENGINEERING↗

Effects of nozzle-exit boundary-layer conditions on excitability of heated free jets

This paper reports an experimental study on the effects of nozzle-exit boundary-layer conditions on the excitability of heated free jets. The results were obtained at a Mach number 0.8 and total temperatures of 300 K and 670 K. External acoustic excitation was used to excite the jet. The excitation frequencies ranged up to 6 KHZ and the excitation levels were up to 150 dB. A level of 147 dB was used for most of the test points. Nozzle-exit boundary-layer characteristics were controlled by boundary layer tripping upstream of the nozzle exit plane. It has been shown that the free jet mixing rate strongly depends on the boundary-layer characteristics at the nozzle exit. Further, it appears that jets with a thin laminar nozzle-exit boundary layer are more selective about the optimum excitation frequency than those with a thick turbulent nozzle-exit boundary layer. Finally, for the jet of Mach number 0.8, it appears that free jet mixing and development may be controlled by flow excitation as well as by nozzle-exit boundary-layer modifications.

Lepicovsky, J.↗

Statistical Calibration and Validation of a Homogeneous Ventilated Wall-Interference Correction Method for the National Transonic Facility

Wind tunnel experiments will continue to be a primary source of validation data for many types of mathematical and computational models in the aerospace industry. The increased emphasis on accuracy of data acquired from these facilities requires understanding of the uncertainty of not only the measurement data but also any correction applied to the data. One of the largest and most critical corrections made to these data is due to wall interference. In an effort to understand the accuracy and suitability of these corrections, a statistical validation process for wall interference correction methods has been developed. This process is based on the use of independent cases which, after correction, are expected to produce the same result. Comparison of these independent cases with respect to the uncertainty in the correction process establishes a domain of applicability based on the capability of the method to provide reasonable corrections with respect to customer accuracy requirements. The statistical validation method was applied to the version of the Transonic Wall Interference Correction System (TWICS) recently implemented in the National Transonic Facility at NASA Langley Research Center. The TWICS code generates corrections for solid and slotted wall interference in the model pitch plane based on boundary pressure measurements. Before validation could be performed on this method, it was necessary to calibrate the ventilated wall boundary condition parameters. Discrimination comparisons are used to determine the most representative of three linear boundary condition models which have historically been used to represent longitudinally slotted test section walls. Of the three linear boundary condition models implemented for ventilated walls, the general slotted wall model was the most representative of the data. The TWICS code using the calibrated general slotted wall model was found to be valid to within the process uncertainty for test section Mach numbers less than or equal to 0.60. The scatter among the mean corrected results of the bodies of revolution validation cases was within one count of drag on a typical transport aircraft configuration for Mach numbers at or below 0.80 and two counts of drag for Mach numbers at or below 0.90.

Walker, Eric Lee↗

Statistical Calibration and Validation of a Homogeneous Ventilated Wall-Interference Correction Method for the National Transonic Facility

Wind tunnel experiments will continue to be a primary source of validation data for many types of mathematical and computational models in the aerospace industry. The increased emphasis on accuracy of data acquired from these facilities requires understanding of the uncertainty of not only the measurement data but also any correction applied to the data. One of the largest and most critical corrections made to these data is due to wall interference. In an effort to understand the accuracy and suitability of these corrections, a statistical validation process for wall interference correction methods has been developed. This process is based on the use of independent cases which, after correction, are expected to produce the same result. Comparison of these independent cases with respect to the uncertainty in the correction process establishes a domain of applicability based on the capability of the method to provide reasonable corrections with respect to customer accuracy requirements. The statistical validation method was applied to the version of the Transonic Wall Interference Correction System (TWICS) recently implemented in the National Transonic Facility at NASA Langley Research Center. The TWICS code generates corrections for solid and slotted wall interference in the model pitch plane based on boundary pressure measurements. Before validation could be performed on this method, it was necessary to calibrate the ventilated wall boundary condition parameters. Discrimination comparisons are used to determine the most representative of three linear boundary condition models which have historically been used to represent longitudinally slotted test section walls. Of the three linear boundary condition models implemented for ventilated walls, the general slotted wall model was the most representative of the data. The TWICS code using the calibrated general slotted wall model was found to be valid to within the process uncertainty for test section Mach numbers less than or equal to 0.60. The scatter among the mean corrected results of the bodies of revolution validation cases was within one count of drag on a typical transport aircraft configuration for Mach numbers at or below 0.80 and two counts of drag for Mach numbers at or below 0.90.

Walker, Eric L.↗

NSFnets (Navier-Stokes flow nets): Physics-informed neural networks for the incompressible Navier-Stokes equations

In the last 50 years there has been a tremendous progress in solving numerically the Navier-Stokes equations using finite differences, finite elements, spectral, and even meshless methods. Yet, in many real cases, we still cannot incorporate seamlessly (multi-fidelity) data into existing algorithms, and for industrial-complexity applications the mesh generation is time consuming and still an art. Moreover, solving ill-posed problems (e.g., lacking boundary conditions) or inverse problems is often prohibitively expensive and requires different formulations and new computer codes. Here, we employ physics-informed neural networks (PINNs), encoding the governing equations directly into the deep neural network via automatic differentiation, to overcome some of the aforementioned limitations for simulating incompressible laminar and turbulent flows. We develop the Navier-Stokes flow nets (NSFnets) by considering two different mathematical formulations of the Navier-Stokes equations: the velocity-pressure (VP) formulation and the vorticity-velocity (VV) formulation. Since this is a new approach, we first select some standard benchmark problems to assess the accuracy, convergence rate, computational cost and flexibility of NSFnets; analytical solutions and direct numerical simulation (DNS) databases provide proper initial and boundary conditions for the NSFnet simulations. The spatial and temporal coordinates are the inputs of the NSFnets, while the instantaneous velocity and pressure fields are the outputs for the VP-NSFnet, and the instantaneous velocity and vorticity fields are the outputs for the VV-NSFnet. This is unsupervised learning and, hence, no labeled data are required beyond boundary and initial conditions and the fluid properties. The residuals of the VP or VV governing equations, together with the initial and boundary conditions, are embedded into the loss function of the NSFnets. No data is provided for the pressure to the VP-NSFnet, which is a hidden state and is obtained via the incompressibility constraint without extra computational cost. Unlike the traditional numerical methods, NSFnets inherit the properties of neural networks (NNs), hence the total error is composed of the approximation, the optimization, and the generalization errors. Here, we empirically attempt to quantify these errors by varying the sampling (“residual”) points, the iterative solvers, and the size of the NN architecture. For the laminar flow solutions, we show that both the VP and the VV formulations are comparable in accuracy but their best performance corresponds to different NN architectures. The initial convergence rate is fast but the error eventually saturates to a plateau due to the dominance of the optimization error. For the turbulent channel flow, we show that NSFnets can sustain turbulence at , but due to expensive training we only consider part of the channel domain and enforce velocity boundary conditions on the subdomain boundaries provided by the DNS data base. We also perform a systematic study on the weights used in the loss function for balancing the data and physics components, and investigate a new way of computing the weights dynamically to accelerate training and enhance accuracy. In the last part, we demonstrate how NSFnets should be used in practice, namely for ill-posed problems with incomplete or noisy boundary conditions as well as for inverse problems. We obtain reasonably accurate solutions for such cases as well without the need to change the NSFnets and at the same computational cost as in the forward well-posed problems. As a result, we also present a simple example of transfer learning that will aid in accelerating the training of NSFnets for different parameter settings.

97 MATHEMATICS AND COMPUTING↗

Stability of jammed packings II: the transverse length scale

As a function of packing fraction at zero temperature and applied stress, an amorphous packing of spheres exhibits a jamming transition where the system is sensitive to boundary conditions even in the thermodynamic limit. Upon further compression, the system should become insensitive to boundary conditions provided it is sufficiently large. Here we explore the linear response to a large class of boundary perturbations in 2 and 3 dimensions. We consider each finite packing with periodic-boundary conditions as the basis of an infinite square or cubic lattice and study properties of vibrational modes at arbitrary wave vector. We find that the stability of such modes can be understood in terms of a competition between plane waves and the anomalous vibrational modes associated with the jamming transition; infinitesimal boundary perturbations become irrelevant for systems that are larger than a length scale that characterizes the transverse excitations. This previously identified length diverges at the jamming transition.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Green's function methods for multiphysics simulations (Final Report)

Green's functions are important tools for analyzing mathematical properties of partial differential equations (PDEs), and for numerically solving PDEs, especially when equations for the same operator but with multiple right hand sides need to be solved simultaneously. This proposal aims at developing efficient and accurate numerical methods for computing Green's functions, which can be used to tackle a challenging question in multiphysics simulation of DOE-mission science problems: how to couple quantum physics with classical physics. The key mathematical difficulty is properly formulate a "boundary condition" for the region described by quantum physics, and conventional approaches often model such boundary conditions in an empirical way. The proposed Green's function methods use the Dirichlet-to-Neumann map to formulate a boundary condition that is non-empirical and can couple the quantum and classical regions in an in principle exact way. The key ingredient of the new methods is to construct the Dirichlet-to-Neumann map in an efficient, accurate and versatile manner. The new methods have provably low complexity and are ideally suited for massively parallel and emerging many-core computational systems.

97 MATHEMATICS AND COMPUTING↗

Tests of smoothing methods for topological study of galaxy redshift surveys

Studying the topology of large-scale structure as a way to better understand initial conditions has become more widespread in recent years. Studying topology of simulations (which have periodic boundary conditions) in redshift space produces results compatible with the real topological characteristics of the simulation. Thus we expect we can extract useful information from redshift surveys. However, with nonperiodic boundary conditions, the use of smoothing must result in the loss of information at survey boundaries. In this paper, we test different methods of smoothing samples with nonperiodic boundary conditions to see which most efficiently preserves the topological features of the real distribution. We find that a smoothing method which (unlike most previous published analysis) sums only over cells inside the survey volume produces the best results among the schemes tested.

Melott, Adrian L.↗

Self-consistent field theory simulations of polymers on arbitrary domains

We introduce a framework for simulating the mesoscale self-assembly of block copolymers in arbitrary confined geometries subject to Neumann boundary conditions. We employ a hybrid finite difference/volume approach to discretize the mean-field equations on an irregular domain represented implicitly by a level-set function. The numerical treatment of the Neumann boundary conditions is sharp, i.e. it avoids an artificial smearing in the irregular domain boundary. This strategy enables the study of self-assembly in confined domains and enables the computation of physically meaningful quantities at the domain interface. In addition, we employ adaptive grids encoded with Quad-/Oc-trees in parallel to automatically refine the grid where the statistical fields vary rapidly as well as at the boundary of the confined domain. This approach results in a significant reduction in the number of degrees of freedom and makes the simulations in arbitrary domains using effective boundary conditions computationally efficient in terms of both speed and memory requirement. Finally, in the case of regular periodic domains, where pseudo-spectral approaches are superior to finite differences in terms of CPU time and accuracy, we use the adaptive strategy to store chain propagators, reducing the memory footprint without loss of accuracy in computed physical observables.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Studies Related to the Oregon State University High Temperature Test Facility: Scaling, the Validation Matrix, and Similarities to the Modular High Temperature Gas-Cooled Reactor

The Oregon State University (OSU) High Temperature Test Facility (HTTF) is an integral experimental facility that will be constructed on the OSU campus in Corvallis, Oregon. The HTTF project was initiated, by the U.S. Nuclear Regulatory Commission (NRC), on September 5, 2008 as Task 4 of the 5 year High Temperature Gas Reactor Cooperative Agreement via NRC Contract 04-08-138. Until August, 2010, when a DOE contract was initiated to fund additional capabilities for the HTTF project, all of the funding support for the HTTF was provided by the NRC via their cooperative agreement. The U.S. Department of Energy (DOE) began their involvement with the HTTF project in late 2009 via the Next Generation Nuclear Plant project. Because the NRC interests in HTTF experiments were only centered on the depressurized conduction cooldown (DCC) scenario, NGNP involvement focused on expanding the experimental envelope of the HTTF to include steady-state operations and also the pressurized conduction cooldown (PCC). Since DOE has incorporated the HTTF as an ingredient in the NGNP thermal-fluids validation program, several important outcomes should be noted: 1. The reference prismatic reactor design, that serves as the basis for scaling the HTTF, became the modular high temperature gas-cooled reactor (MHTGR). The MHTGR has also been chosen as the reference design for all of the other NGNP thermal-fluid experiments. 2. The NGNP validation matrix is being planned using the same scaling strategy that has been implemented to design the HTTF, i.e., the hierarchical two-tiered scaling methodology developed by Zuber in 1991. Using this approach a preliminary validation matrix has been designed that integrates the HTTF experiments with the other experiments planned for the NGNP thermal-fluids verification and validation project. 3. Initial analyses showed that the inherent power capability of the OSU infrastructure, which only allowed a total operational facility power capability of 0.6 MW, is inadequate to permit steady-state operation at reasonable conditions. 4. To enable the HTTF to operate at a more representative steady-state conditions, DOE recently allocated funding via a DOE subcontract to HTTF to permit an OSU infrastructure upgrade such that 2.2 MW will become available for HTTF experiments. 5. Analyses have been performed to study the relationship between HTTF and MHTGR via the hierarchical two-tiered scaling methodology which has been used successfully in the past, e.g., APEX facility scaling to the Westinghouse AP600 plant. These analyses have focused on the relationship between key variables that will be measured in the HTTF to the counterpart variables in the MHTGR with a focus on natural circulation, using nitrogen as a working fluid, and core heat transfer. 6. Both RELAP5-3D and computational fluid dynamics (CD-Adapco’s STAR-CCM+) numerical models of the MHTGR and the HTTF have been constructed and analyses are underway to study the relationship between the reference reactor and the HTTF. The HTTF is presently being designed. It has ¼-scaling relationship to the MHTGR in both the height and the diameter. Decisions have been made to design the reactor cavity cooling system (RCCS) simulation as a boundary condition for the HTTF to ensure that (a) the boundary condition is well defined and (b) the boundary condition can be modified easily to achieve the desired heat transfer sink for HTTF experimental operations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Theoretical study of intrinsic defects in cubic silicon carbide 3C-SiC

Using the local moment counter charge (LMCC) method to accurately represent the asymptotic electrostatic boundary conditions within density functional theory supercell calculations, we present a comprehensive analysis of the atomic structure and energy levels of point defects in cubic silicon carbide (3C-SiC). Finding that the classical long-range dielectric screening outside the supercell induced by a charged defect is a significant contributor to the total energy. we describe and validate a modified Jost screening model to evaluate this polarization energy. This leads to bulk-converged defect levels in finite size supercells. With the LMCC boundary conditions and a standard Perdew-Burke-Ernzerhof (PBE) exchange correlation functional, the computed defect level spectrum exhibits no band gap problem: the range of defect levels spans ~2.4 eV, an effective defect band gap that agrees with the experimental band gap. Comparing with previous literature, our LMCC-PBE defect results are in consistent agreement with the hybrid-exchange functional results of Oda et al. [J. Chem. Phys. 139, 124707 (2013)] rather than their PBE results. The difference with their PBE results is attributed to their use of a conventional jellium approximation rather than the more rigorous LMCC approach for handling charged supercell boundary conditions. The difference between standard dft and hybrid functional results for defect levels lies not in a band gap problem but rather in solving a boundary condition problem. The LMCC-PBE entirely mitigates the effect of the band gap problem on defect levels. The more computationally economical PBE enables a systematic exploration of 3C-SiC defects, where, most notably, we find that the silicon vacancy undergoes Jahn-Teller-induced distortions from the previously assumed T d symmetry, and that the divacancy, like the silicon vacancy, exhibits a site-shift bistability in p -type conditions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗