Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “A. Microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,099 records · Page 61

Microstructure and Mechanical Properties of Friction Stir Welded Q235 Low-Carbon Steel

Three-millimeter-thick Q235 steel plates were friction stir welded using a tool made of tungsten-rhenium alloy in the present study. The microstructure and mechanical properties of welded joints at various traverse speeds from 50 to 150 mm/min were analyzed. It was demonstrated that traverse speed had great impacts on microstructure and mechanical properties of the joints. Phase transformation accompanied with recrystallization occurred during FSW process which resulted in different microstructures in the WNZ, and the grain size in other zones was significantly affected by traverse speed. The highest hardness was located in the nugget zone, while the lowest hardness was found in the heat-affected zone. The transverse tensile test suggested that all the joints showed slightly lower tensile strength than that of the base material, and the tensile strength increased with increasing traverse speed. All the joints fractured in the heat-affected zone with ductile fracture mode. The impact test showed that the impact toughness decreased with the increasing traverse speed and the impact fracture surface could be divided into shear lip zone and fibrous zone which showed a typical ductile fracture.

36 MATERIALS SCIENCE↗

Microstructure Evolution and Stress Corrosion Cracking Susceptibility of 12Cr Martensitic Steel Upon Long-Term Service in Power Plants

After 230,000-h long-term service at 550 °C/13.7 MPa, the microstructure of a kind of 12Cr martensitic steel was investigated using scanning electron microscopy, backscattering electron microscope and x-ray diffraction analysis. The results show that the precipitation and coarsening of carbides at grain/lath boundaries are the main cause of microstructure degradation. The static immersion tests and the slow strain rate test coupled with electrochemical impedance spectroscopy were conducted on the served steel in 1.0% NaCl solution, and it turns out that the pitting corrosion resistance and repassivation ability of the steel are significantly reduced as a result of microstructure degradation. The stress corrosion cracking susceptibility of the steel was also studied. Fracture morphology analysis shows that the secondary crack in conjunction with slip lines is a result of the coalescence of micro-cracks nucleated from the pits.

36 MATERIALS SCIENCE↗

Understanding Microstructural Evolution During Rapid Heat Treatment of Microalloyed Steels Through Computational Modeling, Advanced Physical Simulation, and Multiscale Characterization Techniques

An AISI 1045 steel modified with vanadium (V) and niobium (Nb) was studied to evaluate microstructural conditioning prior to and throughout a rapid heat treat process. In order to accomplish this, both computational and physical simulation techniques have been employed with the goal of assessing the microstructural evolution in a medium-carbon bar steel during the rapid austenitization and quenching procedures involved in an induction hardening process. The appropriate thermal profiles for induction hardening were obtained through finite element modeling using Flux 2D software. Physical simulations of the induction hardening process were carried out using a Gleeble{sup ®} 3500. Analysis of prior austenite grain size is complemented by observation of nanoscale carbonitride precipitation via transmission electron microscopy, scanning transmission electron microscopy, and high-energy synchrotron small-angle x-ray scattering. Through a combination of characterization techniques, this study presents a deeper understanding of nano- and microstructural changes occurring in a microalloyed steel during an induction hardening process.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Property Inhomogeneities of a Modified AZ80 Magnesium Alloy Wide Plate Under Horizontal Flat Die Extrusion

In the present paper, inhomogeneities in the microstructure and mechanical properties of a modified AZ80 plate under industrial production conditions were investigated. The results indicated that the microstructure of the edge and middle region shows more homogeneous and fine recrystallized grains. Additionally, more coarse recrystallized grains existed between the edge and the middle region. The ultimate tensile strength and yield strength of the edge region of the plate are maximal (287 and 162 MPa), and those near the 1/8 W region are minimal (259 and 152 MPa). The grain size increased from 19.5 to 27.2 μm along the center layer to the surface layer. The ultimate tensile stress (yield stress) increases from 258 (121 MPa) to 284 MPa (176 MPa) in the direction from the surface layer to the middle layer. The microhardness decreased from the surface layer (72HV) to the center layer (64HV). The metal strain state and temperature distribution lead to different degrees of dynamic recrystallization, which causes the microstructure and mechanical properties of the plate.

36 MATERIALS SCIENCE↗

The Effects of Sc Addition on the Microstructure and Mechanical Properties of Be-Al Alloy Fabricated by Induction Melting

This study investigated the alloying effects of 0.4 wt.% Sc on the microstructure, mechanical properties, and fracture behavior of a cast Be-Al alloy prepared by vacuum induction melting. The micromechanics of Sc-containing secondary-phase particles (SPs) were characterized by nanoindentation, and the fracture behavior of the alloy was investigated via tensile fractography and optical metallography. The addition of 0.4 wt.% Sc significantly modified the alloy microstructure by decreasing the secondary dendritic arm spacing (SDAS), weakening the dendritic structure of Be, and producing an equiaxed/cellular alloy microstructure with refined Be grains. Sc alloying increased the Vickers hardness by 36%, elastic modulus by 28%, yield strength by 35%, ultimate strength by 52%, but decreased the elongation from 3.6 to 2.9%. Sc-containing SPs had a higher elastic modulus, yield strength, microhardness, and a lower plasticity index than the Be and Al matrices, resulting in interface separation during the fracture process. SPs located at the Be/Al interfaces did not act as microcrack sources for the matrices, whereas highly faceted SPs within the Be grains induced microcrack formation and decreased the elongation. The failure mode of the cast Be-Al-0.4Sc alloy still involved the brittle cleavage failure of Be regions and ductile dimple failure of Al regions, which was not the case with the cast Be-Al alloy.

36 MATERIALS SCIENCE↗

Microstructure, Texture, and Mechanical Properties of AM60 Magnesium Alloy Processed by Extrusion and Multidirectional Forging

In the present paper, multidirectional forging (MDF), as a severe plastic deformation process, was carried out on an extruded AM60 magnesium alloy. The microstructure, texture, and mechanical properties of the MDFed samples were examined. Microstructural findings indicated that the grain size of the alloy decreased from 10.2 to 3.7 µm after six MDF passes, carried out at a constant temperature of 220 °C. Textural studies revealed that after six MDF passes, the fiber texture of the extruded material was transformed to another texture, in which the basal planes tend to rotate toward 45{sup o} to the transverse direction. Shear punch testing (SPT) was employed to assess the shear yield stress (SYS) and ultimate shear strength (USS) at room temperature. Both SYS and USS were enhanced after two MDF passes, but decreased in the next pressing stages, despite developing finer grains at higher levels of imposed strain. The observed drop in strength is ascribed to texture softening that counterbalances the grain refinement strengthening effects. The variation in average microhardness values after different passes of MDF showed the trend that was in concurrence with the rise and fall of the SPT results. Finally, the changes in mechanical properties were discussed, based on the microstructural and textural findings.

36 MATERIALS SCIENCE↗

Microstructure Evolution and Mechanical Properties of Large-Scale AZ80 Magnesium Alloy Billets Produced by Multitemperature Multidirectional Forging

Grain refinement is an effective method to improve the mechanical properties of magnesium (Mg) alloys. In the present research, the combination of multidirectional forging (MDF) and forward extrusion for sizing with decreasing temperature pass by pass was employed to deform as-cast AZ80 magnesium alloy billet with large size to obtain fine grains and homogeneous microstructure. It was found that with the increasing number of MDF passes, the average grain size decreases; the homogeneity of microstructures and the percentages of dynamic recrystallised grains increase simultaneously. After six-pass MDF, fine and homogeneous microstructure with an average grain size of 15 μm was achieved; however, grain refinement became very difficult with a further increase in the MDF pass number. After eight-pass MDF plus forward extrusion for sizing, excellent mechanical properties of large-scale AZ80 magnesium alloy billet were obtained. The tensile strength, the yield strength and the elongation of billet are 410 MPa, 292 MPa and 14%, respectively. Furthermore, during multitemperature MDF, the inverse of the square root of grain size and tensile yield strength fit well with the Hall–Petch relationship.

36 MATERIALS SCIENCE↗

Microstructure, Texture, and Mechanical Properties of Continuously Extruded and Rolled AZ31 Magnesium Alloy Sheets

It is difficult to fabricate magnesium alloy sheets at room temperature due to their hexagonal close-packed structure. In this paper, we proposed a new process that can be used to fabricate AZ31 magnesium alloy sheets with fine-grained microstructure and good mechanical properties. AZ31 magnesium alloy sheets with dimensions of 160 mm × 8 mm were obtained successfully by a continuous extrusion technique. The extruded sheets were then rolled by two different rolling routes, Route 1: the extruded sheet was heated at 350 °C and then rolled without heating of rolls and Route 2: the sheet was rolled without any previous heating by heating rolls at 280 °C. The microstructure and texture evolution as well as mechanical properties of the continuously extruded and rolled sheets were examined experimentally. The magnesium alloy sheets with relatively fine grains of 4.5-8.3 µm were obtained by continuous extrusion followed by rolling processes. The tensile strength of continuously extruded AZ31 Mg alloy sheets can be effectively increased by rolling using heating rolls (Route 2), while the ductility was enhanced by rolling heated sheets (Route 1). The mixed microstructure, consisting of refined DRX grains and deformed grains, contributes to enhancement in tensile strength of the sheet samples rolled by Route 2 due to grain-boundary strengthening and work hardening. Lower temperature and larger rolling reduction are two main factors for improving the tensile strength of AZ31magnesium alloy sheets.

36 MATERIALS SCIENCE↗

Microstructural Evolution and Toughness of the Various HAZs in 1300-MPa-Grade Ultrahigh-Strength Structural Steel

The effect of heat input on the microstructure and toughness of simulated subregions was investigated by welding thermal simulations and Charpy impact tests. The results indicate that the microstructures of the simulated coarse and fine grain heat affected zone (CGHAZ and FGHAZ) gradually changed from lath martensite to a mixture of lath martensite/lath bainite and finally to granular bainite with the increase in heat input. The microstructure of the simulated intercritical heat affected zone (ICHAZ) was mainly composed of granular bainite and blocky martensite regardless of heat input. When the heat input increased, the toughness of the simulated CGHAZ and ICHAZ continuously decreased. Nevertheless, the simulated FGHAZ still displayed good toughness (53.16 J) due to its fine structure. The occurrence of martensite-austenite (M-A) constituents was the main reason for the decrease in crack initiation energy of the simulated CGHAZ and ICHAZ at high values of heat input, and the toughness deteriorated as the size of M-A constituents increased. It should be noted that high-misorientation packet and block boundaries can effectively deviate or arrest the propagation of microcracks. When the heat input was in the approximate range of 8.63-14.95 kJ cm{sup −1}, all of the simulated subregions exhibited good toughness.

36 MATERIALS SCIENCE↗

Microstructural evolution of type 304 and 316 stainless steels under neutron irradiation at LWR relevant conditions

Extension of light water reactors' useful life will expose austenitic internal core components to irradiation damage levels beyond 100 displacements per atom (dpa), which will lead to profound microstructural evolution and consequent degradation of macroscopic properties. Microstructural evolution, including Frank loops, cavities, precipitates, and segregation at boundaries and the resultant radiation hardening in type 304 and 316 stainless steel (SS) variants, were studied in this work via experimental characterization and multiple simulation methods. Experimental data for up to 40 heats of type 304SS and 316SS variants irradiated in different reactors to 0.6–120 dpa at 275–375°C were either generated from this work or collected from literature reports. These experimental data were then combined with models of Frank loop and cavity evolution, computational thermodynamics and precipitation, and ab initio and rate theory integrated radiation-induced segregation models to provide insights into microstructural evolution and degradation at higher radiation doses.

36 MATERIALS SCIENCE↗

Direct numerical simulations in solid mechanics for quantifying the macroscale effects of microstructure and material model-form error

Two fundamental approximations in macroscale solid-mechanics modeling are (1) the assumption of scale separation in homogenization theory and (2) the use of a macroscopic plasticity material model that represents, in a mean sense, the multitude of inelastic processes occurring at the microscale. With the goal of quantifying the errors induced by these approximations on engineering quantities of interest, we perform a set of direct numerical simulations (DNS) in which polycrystalline microstructures are embedded throughout a macroscale structure. The largest simulations model over 50,000 grains. The microstructure is idealized using a randomly close-packed Voronoi tessellation in which each polyhedral Voronoi cell represents a grain. An face centered cubic crystal-plasticity model is used to model the mechanical response of each grain. The overall grain structure is equiaxed, and each grain is randomly oriented with no overall texture. The detailed results from the DNS simulations are compared to results obtained from conventional macroscale simulations that use homogeneous isotropic plasticity models. The macroscale plasticity models are calibrated using a representative volume element of the idealized microstructure. Furthermore, we envision that DNS modeling will be used to gain new insights into the mechanics of material deformation and failure.

36 MATERIALS SCIENCE↗

Composition-Dependent Microstructure-Property Relationships of Fe and Al Modified Ti-12Cr (wt.%)

b-Titanium (Ti) alloys have applications in several industries (e.g. aerospace, automotive, and biomedical) where material performance requirements vary widely. To tailor the microstructure and mechanical properties of b-Ti alloys for various applications, it is critical to understand the influence of individual alloying elements. Toward this goal, we investigated the effect of individual alloying additions on the microstructure and resultant mechanical properties of four model b-Ti alloys: Ti-12Cr, Ti-12Cr-3Al, Ti-12Cr-1Fe, and Ti-12Cr-1Fe3Al (wt.%). The microstructures of these alloys were studied using x-ray diffraction, electron microscopy, and atom probe tomography. The mechanical properties were analyzed via Vickers and Rockwell hardness measurements and tensile testing. The addition of 1 wt.% Fe resulted in an approximate 5% increase in elongation-to-failure (ef), while the addition of 3 wt.% Al did not appear to significantly affect ef. The addition of Fe and Al decreased the yield and ultimate tensile strengths.

Ballor, Joann P.↗

Evolution of Microstructure, Residual Stress, and Tensile Properties of Additively Manufactured Stainless Steel Under Heat Treatments

This study investigated the microstructure, residual stress and tensile properties of the directed energy deposited stainless steel 316L (SS316L) under thermal annealing. Microstructure characterization shows the as-printed sample has laser-generated patterns where dendritic structure is observed at the edge of the patterns and cellular structure dominates the interior region. Here, the thermal annealing at 983 and 1093°C effectively removes the dendritic/cellular structures. Synchrotron X-ray diffraction reveals that the as-fabricated SS316L exhibits compressive residual stress of -197.4 MPa. The stress is greatly relieved to -53.8 MPa after annealing at 1093°C. The room temperature tensile testing indicates that the yield strength and ultimate tensile strength drop from 378 and 502 MPa in the as-printed sample to 258 and 446 MPa in the annealed samples (1093°C), respectively. Our study provides insights into the relationship between microstructure, residual stress, and tensile properties of laser additive manufactured SS316L.

36 MATERIALS SCIENCE↗

Microstructure and Residual Stress in Functionally Graded 316L Stainless Steel/Inconel 625 Alloys Fabricated by Direct Energy Deposition

Functionally graded materials (FGMs) provide a unique solution to combine distinct properties within a single component to enhance its overall performance. Understanding the microstructure and residual stress distribution is particularly important as the material dissimilarity in FGMs can result in high residual stress that affects the mechanical integrity of structural components. Here, this work aims to study the microstructure and residual stress of additively manufactured FGMs and the effects of isothermal annealing. In this study, 316L stainless steel/Inconel 625 FGMs were built by direct energy deposition, and characterized by optical and electron microscopy as well as synchrotron-based X-ray diffraction. Our study reveals that thermal annealing at 500°C for 3 h has minimal effects on the microstructure and chemistry of the graded materials, but effectively relieves the residual stress and leads to a uniform distribution of residual stress.

36 MATERIALS SCIENCE↗

Characterization of transition carbides in quench and partitioned steel microstructures by Mössbauer spectroscopy and complementary techniques

Quenching and partitioning (Q&P) produces steel microstructures with martensite and austenite that exhibit promising property combinations for third generation advanced high strength steels. Understanding the kinetics of reactions that compete for available carbon, such as carbide formation, is critical for alloying and processing design and achieving austenite enrichment and retention during Q&P. Mössbauer effect spectroscopy (MES) was used to characterize Q&P microstructures in a 0.38C-1.54Mn-1.48Si wt.% steel after quenching to 225 °C and partitioning at 400 °C for 10 or 300 s, with an emphasis on transition carbides. The recoilless fraction for η-carbide was calculated and a correction for saturation of the MES absorption spectrum was applied, making quantitative measurements of small amounts of η-carbide, including non-stoichiometric η-carbide, possible in Q&P microstructures. Complementary transmission electron microscopy confirmed the presence of η-carbides, and MES and X-ray diffraction were used to characterize the austenite. The amount of η-carbide formed during Q&P ranged from 1.4 to 2.4 at.%, accounting for a substantial portion (~24% to 41%) of the bulk carbon content of the steel. The amount (5.0 at.%) of η-carbide that formed after quenching and tempering (Q&T) at 400 °C for 300 s was significantly greater than after partitioning at 400 °C for 300 s (2.4 at.%), suggesting that carbon partitioning from martensite to austenite occurs in conjunction with η-carbide formation during Q&P in these specimens.

36 MATERIALS SCIENCE↗

Microstructural and micromechanical characterization of IN718 theta shaped specimens built with electron beam melting

Theta-shaped specimens were additively manufactured out of Inconel 718 powders using an electron beam melting technique, as a model complex load bearing structure. We employed two different build strategies; producing two sets of specimens. Microstructural and micro-mechanical characterizations were performed using electron back-scatter, synchrotron x-ray and in-situ neutron diffraction techniques. In particular, the cross-members of the specimens were the focus of the synchrotron x-ray and in-situ neutron diffraction measurements. The build strategies employed resulted in the formation of distinct microstructures and crystallographic textures, signifying the importance of build-parameter manipulation for microstructural optimization. Large strain anisotropy of the different lattice planes was observed during in-situ loading. Texture was concluded to have a distinct effect upon both the axial and transverse strain responses of the cross-members. In particular, the (200), (220) and (420) transverse lattice strains all showed unexpected overlapping trends in both builds. This was related to the strong {200} textures along the build/loading direction, providing agreement between the experimental and calculated results.

36 MATERIALS SCIENCE↗

Twin related domains in 3D microstructures of conventionally processed and grain boundary engineered materials

The concept of twin-limited microstructures has been explored in the literature as a crystallographically constrained grain boundary network connected via only coincident site lattice (CSL) boundaries. The advent of orientation imaging has made classification of twin-related domains (TRD) or any other orientation cluster experimentally accessible in 2D using EBSD. With the emergence of 3D orientation mapping, a comparison of TRDs in measured 3D microstructures is performed in this paper and compared against their 2D counterparts. The TRD analysis is performed on a conventionally processed (CP) and a grain boundary engineered (EM) high purity copper sample that have been subjected to successive anneal procedures to promote grain growth. Finally, the EM sample shows extremely large TRDs which begin to approach that of a twin-limited microstructure, while the TRDs in the CP sample remain relatively small and remote.

36 MATERIALS SCIENCE↗

Microstructural evolution and deformation behavior of Al-Cu alloys: A Transmission X-ray Microscopy (TXM) and micropillar compression study

In this paper, a unique approach to correlating an evolving 3D microstructure in an Al-Cu alloy and its micro-scale mechanical properties has been introduced. Using these nanoscale three-dimensional microstructures derived from Transmission X-ray Microscopy (TXM), individual contributions from different strengthening mechanisms were quantified. The spatial distribution and morphology of the individual θ' and θ phases were seen to play an important role in influencing dislocation storage. Uniaxial micro-compression experiments were used to quantify the stress-strain response of the alloy at different aging times. Transmission electron microscopy (TEM) aided in discerning dislocation activity at these precipitates. A model is proposed to accurately predict the variation in yield stress by using appropriate morphological parameters from the 3D microstructure and its validity has been corroborated using experimental measurements. Distributions of 2D and 3D inter-precipitate spacing were seen to provide crucial insights on influencing deformation in such precipitation-strengthened alloys. In conclusion, the transition in deformation behavior and origin of numerous strain bursts were investigated using in situ micropillar compression testing.

36 MATERIALS SCIENCE↗