Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Angle of attack”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

A Full-Envelope Air Data Calibration and Three-Dimensional Wind Estimation Method Using Global Output-Error Optimization and Flight-Test Techniques

A novel, efficient air data calibration method is proposed for aircraft with limited envelopes. This method uses output-error optimization on three-dimensional inertial velocities to estimate calibration and wind parameters. Calibration parameters are based on assumed calibration models for static pressure, angle of attack, and flank angle. Estimated wind parameters are the north, east, and down components. The only assumptions needed for this method are that the inertial velocities and Euler angles are accurate, the calibration models are correct, and that the steady-state component of wind is constant throughout the maneuver. A two-minute maneuver was designed to excite the aircraft over the range of air data calibration parameters and de-correlate the angle-of-attack bias from the vertical component of wind. Simulation of the X-48B (The Boeing Company, Chicago, Illinois) aircraft was used to validate the method, ultimately using data derived from wind-tunnel testing to simulate the un-calibrated air data measurements. Results from the simulation were accurate and robust to turbulence levels comparable to those observed in flight. Future experiments are planned to evaluate the proposed air data calibration in a flight environment.

Taylor, Brian R.↗
NASA NTRS1943

Limitations of Lifting-Line Theory for Estimation of Aileron Hinge-Moment Characteristics

Hinge-moment parameters for several typical ailerons were calculated from section data with the aspect-ratio correction as usually determined from lifting-line theory. The calculations showed that the agreement between experimental and calculated results was unsatisfactory. An additional aspect-ratio correction, calculated by the method of lifting-surface theory, was applied to the slope of the curve of hinge-moment coefficient against angle of attack at small angles of attack. This so-called streamline-curvature correction brought the calculated and experimental results into satisfactory agreement.

ATI-13584↗
NASA NTRS2019

Investigation of Reduced-Order Modeling for Aircraft Stability and Control Prediction

High-fidelity computational fluid dynamics tools offer the potential to approximate increments for ground-to-flight scaling effects, as well as to augment the dynamic damping derivative data for motion-based flight simulators. Unfortunately, the computational expense is currently prohibitive for populating a complete simulator database. This work investigates an existing surrogate-based, indicial response reduced-order model methodology as a means to efficiently augment a flight simulator database with high-fidelity nonlinear aerodynamic damping derivatives. Creation of the reduced-order model is based on the superposition integrals of the step response with the derivative of its corresponding input signal. Step responses are calculated using a computational grid motion approach that separates the effects of angle of attack and sideslip angle from angular rates, and rates from angle of attack and sideslip. It is demonstrated that the transients produced during the start of a forced-oscillation motion are captured by the reduced-order model to the level of fidelity of a comparable computational solution. Aerodynamic coefficients computed within minutes by the reduced-order model for an aircraft undergoing an 18-second half Lazy-8 maneuver and a 25-second Immelmann turn maneuver are compared with those from full computational flight solutions that required days to complete. Finally, a cost-benefit assessment is included that demonstrates a compelling advantage for this approach. d for maneuvering, flexible vehicles.

Frink, Neal T.↗
NASA NTRS1980

Experimental investigation of a 0.15 scale model of a conformal variable-ramp inlet for the F-16 airplane

A 0.15 scale model of a proposed conformal variable-ramp inlet for the Multirole Fighter was tested from Mach 0.8 to 2.2 at a wide range of angles of attack and sideslip. Inlet ramp angle was varied to optimize ramp angle as a function of engine airflow, Mach number, angle of attack, and angle of sideslip. Several inlet configuration options were investigated to study their effects on inlet operation and to establish the final flight configuration. These variations were cowl sidewall cutback, cowl lip bluntness, boundary layer bleed, and first-ramp leading edge shape. Diagnostic and engine face instrumentation were used to evaluate inlet operation at various inlet stations and at the inlet/engine interface. Pressure recovery and stability of the inlet were satisfactory for the proposed application. On the basis of an engine stability audit of the worst-case instantaneous distortion patterns, no inlet/engine compatibility problems are expected for normal operations.

Hawkins, J. E.↗
NASA NTRS1980

An experimental and analytical investigation of a hypersonic cruise vehicle at Mach 6

Flow field properties over a hypersonic vehicle are measured and compared with results from the numerical analysis of inviscid supersonic flow theory. Good agreement between theory and experiment at zero angle of attack, and significant discrepancy at angles of attack greater than or equal to 5 deg are found. The experiments indicate that turbulent boundary layer without flow separation exists over the model surface at zero angle of attack. Vortex lift-off, flow separation, and shock boundary layer interaction occur over the leeward surface, and near the wing-fuselage junction with angles of attack greater than or equal to 5 deg. Improvements of the existing numerical method to compute hypersonic cruise vehicle flow field at large angle of attack are presented.

Wang, C. R.↗
NASA NTRS1990

Wind-tunnel investigation of a flush airdata system at Mach numbers from 0.7 to 1.4

Flush pressure orifices installed on the nose section of a 1/7-scale model of the F-14 airplane were evaluated for use as a flush airdata system (FADS). Wing-tunnel tests were conducted in the 11- by 11-ft Unitary Wind Tunnel at NASA Ames Research Center. A full-scale FADS of the same configuration was previously tested using an F-14 aircraft at the Dryden Flight Research Facility of NASA Ames Research Center (Ames-Dryden). These tests, which were published, are part of a NASA program to assess accuracies of FADS for use on aircraft. The test program also provides data to validate algorithms for the shuttle entry airdata system developed at the NASA Langley Research Center. The wind-tunnel test Mach numbers were 0.73, 0.90, 1.05, 1.20, and 1.39. Angles of attack were varied in 2 deg increments from -4 deg to 20 deg. Sideslip angles were varied in 4 deg increments from -8 deg to 8 deg. Airdata parameters were evaluated for determination of free-stream values of stagnation pressure, static pressure, angle of attack, angle of sideslip, and Mach number. These parameters are, in most cases, the same as the parameters investigated in the flight test program. The basic FADS wind-tunnel data are presented in tabular form. A discussion of the more accurate parameters is included.

Larson, Terry J.↗
NASA NTRS1951

Aerodynamic Characteristics of a Flying-Boat Hull Having a Length-Beam Ratio of 15, TED No. NACA 2206

An investigation was made in the Langley 300 MPH 7- by 10-foot tunnel to determine the aerodynamic characteristics of a flying-boat hull of a length-beam ratio of 15 in the presence of a wing. The investigation was an extension of previous tests made on hulls of length-beam ratios of 6, 9, and 12; these hulls were designed to have approximately the same hydrodynamic performance with respect to spray and resistance characteristics. Comparison with the previous investigation at lower length-beam ratios indicated a reduction in minimum drag coefficients of 0.0006 (10 peroent)with fixed transition when the length-beam ratio was extended from 12 to 15. As with the hulls of lower length-beam ratio, the drag reduction with a length-beam ratio of 15 occurred throughout the range of angle of attack tested and the angle of attack for minimum drag was in the range from 2deg to 3deg. Increasing the length-beam ratio from 12 to 15 reduced the hull longitudinal instability by an mount corresponding to an aerodynamic-center shift of about 1/2 percent of the mean aerodynamic chord of the hypothetical flying boat. At an angle of attack of 2deg, the value of the variation of yawing-moment coefficient with angle of yaw for a length-beam ratio of 15 was 0.00144, which was 0.00007 larger than the value for a length-beam ratio of 12.

Riebe, John M.↗
NASA NTRS1993

Advanced launch system trajectory optimization using suboptimal control

The maximum-final mass trajectory of a proposed configuration of the Advanced Launch System is presented. A model for the two-stage rocket is given; the optimal control problem is formulated as a parameter optimization problem; and the optimal trajectory is computed using a nonlinear programming code called VF02AD. Numerical results are presented for the controls (angle of attack and velocity roll angle) and the states. After the initial rotation, the angle of attack goes to a positive value to keep the trajectory as high as possible, returns to near zero to pass through the transonic regime and satisfy the dynamic pressure constraint, returns to a positive value to keep the trajectory high and to take advantage of minimum drag at positive angle of attack due to aerodynamic shading of the booster, and then rolls off to negative values to satisfy the constraints. Because the engines cannot be throttled, the maximum dynamic pressure occurs at a single point; there is no maximum dynamic pressure subarc. To test approximations for obtaining analytical solutions for guidance, two additional optimal trajectories are computed: one using untrimmed aerodynamics and one using no atmospheric effects except for the dynamic pressure constraint. It is concluded that untrimmed aerodynamics has a negligible effect on the optimal trajectory and that approximate optimal controls should be able to be obtained by treating atmospheric effects as perturbations.

Shaver, Douglas A.↗
NASA NTRS1953

Investigation of the Effects of Propeller Operation on the Low-Speed Stability and Control Characteristics of a 1/6-Scale Model of a Revised Configuration of the Republic XF-84H Airplane

An investigation was made to determine the static longitudinal and lateral stability and control characteristics of a l/6-scale model of the revised Republic XF-84H airplane with and without the propeller operating. The model had a 40deg swept wing of aspect ratio 3.45 and was equipped with a thin, three-blade supersonic-type propeller. Modifications incorporated in the revised model included a raised horizontal tail, increased rudder size, wing fences at 65 percent semispan, and a modified wing leading edge outboard of the fences. The test results for flap-retracted and flap-deflected conditions indicated that the revised configuration should be satisfactory for most normal flight conditions provided the angle of attack does not exceed the angle for pitch-up. An abrupt pitch-up tendency of the model was evident for the zero thrust condition above approximately 15' angle of attack. Although the effects of power were destabilizing, power-on longitudinal stability was satisfactory through the angle-of-attack range for which the model was stable with zero thrust. Above the angle of attack for pitch-up, an uncontrollable left roll-off tendency would be expected with power on and slats retracted. Projection of wing slats or use of leading-edge chord-extensions with only the left extension drooped were found beneficial in controlling the roll-off tendency with power on; however the most effective means found was projection of only the left slat.

Sleeman, William C., Jr.↗
NASA NTRS2014

An Experimental Investigation of the 30P30N Multi-Element High-Lift Airfoil

High-lift devices often generate an unsteady flow field producing both broadband and tonal noise which radiates from the aircraft. In particular, the leading edge slat is often a dominant contributor to the noise signature. An experimental study of a simplified unswept high-lift configuration, the 30P30N, has been conducted to understand and identify the various flow-induced noise sources around the slat. Closed-wall wind tunnel tests are performed in the Florida State Aeroacoustic Tunnel (FSAT) to characterize the slat cove flow field using a combination of surface and off-body measurements. Mean surface pressures compare well with numerical predictions for the free-air configuration. Consistent with previous measurements and computations for 2D high-lift configurations, the frequency spectra of unsteady surface pressures on the slat surface display several narrowband peaks that decrease in strength as the angle of attack is increased. At positive angles of attack, there are four prominent peaks. The three higher frequency peaks correspond, approximately, to a harmonic sequence related to a feedback resonance involving unstable disturbances in the slat cove shear layer. The Strouhal numbers associated with these three peaks are nearly insensitive to the range of flow speeds (41-58 m/s) and the angles of attack tested (3-8.5 degrees). The first narrow-band peak has an order of magnitude lower frequency than the remaining peaks and displays noticeable sensitivity to the angle of attack. Stereoscopic particle image velocimetry (SPIV) measurements provide supplementary information about the shear layer characteristics and turbulence statistics that may be used for validating numerical simulations.

Pascioni, Kyle A.↗
NASA NTRS1985

Hypersonic characteristics of an advanced aerospace plane

A series of hypersonic wind-tunnel tests have been conducted in the NASA Langley Hypersonic Facilities Complex to obtain the static longitudinal and lateral-directional aerodynamic characteristics of an advanced aerospace plane. Data were obtained at 0 to 20 deg angles of attack and -3 to 3 deg angles of sideslip at Mach numbers of 6 and 10 in air and 20 in helium. Results show that stable trim capability exists at angles of attack near maximum lift-drag ratio (L/D). Both performance and stability exhibited some Mach number dependency. The vehicle was longitudinally unstable at low angles of attack but stable at angles of attack near and above maximum L/D. It was directionally unstable with positive dihedral effect. The rudder showed an inability to provide lateral-directional control, and removing the vertical tail resulted in increased directional instability. Analytical predictions of the static longitudinal aerodynamic coefficients gave relatively good comparisons with the experimental data.

Mccandless, R. S.↗
NASA NTRS2000

Geometric Perturbations and Asymmetric vortex shedding About Slender Pointed Bodies

The flow about slender, pointed bodies can be characterized by different states with angle of attack. At moderate-to-high angles of attack (alpha approximately equals 40deg), a steady, asymmetric vortex pattern develops along the body, leading to a net lateral force. At higher angles of attack (alpha approximately equals 60deg), the aft-end of the body develops an unsteady von Karman shedding. As the angle of attack approaches 90deg, the entire body length exhibits a time-dependent vortex shedding pattern. The current work uses three-dimensional, thin-layer Navier-Stokes simulations to investigate the physical mechanisms of asymmetric vortex shedding at alpha = 40deg and alpha = 60deg. The development of an asymmetric vortex pattern via a convective instability mechanism is investigated using tip bumps, surface roughness, and tip curvature. It's found that surface roughness simulations can incite an asymmetric vortex state at alpha = 60deg which is consistent with the application of a tip bumps, and the experimentally observed flowfield. The unsteady von Karman vortex shedding on the aft portion of the body is also well resolved. The use of surface roughness did not incite a flow asymmetry at alpha = 40deg, and it was necessary to simulate tip curvature at this angle of attack in order to generate an asymmetric vortex state.

Murman, Scott M.↗
NASA NTRS2000

Geometric Perturbations and Asymmetric Vortex Shedding about Slender Pointed Bodies

The flow about slender, pointed bodies can be characterized by different states with angle of attack. At moderate-to-high angles of attack (alpha approx. = 40 deg.), a steady, asymmetric vortex pattern develops along the body, leading to a net lateral force. At higher angles of attack (alpha approx. = 60 deg.), the aft-end of the body develops an unsteady von Karman shedding. As the angle of attack approaches 90 deg., the entire body length exhibits a time-dependent vortex shedding pattern. The current work uses three-dimensional, thin-layer Navier-Stokes simulations to investigate the physical mechanisms of asymmetric vortex shedding at alpha = 40 deg. and alpha = 60 deg. The development of an asymmetric vortex pattern via a convective instability mechanism is investigated using tip bumps, surface roughness, and tip curvature. It's found that surface roughness simulations can incite an asymmetric vortex state at alpha = 60 deg. which is consistent with the application of a tip bump, and the experimentally observed flowfield. The unsteady von Karman vortex shedding on the aft. portion of the body is also well resolved. The use of surface roughness did not incite a flow asymmetry at alpha = 40 deg., and it was necessary to simulate tip curvature at this angle of attack in order to generate an asymmetric vortex state.

Murman, Scott M.↗
NASA NTRS1960

Flight Investigation of an Automatic Pitchup Control

A flight investigation of an automatic pitchup control has been conducted by the National Aeronautics and Space Administration at the Langley Research Center. The pitching-moment characteristics of a transonic fighter airplane which was subject to pitchup were altered by driving the stabilizer in accordance with a signal that was a function of a combination of the measured angle of attack and the pitching velocity. An angle-of-attack threshold control was used to preset the angle of attack at which the automatic pitchup-control system would begin to drive the stabilizer. No threshold control as such existed for the pitching-velocity signal. A summing linkage in series with the pilot's longitudinal control allowed the automatic pitchup-control system to drive the stabilizer 13.5 percent of the total stabilizer travel independently of the pilot's control. Tests were made at an altitude of 35,000 feet over a Mach number range of 0.80 to 0.90. Various gearings between the control and the sensing devices were investigated. The automatic system was capable of extending the region of positive stability for the test airplane to angles of attack above the basic-airplane pitchup threshold angle of attack. In most cases a limit-cycle oscillation about the airplane pitch axis occurred.

Hurt, George J., Jr.↗
NASA NTRS1960

Investigation of the Subsonic Stability and Control Characteristics of a 1/7-Scale Model of the North American X-15 Airplane with and without Fuselage Forebody Strakes

An investigation of the low-subsonic stability and control characteristics of a l/7-scale free-flying model modified to represent closely the North American X-15 airplane (configuration 3) has been made in the Langley full-scale tunnel. Flight conditions at a relatively low altitude were simulated with the center of gravity at 16.0 percent of the mean aerodynamic chord. The longitudinal stability and control were considered to be satisfactory for all flight conditions tested. The lateral flight behavior was generally satisfactory for angles of attack below about 20 deg. At higher angles, however, the model developed a tendency to fly in a side-slipped attitude because of static directional instability at small sideslip angles. Good roll control was maintained to the highest angles tested, but rudder effectiveness diminished with increasing angle of attack and became adverse for angles above 40 deg. Removal of the lower rudder had little effect on the lateral flight characteristics for angles of attack less than about 20 deg but caused the lateral flight behavior to become worse in the high angle-of-attack range. The addition of small fuselage forebody strakes improved the static directional stability and lateral flight behavior of both configurations.

Hassell, James L., Jr.↗
NASA NTRS1976

Aerodynamic characteristics of a vane flow angularity sensor system capable of measuring flight path accelerations for the Mach number range from 0.40 to 2.54

The aerodynamic characteristics of the angle of attack vane and the angle of sideslip vane are summarized. The test conditions ranged in free stream Mach number from 0.40 to 2.54, in angle of attack from -2 deg to 22 deg, in angle of sideslip from -2 deg to 12 deg, and in Reynolds number from 590,000 per meter to 1.8 million per meter. The results of the wind tunnel investigation are compared with results obtained with similar vane configurations. Comparisons with a NACA vane configuration are also made. In addition, wind tunnel-derived upwash for the test installation is compared with analytical predictions.

Sakamoto, G. M.↗
NASA NTRS2015

Use of a Viscous Flow Simulation Code for Static Aeroelastic Analysis of a Wing at High-Lift Conditions

In this paper, we present a static aeroelastic analysis of a wind tunnel test model of a wing in high-lift configuration using a viscous flow simulation code. The model wing was tailored to deform during the tests by amounts similar to a composite airliner wing in highlift conditions. This required use of a viscous flow analysis to predict the lift coefficient of the deformed wing accurately. We thus utilized an existing static aeroelastic analysis framework that involves an inviscid flow code (Cart3d) to predict the deformed shape of the wing, then utilized a viscous flow code (Overflow) to compute the aerodynamic loads on the deformed wing. This way, we reduced the cost of flow simulations needed for this analysis while still being able to predict the aerodynamic forces with reasonable accuracy. Our results suggest that the lift of the deformed wing may be higher or lower than that of the non-deformed wing, and the washout deformation of the wing is the key factor that changes the lift of the deformed wing in two distinct ways: while it decreases the lift at low to moderate angles of attack simply by lowering local angles of attack along the span, it increases the lift at high angles of attack by alleviating separation.

Aeroelastic↗
NASA NTRS1959

Trajectory Control for Vehicles Entering the Earth's Atmosphere at Small Flight Path Angles

Methods of controlling the trajectories of high-drag-low-lift vehicles entering the earth's atmosphere at angles of attack near 90 deg and at initial entry angles up to 3 deg are studied. The trajectories are calculated for vehicles whose angle of attack can be held constant at some specified value or can be perfectly controlled as a function of some measured quantity along the trajectory. The results might be applied in the design of automatic control systems or in the design of instruments which will give the human pilot sufficient information to control his trajectory properly during an atmospheric entry. Trajectory data are compared on the basis of the deceleration, range, angle of attack, and, in some cases, the rate of descent. The aerodynamic heat-transfer rate and skin temperature of a vehicle with a simple heat-sink type of structure are calculated for trajectories made with several types of control functions. For the range of entry angles considered, it is found that the angle of attack can be controlled to restrict the deceleration down to an arbitrarily chosen level of 3g. All the control functions tried are successful in reducing the maximum deceleration to the desired level. However, in order to avoid a tendency for the deceleration to reach an initial peak decrease, and then reach a second peak, some anticipation is required in the control function so that the change in angle of attack will lead the change in deceleration. When the angle of attack is controlled in the aforementioned manner, the maximum rate of aerodynamic heat transfer to the skin is reduced, the maximum skin temperature of the vehicle is virtually unaffected, and the total heat absorbed is slightly increased. The increase in total heat can be minimized, however, by maintaining the maximum desired deceleration for as much of the trajectory as possible. From an initial angle of attack of 90 deg, the angle-of-attack requirements necessary to maintain constant values of deceleration (1g to 4g) and constant values of rate of descent (450 to 1,130 ft/sec) as long as it is aerodynamically practical are calculated and are found to be moderate in both magnitude and rate. Entry trajectories made with these types of control are presented and discussed.

Eggleston, John M.↗