Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “system performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Mars Entry Atmospheric Data System Modeling, Calibration, and Error Analysis

The Mars Science Laboratory (MSL) Entry, Descent, and Landing Instrumentation (MEDLI)/Mars Entry Atmospheric Data System (MEADS) project installed seven pressure ports through the MSL Phenolic Impregnated Carbon Ablator (PICA) heatshield to measure heatshield surface pressures during entry. These measured surface pressures are used to generate estimates of atmospheric quantities based on modeled surface pressure distributions. In particular, the quantities to be estimated from the MEADS pressure measurements include the dynamic pressure, angle of attack, and angle of sideslip. This report describes the calibration of the pressure transducers utilized to reconstruct the atmospheric data and associated uncertainty models, pressure modeling and uncertainty analysis, and system performance results. The results indicate that the MEADS pressure measurement system hardware meets the project requirements.

Karlgaard, Christopher D.↗
NASA NTRS2020

PACE Propulsion Subsystem Surge Analysis and Testing

Propulsion subsystem surge analysis and testing was performed at NASA Goddard Space Flight Center (GSFC) in order to analytically and experimentally determine the potential for damaging dynamic pressure events in the Plankton Aerosol Cloud and ocean Ecosystem (PACE) propulsion subsystem. Surge pressures occur when propellant flow is initiated following the actuation of an isolation valve separating an upstream high pressure fluid from a downstream low pressure manifold. By design, the PACE propulsion subsystem mitigates surge pressures using an orifice, or a cavitating venturi, placed upstream of each thruster bank isolation latch valve. Venturi sizing is a balancing act due to the competing performance goals of staying within the margins of an acceptable pressure loss and maintaining surge pressures below the proof pressure rating of the subsystem components. Subsystem pressure loss is dependent upon the venturi throat diameter and is higher for smaller venturi sizes. A venturi with a smaller throat diameter incurs an increased pressure loss through the orifice resulting in a reduced thruster inlet pressure and diminished thruster performance. The PACE propulsion subsystem surge analysis and testing supports system optimization, i.e. pressure drop minimization, while still meeting the surge pressure requirements to maximize overall system performance. In this paper a new approach to surge pressure analytical gauging is discussed, as well as its accuracy when compared to traditional surge testing campaign.

Space↗
NASA NTRS1988

A unified process for systems identification based on performance assessment

Many modern spacecraft are complex multi-body dynamic systems where the bodies are connected by several active control systems for pointing and isolation. Mission requirements indicate that many structural modes and possibly some nonlinear effects will require characterization. Thus, even characterization at the subsystem level will become more difficult than usual. System level characterization difficulties will be compounded by the fact that only limited ground testing will be possible on the full up system, and flight testing will be restricted by an extremely limited measurements set. The object of the present discussion is the application of matrix majorant theory to the problem of assessing dynamic system performance when knowledge of the system is uncertain. We show how majorants provide an effective tool to relate required performance output to system identification test quality in terms of residual uncertainty in input-output relations, parameter values, nonlinearities, and interactions. The underlying machinery consists of the block-norm matrix which is a nonnegative matrix each of whose elements is the norm of a block of a suitably partitioned matrix. A matrix which bounds the block-norm matrix in the sense of nonnegative matrices, i.e., element by element is known as a majorant.

Hyland, C.↗
NASA NTRS1984

San Marco D/L solar array system design and performance

The design and performance of the solar array system for the San Marco D/L spacecraft is described in detail. The solar array system design is shown to be suitable for spacecraft which have elastically sensitized outer surfaces to measure aerodynamic forces. However, the performance of this solar array system is shown to be at least 30 percent less efficient than conventional spacecraft solar array designs. An on-board experiment to compare the in-flight performances of Si and GaAs solar cell panels is also described. Preflight performance data show that at beginning-of-life, air mass zero solar illumination, 28 C and peak power output the Si panels are at last 20 percent less efficient than the GaAs panels.

Diruscio, M.↗
NASA NTRS2011

Model-Based Diagnostics for Propellant Loading Systems

The loading of spacecraft propellants is a complex, risky operation. Therefore, diagnostic solutions are necessary to quickly identify when a fault occurs, so that recovery actions can be taken or an abort procedure can be initiated. Model-based diagnosis solutions, established using an in-depth analysis and understanding of the underlying physical processes, offer the advanced capability to quickly detect and isolate faults, identify their severity, and predict their effects on system performance. We develop a physics-based model of a cryogenic propellant loading system, which describes the complex dynamics of liquid hydrogen filling from a storage tank to an external vehicle tank, as well as the influence of different faults on this process. The model takes into account the main physical processes such as highly nonequilibrium condensation and evaporation of the hydrogen vapor, pressurization, and also the dynamics of liquid hydrogen and vapor flows inside the system in the presence of helium gas. Since the model incorporates multiple faults in the system, it provides a suitable framework for model-based diagnostics and prognostics algorithms. Using this model, we analyze the effects of faults on the system, derive symbolic fault signatures for the purposes of fault isolation, and perform fault identification using a particle filter approach. We demonstrate the detection, isolation, and identification of a number of faults using simulation-based experiments.

Daigle, Matthew John↗
NASA NTRS1990

Optimization of actuator and sensor placement for on-orbit identification in large flexible spacecraft

There has been considerable research on choosing actuator and sensor locations in large flexible spacecraft in order to optimize the controllability and observability of the system, or to maximize some objective function of control system performance. Future large flexible spacecraft may require on-orbit identification of the structure to tune the control system, because such tests cannot be performed in a one-g environment before launch. This indicates that the choice of actuator and sensor locations must serve a dual purpose, for control and for identification. This paper develops concepts for a degree of identifiability and studies placement of actuators and sensors on a free-free beam to optimize such objective functions. The results in this simple situation suggest that in free-free spacecraft structures in orbit, placement for control and placement for identification may often be consistent objectives rather than conflicting objectives.

Bergmann, Martin↗
NASA NTRS2013

A Nuclear Cryogenic Propulsion Stage for Near-Term Space Missions

The potential capability of NTP is game changing for space exploration. A first generation NCPS could provide high thrust at a specific impulse above 900 s, roughly double that of state of the art chemical engines. Near-term NCPS systems would provide a foundation for the development of significantly more advanced, higher performance systems. John F. Kennedy made his historic special address to Congress on the importance of space on May 25, 1961, "First, I believe that this nation should commit itself to achieving the goal, before this decade is out, of landing a man on the Moon and returning him safely to the Earth..." This was accomplished. John F. Kennedy also made a second request, "Secondly... accelerate development of the Rover nuclear rocket. This gives promise of some day providing a means for even more exciting and ambitious exploration of space, perhaps beyond the Moon, perhaps to the very end of the solar system itself." The investment in the Rover nuclear rocket program provided the foundation of technology that gives us assurance for greater performing rockets that are capable of taking us further into space. Combined with current technologies, the vision to go beyond the Moon and to the very end of the solar system can be realized with space nuclear propulsion and power.

Houts, Michael G.↗
NASA NTRS1989

A performance comparison between block interleaved and helically interleaved concatenated coding systems

The performance (bit-error rate vs. signal-to-noise ratio) of two different interleaving systems, block interleaving and the newer helical interleaving are compared. Both systems are studied with and without error forecasting. Without error forecasting, the two systems have identical performance. When error forecasting is used with shallow interleaving, helical interleaving gains, but less than 0.05 dB, over block interleaving. For higher interleaving depth, the systems have almost indistinguishable performance.

Cheung, K.-M.↗
NASA NTRS1993

Test model designs for advanced refractory ceramic materials

The next generation of space vehicles will be subjected to severe aerothermal loads and will require an improved thermal protection system (TPS) and other advanced vehicle components. In order to ensure the satisfactory performance system (TPS) and other advanced vehicle materials and components, testing is to be performed in environments similar to space flight. The design and fabrication of the test models should be fairly simple but still accomplish test objectives. In the Advanced Refractory Ceramic Materials test series, the models and model holders will need to withstand the required heat fluxes of 340 to 817 W/sq cm or surface temperatures in the range of 2700 K to 3000 K. The model holders should provide one dimensional (1-D) heat transfer to the samples and the appropriate flow field without compromising the primary test objectives. The optical properties such as the effective emissivity, catalytic efficiency coefficients, thermal properties, and mass loss measurements are also taken into consideration in the design process. Therefore, it is the intent of this paper to demonstrate the design schemes for different models and model holders that would accommodate these test requirements and ensure the safe operation in a typical arc jet facility.

Tran, Huy Kim↗
NASA NTRS1985

Operational performance of the photovoltaic-powered grain mill and water pump at Tangaye, Burkina Faso (formerly Upper Volta)

A photovoltaic (PV) system powering a grain mill and water pump was installed in the remote African village of Tangaye, Burkina Faso (formerly Upper Volta) under the sponsorship of the U.S. Agency for International Development (AID) and by the National Aeronautics and Space Administration (NASA) Lewis Research Center (LeRC) in early 1979. The presence reports covers the second two years of operation from April 1981 through June 1983. During this time, the grain mill and water pump were operational 96 and 88 percent of the time respectively, and the PV system generated sufficient electricity to enable the grinding of about 111 metric tons of finely ground flow and the pumping of over 5000 cm sq of water from the 10 m deep well. The report includes a description of the current configuration of the system, a review of system performance, a discussion of the socioeconomic impact of the system on the villagers and a summary of results and conclusions covering the entire four-year period.

Martz, J. E.↗
NASA NTRS2000

Performance and Optimization Metrics for Interferometric Radar

This paper provides a set of analytic equations that can be used to estimate system performance or to assist in the design of a system in that individual sources of height error can be balanced to minimize cost and maximize efficient use of resources.

optimization metrics interferometric radar interfe↗
NASA NTRS2005

INDUCTIVE SYSTEM HEALTH MONITORING WITH STATISTICAL METRICS

Model-based reasoning is a powerful method for performing system monitoring and diagnosis. Building models for model-based reasoning is often a difficult and time consuming process. The Inductive Monitoring System (IMS) software was developed to provide a technique to automatically produce health monitoring knowledge bases for systems that are either difficult to model (simulate) with a computer or which require computer models that are too complex to use for real time monitoring. IMS processes nominal data sets collected either directly from the system or from simulations to build a knowledge base that can be used to detect anomalous behavior in the system. Machine learning and data mining techniques are used to characterize typical system behavior by extracting general classes of nominal data from archived data sets. In particular, a clustering algorithm forms groups of nominal values for sets of related parameters. This establishes constraints on those parameter values that should hold during nominal operation. During monitoring, IMS provides a statistically weighted measure of the deviation of current system behavior from the established normal baseline. If the deviation increases beyond the expected level, an anomaly is suspected, prompting further investigation by an operator or automated system. IMS has shown potential to be an effective, low cost technique to produce system monitoring capability for a variety of applications. We describe the training and system health monitoring techniques of IMS. We also present the application of IMS to a data set from the Space Shuttle Columbia STS-107 flight. IMS was able to detect an anomaly in the launch telemetry shortly after a foam impact damaged Columbia's thermal protection system.

Iverson, David L.↗
NASA NTRS2001

Performance of Power Converters at Cryogenic Temperatures

Power converters capable of operation at cryogenic temperatures are anticipated to play an important role in the power system architecture of future NASA deep space missions. Design of such converters to survive cryogenic temperatures will improve the power system performance and reduce development and launch costs. Aerospace power systems are mainly a DC distribution network. Therefore, DC/DC and DC/AC converters provide the outputs needed to different loads at various power levels. Recently, research efforts have been performed at the NASA Glenn Research Center (GRC) to design and evaluate DC/DC converters that are capable of operating at cryogenic temperatures. This paper presents a summary of the research performed to evaluate the low temperature performance of five DC/DC converters. Various parameters were investigated as a function of temperature in the range of 20 to -196 C. Data pertaining to the output voltage regulation and efficiency of the converters is presented and discussed.

Elbuluk, Malik E.↗
NASA NTRS1982

Tangential blowing for control of strong normal shock - Boundary layer interactions on inlet ramps

The use of tangential blowing from a row of holes in an aft facing step is found to provide good control of the ramp boundary layer, normal shock interaction on a fixed geometry inlet over a wide range of inlet mass flow ratios. Ramp Mach numbers of 1.36 and 1.96 are investigated. The blowing geometry is found to have a significant effect on system performance at the highest Mach number. The use of high-temperature air in the blowing system, however, has only a slight effect on performance. The required blowing rates are significantly high for the most severe test conditions. In addition, the required blowing coefficient is found to be proportional to the normal shock pressure rise.

Schwendemann, M. F.↗
NASA NTRS1981

Advanced oxygen-hydrocarbon Earth-to-orbit propulsion

Liquid oxygen/hydrocarbon (LO2/HC) rocket engine cycles for a surface to orbit transportation system were evaluated. A consistent engine system data base is established for defining advantages and disadvantages, system performance and operating limits, engine parametric data, and technology requirements for candidate engine systems. Preliminary comparisons of the engine cycles utilizing delivered specific impulse values are presented. Methane and propane staged combustion cycles are the highest LO2/HC performers. The hydrogen cooled LO2/methane dual throat engine was found to be the highest performing. Technology needs identified in the study include: high temperature turbines; oxidizer-rich preburners; LO2, methane, and propane cooling; methane and propane fuel-rich preburners; the HC fuel turbopump; and application of advanced composite materials to the engine system. Parametric sensitivity analysis data are displayed which show the effect of variations in engine thrust, mixture ratio, chamber pressure, area ratio, cycle life, and turbine inlet temperature on specific impulse and engine weight.

Obrien, C. J.↗
NASA NTRS2015

Methods for LEO Testing of CubeSat Propulsion Systems

Low Earth Orbit is becoming an inexpensive and readily available technology demonstration environment. Many new CubeSat technologies are taking advantage of this as an economical mechanism to advance beyond TRL 5. A wave of CubeSat propulsion systems favoring both reaction control and primary thrust will approach TRL 5 over the coming years, with some already there. These propulsion systems cover a wide range of capabilities including taking CubeSats to interplanetary destinations. In order to determine the feasibility of using LEO to validate the propulsion system performance and in doing so raising the TRL, a variety of factors need to be addressed. These factors include: method of measurement, environmental disturbances, spacecraft control states, and spacecraft mass properties. Propulsion Pathfinder is a NASA Ames Research Center lead project focused on raising the TRL of multiple propulsion systems over a series of flights in the coming years. This paper will highlight a few of the methods of measurement considered by this project to validate the performance of a propulsion system. The measurement methods range from tracking acceleration andor wheel spin-up to monitoring Two Line Elements between thrusting and non thrusting states. Focus will then be placed on the uncertainty of the measurement method and subsequently its feasibility through an analysis of LEO disturbance environment models and common CubeSat mass properties. In addition, the primary spacecraft control states and their imposition from the propulsion system are assessed.

Feasibility↗