SEARCH · Engineering Papers

Results for “AFTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

All sources NASA NTRS DOE OSTI

NASA NTRS1986

Detailed near-wake flowfield surveys with comparison to an Euler method of an aspect ratio 4 rectangular wing

An experimental investigation of the flowfield in the near-wake of an aspect ratio 4 rectangular wing was conducted, providing a complete detailed set of data for use in the validation of computational methods. An angle of attack of 8 degrees and two Reynolds numbers 530,000 and 391,000 were investigated using pitot and six-hole probes. In addition, two types of flow visualization were employed. The data presented includes contours of total pressure, mean velocity, flow angularity, and vorticity distribution data at five chordwise stations of the near-wake ranging from 0.167 to 5.00 chord lengths aft of the trailing edge. The experimental results were compared to the predicted results of a 2-D Euler numerical method. The results predicted by an Euler method failed to accurately define the flowfield. Tangential velocities remained relatively constant over the range of X/C considered though increased in angle of attack and Reynolds number did bring about corresponding increases. Axial velocities also increased with angle of attack and Reynolds number but showed greater sensitivity to increases in X/C. Graphic displays and contours of the total pressure data indicate that roll-up of the wing tip vortex is essentially complete one and one half chords downstream of the trailing edge.

Klinge, M. D.↗

NASA NTRS1985

System technology analysis of aeroassisted orbital transfer vehicles. Moderate lift/drag (0.75-1.5): Volume 1A, part 2: Executive summary, phase 2

Significant achievements and activities of Phase 2 of a study to assess aeroassisted orbit transfer vehicle (AOTV) system technology are summarized. Phase 2 was directed towards identification and prioritization of technology payoffs of representative space based mid lift/drag ratio (L/D) AOTV's and the cryofueled propulsion subsystem - configuration interactions. Enhancing technology areas were identified which could provide substantial transport cost reduction. These include: (1) improved lifetime of storable propellant engines; (2) avionics weight reduction; (3) external thermal protection system weight reduction; (4) decrease of uncertainties in aerodynamic and aerothermodynamic performance; electrical power subsystem weight reduction due to incorporation of advanced materials; and (6) structural shell weight reduction. Results indicated that advanced aerothermodynamic methodology and aft end configuring may provide an enlarged allowable zone for engine nozzle protrusions into the separated flow region. Payload manifesting and non-hydrogen propellant manifesting at the space station is recommended.

Source record↗

NASA NTRS1987

Piloted-simulation study of effects of vortex flaps on low-speed handling qualities of a Delta-wing airplane

A piloted-simulation study was conducted to investigate the effects of vortex flaps on low-speed handling qualities of a delta-wing airplane. The simulation math model was developed from wind tunnel tests of a 0.15 scale model of the F-106B airplane. Pilot evaluations were conducted using a six-degree-of-freedom motion base simulator. The results of the investigation showed that the reduced static longitudinal stability caused by the vortex flaps significantly degraded handling qualities in the approach-to-landing task. Acceptable handling qualities could be achieved by limiting the aft center-of-gravity location, consequently reducing the operational envelope of the airplane. Further improvement were possible by modifying the flight control force-feel system to reduce pitch-control sensitivity.

Brandon, Jay M.↗

NASA NTRS1985

Free-jet investigation of mechanically suppressed, high radius ratio coannular plug model nozzles

The experimental and analytical acoustic results of a scale-model investigation or unsuppressed and mechanically suppressed high-radius ratio coannular plug nozzles with inverted velocity and temperature profiles are summarized. Nine coannular nozzle configurations along with a reference conical nozzle were evaluated in the Anechoic Free-Jet Facility for a total of 212 acoustic test points. Most of the tests were conducted at variable cycle engine conditions applicable to advanced high speed aircraft. The tested nozzles included coannular plug nozzles with both convergent and convergent-divergent (C-D) terminations in order to evaluate C-D effectiveness in the reduction of shock-cell noise and 20 and 40 shallow-chute mechanical suppressors in the outer stream in order to evaluate their effectiveness in the reduction of jet noise. In addition to the acoustic tests, mean and turbulent velocity measurements were made on selected plumes of the 20 shallow-chute configuration using a laser velocimeter. At a mixed jet velocity of 700 m/sec, the 20 shallow-chute suppressor configuration yielded peak aft quadrant suppression of 11.5 and 9 PNdB and forward quadrant suppression of 7 and 6 PNdB relative to a baseline conical nozzles during static and simulated flight, respectively. The C-D terminations were observed to reduce shock-cell noise. An engineering spectral prediction method was formulated for mechanically suppressed coannular plug nozzles.

Janardan, B. A.↗

NASA NTRS1986

Design and development of high strength parachutes for recovery of Filament Wound Case Space Shuttle solid rocket boosters

The Filament Wound Case (FWC) solid rocket boosters, developed for Space Shuttle launches from the West coast, are substantially lighter than their steel case counterparts, but present unique recovery system challenges due to their aft center of gravity location. This causes them to re-enter in a tail-first attitude, rather than broadside like the steel case boosters, resulting in much higher dynamic pressure at deployment. This paper outlines the differences in recovery conditions, and describes the design, development, and testing of new parachutes to meet this challenging new requirement.

Corwin, R. A.↗

NASA NTRS1987

Numerical analysis of a NACA0012 airfoil with leading edge ice accretions

Analysis of a NACA0012 airfoil with leading edge ice has been performed using a Navier-Stokes code coupled with a grid generation code. The computed results were compared to experimental information obtained for an airfoil with a well defined artificial ice shape. The computations were performed at angles of attack ranging from zero to ten degrees. This range is sufficient to show the development of the separation bubble aft of the ice shape on both the upper and lower surfaces. Velocity profile plots in the separation bubble are examined in order to determine if recirculation patterns are predicted properly and if separation and reattachment points are found within the resolution of the experimental information. Also, the massive separation near the point of stall is examined in order to more accurately evaluate the lift coefficient curve in that region. Lift, drag, and moment coefficients are computed and compared to experiment.

Potapczuk, Mark G.↗

NASA NTRS1986

Illustration of the use of modal assurance criterion to detect structural changes in an Orbiter test specimen

The analysis of empirical modal models of structural components using techniques based on the modal assurance criterion (MAC) defined by Ewins (1984) is discussed and demonstrated for the case of the Space Shuttle Orbiter aft bulkhead. Modal models of the bulkhead are constructed before and after environmental acoustic tests equivalent to 30 or 100 missions and compared (by computing their MACs) to detect significant structural changes; subdivision of the modal vector followed by computation of the MAC for each part is used to localize the changes. Numerical data demonstrating the usefulness of the MAC approach are presented in tables and diagrams.

West, Walter M.↗

NASA NTRS1986

Ten years of flight service with DC-10 composite rudders - A backward glance

Carbon-epoxy upper aft rudders have been successfully evaluated on the DC-10 during 10 years of airline flight service. They have flown for more than 320,000 flight hours, with 36,000 flight hours flown by a single rudder. The rudder box is of thin-skin buckled construction and is cocured out-of-autoclave as a one-piece assembly. Weight saving can exceed the rudder weight if full advantage is taken of removing balance weight from the forward rudder.

Hawley, Arthur V.↗

NASA NTRS1987

Acoustic results of the blade-vortex interaction acoustic test of a 40 percent model rotor in the DNW

Acoustic data of a 40 percent scale model of the 4-bladed B0-105 main rotor, measured in a large test section aeroacoustic wind tunnel, are presented. Rotor blade-vortex interaction (BVI) noise data were acquired using a traversing in-flow microphone array in the low to moderate speed flight range. Results are presented which document the flight conditions for maximum BVI impulsive noise; assess the acoustic farfield by BVI noise; map the directivity of BVI impulsive noise in a large plane below and upstream of the rotor; illustrate the temporal characteristics of the BVI signals as a function of tip-speed-ratio; and show the existence of retreating side BVI signals. The occurrence of a strongly focused radiation pattern, as opposed to a more omnidirectional pattern, was found to be very dependent on the rotor operating condition. Multiple interactions per blade were observed at the lowest speed cases, with broader impulsive content, while the higher speed cases exhibited fewer interactions per blade, with much sharper, higher amplitude acoustic signals. BVI acoustic signals were measured under the aft retreating quadrant of the rotor and found to originate from the retreating side of the rotor.

Martin, Ruth M.↗

NASA NTRS1986

An optical communication link on the Shuttle

A communication link for the transfer of data between the crew cabin and payload bay of the Shuttle is proposed. The configuration of the system, which is to transmit data optically through the Shuttle cabin window, is described. The effects of temperature cycling and cosmic radiation on optical fibers, the cable, connectors, and lenses, and of vibrations during a mission on the alignment of collimating lenses at the window are investigated. Consideration is given to determining the optimum design for the optical fiber and the optimum system operation wavelength for transmission through the aft Orbiter window and the payload environment.

Grady, Jane L.↗

NASA NTRS1986

Programmatic and technical parameters associated with Shuttle/Centaur development and operations

The cost, schedule, technical, integration, and performance parameters associated with the development of the Shuttle/Centaur configurations, Centaur G and Centaur G-Prime, for compatibility with various elements of the STS are discussed. It is noted that the design concepts for these configurations involved the use of as much flight-proven hardware from the Atlas/Centaur program as possible. Forward and aft adapters were designed using graphite/epoxy composite structures for strength, weight, and thermal flow considerations. The Centaur integrated support system serves as the system interface for all systems between the Shuttle and Centaur from prelaunch through deployment of the Centaur in LEO. As a result of the Shuttle accident of January 28, 1986, the earliest possible flight for the Centaur mission appears to be December 1987.

Clark, Harry J.↗

NASA NTRS1986

Flow rate and trajectory of water spray produced by an aircraft tire

One of the risks associated with wet runway aircraft operation is the ingestion of water spray produced by an aircraft's tires into its engines. This problem can be especially dangerous at or near rotation speed on the takeoff roll. An experimental investigation was conducted in the NASA Langley Research Center Hydrodynamics Research Facility to measure the flow rate and trajectory of water spray produced by an aircraft nose tire operating on a flooded runway. The effects of various parameters on the spray patterns including distance aft of nosewheel, speed, load, and water depth were evaluated. Variations in the spray pattern caused by the airflow about primary structure such as the fuselage and wing are discussed. A discussion of events in and near the tire footprint concerning spray generation is included.

Daugherty, Robert H.↗

NASA NTRS1987

Three-dimensional unsteady Euler solutions for propfans and counter-rotating propfans in transonic flow

An Euler code designed for computing the unsteady, three-dimensional, transonic flow about single-rotating and counter-rotating propfans using dynamic blocked-grids is presented. The algorithm is a finite volume, flux-split, upwind, implicit scheme and solves the equations which have been written in a time-dependent curvilinear coordinate system. Relative motion of the blades for counter-rotating configurations is handled by requiring that grid lines be aligned after each discrete rotation of fore and aft rotor grid blocks. The method by which information is passed across block interfaces, as well as how downstream characteristic outflow boundary conditions which enforce simple radial equilibrium are implemented, is discussed. Comparisons of computed flow-field parameters and propfan performance with experimental data indicate good overall agreement between predictions and measurements.

Whitfield, D. L.↗

NASA NTRS1987

Development and test of the Shuttle/Centaur cryogenic tankage thermal protection system

The Thermal Protection System (TPS) for the Shuttle/Centaur had to provide fail-safe thermal protection during prelaunch, launch ascent, and on-orbit operations as well as during potential abort where the Shuttle and Centaur would return to earth. The TPS selected used a helium-purged polyimide foam beneath three radiation shields for the liquid hydrogen (LH2) tank and radiation shields only for the liquid oxygen (LO2) tank (three shields on the tank sidewall and four on the aft bulkhead). An evacuated common intermediate bulkhead separated the two tanks. The LH2 tank had one 1.9-cm thick layer of foam on the forward bulkhead and two layers on the larger area side-wall. Full scale tests of the flight vehicle in a simulated Shuttle cargo bay, that was purged with gaseous nitrogen, gave total prelaunch heating rates of 25.9 kW and 12.9 kW for LH2 and LO2 tanks, respectively. Calorimeter tests on a representative LH2 tank sidewall TPS sample indicated that the measured unit heating rate would rapidly decrease from the prelaunch rate of 300 W/sq m to a desired rate of less than 4 W/sq m once on-orbit.

Knoll, R. H.↗

NASA NTRS1987

Conceptual design and integration of a Space Station resistojet propulsion assembly

The resistojet propulsion module is designed as a simple, long life, low risk system offering operational flexibility to the space station program. It can dispose of a wide variety of typical space station waste fluids by using them as propellants for orbital maintenance. A high temperature mode offers relatively high specific impulse with long life while a low temperature mode can propulsively dispose of mixtures that contain oxygen or hydrocarbons without reducing thruster life or generating particulates in the plume. A low duty cycle and a plume that is confined to a small aft region minimizes the impacts on the users. Simple interfaces with other space station systems facilitate integration. It is concluded that there are no major obstacles and many advantages to developing, installing, and operating a resistojet propulsion module aboard the Initial Operational Capability (IOC) space station.

Tacina, R. R.↗

NASA NTRS1987

High-angle-of-attack stability and control improvements for the EA-6B Prowler

The factors involved in high-angle-of-attack directional divergence phenomena for the EA-6B ECM aircraft have been investigated in NASA-Langley wind tunnel facilities in order to evaluate airframe modifications which would eliminate or delay such divergence to angles-of-attack farther removed from the operational flight envelope of the aircraft. The results obtained indicate that an adverse sidewash at the aft fuselage and vertical tail location is responsible for the directional stability loss, and that the sidewash is due to a vortex system generated by the fuselage-wing juncture. Modifications encompassing a wing inboard leading edge droop, a wing glove strake, and a vertical fin extension, have significantly alleviated the stability problem.

Jordan, Frank L.↗

NASA NTRS1987

Visualization of vortex breakdown on a delta wing

An account is given of the results obtained by a flow visualization study of the roll-up, breakdown position, and spiral- or bubble-type breakdown characteristics of an 85-deg sweep, flat-plate delta wing at large angles-of-attack. The two different breakdown modes were noted to metamorphose into each other, with the bubble-type phenomenon appearing to prefer a more upstream location relative to the spiral mode. In those instances when the breakdown location was changing, the breakdown took the form of a bubble when moving forward, and spiral when moving aft.

Nelson, R. C.↗

NASA NTRS1987

Transonic analysis and design of axisymmetric bodies in nonuniform flow

An inviscid nonuniform axisymmetric transonic code was developed for applications in analysis and design. Propfan slipstream effect on pressure distribution for a body with and without sting was investigated. Results show that nonuniformity causes pressure coefficient to be more negative and shock strength to be stronger and more rearward. Sting attached to a body reduced the pressure peak and moves the rear shock forward. Extent and Mach profile shapes of the nonuniformity region appeared to have little effect on the pressure distribution. Increasing nonuniformity magnitude made pressure coefficient more negative and moved the shock rearward. Design study was conducted with the CONMIN optimizer for an ellipsoid and a body with the NACA-0012 counter. For the ellipsoid, the general trend showed that to reduce the pressure drag, the front portion of the body should be thinner and the contour of the rear portion should be flatter than the ellipsoid. For the design of a body with a sharp trailing edge in transonic flow with an initial shape given by the NACA-0012 contour, the pressure drag was reduced by decreasing the nose radius and increasing the thickness in the aft portion. Drag reduction percentages are given.

Chang, Jen-Fu↗