Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “moderator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Extracting a mixing parameter from 2D radiographic imaging of variable-density turbulent flow

We extract a suitably averaged fluctuating density from the two-dimensional radiographic image of a flow. The X-ray attenuation is given by the Beer–Lambert law which exponentially damps the incident beam intensity by a factor proportional to the density, opacity and thickness of the target. By making reasonable assumptions for the mean density, opacity and effective thickness of the target flow, we estimate the density fluctuation contribution to the attenuation. The extracted density fluctuations averaged across the thickness of the flow in the direction of the beam may be used to form the density–specific-volume correlation $b$. In a statistical description of variable-density turbulence, $b$ quantifies the degree of mixedness. The ability to extract a measure of mixedness from experimental data would be a powerful tool that could be used in the validation of mix models. The scheme proposed is tested for DNS data computed for variable density buoyancy-driven mixing. We quantify the deficits in the extracted value of $b$ due to target thickness, Atwood number and modeled signal noise. This analysis justifies using the proposed scheme to infer the mix parameter from thin targets at moderate to low Atwood numbers. Furthermore, to illustrate how the scheme might be used in a practical problem, we demonstrate its application to a radiographic image of counter-shear flow obtained from experiments at the National Ignition Facility.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Physical mechanisms for the transition from type-III to large ELMs induced by impurity injection on EAST

Transition from type-III to large-amplitude ELMs induced by neon injection has been observed in the EAST tokamak at overlapping q 95 space between large and small ELMs. With neon injection, pedestal density gradient shows a remarkable increase accompanied by some decrease of pedestal electron temperature, and consequently the pressure gradient increases moderately and edge bootstrap current has minimal change. Further experiment demonstrates that the occurrence of large ELMs after neon injection is highly correlated with the change in edge density. Linear peeling-ballooning stability analysis indicates that the large ELM case is more unstable than the type-III ELM case during the ELM transition. A scan of pedestal density gradient in linear stability analysis shows that the direct destabilizing effect of steep pedestal density gradient on peeling-ballooning instabilities via two-fluid effects could also facilitate the transition to large ELMs. In conclusion, these results could provide more insight into the role of pedestal density gradient on pedestal stability and ELM behavior.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

A novel formulation of the unintegrated gluon distribution for DIS

We provide a semi-classical description of the inclusive gluon mediated Deep Inelastic Scattering cross section in a way that accounts for the leading powers in both the Regge and Bjorken limits. Our approach thus allows a systematic matching of small and moderate xBj regimes of gluon proton structure functions. We find a new unintegrated gluon distribution with an explicit dependence on the longitudinal momentum fraction x which entirely spans both the dipole operator and the gluonic Parton Distribution Function. Computing this gauge invariant gluon operator on the lattice could allow to probe the energy dependence of the saturation scale from first principles.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Axion induced SUSY breaking and focus point gaugino mediation

We consider a scenario where supersymmetry breaking, its mediation, and the cancellation of the theta parameter of SU(3) C are all caused by a single chiral multiplet. The string axion multiplet is a natural candidate of such a superfield. We show that the scenario provides a convincing basis of focus point gaugino mediation, where the electroweak scale is explained with a moderate tuning among the parameters of the theory.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Evidence for WW/WZ vector boson scattering in the decay channel ℓνqq produced in association with two jets in proton-proton collisions at s = 13 TeV

Evidence is reported for electroweak (EW) vector boson scattering in the decay channel $\ell\nu$qq of two weak vector bosons WV (V = W or Z), produced in association with two parton jets. The search uses a data set of proton-proton collisions at 13 TeV collected with the CMS detector during 2016-2018 with an integrated luminosity of 138 fb$^{-1}$. Events are selected requiring one lepton (electron or muon), moderate missing transverse momentum, two jets with a large pseudorapidity separation and a large dijet invariant mass, and a signature consistent with the hadronic decay of a W/Z boson. The cross section is computed in a fiducial phase space defined at parton level requiring all parton transverse momenta $p_\mathrm{T}$$\gt$ 10 GeV and at least one pair of outgoing partons with invariant mass $m_\mathrm{qq}$$\gt$ 100 GeV. The measured and expected EW WV production cross sections are 1.90 $^{+0.53}_{-0.46}$ pb and 2.23 $^{+0.08}_{-0.11}$ (scale) $\pm$ 0.05 (PDF) pb, respectively, where PDF is the parton distribution function. The observed EW signal strength is $m_\mathrm{EW}$ = 0.85 $\pm$ 0.12 (stat) $^{+0.19}_{-0.17}$ (syst), corresponding to a signal significance of 4.4 standard deviations with 5.1 expected, and it is measured keeping the quantum chromodynamics (QCD) associated diboson production fixed to the standard model prediction. This is the first evidence of vector boson scattering in the $\ell\nu$qq decay channel at LHC. The simultaneous measurement of the EW and QCD associated diboson production agrees with the standard model prediction.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Electroweak nuclear radii constrain the isospin breaking correction to V ud

We lay out a novel formalism to connect the isospin-symmetry breaking correction to the rates of superallowed nuclear beta decays, δ C , to the isospin-breaking sensitive combinations of electroweak nuclear radii that can be accessed experimentally. We individuate transitions in the superallowed decay chart where a measurement of the neutron skin of a stable daughter even at a moderate precision could already help discriminating between models used to compute δ C . We review the existing experimental situation and make connection to the existing and future experimental programs.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Bisoxazoline-pincer ligated cobalt-catalyzed hydrogenation of alkenes

The efficient and atom economical hydrogenation of alkenes using a novel bisoxazoline ligated cobalt complex has been developed here. The hydrogenation of a variety of alkenes containing electron neutral and electron-donating groups proceeds in high yield, while electron-withdrawing and sterically hindered groups are not tolerated. Heterocycles and internal alkenes were further hydrogenated in moderate to high yields. While the catalyst is enantiopure, no enantioinduction was observed suggesting that other factors are involved in achieving enantiocontrol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Synthesis and characterization of the actinide tosylimido complexes [K(18-crown-6)][An(NSO 2 -$p$-tolyl)(NR 2 ) 3 ] (An = U, Th; R = SiMe 3 )

Reaction of 1 equiv of KN(H)Ts (Ts = p-MeC 6 H 4 SO 2 ) with the actinide metallacycles, [An IV (CH 2 SiMe 2 NSiMe 3 )(NR 2 ) 2 ] (An = U, Th; R = SiMe 3 ), in the presence of 18-crown-6, affords the imido complexes, [K(18-crown-6)][An IV (NTs)(NR 2 ) 3 ] (An = U, 1; Th, 2), in modest to moderate yields after work-up. Both complexes were characterized by X-ray crystallography and 1 H and 13 C{ 1 H} NMR spectroscopies. To our knowledge, they represent the first sulfonylimido complexes reported for the f elements. Finally, they are also a rare example of an isostructural set of actinide imido complexes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Extended use of face masks during the COVID-19 pandemic - Thermal conditioning and spray-on surface disinfection

The current COVID-19 pandemic has resulted in globally constrained supplies for face masks and personal protective equipment (PPE). Production capacity is limited in many countries and the future course of the pandemic will likely continue with shortages for high quality masks and PPE in the foreseeable future. Therefore, expectations are that mask reuse, extended wear and similar approaches will enhance the availability of personal protective measures. Repeated thermal disinfection could be an important option and likely easier implemented in some situations, at least on the small scale, than UV illumination, irradiation or hydrogen peroxide vapor exposure. In this paper, an overview on thermal responses and ongoing filtration performance of multiple face mask types is provided. Most masks have adequate material properties to survive a few cycles (i.e. 30 min disinfection steps) of thermal exposure in the 75°C regime. Some are more easily affected, as seen by the fusing of plastic liner or warping, given that preferred conditioning temperatures are near the softening point for some of the plastics and fibers used in these masks. Hence adequate temperature control is equally important. As guidance, disinfectants sprayed via dilute solutions maintain a surface presence over extended time at 25 and 37°C. Some spray-on alcohol-based solutions containing disinfectants were gently applied to the top surface of masks. Neither moderate thermal aging (less than 24 h at 80 and 95°C) nor gentle application of surface disinfectant sprays resulted in measurable loss of mask filter performance. Subject to bio-medical concurrence (additional checks for virus kill efficiency) and the use of low risk non-toxic disinfectants, such strategies, either individually or combined, by offering additional anti-viral properties or short term refreshing, may complement reuse options of professional masks or the now ubiquitous custom-made face masks with their often unknown filtration effectiveness.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Accelerated oxidation of epoxy thermosets with increased O 2 pressure

Polymer oxidation is usually accelerated with temperature, which is therefore applied in nearly every experimental approach dealing with predictive materials aging. Because of this simple approach, we may tend to neglect that the effective concentration of oxygen also acts as a rate multiplier for oxidation. Increasing the oxygen partial pressure in an aging environment accelerates oxidation, and while there is often a near proportional increase initially, the effect of additional oxygen usually transitions to a saturation level at some elevated pressure. This has been theoretically described in the general autoxidation scheme and is well recognized. However, for many materials the exact rate behavior under moderately increased oxygen concentration remains to be established. We therefore review epoxy oxidation and offer a broader overview of its behavior under increased O 2 partial pressure. Experimental data are given for a few thermoset materials demonstrating their rate behavior under O 2 partial pressure up to 4 atm, meaning approximately 20 times more than under standard atmospheric conditions. Confirmative evidence suggests that epoxy materials will reach saturation oxidation rates only at significantly higher O 2 partial pressure. In such a high-pressure regime it is theoretically possible to not only accelerate oxidation, but to transition into a condition where O 2 diffusion can be increased without further accelerating the oxidation rate. Finally, this can reduce diffusion limited oxidation effects under specific accelerated aging conditions as a combination of temperature and O 2 partial pressure.

36 MATERIALS SCIENCE↗
DOE OSTI2024

N 2 O deconstruction of polycyclooctene to generate carbonyl-functionalized macromonomers

Deconstruction of polyolefins into functionalized macromonomers presents a compelling strategy for polyolefin upcycling by creating macromonomers through dehydrogenation/depolymerization. We show that nitrous oxide (N 2 O), a greenhouse gas waste product from the production of nylon, mediates the deconstruction of polycyclooctene (PCOE) and generates carbonyl-functionalized macromonomers. Carbonyl incorporation and macromonomer molar mass were well controlled by reaction time, and subsequent hydrogenation readily removed residual carbon-carbon double bonds. Here, we also demonstrated that the reaction could progress efficiently with substrates of moderate levels of unsaturation, closely mimicking partially dehydrogenated polyethylene. Such carbonyl-functionalized macromonomers could serve as feedstock for preparing vitrimers and other functional polymers.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Isomerization kinetics of azobenzene crosslinked to a liquid crystal polymer network

Azobenzene is an important chromophore having numerous applications that are a direct implication of its ability to change shape upon irradiation with a suitable wavelength. Here, in this study, photoisomerization kinetics of a diacrylate azobenzene molecule (A3MA) cross-linked to a liquid crystal polymer network (LCN) is investigated. Isomerization experiments were conducted on planar LCN thin films with varying cross-linking densities for a fixed azobenzene concentration. The experiments were conducted at approximately 26 °C, which is significantly below each film’s glass transition temperature. The forward trans-cis and reverse cis-trans isomerization slows down in crosslinked azobenzene liquid crystal polymer networks (ALCNs) as compared to a solution and an uncrosslinked polymer mixture. The observed slowdown is due to the reduction in the free volume and increased steric hindrances with an increase in crosslinking. A single-term first-order kinetics rate equation is known to describe the isomerization kinetics in solutions or uncrosslinked mixtures while the same form fails to represent the reaction kinetics in moderate to highly cross-linked ALCNs. Our results for the first time indicate that a two-term first-order reaction rate is an accurate way to describe the forward trans-cis and reverse thermal cis-trans isomerization in crosslinked azobenzene liquid crystal polymer networks. In addition, the effect of film thickness and incident intensities on the reaction kinetics is investigated. Finally, the two-term isomerization kinetics is incorporated into a finite element photo-chemo-mechanical model to reveal the consequent slowdown in the actuation response of ALCN films. The current findings will be of particular interest to theoreticians and experimentalists alike, for it will help predict and understand accurately the responses of azobenzene-based coatings, and actuators and may have potential applications in underwater soft robotics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Identification of combustion mode under MILD conditions using Chemical Explosive Mode Analysis

Direct Numerical Simulations (DNS) data of Moderate or Intense Low-oxygen Dilution (MILD) combustion are analysed in this paper to identify the contributions of the autoignition and flame modes. This is performed using an extended Chemical Explosive Mode Analysis (CEMA) which accounts for diffusion effects allowing it to discriminate between deflagration and autoignition. This analysis indicates that in premixed MILD combustion conditions, the main combustion mode is ignition for all dilution and turbulence levels and for the two reactant temperature conditions considered. In non-premixed conditions, the preponderance of the ignition mode was observed to depend on the axial location and mixture fraction stratification. With a large mixture fraction lengthscale, ignition is more preponderant in the early part of the domain while the deflagrative mode increases further downstream. On the other hand, when the mixture fraction lengthscale is small, sequential autoignition is observed. Finally, the various combustion modes are observed to correlate strongly with mixture fraction where lean mixtures are more likely to autoignite while stoichiometric and rich mixtures are more likely to react as deflagrative structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Validating simulated mountain wave impacts on hub-height wind speed using SoDAR observations

The ascent of stably stratified air over a mountain barrier can trigger the generation of mountain waves. Mountain waves occur frequently over the Columbia River Gorge in western North America and can impact wind power generation over the area. Therefore, predicting the details of mountain waves events (e.g., dominant wavelength, timing, and duration) can be very valuable for the wind energy community. In this study, the ability of the Weather Research and Forecasting (WRF) model to simulate mountain waves and their impact on hub-height wind speed is investigated. Our results suggest that the WRF model has moderate skill in simulating observed mountain wave. Further, given WRF predictions of wavelength range and wave period, the Fast Fourier Transform can calculate the simulated mountain wave impact on hub-height wind speed. The resulting wind speeds agree well with SoDAR observations in terms of both magnitude and pattern. Finally, for the simulated cases, WRF consistently predicts impacts of significant mountain wave events about an hour earlier than the actual observations. Overall, in this work, the sensitivities as well as uncertainties associated with our methodology are discussed in detail.

17 WIND ENERGY↗
DOE OSTI2022

Machine learning and shallow groundwater chemistry to identify geothermal prospects in the Great Basin, USA

This study discovers various geothermal prospects in the Great Basin, USA based on shallow groundwater chemical (geochemical) data. The geochemical data are expected to include hidden (latent) information that is a proxy for geothermal prospectivity. We processed the sparse geochemical data in the Great Basin at 14,341 locations including 18 attributes. Next, a non-negative matrix factorization with customized k-means clustering is applied to the geochemical data matrix that automatically finds three hidden geothermal signatures representing modestly, moderately, and highly confident geothermal prospects. The algorithm also evaluated the probability of occurrence of these types of resources through the studied region. There is a consistency between regional geothermal prospectivity as estimated by our ML methodology and the traditional play fairway analysis conducted over a portion of the study area. We also identify the dominant data attributes associated with each signature. Finally, our ML analyses allow us to reconstruct attributes from sparse into continuous over the study domain. The predicted continuous attributes can be used for future detailed geothermal explorations in the Great Basin.

15 GEOTHERMAL ENERGY↗
DOE OSTI2026

Circular economy pathways for decarbonizing aluminum and steel automotive body sheet components in the United States

Decarbonizing vehicle production is essential to reducing automotive sector emissions. This study quantifies greenhouse gas (GHG) emissions from aluminum and steel auto-body sheet components produced in the US. It evaluates the effectiveness of circular economy (CE) strategies (greater closed-loop recycling of pre-consumer scrap, post-consumer scrap, and increased manufacturing yields) to reduce supply chain emissions across different process technology and electricity grid decarbonization pathways. We combine dynamic material flow analysis (2025–2050) with cradle-to-gate life-cycle modeling to assess production emissions and the potential reductions associated with the CE strategies under frozen, moderate, and aggressive technology and grid decarbonization scenarios. Current emissions intensities are estimated at approximately 12.3 kg.CO₂eq/kg of aluminum and 4.3 kg.CO₂eq/kg of steel sheet embedded in the vehicle. Under the frozen decarbonization scenario and current levels of circularity, annual emissions attributable to US aluminum and steel auto-body sheet supply chains could rise by 54 % and 18 % respectively by 2050. Rapid deployment of the CE strategies can cut these annual emissions in 2050 by 52 % for aluminum and 44 % for steel. However, scrap quality constraints lead to saturation points, limiting these benefits unless addressed. Aggressive deployment of low-carbon production technologies and a low-carbon grid reduces the relative benefit of implementing the CE strategies; however, even under the aggressive technology and grid decarbonization scenario, the CE strategies reduce annual emissions by a further 23 %-54 % by 2050. These findings highlight the urgent need to integrate CE strategies into the sheet metal supply chain to support decarbonization efforts and help meet climate targets.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

A radiative transfer model for solar induced fluorescence using spectral invariants theory

Solar Induced chlorophyll Fluorescence (SIF) shows promise as an approach for estimating gross primary production (GPP) remotely. However, sun-target-sensor geometry and within-canopy absorption of SIF can alter the relationship between measured SIF and GPP, because sensors can only retrieve some unknown fraction of the total emitted SIF. Radiative transfer models that allow for variation in canopy structure and sensor angles are therefore needed to properly interpret SIF measurements. Spectral invariants allow decoupling of the wavelength-independent canopy structure and the wavelength-dependent leaf and soil spectrum in the radiative transfer process. Here we develop a simple analytical Fluorescence Radiative Transfer model based on Escape and Recollision probability (FluorRTER) to investigate the impact of canopy structure and sun-target-sensor geometry on SIF emissions. SIF simulations using the FluorRTER model agreed well the one-dimensional Soil-Canopy Observation of Photochemistry and Energy balance (SCOPE) model and the three-dimensional Fluorescence model with Weighted Photon Spread (FluorWPS) model. The fractional vegetation cover (FVC) and clumping effect have a large influence the SIF emission of 3D discontinuous canopies. For a moderate solar zenith angle (30°) and a clumped canopy (FVC?=?0.6), the difference between the directional observed SIF of a 3D discontinuous canopy and a 1D homogeneous canopy was as large as 43.2% and 38.4% for Photosystem I?+?II fluorescence at 685?nm and at 740?nm, respectively. By bridging the gap between observed SIF and total emitted SIF over 3D heterogeneous vegetation canopies, the FluorRTER model can assist with the angular normalization of SIF measurements and enable the more robust interpretation of how variations in SIF from directional and hemispherical in-situ, airborne and satellite observations relate to leaf and whole-canopy physiological processes.

Zeng, Yelu↗