SEARCH · Engineering Papers

Results for “wake models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

All sources NASA NTRS DOE OSTI

NASA NTRS2022

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗

NASA NTRS2022

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

Roughness induced transition↗

NASA NTRS1975

A flight test investigation of the rolling moments induced on a T-37B airplane in the wake of a B-747 airplane

A flight test investigation of the B-747 vortex wake characteristics was conducted using a T-37B as a probe aircraft. The primary purpose of the program was the validation of the results of B-747 model tests which predicted significant alleviation of the vortex strength when only the inboard flaps were deflected. Measurements of the vortex-induced rolling moments of the probe aircraft showed that the predicted alleviation did occur. The effects of landing gear extension, increased lift coefficient, idle thrust, and sideslip were investigated, and all had an adverse effect on the alleviated condition as evidenced by increased induced rolling moments of the T-37B probe aircraft. Idle thrust also increased the strength of the B-747 wake vortexes with both inboard and outboard flaps extended.

Smith, H. J.↗

NASA NTRS2014

The Situational Awareness Sensor Suite for the ISS (SASSI): A Mission Concept to Investigate ISS Charging and Wake Effects

The complex interaction between the International Space Station (ISS) and the surrounding plasma environment often generates unpredictable environmental situations that affect operations. Examples of affected systems include extravehicular activity (EVA) safety, solar panel efficiency, and scientific instrument integrity. Models and heuristically‐derived best practices are well‐suited for routine operations, but when it comes to unusual or anomalous events or situations, especially those driven by space weather, there is no substitute for real‐time monitoring. Space environment data collected in real‐time (or near‐real time) can be used operationally for both real‐time alarms and data sources in assimilative models to predict environmental conditions important for operational planning. Fixed space weather instruments mounted to the ISS can be used for monitoring the ambient space environment, but knowing whether or not (or to what extent) the ISS affects the measurements themselves requires adequate space situational awareness (SSA) local to the ISS. This paper presents a mission concept to use a suite of plasma instruments mounted at the end of the ISS robotic arm to systematically explore the interaction between the Space Station structure and its surrounding environment. The Situational Awareness Sensor Suite for the ISS (SASSI) would be deployed and operated on the ISS Express Logistics Carrier (ELC) for long‐term "survey mode" observations and the Space Station Remote Manipulator System (SSRMS) for short‐term "campaign mode" observations. Specific areas of investigation include: 1) ISS frame and surface charging during perturbations of the local ISS space environment, 2) calibration of the ISS Floating Point Measurement Unit (FPMU), 3) long baseline measurements of ambient ionospheric electric potential structures, 4) electromotive force-induced currents within large structures moving through a magnetized plasma, and 5) wake‐induced ion waves in both electrostatic (i.e. particles) and electromagnetic modes. SASSI will advance the understanding of plasma‐boundary interaction phenomena, demonstrate a suite a sensors acting in concert to provide effective SSA, and validate and/or calibrate existing ISS space environment instruments and models.

Krause, L. Habash↗

NASA NTRS1973

Noise and wake structure measurements in a subsonic tip speed fan

The results of an experimental program are reported which show the effect of blade angle, tip speed, fan pressure ratio, and thrust on noise of a model fan of 0.457m (18 inches) diameter operating at subsonic tip speeds at pressure ratios between 1.06 and 1.15. The fan used in this study had 12 blades, 7 stator vanes, and a spacing between the rotor and stator of 1.85 blade chords. This fan was originally designed for aerodynamic testing and was considered a good performer. It was used in the noise test program as it incorporated features found to reduce noise in an earlier analytical parametric study. For a given pressure ratio the fan was shown to exhibit minimum noise at the blade angle and tip speed near that of maximum aerodynamic efficiency. Also, the noise level and spectrum character of this fan showed excellent correlation with scaled data of a similar larger diameter fan. Results of the program confirm the trends shown in the earlier analytical parametric study which showed that fan noise could be reduced for a given thrust and pressure ratio by increasing fan solidity, improving fan aerodynamic design, and operating the fan at an optimum subsonic tip speed. In addition to noise, the blade wake characteristics at the leading edge of the stator were measured in this program. At root and tip sections some difference between predicted and measured wakes was found. However comparisons between predicted and measured wakes at mid span locations was found to be good.

Magliozzi, B.↗

NASA NTRS1977

Viscous effects in aircraft trailing vortices

The mechanism of merging of like-signed aircraft vortices leading to a rapid redistribution of trailed vorticity in a wake through both convective and turbulent processes was investigated. Research was done experimentally in a small wind tunnel and analytically through the use of a code which computes turbulent transport using a second-order closure turbulent model. Computations are reported which demonstrate the merging phenomenon, and comparisons are made with experimental results. The usefulness of point vortex computations in predicting merging was explored. Limited computations showed that jet exhaust does not appreciably alter the merging phenomenon. The effect of ambient atmospheric turbulence on the aging of an aircraft wake was investigated at a constant turbulent dissipation rate. It was shown that under stable atmospheric conditions, when atmospheric macroscales are less than or equal to the vortex spacing, misleading results may be obtained.

Bilanin, A. J.↗

NASA NTRS1989

A defect stream function, law of the wall/wake method for compressible turbulent boundary layers

The application of the defect stream function to the solution of the two-dimensional, compressible boundary layer is examined. A law of the wall/law of the wake formulation for the inner part of the boundary layer is presented which greatly simplifies the computational task near the wall and eliminates the need for an eddy viscosity model in this region. The eddy viscosity model in the outer region is arbitrary. The modified Crocco temperature-velocity relationship is used as a simplification of the differential energy equation. Formulations for both equilibrium and nonequilibrium boundary layers are presented including a constrained zero-order form which significantly reduces the computational workload while retaining the significant physics of the flow. A formulation for primitive variables is also presented. Results are given for the constrained zero-order and second-order equilibrium formulations and are compared with experimental data. A compressible wake function valid near the wall has been developed from the present results.

Barnwell, Richard W.↗

NASA NTRS1990

Development of a defect stream function, law of the wall/wake method for compressible turbulent boundary layers

The method presented is designed to improve the accuracy and computational efficiency of existing numerical methods for the solution of flows with compressible turbulent boundary layers. A compressible defect stream function formulation of the governing equations assuming an arbitrary turbulence model is derived. This formulation is advantageous because it has a constrained zero-order approximation with respect to the wall shear stress and the tangential momentum equation has a first integral. Previous problems with this type of formulation near the wall are eliminated by using empirically based analytic expressions to define the flow near the wall. The van Driest law of the wall for velocity and the modified Crocco temperature-velocity relationship are used. The associated compressible law of the wake is determined and it extends the valid range of the analytical expressions beyond the logarithmic region of the boundary layer. The need for an inner-region eddy viscosity model is completely avoided. The near-wall analytic expressions are patched to numerically computed outer region solutions at a point determined during the computation. A new boundary condition on the normal derivative of the tangential velocity at the surface is presented; this condition replaces the no-slip condition and enables numerical integration to the surface with a relatively coarse grid using only an outer region turbulence model. The method was evaluated for incompressible and compressible equilibrium flows and was implemented into an existing Navier-Stokes code using the assumption of local equilibrium flow with respect to the patching. The method has proven to be accurate and efficient.

Wahls, Richard A.↗

NASA NTRS1974

Measurement of tilt rotor VTOL rotor wake-airframe ground aerodynamic interference for application to real time flight simulation

The hover and low speed rotor wake-airframe-ground aerodynamic characteristics of the XV-15 tilt rotor research aircraft were determined in wind tunnel tests of a scale model. Results of the wind tunnel tests were applied to real flight time simulation. The principal findings of the wind tunnel tests are summarized. The effect of aerodynamic interference on the handling qualities of the aircraft is analyzed. It was determined that aerodynamic interference effects are significant in hover and at low speeds, with the influence being more pronounced in ground effect than out of it. At airspeeds above 60 knots, aerodynamic interference does not have a significant effect on handling characteristics.

Gaffey, T. M.↗

NASA NTRS1978

Wind-tunnel testing of VTOL and STOL aircraft

The basic concepts of wind-tunnel boundary interference are discussed and the development of the theory for VTOL-STOL aircraft is described. Features affecting the wall interference, such as wake roll-up, configuration differences, recirculation limits, and interference nonuniformity, are discussed. The effects of the level of correction on allowable model size are shown to be amenable to generalized presentation. Finally, experimental confirmation of wind-tunnel interference theory is presented for jet-flap, rotor, and fan-in-wing models.

Heyson, H. H.↗

NASA NTRS1985

Computer studies of hybrid slotted working sections with minimum steady interference at subsonic speeds

Currently there is renewed interest in the evaluation and reduction of steady wind tunnel wall interference, especially for large models. Evaluation of previous predictions for perforated and slotted tunnels suggests that a hybrid slotted tunnel (i.e., a slotted tunnel with closed slats and perforated slots) should offer minimum corrections for upwash, flow curvature and solid blockage. This suggestion is confirmed by the present computer studies of a range of rectangular hybrid slotted tunnels. The computer studies are for tunnel working section height to breadth ratios of 0.835 and 0.600 over the Mach number range from 0 to 0.85. Wings swept at 28 deg and 50 deg, with ratios of model span to tunnel breadth varying from 0 to 0.7, are considered. An idealized fuselage shape is used to predict solid and wake blockage corrections for the wall configurations selected on the basis of minimum upwash and curvature interference.

Mabey, D. G.↗

NASA NTRS1988

The interaction of the solar wind with Comet Halley - Upwind and downwind

The interaction between Comet Halley and solar wind is examined using in situ data collected in 1986, computer modeling, and data from 1910, when the earth passed through the comet's tail. An overview of the nature of comets is given, presenting specific physical processes occurring in comets. The range of scientific tools and data available for studying comets is discussed. Data from observation of the comet are compared to expectations from theory and computer modeling. The data from 1910 show that the cometary tail was well developed 24 million km downstream from the nucleus with a wake about 6 million km wide.

Russell, C. T.↗

NASA NTRS1994

Airborne Windshear Detection and Warning Systems. Fifth and Final Combined Manufacturers' and Technologists' Conference, part 1

The Fifth (and Final) Combined Manufacturers' and Technologists' Airborne Windshear Review Meeting was hosted jointly by the NASA Langley Research Center (LaRC) and the Federal Aviation Administration (FAA) in Hampton, Virginia, on September 28-30, 1993. The purpose of the meeting was to report on the highly successful windshear experiments conducted by government, academic institutions, and industry; to transfer the results to regulators, manufacturers, and users; and to set initiatives for future aeronautics technology research. The formal sessions covered recent developments in windshear flight testing; windshear modeling, flight management, and ground-based systems; airborne windshear detection systems; certification and regulatory issues; development and applications of sensors for wake vortex detection; and synthetic and enhanced vision systems.

Delnore, Victor E.↗

NASA NTRS2001

Afterbody Heating Characteristics of a Proposed Mars Sample Return Orbiter

Aeroheating wind-tunnel tests were conducted on a 0.028 scale model of an orbiter concept considered for a possible Mars sample return mission. The primary experimental objectives were to characterize hypersonic near wake closure and determine if shear layer impingement would occur on the proposed orbiter afterbody at incidence angles necessary for a Martian aerocapture maneuver. Global heat transfer mappings, surface streamline patterns, and shock shapes were obtained in the NASA Langley 20-inch Mach 6 Air and CF4 Tunnels for post-normal shock Reynolds numbers (based on forebody diameter) ranging from 1,400 to 415,000, angles of attack ranging from -5 to 10 degrees at 0, 3, and 6 deg sideslip, and normal-shock density, ratios of 5 and 12. Laminar, transitional, and turbulent shear layer impingement on the cylindrical afterbody was inferred from the measurements and resulted in a localized heating maximum that ranged from 40 to 75% of the reference forebody stagnation point heating. Comparison of laminar heating prediction to experimental measurement along the orbiter afterbody highlight grid alignment challenges associated with numerical simulation of three-dimensional separated wake flows.

Horvath, Thomas J.↗

NASA NTRS2018

Acoustic Wind Tunnel Measurements of a Quadcopter in Hover and Forward Flight Conditions

An experimental testing campaign was conducted in the NASA Langley Low Speed Aeroacoustic Wind Tunnel (LSAWT) in order to better understand the acoustic characteristics of a representative quadcopter system in both hover and forward flight conditions. Aerodynamic performance measurements were acquired using a multi-axis load cell to trim the vehicle to desired thrust/lift conditions. Hover acoustic measurements provide evidence of prominent rotor-airframe interaction noise that manifests in the form of high-amplitude harmonics of the fundamental rotor blade passage frequency. Forward flight acoustic measurements of simultaneous rotor operations indicate the presence of strong forward-aft rotor wake interactions that yield increased broadband noise levels relative to cases of individual rotor operation. These results indicate the potential need for modeling complex noise generation mechanisms associated with multirotor and rotor-airframe interactions for vehicles of this class.

Zawodny, Nikolas S.↗

NASA NTRS1987

A natural low frequency oscillation in the wake of an airfoil near stalling conditions

An unusually low frequency oscillation in the flow over an airfoil was explored experimentally. Wind tunnel measurements were carried out with a two dimensional airfoil model at a chord Reynolds number of 100,000. During deep stall the usual bluff-body shedding occurred at a Strouhal number. But at the onset of stall a low frequency periodic oscillation occurred, the corresponding Strouhal number being an order of magnitude lower. The phenomenon occurred in relatively unclean flow when the freestream turbulence was raised to 0.4 percent, but did not in the cleaner flow with turbulence intensity of 0.1 percent. It could also be produced by certain high frequency acoustic excitation. Details of the flow field are compared between a case of low frequency oscillation at alpha = 15 deg and a case of bluff-body shedding at alpha = 22.5 deg. The origin of the low frequency oscillation traces to the upper surface of the airfoil and is seemingly associated with the periodic formation and breakdown of a large separation bubble. The intense flow fluctuations impart significant unsteady forces to the airfoil but diminish rapidly within a distance of one chord from the trailing edge.

Zaman, K. B. M. Q.↗

NASA NTRS1988

A natural low frequency oscillation in the wake of an airfoil near stalling conditions

Zaman, K. B. M. Q.↗

NASA NTRS2012

Extending Validated Human Performance Models to Explore NextGen Concepts

To meet the expected increases in air traffic demands, NASA and FAA are researching and developing Next Generation Air Transportation System (NextGen) concepts. NextGen will require substantial increases in the data available to pilots on the flight deck (e.g., weather,wake, traffic trajectory predictions, etc.) to support more precise and closely coordinated operations (e.g., self-separation, RNAV/RNP, and closely spaced parallel operations, CSPOs). These NextGen procedures and operations, along with the pilot's roles and responsibilities, must be designed with consideration of the pilot's capabilities and limitations. Failure to do so will leave the pilots, and thus the entire aviation system, vulnerable to error. A validated Man-machine Integration and design Analysis System (MIDAS) v5 model was extended to evaluate anticipated changes to flight deck and controller roles and responsibilities in NextGen approach and Land operations. Compared to conditions when the controllers are responsible for separation on decent to land phase of flight, the output from these model predictions suggest that the flight deck response time to detect the lead aircraft blunder will decrease, pilot scans to the navigation display will increase, and workload will increase.

Gore, Brian Francis↗