Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Alloy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Evaluation of the corrosion resistance of Fe-Al-Cr alloys in simulated low NOx environments

Due to their excellent corrosion resistance, iron aluminum alloys are currently being considered for use as weld claddings in fossil fuel fired power plants. The susceptibility to hydrogen cracking of these alloys at higher aluminum concentrations has led researchers to examine the effect of chromium additions on the corrosion resistance of lower aluminum alloys. In this work, three iron aluminum alloys were exposed to simulated coal combustion environments at 500 and 700{sup o}C for short (100 h) and long (5000 h) isothermal durations. Scanning electron microscopy was used to analyze the corrosion products. All alloys exhibited excellent corrosion resistance during short term exposures. For longer test times, increasing the aluminum concentration improved alloy corrosion resistance. The addition of chromium to the binary iron aluminum alloy prevented the formation iron sulfide and resulted in slower corrosion kinetics. A general classification of the scales developed on these alloys is presented.

20 FOSSIL-FUELED POWER PLANTS↗

Characterization of phase development in non-isothermally annealed mould-cast and heat-treated Al-Mn-Sc-Zr alloys

The effect of Mn addition on microstructure and mechanical properties during isochronal annealing in the temperature range of 20 deg. C - 570 deg. C of the mould-cast and heat-treated Al-Sc-Zr alloys with a various content of Mn and Zr was studied. The electrical resistometry together with the microhardness (HV0.3) measurements were compared to microstructure development. The microstructure development was examined by scanning electron microscopy, transmission electron microscopy and electron diffraction. Relative resistivity changes and the microhardness of the mould-cast and heat-treated Al-Mn-Sc-Zr alloys exhibit similar dependence on annealing temperature. Precipitation of the Al{sub 3}Sc particles is responsible for the peak microhardness in all these alloys. The microhardness decrease is slightly delayed during the isochronal annealing and during the high temperature heat treatment in the mould-cast alloy with the higher Zr-content due to a higher oversaturation of Zr. The decomposition sequence of the oversaturated solid solution of the studied Al-Mn-Sc-Zr alloys is compatible with the recently published decomposition sequence of the Al-Sc-Zr system and also with the formation of Mn,Fe-containing particles. It seems very probable that the addition of Mn does not influence the decomposition of solid solution of the ternary Al-Sc-Zr system. - Research Highlights: {yields} Al{sub 3}Sc particles are responsible for the peak microhardness in all the studied alloys. {yields} The microhardness decrease is delayed in the alloy with the higher Zr-content. {yields} The peak hardening of the heat-treated alloys is shifted to higher temperatures. {yields} Mn does not influence the decomposition sequence of the Al-Sc-Zr system.

36 MATERIALS SCIENCE↗

Experimental Investigations on Pulsed Nd:YAG Laser Welding of C17300 Copper-Beryllium and 49Ni-Fe Soft Magnetic Alloys

Copper-beryllium and soft magnetic alloys must be joined in electrical and electro-mechanical applications. There is a high difference in melting temperatures of these alloys which cause to make the joining process very difficult. In addition, copper-beryllium alloys are of age hardenable alloys and precipitations can brittle the weld. 49Ni-Fe alloy is very hot crack sensitive. Moreover, these alloys have different heat transfer coefficients and reflection of laser beam in laser welding process. Therefore, the control of welding parameters on the formation of adequate weld puddle composition is very difficult. Laser welding is an advanced technique for joining of dissimilar materials since it can precisely control and adjust the welding parameters. In this study, a 100W Nd:YAG pulsed laser machine was used for joining 49Ni-Fe soft magnetic to C17300 copper-beryllium alloys. Welding of samples was carried out autogenously by changing the pulse duration, diameter of beam, welding speed, voltage and frequency. The spacing between samples was set to almost zero. The ample were butt welded. It was required to apply high voltage in this study due to high reflection coefficient of copper alloys. Metallography, SEM analysis, XRD and microhardness measurement was used for survey of results. The results show that the weld strength depends upon the chemical composition of the joints. To change the wells composition and heat input of the welds, it was attempted to deviate the laser focus away from the weld centerline. The best strength was achieved by deviation of the laser beam away about 0.1mm from the weld centerline. The result shows no intermetallic compounds if the laser beam is deviated away from the joint.

36 MATERIALS SCIENCE↗

Preliminary Analysis of the General Performance and Mechanical Behavior of Irradiated FeCrAl Base Alloys and Weldments

The iron-based, iron-chromium-aluminum (FeCrAl) alloys are promising, robust materials for deployment in current and future nuclear power plants. This class of alloys demonstrates excellent performance in a range of environments and conditions, including high-temperature steam (>1000°C). Furthermore, these alloys have the potential to have prolonged survival under loss-of-coolant accident (LOCA) conditions compared to the more traditional cladding materials that are either Zr-based alloys or austenitic steels. However, one of the issues associated with FeCrAl alloys is cracking during welding. The present project investigates the possibility of mitigating welding-induced cracking via alloying and precise structure control of the weldments; in the frame work of the project, several advanced alloys were developed and are being investigated prior to and after neutron irradiation to provide insight into the radiation tolerance and mechanical performance of the weldments. The present report provides preliminary results on the post-irradiation characterization and mechanical tests performed during United States Fiscal Year (FY) 2016. Chapter 1 provides a general introduction, and Chapter 2 describes the alloy compositions, welding procedure, specimen geometry and manufacturing parameters. Also, a brief discussion of the irradiation at the High Flux Isotope Reactor (HFIR) is provided. Chapter 3 is devoted to the analysis of mechanical tests performed at the hot cell facility; tensile curves and mechanical properties are discussed in detail focusing on the irradiation temperature. Limited fractography results are also presented and analyzed. The discussion highlights the limitations of the testing within a hot cell. Chapter 4 underlines the advantages of in-situ testing and discusses the preliminary results obtained with newly developed miniature specimens. Specimens were moved to the Low Activation Materials Development and Analysis (LAMDA) laboratory and prepared for mechanical tests. Tensile tests were conducted at LAMDA using a modern digital image correlation approach allowing for strain distribution analysis. Plastic strain initiation and necking are discussed in detail; a concept of strain rate maps is also introduced and discussed. Follow-on SEM-EBSD and FIBTEM analysis is planned.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Corrosion Behaviour of Al Alloys in Sea Water

The electrochemical behaviour of aluminum (Al) alloys in seawater medium was investigated using potentiodynamic technique, complemented by Scanning Electron Microscopy (SEM) and EDAX. SEM was used to characterize the corroded surface and to observe the extent of corrosion attack on the Al alloys after tested in seawater. EDAX analysis was used to identify elements present on the specimen surface. The results indicate that influences of alloying elements present in the Al alloys play important role in the corrosion of Al alloys in seawater. The behaviour of Al alloys with addition of Zn, Sn, Cu and Si was greatly enhanced in terms of its potential and corrosion behaviour. Potential of Al with alloying elements reached value more negative than -0.9 V{sub SCE} and showed active corrosion behaviour.

36 MATERIALS SCIENCE↗

Magnetic and Kinetical Properties of Fe-27%Ni-4%Mn and Fe-27%Ni-4%Mn-2%Zn Alloys Investigated by VSM and DSC

We report on the structural, thermal, and magnetic properties of thermally induced martensite in Fe-27%Ni-4%Mn and Fe-27%Ni-4%Mn-2%Zn alloys. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and vibrating sample magnetometry (VSM) techniques were employed in the present research. SEM observations revealed the lath martensite morphology formation in both Fe-27%Ni-4%Mn and Fe-27%Ni-4%Mn-2%Zn alloys. As well, the thermally induced martensite start temperature (M{sub s}) was determined to be − 27.18 °C for Fe-27%Ni-4%Mn and − 40.63 °C for Fe-27%Ni-4%Mn-2%Zn alloy from DSC measurements. Further, the Curie temperature was detected at 160 K for Fe-27%Ni-4%Mn and 196 K for Fe-27%Ni-4%Mn-2%Zn alloys after VSM measurements where magnetic saturation values were measured at 20 emu g{sup − 1} for Fe-27%Ni-4%Mn alloy and 18 emu g{sup − 1} for Fe-27%Ni-4%Mn-2%Zn alloy, respectively. The coercivity value of the alloys was also found to be 0.082 kOe for Fe-27%Ni-4%Mn and 0.050 kOe for Fe-27%Ni-4%Mn-2%Zn alloys. Finally, the effect of Zn addition to the austenite–martensite phase tarnsformations of Fe-27%Ni-4%Mn was discussed in detail according to structural, thermal, and magnetic properties of both alloys after a quantitative experimental comparison.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Processing of High-Entropy AlCoCr{sub 0.75}Cu{sub 0.5}FeNi Alloy by Spray Forming

Compositionally complex AlCoCrCuFeNi alloy system is one of the extensively studied high-entropy alloys (HEA). Most of these studies have been carried out on as-cast materials that witness slow cooling rate during solidification. In the present investigation, HEA based on AlCoCrCuFeNi system was processed employing spray forming so as to realize its inherent rapid solidification effect and unique microstructural evolution mechanism. The spray formed as well as the as-cast alloys were compared in terms of their microstructural features, phase constitution and hardness. These microstructural features were also compared with that of the overspray powders (< 250 µm) obtained as a by-product of spray forming. Both the as-cast and spray formed alloys showed a mixture of mainly two phases, i.e., face-centered and body-centered cubic (BCC) phases, in contrast to a single BCC phase in overspray powders. However, the spray formed alloy revealed unidentified phases, as against the as-cast material, which disappeared after heat treatment at 1473 K for 3 h. The grain size of the as-cast alloy was around 600-1000 μm compared to a highly refined grain size of 25-30 μm in the as-spray formed alloy. It was found that the hardness of the regions dominated by the constituent phases as well as the bulk of the spray formed material was higher than that of the as-cast alloy. The results validate the efficacy of the process in achieving drastic refinement in grain size, in a single step of large-scale spray forming. The characteristic microstructural features and the phase constitutions have been discussed in light of the prevailing mechanisms of structural evolution and possible solidification phenomena during spray atomization and deposition. This study gives a new direction in processing of these alloys and understanding their solidification behavior under the conditions of layer-by-layer deposition of semi-solid/liquid droplets.

36 MATERIALS SCIENCE↗

Electrochemical Behavior of Mg-Al-Zn-Ga Alloy as Anode Materials in 3.5 wt.% NaCl Solution

The microstructure and electrochemical behaviors of Mg-Al-Zn and Mg-Al-Zn-Ga alloys as anode materials were investigated by morphology observation, composition analysis, phase identification, and electrochemical tests. The experimental results suggest that Ga alloying can refine the grains of the Mg-Al-Zn alloy by promoting second-phase segregation, which comprises Mg{sub 17}Al{sub 12} and GaMg{sub 2}. The comparison of discharge tests indicates that adding Ga to the Mg-Al-Zn alloy can negatively shift the discharge potential, provide a high current density, promote the formation of tiny and thin products, and improve the utilization efficiency. Meanwhile, the addition of Ga can increase the corrosion resistance of Mg-Al-Zn alloy because the Ga alloying promotes the segregation of the intermetallic phases in the Mg matrix. The intermetallic phases disperse in isolate states in the Mg matrix, resulting in their falling off from the substrate once their adjacent Mg is exhausted and subsequently ceasing the micro-galvanic corrosion. The Mg-Al-Zn-Ga alloy with higher corrosion resistance performs better discharge activity than that of Mg-Al-Zn alloy in 3.5 wt.% NaCl solution, implying that the Mg-Al-Zn-Ga alloy is a promising anode material for seawater-activated battery.

36 MATERIALS SCIENCE↗

Effects of Mg Content on the Fatigue Strength and Fracture Behavior of Al-Si-Mg Casting Alloys

In order to investigate the influence of Mg content on the fatigue properties in Al-Si-Mg alloy, uniaxial tensile tests and rotating bending fatigue tests were conducted on two Al-7Si-Mg casting alloys, with different Mg contents of 0.3 and 0.6 wt.%. The fracture surfaces of the specimens were observed by scanning electron microscopy, and the fatigue crack growth process was obtained by the replica method. The results indicate that the increase in Mg content enhances the yield strength and tensile strength of the alloy, whereas it reduces its elongation. There is an obvious knee point in the S–N curves of Al-7Si-0.6Mg alloy while that of Al-7Si-0.3Mg alloy shows continuous decrease. The fatigue strength at 5 × 10{sup 5} cycles is 60 MPa for Al-7Si-0.3Mg alloy and 80 MPa for Al-7Si-0.6Mg alloy. For the two types of specimens, the fatigue failure can initiate from crystal slip and casting defects. The replica results suggest that cracks in Al-7Si-0.6Mg alloy grow more slowly than that in Al-7Si-0.3Mg alloy.

36 MATERIALS SCIENCE↗

Effect of Molybdenum Content on Structure and Properties of a Co-Cr Biomedical Alloy

The present study aimed to develop several Co-Cr biomedical alloys with different amounts of molybdenum. The weight percentages of molybdenum were in the range of 0-4 wt.% in the base alloy (Co-30Cr). The microstructures, phases, density, mechanical strength, wear behavior and corrosion characteristics of these alloys were evaluated. The results showed that density, hardness and compressive strength increased by increase in Mo content in the alloy. In contrast, corrosion rate decreased when the Mo weight percentage was increased. Furthermore, addition of Mo up to 3 wt.% caused the volumetric wear loss to increase. However, 4 wt.% Mo in the alloy led to a reduction in the volumetric wear loss, even lower than that of Co-30Cr alloy without molybdenum. The variations of friction coefficient, however, were different under different operating conditions. Since no single alloy could merely satisfy all the desired characteristics, the entropy–analytic hierarchy process (AHP)–gray relational analysis (GRA) technique was utilized to select the best alloy among the examined materials. From the ranking order gained, it was indicated that M-4 (having 4 wt.% Mo) biomedical alloy possesses the best combination of all the properties.

36 MATERIALS SCIENCE↗

Ordering effects on deformation substructures and strain hardening behavior of a CrCoNi based medium entropy alloy

Here, a CrCoNi based medium entropy alloy with small additions of Ti, Al and Nb (denoted as (CrCoNi) 93 Al 4 Ti 2 Nb) in the as-quenched condition, exhibits tensile properties comparable to those of the equiatomic CrCoNi alloy at room temperature. Dark field transmission electron microscopy (TEM), atomic resolution high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) together with atom probe tomography (APT) show that spatially-localized long range ordering (LRO) L1 2 domains exist in this alloy. The evolution of deformation substructure with plastic deformation in this alloy was characterized using electron backscatter diffraction (EBSD), electron channeling contrast imaging (ECCI) and STEM based techniques including the recently developed weak beam dark field STEM imaging. Plastic deformation occurs by the slip of a/2<110>dislocations, which are narrowly dissociated into Shockley partial dislocations on {111} slip planes. Their dissociation distances in the (CrCoNi) 93 Al 4 Ti 2 Nb alloy are much smaller than the widths of the corresponding partials in the equiatomic CrCoNi alloy due to one or more of the minor alloying elements (Al, Ti, Nb). Dislocation slip in this alloy has a pronounced planar character. The leading dislocations in slip bands glide as pairs due to the existence of LRO domains. Multipoles were formed through the slip of dislocations with opposite signs on adjacent {111} slip planes. Those multipoles serve as building blocks for the formation of subgrain structures consisting of fine slip bands. The distances between slip bands were continuously refined during plastic deformation and dynamic refinement of slip bands plays a crucial role in strain hardening. The effects of LRO domains on planar dislocation slip, the deactivation of deformation twinning and strain hardening of this alloy are discussed.

36 MATERIALS SCIENCE↗

Glass formation during combinatorial sputtering in binary alloys

Glass formation is a complex phenomenon influenced by thermodynamic and kinetic aspects, which are often controlled by extrinsic contributions. While bulk metallic glasses are typically multicomponent alloys, binary alloys offer a simplified approach to studying glass formation. In this study, we fabricated 57 binary alloy systems through combinatorial sputtering, where each alloy system is represented in 66 different alloys. We developed an automated analysis to determine structure and composition using X-ray diffraction and energy-dispersive X-ray spectroscopy for over 3700 alloys. We found that ∼17 % of the alloys form glasses under the estimated cooling rate during sputtering of ∼10 8 K/s. Data analysis revealed that commonly used factors like atomic size ratio and heat of mixing are ineffective in predicting glass formation. However, the crystal structure mismatch of the alloys’ elements emerged as the strongest indicator of glass formation under sputtering conditions of binary alloys. Here, the differences in glass formation under slow cooling rates used for bulk glass formation and the here observed glass formation under rapid cooling rates are discussed.

Binary alloys↗

Additively manufactured Al-Ce-Ni-Mn alloy with improved elevated-temperature fatigue resistance

Here, the high cycle fatigue behavior of an additively manufactured (AM) Al-10.5Ce-3.1Ni-1.2Mn wt% alloy was evaluated at 350 °C. The measured fatigue strength of 50 MPa at this temperature is comparable to the most fatigue resistant wrought Al alloys (2618-T6 and 7079-T6) at 315 °C. Refinement of pore populations through advanced AM processing in the examined alloy led to oxide inclusions becoming dominant fatigue crack initiation sites. The distribution of microstructural features that determine crack initiation was measured by X-ray computed tomography and served as input to make fatigue strength model predictions with various methodologies. A Monte-Carlo based approach that was previously applied to predict the fatigue strength of cast aluminum alloys through pore size distributions yielded accurate predictions for the fatigue strength of this AM alloy. Given the tunability of defect distributions in AM alloys, the sensitivity of the Al-Ce-Ni-Mn alloy fatigue behavior to defect distributions and outstanding elevated-temperature fatigue resistance of this alloy; the results together suggest the possibility of a new generation of fatigue-resistant alloys produced by the additive manufacturing route.

36 MATERIALS SCIENCE↗

Phase stability in cast and additively manufactured Al-rich Al-Cu-Ce alloys

Additively manufactured (AM) eutectic Al alloy systems have been studied extensively for advantageous thermal stability and mechanical properties due to their refined microstructures. Al-Cu-Ce alloys are one subset of these AM eutectic alloys. Here we studied phase stability in AM Al-Cu-Ce alloys and compared it to that of conventionally cast ones. A new phase, Al 8 Cu 3 Ce, was identified in the microstructures of both AM and cast Al-Cu-Ce alloys. This Al 8 Cu 3 Ce phase was not previously included on experimental or thermodynamically calculated phase diagrams of the Al-Cu-Ce system. Therefore, we performed additional thermodynamic modeling of the system. These models were experimentally validated with cast and subsequently heat-treated Al-Cu-Ce alloys. We found that despite the refined microstructure of the AM alloys, the phases formed were consistent with the cast alloys, suggesting that AM processing did not significantly alter the formation and stability of phases from that in the conventional alloys. In conclusion, this work has resolved inconsistent previous descriptions of the Al-Cu-Ce ternary phase diagram in the Al-rich region and resulted in the addition of the Al 8 Cu 3 Ce as an equilibrium phase above 500 °C.

36 MATERIALS SCIENCE↗

Cooling thermal parameters and microstructure features of directionally solidified ternary Sn–Bi–(Cu,Ag) solder alloys

Low temperature soldering technology encompasses Sn–Bi based alloys as reference materials for joints since such alloys may be molten at temperatures less than 180 °C. Despite the relatively high strength of these alloys, segregation problems and low ductility are recognized as potential disadvantages. Thus, for low-temperature applications, Bi–Sn eutectic or near-eutectic compositions with or without additions of alloying elements are considered interesting possibilities. In this context, additions of third elements such as Cu and Ag may be an alternative in order to reach sounder solder joints. The length scale of the phases and their proportions are known to be the most important factors affecting the final wear, mechanical and corrosions properties of ternary Sn–Bi–(Cu,Ag) alloys. In spite of this promising outlook, studies emphasizing interrelations of microstructure features and solidification thermal parameters regarding these multicomponent alloys are rare in the literature. In the present investigation Sn–Bi–(Cu,Ag) alloys were directionally solidified (DS) under transient heat flow conditions. A complete characterization is performed including experimental cooling thermal parameters, segregation (XRF), optical and scanning electron microscopies, X-ray diffraction (XRD) and length scale of the microstructural phases. Experimental growth laws relating dendritic spacings to solidification thermal parameters have been proposed with emphasis on the effects of Ag and Cu. The theoretical predictions of the Rappaz-Boettinger model are shown to be slightly above the experimental scatter of secondary dendritic arm spacings for both ternary Sn–Bi–Cu and Sn–Bi–Ag alloys examined. - Highlights: • Dendritic growth prevailed for the ternary Sn–Bi–Cu and Sn–Bi–Ag solder alloys. • Bi precipitates within Sn-rich dendrites were shown to be unevenly distributed. • Morphology and preferential region for the Ag{sub 3}Sn growth depend on Ag content and Ṫ{sub L}. • Rappaz-Boettinger model reasonably estimated the experimental scatter of λ{sub 2}.

36 MATERIALS SCIENCE↗

Molybdeno-Aluminizing of Powder Metallurgy and Wrought Ti and Ti-6Al-4V alloys by Pack Cementation process

Wear and high temperature oxidation resistance of some titanium-based alloys needs to be enhanced, and this can be effectively accomplished by surface treatment. Molybdenizing is a surface treatment where molybdenum is introduced into the surface of titanium alloys causing the formation of wear-resistant surface layers containing molybdenum, while aluminizing of titanium-based alloys has been reported to improve their high temperature oxidation properties. Whereas pack cementation and other surface modification methods have been used for molybdenizing or aluminizing of wrought and/or cast pure titanium and titanium alloys, such surface treatments have not been reported on titanium alloys produced by powder metallurgy (PM). Also a critical understanding of the process parameters for simultaneous one step molybdeno-aluminizing of titanium alloys by pack cementation and the predominant mechanism for this process have not been reported. The current research work describes the surface modification of titanium and Ti-6Al-4V prepared by PM by molybdeno-aluminizing and analyzes thermodynamic aspects of the deposition process. Similar coatings are also deposited to wrought Ti-6Al-4V and compared. Characterization of the coatings was carried out using scanning electron microscopy and x-ray diffraction. For both titanium and Ti-6Al-4V, the use of a powder pack containing ammonium chloride as activator leads to the deposition of molybdenum and aluminium into the surface but also introduces nitrogen causing the formation of a thin titanium nitride layer. In addition, various titanium aluminides and mixed titanium aluminium nitrides are formed. The appropriate conditions for molybdeno-aluminizing as well as the phases expected to be formed were successfully determined by thermodynamic equilibrium calculations. - Highlights: •Simultaneous co-deposition of Mo-Al onto powder metallurgy and wrought Ti alloy •Thermodynamic calculations were used to optimize deposition conditions •External TiN and internal a Mo-rich layer on all alloy substrates •Titanium aluminides and Ti-Al mixed nitrides are formed on Ti-6Al-4V •The presence of Al and V alloying elements modifies the diffusion of Mo.

36 MATERIALS SCIENCE↗

Friction stir welded AM50 and AZ31 Mg alloys: Microstructural evolution and improved corrosion resistance

One of the major drawbacks of Mg alloys is poor weldability, caused by porosity formation during conventional fusion welding processes. Friction Stir Welding (FSW) is promising technique in this context since it is a solid state technique. Contradicting results were published in the literature regarding the FSWed Mg alloys joint's properties. Current research was performed in order to investigate the microstructure and corrosion properties of FSWed Mg alloys, studying representatives of two commercial families: wrought AZ31-H24 and die cast AM50. It was found that in both alloys recrystallization occurred during the FSW. In AM50 the mechanism of the recrystallization was continuous, manifested by dislocation rearrangement into sub grain boundaries. In AZ31 discontinuous recrystallization had occurred through grain boundaries migration - twins rotated with respect to the matrix, turning into low angle grain boundaries. Corrosion resistance has improved during the FSW in both alloys to different extents. In the AM50 alloy, the nugget exhibited significantly higher surface potential than the base metal mainly due to the higher Al concentration in the matrix of the nugget, resulting from the dissolution of Al-enrichment and β-Mg{sub 17}Al{sub 12} phase. In the AZ31 alloy, no change in Al concentration had occurred, and the surface potential measured in the nugget was only slightly higher than in the base metal. These results underline the appropriateness of the FSW for Mg alloys since during the conventional welding deterioration of the corrosion resistance occurs. - Highlights: • Following FSW, AZ31-H24 experienced discontinuous recrystallization. • In AZ31 grain boundaries migration occurred, thus twins rotated. • In die cast AM50 continuous recrystallization occurred during the FSW. • In AM50 - dislocations rearranged into sub grain boundaries. • Corrosion resistance has improved during the FSW in both alloys to different extent.

36 MATERIALS SCIENCE↗

Effects of precipitates and its interface on thermal conductivity of Mg–12Gd alloy during aging treatment

Highlights: • Hardness and thermal conductivity of alloy can be improved by aging treatment. • The interface between precipitates and matrix transformed coherent into incoherent with increasing aging time. • Coherent interface would impede the improvement of thermal conductivity of alloy. - Abstract: How to simultaneously improve the thermal conductivity and mechanical properties of Mg alloys is an interesting and important issue topic. In the present study, the effect of aging treatment on the thermal conductivity and micro-hardness of Mg–12Gd alloy was investigated. Results indicated that the thermal conductivity and micro-hardness of the alloy could be significantly improved by aging treatment, and Mg–12Gd alloy exhibited a typical aging hardening response with the increasing aging time. At the early stage of aging (4 h), a large number of fine particles precipitated from α-Mg matrix, but thermal conductivity of alloy increased a little, which was attributed to the coherent interface hindering the increase of thermal conductivity. The thermal conductivity increased to the peak value of 75.7 W/(m·K) at the aging time of 300 h, which was about 2.17 times that of as-solutionized alloy. The huge increment in the thermal conductivity of as-aged Mg–12Gd alloy was related to the precipitation of particles and the incoherent interface between precipitates and α-Mg matrix.

36 MATERIALS SCIENCE↗