Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “stability constraint”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Use of Traffic Intent Information by Autonomous Aircraft in Constrained Operations

This paper presents findings of a research study designed to provide insight into the issue of intent information exchange in constrained en-route air-traffic operations and its effect on pilot decision-making and flight performance. The piloted simulation was conducted in the Air Traffic Operations Laboratory at the NASA Langley Research Center. Two operational modes for autonomous flight management were compared under conditions of low and high operational complexity (traffic and airspace hazard density). The tactical mode was characterized primarily by the use of traffic state data for conflict detection and resolution and a manual approach to meeting operational constraints. The strategic mode involved the combined use of traffic state and intent information, provided the pilot an additional level of alerting, and allowed an automated approach to meeting operational constraints. Operational constraints applied in the experiment included separation assurance, schedule adherence, airspace hazard avoidance, flight efficiency, and passenger comfort. The strategic operational mode was found to be effective in reducing unnecessary maneuvering in conflict situations where the intruder's intended maneuvers would resolve the conflict. Conditions of high operational complexity and vertical maneuvering resulted in increased proliferation of conflicts, but both operational modes exhibited characteristics of stability based on observed conflict proliferation rates of less than 30 percent. Scenario case studies illustrated the need for maneuver flight restrictions to prevent the creation of new conflicts through maneuvering and the need for an improved user interface design that appropriately focuses the pilot's attention on conflict prevention information. Pilot real-time assessment of maximum workload indicated minimal sensitivity to operational complexity, providing further evidence that pilot workload is not the limiting factor for feasibility of an en-route distributed traffic management system, even under highly constrained conditions.

Wing, David J.↗

Meteoroid Impact Detection for Exploration of Asteroids (MIDEA)

Asteroids contain a wealth of resources including water and precious metals that can be extracted. These resources could be applied to in-space manufacture of products that depend less on material launched from Earth's surface. The Meteoroid Impact Detection for Exploration of Asteroids (MIDEA) concept addresses the challenge of characterizing an asteroid surface using a small satellite with a constellation of free-flying plasma sensors to assess the asteroid’s viability for in situ resource utilization (ISRU). The plasma sensors detect ions ejected from the surface of an asteroid by meteoroid impacts, enabling the surface composition to be inferred. The objective of this NIAC Phase I study was to demonstrate feasibility of the MIDEA architecture in the context of proximity operations around an asteroid target and to develop the design of an orbital geometry and attitude control strategy for the ultralight plasma sensors. This was undertaken through a simulation framework to identify and characterize a favorable orbit for the MIDEA sensor constellation, and developing a sensor geometry that is consistent with maintaining the pointing requirements necessary to operate with sufficient power generation. Our study showed that a polar orbit aligned along the asteroid terminator provided sufficient stability for the sensors in the low gravitational environment under the influence of substantial solar radiation pressure. Reflector vanes using controlled reflectivity devices implemented with liquid crystal technology are capable of maintaining the sensor attitude so that it consistently points its solar panels in the sun direction and the sensor electrode at the asteroid surface. Finally, the reduction in meteoroid impact detection due to visibility constraints from the proposed orbit does not substantially extend the expected mission duration. These results indicate that the MIDEA concept can be achievable using a 10–20 kg spacecraft, which would be able to characterize the surface composition of an asteroid within 30–50 days of proximity operations. This architecture, implemented in parallel to multiple asteroid targets, would enable widespread exploration of near-Earth asteroids at low cost.

Asteroids↗

Rapid evolution of stability and productivity at the origin of a microbial mutualism

Mutualistic interactions are taxonomically and functionally diverse. Despite their ubiquity, the basic ecological and evolutionary processes underlying their origin and maintenance are poorly understood. A major reason for this has been the lack of an experimentally tractable model system. We examine the evolution of an experimentally imposed obligate mutualism between sulfate-reducing and methanogenic microorganisms that have no known history of prior interaction. Twenty-four independent pairings (cocultures) of the bacterium Desulfovibrio vulgaris and the archaeon Methanococcus maripaludis were established and followed for 300 community doublings in two environments, one allowing for the development of a heterogeneous distribution of resources and the other not. Evolved cocultures grew up to 80percent faster and were up to 30percent more productive (biomass yield per mole substrate) than the ancestors. The evolutionary process was marked by periods of significant instability leading to extinction of two of the cocultures, but resulted in more stable, efficient, and productive mutualisms for most replicated pairings. Comparisons of evolved cocultures with those assembled from one evolved and one ancestral mutualist showed that evolution of both species contributed to improved productivity. Surprisingly, however, overall improvements in growth rate and yield were less than the sum of individual contributions, suggesting antagonistic interactions between mutations from the coevolved populations. Physical constraints on the transfer of metabolites in the evolution environment affected the evolution of M. maripaludis but not D. vulgaris. Together, these results show that challenges can imperil nascent obligate mutualisms and demonstrate the evolutionary responses that enable their persistence and future evolution.

60 APPLIED LIFE SCIENCES↗

A HOT AND MASSIVE ACCRETION DISK AROUND THE HIGH-MASS PROTOSTAR IRAS 20126+4104

We present new spectral line observations of the CH{sub 3}CN molecule in the accretion disk around the massive protostar IRAS 20126+4104 with the Submillimeter Array, which, for the first time, measure the disk density, temperature, and rotational velocity with sufficient resolution (0.″37, equivalent to ∼600 au) to assess the gravitational stability of the disk through the Toomre- Q parameter. Our observations resolve the central 2000 au region that shows steeper velocity gradients with increasing upper state energy, indicating an increase in the rotational velocity of the hotter gas nearer the star. Such spin-up motions are characteristics of an accretion flow in a rotationally supported disk. We compare the observed data with synthetic image cubes produced by three-dimensional radiative transfer models describing a thin flared disk in Keplerian motion enveloped within the centrifugal radius of an angular-momentum-conserving accretion flow. Given a luminosity of 1.3 × 10{sup 4} L {sub ⊙}, the optimized model gives a disk mass of 1.5 M {sub ⊙} and a radius of 858 au rotating about a 12.0 M {sub ⊙} protostar with a disk mass accretion rate of 3.9 × 10{sup −5} M {sub ⊙} yr{sup −1}. Our study finds that, in contrast to some theoretical expectations, the disk is hot and stable to fragmentation with Q > 2.8 at all radii which permits a smooth accretion flow. These results put forward the first constraints on gravitational instabilities in massive protostellar disks, which are closely connected to the formation of companion stars and planetary systems by fragmentation.

79 ASTRONOMY AND ASTROPHYSICS↗

Equation of state and strength of diamond in high-pressure ramp loading

Diamond is used extensively as a component in high-energy-density experiments, but existing equation of state (EOS) models do not capture its observed response to dynamic loading. In particular, in contrast with first-principles theoretical models of equilibrium multiphase EOS, no solid-solid phase changes have been detected, and no general-purpose EOS models match the measured ambient isotherm. We have performed density functional theory (DFT) calculations of the diamond phase to ~10 TPa, well beyond its predicted range of thermodynamic stability, and used these results as the basis of a Mie-Grüneisen EOS. We also performed DFT calculations of the elastic moduli, and calibrated an algebraic elasticity model for use in simulations. We then estimated the flow stress of diamond by comparison with the stress-density relation measured experimentally in ramp-loading experiments. Furthermore, the resulting constitutive model allows us to place a constraint on the Taylor-Quinney factor (the fraction of plastic work converted to heat) from the observation that diamond does not melt on ramp compression.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nonstoichiometric Salt Intercalation as a Means to Stabilize Alkali Doping of 2D Materials

Although doping with alkali atoms is a powerful technique for introducing charge carriers into physical systems, the resulting charge-transfer systems are generally not air stable. Here, in this paper, we describe computationally a strategy towards increasing the stability of alkali-doped materials that employs stoichiometrically unbalanced salt crystals with excess cations (which could be deposited during, e.g., in situ gating) to achieve doping levels similar to those attained by pure alkali metal doping. The crystalline interior of the salt crystal acts as a template to stabilize the excess dopant atoms against oxidation and deintercalation, which otherwise would be highly favorable. We characterize this doping method for graphene, NbSe 2 , and Bi 2 Se 3 and its effect on direct-to-indirect band gap transitions, 2D superconductivity, and thermoelectric performance. Salt intercalation should be generally applicable to systems which can accommodate this “ionic crystal” doping (and particularly favorable when geometrical packing constraints favor nonstoichiometry).

2-dimensional systems↗

Fast Solution of Fully Implicit Runge--Kutta and Discontinuous Galerkin in Time for Numerical PDEs, Part II: Nonlinearities and DAEs

Fully implicit Runge--Kutta (IRK) methods have many desirable accuracy and stability properties as time integration schemes, but high-order IRK methods are not commonly used in practice with large-scale numerical PDEs because of the difficulty of solving the stage equations. This paper introduces a theoretical and algorithmic framework for solving the nonlinear equations that arise from IRK methods (and discontinuous Galerkin discretizations in time) applied to nonlinear numerical PDEs, including PDEs with algebraic constraints. Several new linearizations of the nonlinear IRK equations are developed, offering faster and more robust convergence than the often-considered simplified Newton, as well as an effective preconditioner for the true Jacobian if exact Newton iterations are desired. Inverting these linearizations requires solving a set of block 2 x 2 systems. Under quite general assumptions, it is proven that the preconditioned 2 x 2 operator's condition number is bounded by a small constant close to one, independent of the spatial discretization, spatial mesh, and time step, and with only weak dependence on the number of stages or integration accuracy. Moreover, the new method is built using the same preconditioners needed for backward Euler-type time stepping schemes, so can be readily added to existing codes. The new methods are applied to several challenging fluid flow problems, including the compressible Euler and Navier--Stokes equations, and the vorticity-streamfunction formulation of the incompressible Euler and Navier--Stokes equations. Up to 10th-order accuracy is demonstrated using Gauss IRK, while in all cases fourth-order Gauss IRK requires roughly half the number of preconditioner applications as required by standard Singly diagonally implicit Runge--Kutta methods.

97 MATHEMATICS AND COMPUTING↗

Relaxation of magnetotail plasmas

A quasi-thermodynamic model is presented for the relaxation of magnetotail plasmas during substorms, followed by quiet times. It is proposed that the plasma relaxes to a state of low-potential energy subject to a small number of global constraints. The constraints are exactly preserved by all ideal motions and, approximately, by a wide class of motions of the plasma undergoing magnetic reconnection. A variational principle which minimizes the free energy predicts the relaxed state. Exact, two-dimensional solutions of the relaxed state are obtained. A universal feature of the exact solutions is a chain of magnetic islands along the tail axis. Sufficient conditions for the stability of relaxed states are obtained from the second variation of the free-energy functional.

Bhattacharjee, A.↗

Progress in GaAs/CuInSe2 tandem junction solar cells

Much more power is required for spacecraft of the future than current vehicles. To meet this increased demand for power while simultaneously meeting other requirements for launch, deployment, and maneuverability, the development of higher-efficiency, lighter-weight, and more radiation resistant photovoltaic cells is essential. Mechanically stacked tandem junction solar cells based on (AlGaAs)GaAs thin film CLEFT (Cleavage of Lateral Epitaxial Film for Transfer) top cells and CuInSe2(CIS) thin film bottom cells are being developed to meet these power needs. The mechanically stacked tandem configuration is chosen due to its interconnect flexibility allowing more efficient array level performance. It also eliminates cell fabrication processing constraints associated with monolithically integrated multi-junction approaches, thus producing higher cell fabrication yields. The GaAs cell is used as the top cell due to its demonstrated high efficiency, and good radiation resistance. Furthermore, it offers a future potential for bandgap tuning using AlGaAs as the absorber to maximize cell performance. The CuInSe2 cell is used as the bottom cell due to superb radiation resistance, stability, and optimal bandgap value in combination with an AlGaAs top cell. Since both cells are incorporated as thin films, this approach provides a potential for very high specific power. This high specific power (W/kg), combined with high power density (W/sq m) resulting from the high efficiency of this approach, makes these cells ideally suited for various space applications.

Kim, N. P.↗

Enabling the Next Generation of Spaceborne Quadrupole Mass Spectrometers

The quadrupole mass spectrometer (QMS) has over 30 years of spaceflight heritage in making important neutral gas and low energy ion observations. Given their geometrical constraints, these instruments are currently operated at the extreme limit of their capabilities. However, a technique called higher order auxiliary excitation provides a set of novel, robust, electronics-based solutions for improving the performance of these sensors. By driving the quadrupole rods with an additional frequency nearly twice that of the normal RF operating frequency, substantially increased abundance sensitivity, maximum attainable mass resolution, and peak stability can be achieved through operation of voltage scan lines through the center of formed upper stability islands. Such improvements are modeled using numerical simulations of ion trajectories in a quadrupole field with and without applied higher order auxiliary excitation. When compared to a traditional QMS with a mass range up to 500Da, sensors can be designed with the same precision electronics to have expected mass ranges beyond 1500Da with a power increase of less than twice that of its heritage implementations.

Gershman, D. J.↗

Working Fluid Trade Study for a Two-Phase Mechanically Pumped Loop Thermal Control System

NASA Jet Propulsion Laboratory is investigating a two-phase mechanically pumped fluid loop (MPFL) technology for spacecraft thermal control for future planetary space science mission concepts. The two-phase technology combines the potential of single-phase MPFL and the passive two-phase heat pipe systems. Previous two-phase MPFL studies at JPL have identified an evaporator system with a separated flow architecture as providing a robust light mass thermal control system with very high spatial and temporal thermal stability required by the science instruments on these missions. These studies have further identified the thermophysical properties of the working fluid to be key to the performance of a two-phase fluid loop. This paper describes the methodology used in the selection of the working fluids for optimizing the performance of the two-phase MPFL. A high level model was developed that includes the constraints and boundaries driven by the system components. The performance of fluids from the REFPROP database are investigated and rated for this system. The working fluid attributes such as cost, hazardous properties, and heritage were taken into account in this selection. A typical spacecraft dissipating 1000 W and a fluid loop consisting of an evaporator, accumulator, radiator, and associated tubing components is used as an example in this study.

Daimaru, Takuro↗

Working Fluid Trade Study for a Two-Phase Mechanically Pumped Loop Thermal Control System

NASA Jet Propulsion Laboratory is investigating a two-phase mechanically pumped fluid loop (MPFL) technology for spacecraft thermal control for future planetary space science mission concepts. The two-phase technology combines the potential of single-phase MPFL and the passive two-phase heat pipe systems. Previous two-phase MPFL studies4,5 at JPL have identified an evaporator system with a separated flow architecture as providing a robust light mass thermal control system with very high spatial and temporal thermal stability required by the science instruments on these missions. These studies have further identified the thermophysical properties of the working fluid to be key to the performance of a two-phase fluid loop. This paper describes the methodology used in the selection of the working fluids for optimizing the performance of the two-phase MPFL. A high level model was developed that includes the constraints and boundaries driven by the system components. The performance of fluids from the REFPROP database were investigated and rated for this system. The working fluid attributes such as cost, hazardous properties, and heritage were taken into account in this selection. A typical spacecraft dissipating 1000 W and a fluid loop consisting of an evaporator, accumulator, radiator, and associated tubing components was used as an example in this study.

Daimaru, Takuro↗

A precision test of averaging in AdS/CFT

We reconsider the role of wormholes in the AdS/CFT correspondence. We focus on Euclidean wormholes that connect two asymptotically AdS or hyperbolic regions with $\mathbb{S}$ 1 × $\mathbb{S}$ d-1 boundary. There is no solution to Einstein’s equations of this sort, as the wormholes possess a modulus that runs to infinity. To find on-shell wormholes we must stabilize this modulus, which we can do by fixing the total energy on the two boundaries. Such a wormhole gives the saddle point approximation to a non-standard problem in quantum gravity, where we fix two asymptotic boundaries and constrain the common energy. Crucially the dual quantity does not factorize even when the bulk is dual to a single CFT, on account of the fixed energy constraint. From this quantity we extract a smeared version of the microcanonical spectral form factor. For a chaotic theory this quantity is self-averaging, i.e. well-approximated by averaging over energy windows, or over coupling constants. We go on to give a precision test involving the microcanonical spectral form factor where the two replicas have slightly different coupling constants. In chaotic theories this form factor is known to smoothly decay at a rate universally predicted in terms of one replica physics, provided that there is an average either over a window or over couplings. We compute the expected decay rate for holographic theories, and the form factor from a wormhole, and the two exactly agree for a wide range of two-derivative effective field theories in AdS. This gives a precision test of averaging in AdS/CFT. Our results interpret a number of confusing facts about wormholes and factorization in AdS and suggest that we should regard gravitational effective field theory as a mesoscopic description, analogous to semiclassical mesoscopic descriptions of quantum chaotic systems.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Explainable tokamak-agnostic forecasting of fusion plasma instability via megahertz turbulent fluctuations

Scientific applications of artificial intelligence (AI) often remain limited by device-specific training and unexplained “black-box” approaches, creating fundamental barriers to cross-system generalization. This challenge is critical for nuclear fusion, where future reactors will have limited operational data for AI training. Here, we demonstrate that our neural network, trained solely on megahertz-scale turbulence measurements from one machine (DIII-D), forecasts Type-I edge localized mode (ELM) onsets in a different tokamak (KSTAR) through zero-shot weight transfer following physics-consistent preprocessing without device-specific retraining. Through an explainable AI framework combining gradient-weighted class activation mapping with physics validation, we reveal that our network can internalize physics relationships governing the ELM instabilities rather than memorizing device-specific patterns. The network perceives spatiotemporal features that correlate consistently with independently calculated instability growth rates, magnetohydrodynamic stability limits, and pedestal structure dynamics. Statistical analyses of dimensionally-reduced saliency features reveal the identical triangular features between the saliency representations, instability growth rates, and prediction probability across tokamaks, providing evidence that our forecasting system can show tokamak-agnostic generalization. This work contributes to a foundation for explainable scientific AI systems, where cross-system developments are essential for transcending traditional domain-specific constraints.

AI↗

Enabling cooperative adaptive cruise control on strings of vehicles with heterogeneous dynamics and powertrains

Recent studies have shown that positive impact of Cooperative Adaptive Cruise Control (CACC) can only be guaranteed as market penetration rate increases. Removing the string homogeneity constraint is essential to encourage widespread adoption. In this work, a hierarchical architecture is proposed to enable CACC on vehicles with not only mixed dynamics but also different powertrain types. A low-level layer deals with the vehicle and powertrain dynamics to provide accurate and consistent reference speed tracking response. The high-level layer uses: (1) a Linear Parameter Varying feedback system to provide loop stability, robustness and enforce a variable time gap policy and (2) a feedforward system that processes Vehicle-to-Vehicle information to enhance string stability and response bandwidth, by dealing with the string heterogeneity. A gap management strategy is built on top of the CACC architecture to handle gap setting changes or cut-in/out situations, via a dynamics constrained time gap trajectory planning algorithm. We report the proposed work has been designed, developed and validated on three different real passenger vehicles on public highways and test tracks, showing the potential of the proposed algorithm to enable robust string stable CACC, despite the different dynamics and powertrains considered.

33 ADVANCED PROPULSION SYSTEMS↗

Parabolized stability equations

The parabolized stability equations (PSE) are a new approach to analyze the streamwise evolution of single or interacting Fourier modes in weakly nonparallel flows such as boundary layers. The concept rests on the decomposition of every mode into a slowly varying amplitude function and a wave function with slowly varying wave number. The neglect of the small second derivatives of the slowly varying functions with respect to the streamwise variable leads to an initial boundary-value problem that can be solved by numerical marching procedures. The PSE approach is valid in convectively unstable flows. The equations for a single mode are closely related to those of the traditional eigenvalue problems for linear stability analysis. However, the PSE approach does not exploit the homogeneity of the problem and, therefore, can be utilized to analyze forced modes and the nonlinear growth and interaction of an initial disturbance field. In contrast to the traditional patching of local solutions, the PSE provide the spatial evolution of modes with proper account for their history. The PSE approach allows studies of secondary instabilities without the constraints of the Floquet analysis and reproduces the established experimental, theoretical, and computational benchmark results on transition up to the breakdown stage. The method matches or exceeds the demonstrated capabilities of current spatial Navier-Stokes solvers at a small fraction of their computational cost. Recent applications include studies on localized or distributed receptivity and prediction of transition in model environments for realistic engineering problems. This report describes the basis, intricacies, and some applications of the PSE methodology.

Herbert, Thorwald↗

Control of mechanical systems with rolling constraints: Application to dynamic control of mobile robots

There are many examples of mechanical systems that require rolling contacts between two or more rigid bodies. Rolling contacts engender nonholonomic constraints in an otherwise holonomic system. In this article, we develop a unified approach to the control of mechanical systems subject to both holonomic and nonholonomic constraints. We first present a state space realization of a constrained system. We then discuss the input-output linearization and zero dynamics of the system. This approach is applied to the dynamic control of mobile robots. Two types of control algorithms for mobile robots are investigated: trajectory tracking and path following. In each case, a smooth nonlinear feedback is obtained to achieve asymptotic input-output stability and Lagrange stability of the overall system. Simulation results are presented to demonstrate the effectiveness of the control algorithms and to compare the performane of trajectory-tracking and path-following algorithms.

Sarkar, Nilanjan↗

Role of Biochar in Mitigation of Climate Change

By virtue of the large fraction of the terrestrial carbon (C) cycle controlled by human activities, agroecosystems are both sources and sinks for greenhouse gases. Their potential role in mitigation of climate change thus depends on a dual strategy of decreasing greenhouse gas emissions while increasing sinks so that the net impact on climate warming is less than at present. Emissions of carbon dioxide, methane and nitrous oxide arise from various agricultural activities, ranging from land clearing to ploughing, fertilization, and animal husbandry. Reductions in these emissions can be achieved by decreasing the heterotrophic conversion of organic C to carbon dioxide, and by better management of agricultural waste streams to minimize release of methane and nitrous oxide. Current sinks include C stored in standing biomass and soil organic matter, and the oxidation of atmospheric methane by soil bacteria. These sinks can be enhanced by increasing net primary productivity, thereby actively withdrawing more carbon dioxide from the atmosphere, and by promoting more oxidation of methane by soils. Judicious biochar management may contribute to both strategies, reductions of emissions by agriculture and active withdrawal of atmospheric carbon dioxide, as part of a comprehensive scheme in agricultural and forestry watersheds. Biochar is a carbon-rich organic material generated by heating biomass in the absence, or under a limited supply, of oxygen. This so-called charring or pyrolysis process has been used to produce charcoal as a source of fuel for millennia. Recently, interest has grown in understanding the potential of this process to improve soil health by adding biochar as an amendment to soil, to manage agricultural and forestry wastes, to generate energy, to decrease net emissions of nitrous oxide and methane, and to store carbon (C). The main incentive of biochar systems for mitigation of climate change is to increase the stability of organic matter or biomass. This stability is achieved by the conversion of fresh organic materials, which mineralize comparatively quickly, into biochar, which mineralizes much more slowly. The difference between the mineralization of uncharred and charred material results in a greater amount of carbon storage in soils and a lower amount of carbon dioxide, the major greenhouse gas, in the atmosphere. The principle of creating and managing biochar systems may address multiple environmental constraints. Biochar may help not only in mitigating climate change, but also fulfill a role in management of agricultural and forestry wastes, enhancement of soil sustainability, and generation of energy. Pyrolysis is a comparatively low-technology intervention. Deployment on a global scale, however, must be done carefully if the full mitigation potential is to be reached. Critical aspects of a successful implementation are that: 1) the biochar is sufficiently stable to reduce greenhouse gases in the atmosphere for an appropriate length of time. 2) the storage of carbon as biochar in soil is not offset by greenhouse gas emissions along the value chain of the system, such as mineralization of soil carbon or emissions of other greenhouse gases (e.g., methane and nitrous oxide). 3) net emission reductions are achieved for the entire life cycle of the system including indirect land use. 4) the biochar product does not cause unwanted side effects in soil. 5) the handling and production of biochar are in compliance with health and safety standards and do not pose hurdles to implementation. and 6) the biochar system is financially viable. This chapter discusses these issues in separate sections, identifies knowledge gaps, and proposes a road map to fully evaluate an environmentally and socially safe exploration of the biochar potential to mitigate climate change if adopted widely around the world.

03 NATURAL GAS↗