Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “joining”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Mechanical Properties and Corrosion Behavior of AA5754-AA6061 Dissimilar Aluminum Alloys Welded by Cold Metal Transfer

The trend of using lightweight materials in the automotive industry brings along the necessity of dissimilar welding of aluminum alloys such as AA5754 and AA6061. Hybrid structures in automobiles are subjected not only to mechanical forces but also corrosive effects of the environment. In this study, cold metal transfer welding, which is suitable for welding thin sheets and dissimilar materials, was applied to join AA5754 to AA6061. It was aimed to investigate the effect of weld heat input on mechanical properties and corrosion rate measured by the Tafel extrapolation method in 3.5 wt.% NaCl solution at room temperature. The tensile strength of AA5754-AA6061 joints tended to reduce with increasing heat input. Corrosion test results showed that the increased heat input decreased the corrosion resistance and caused intergranular corrosion besides pitting corrosion.

36 MATERIALS SCIENCE↗

Butt Laser Welding–Brazing of AZ31 Mg to Nickel-Coated Ti-6Al-4V

Mg and Ti alloy are hard to be bonded due to their huge discrepancy in physical and metallurgical characteristics. As an intermediate element, Ni is feasible for joining of Mg and Ti. The interfacial microstructure and mechanical properties of laser-welded–brazed AZ31 Mg/Ti-6Al-4V joints in butt configuration were investigated with different thicknesses of electrodeposited Ni interlayer. The interfacial reaction products evolved from an ultra-thin Ti{sub 3}Al layer to Ti{sub 2}Ni layer mingled with Ti{sub 3}Al, and more Mg{sub 3}AlNi{sub 2} compounds were produced in the fusion zone (FZ) as Ni coating thickness increased. Slag inclusions and cracks were observed in interfacial layer when coating thickness exceeded 2.5 μm. The quantity of Mg{sub 3}AlNi{sub 2} and the thickness of interfacial layer decreased from the top to bottom of groove of the same joint owing to high thermal gradient during laser welding. The chemical potential of Al and Ni indicated that Al-Ti reaction product was produced more easily than Ni-Ti in 0.001Mg-(Ni-Al-Ti) system. The thermodynamic calculation results of Gibbs free energy suggested the preferential formation Ti-Al phase and Ti-Ni phase along the interface while the Mg-Al-Ni ternary phase in the FZ. Fracture loads of joints increased first followed by a decline with the increase in coating thickness. The joint fractured at the Mg base metal, reaching a maximum value of 3900 N with the Ni coating thickness of 1.5 μm. In the case of using thinner or thicker Ni coating, crack propagated along the interface due to the insufficient metallurgical bonding or defects existed in the interfacial layer. The characteristic of fracture surface changed from the tear ridges and terraces to river pattern when interfacial failure occurred.

36 MATERIALS SCIENCE↗

Characterization of Laser-Welded Ti Alloy and Stainless Steel Joint Using Cu Interlayer

In this study, Cu was used as an interlayer to restrain the formation of brittle Ti-Fe intermetallics when joining Ti alloy to SS. Microstructures of the joint were analyzed using optical microscopy, scanning electron microscopy and x-ray diffraction. Besides, the tensile strength of the joint was also measured. The melting amount of base materials was controlled by changing thickness of Cu interlayer to control the melting proportion in weld. The melting amount of base materials in weld decreased with the thickness of Cu interlayer. The content of Cu solid solution in weld increased with the thickness of Cu interlayer. Ti-Cu compound layer was formed on the Ti alloy side. The width of the Ti-Cu compound layer increased with the increase in heat input. The tensile strength of joint was largely impacted by Ti-Cu compound layer. The tensile strength of joint first increased and then decreased with the increase in width of the Ti-Cu compound layer.

36 MATERIALS SCIENCE↗

Flow Patterns, Microstructure and Mechanical Properties of AZ31/Al6061 Dissimilar Friction Stir-Welded Joints

Dissimilar joints between die-cast AZ31 and extruded Al6061-T6 were joined using friction stir welding technology at a constant transverse speed (50 mm/min) and rotation rate of 800 or 1000 rpm. The flow patterns, microstructure evolution and intermetallic compounds in dissimilar joints were studied by optical and scanning electron microscopy. The relationship between microstructure and tensile properties was analyzed. The microhardness distribution along the horizontal centerline in cross section was investigated. Local flow without obvious mixing existed between Mg and Al metals in the tool shoulder-affected zone. For the tool-pin-affected zone, two typical zones, namely, the “extrusion zone” and “flow zone” existed because of the different flow modes of the plastic metals. The phase analysis showed that intermetallic compounds, including Al{sub 12}Mg{sub 17} and Al{sub 3}Mg{sub 2} formed in banded structures. Phase analysis showed that a joint with welding parameters of 800 rpm and 50 mm/min (Joint-500) had good mechanical properties because of the more uniform microstructure distribution and fewer intermetallic compounds. Fracture analysis indicated some microvoids and lamellate intermetallic compounds in the fracture surface of the joint with welding parameters of 1000 rpm and 50 mm/min (Joint-1000), which deteriorated its tensile strength significantly.

36 MATERIALS SCIENCE↗

Refill Friction Stir Spot Welding Dissimilar Al/Mg Alloys

Dissimilar Al/Mg alloys were joined by refill friction stir spot welding (RFSSW) in this work. The effect of sleeve plunge depth on microstructure and mechanical properties of the joints was studied. The results showed that sound joint can be obtained at sleeve plunge depth of 2.4 mm. Intermetallic compounds (IMCs) layer, formed by the liquid eutectic phase, were observed at both the sleeve-affected zone and joint center. The IMC at the pin-affected zone was thicker than that at the sleeve-affected zone because of its flow characteristic. Less liquid eutectic phase formed during RFSSW when joint using Mg as the upper sheet because the oxide layer on the Al sheet was hard to break, resulting to thinner IMC layer. The maximum load of 3.6 kN was obtained at 2.6 mm when the Al alloys served as the upper sheet, and the maximum failure of 3.6 kN was also obtained at 2.4 mm when the Mg alloys served as the upper sheet. The RFSSW joint presented shear fracture mode. The XRD patterns showed that the IMC of Al{sub 3}Mg{sub 2} and Al{sub 12}Mg{sub 17} formed inside the joint.

36 MATERIALS SCIENCE↗

Laser Weldability of AlSi{sub 10}Mg Alloy Produced by Selective Laser Melting: Microstructure and Mechanical Behavior

Selective laser melting (SLM) allows 3D complex parts to be produced with integrated functionalities but does not permit to realize large dimension parts, as the building chamber volume of commercial SLM systems is limited. Therefore, the possibility of joining SLM-built parts by welding appears as extremely valuable. In this work, laser weldability of SLMed AlSi{sub 10}Mg parts has been investigated. The cooling rates induced by the welding process are lower than the ones of SLM; therefore, typical eutectic silicon network of SLM-built parts appears broken in both the melted zone and part of the heat-affected zone, as confirmed by calorimetric measurement. This microstructural evolution caused a local decrease of hardness from 132 HV to 73 HV and a reduction of ductility caused by porosity formation in the weld bead. Moreover, the thermal treatment, performed at 320°C, can limit the gap of tensile response among welded bead and base SLM material.

36 MATERIALS SCIENCE↗

A Combined Experimental and Modeling Approach to Investigate the Performance of Joint Between AZ31 Magnesium and Uncoated DP590 Steel Using Friction Stir-Assisted Scribe Technique

In this study, friction stir assisted scribe technique is used to achieve a viable joint between AZ31 magnesium alloy and uncoated DP590 steel. Here, the mechanical properties and performance of the joint are investigated using finite element modeling and electron microscopy. The joint strength can be ascribed to two factors, the mechanical interlocking and the metallurgical bonding of two materials at their interface. The contribution of both factors is intended, and the metallurgical bonding is studied to understand the basic joining phenomenon.

36 MATERIALS SCIENCE↗

Neutron Diffraction Residual Stress Study of a AA2219-T87 Self-Reacting Friction Stir Weld

2219-T87 is a precipitation hardenable aluminum-copper alloy which sees wide use in structural aerospace components. Thick panels of this alloy are joined via self-reacting friction welding (SRFSW); however, this thermomechanical process can result in significant loss of the alloy’s strengthening precipitates and large residual stresses which are detrimental to mechanical behavior and performance. High-resolution maps of the residual strain and stress states along the normal, transverse, and longitudinal directions of 2219-T87 SRFSW were obtained using neutron diffraction measurements. Residual stress had the highest tensile value in the heat-affected zone (HAZ) and the largest compressive stress in the base metal region of the normal and transverse directions. Line profile residual stress distributions displayed an “M”-shaped distribution in each direction with the longitudinal direction being the most pronounced while 2D residual stresses displayed an hourglass-shaped pattern. Further, average maximal longitudinal residual stress values ranged from 60.6 to 85.6% of yield. Microhardness testing across the transverse weld section produced a “V”-shaped curve with slight hardness recovery in the stir zone. Maximal and minimal microhardness values were observed in the base metal (154 HV) and thermomechanically affected zone (82 HV), respectively. Microstructural evolution was recorded using optical microscopy and showed decreasing grain size from the HAZ to the stir zone.

36 MATERIALS SCIENCE↗

Multiscale Modeling Meets Machine Learning: What Can We Learn?

Machine learning is increasingly recognized as a promising technology in the biological, biomedical, and behavioral sciences. There can be no argument that this technique is incredibly successful in image recognition with immediate applications in diagnostics including electrophysiology, radiology, or pathology, where we have access to massive amounts of annotated data. However, machine learning often performs poorly in prognosis, especially when dealing with sparse data. This is a field where classical physics-based simulation seems to remain irreplaceable. In this review, we identify areas in the biomedical sciences where machine learning and multiscale modeling can mutually benefit from one another: Machine learning can integrate physics-based knowledge in the form of governing equations, boundary conditions, or constraints to manage ill-posted problems and robustly handle sparse and noisy data; multiscale modeling can integrate machine learn- ing to create surrogate models, identify system dynamics and parameters, analyze sensitivities, and quantify uncertainty to bridge the scales and understand the emergence of function. With a view towards applications in the life sciences, we discuss the state of the art of combining machine learning and multiscale modeling, identify applications and opportunities, raise open questions, and address potential challenges and limitations. We anticipate that it will stimulate discussion within the community of computational mechanics and reach out to other disciplines including mathematics, statistics, computer science, artificial intelligence, biomedicine, systems biology, and precision medicine to join forces towards creating robust and efficient models for biological systems.

machine learning, multiscale modeling, physics-bas↗

Temperature and Material Flow Prediction in Friction-Stir Spot Welding of Advanced High-Strength Steel

Friction-stir spot welding (FSSW) has been shown to be capable of joining advanced high-strength steel, with its flexibility in controlling the heat of welding and the resulting microstructure of the joint. This makes FSSW a potential alternative to resistance spot welding if tool life is sufficiently high, and if machine spindle loads are sufficiently low that the process can be implemented on an industrial robot. Robots for spot welding can typically sustain vertical loads of about 8 kN, but FSSW at tool speeds of less than 3000 rpm cause loads that are too high, in the range of 11–14 kN. Therefore, in the current work, tool speeds of 5000 rpm were employed to generate heat more quickly and to reduce welding loads to acceptable levels. Si3N4 tools were used for the welding experiments on 1.2-mm DP 980 steel. The FSSW process was modeled with a finite element approach using the Forge* software. An updated Lagrangian scheme with explicit time integration was employed to predict the flow of the sheet material, subjected to boundary conditions of a rotating tool and a fixed backing plate. Material flow was calculated from a velocity field that is two-dimensional, but heat generated by friction was computed by a novel approach, where the rotational velocity component imparted to the sheet by the tool surface was included in the thermal boundary conditions. An isotropic, viscoplastic Norton-Hoff law was used to compute the material flow stress as a function of strain, strain rate, and temperature. The model predicted welding temperatures to within percent, and the position of the joint interface to within 10 percent, of the experimental results.

Miles, Michael↗

High-Speed Friction-Stir Welding To Enable Aluminum Tailor-Welded Blanks

Current joining technologies for automotive aluminum alloys are utilized in low-volume and niche applications, and have yet to be scaled for the high-volume vehicle market. This study targeted further weight reduction, part reduction, and cost savings by enabling tailor-welded blank technology for aluminum alloys at high-volumes. While friction stir welding has been traditionally applied at linear velocities less than one meter per minute, high volume production applications demand the process be extended to higher velocities more amenable to cost sensitive production environments. Unfortunately, weld parameters and performance developed and characterized at low to moderate welding velocities do not directly translate to high speed linear friction stir welding. Therefore, in order to facilitate production of high volume aluminum welded components, parameters were developed with a minimum welding velocity of three meters per minute. With an emphasis on weld quality, welded blanks were evaluated for post-weld formability utilizing a combination of numerical and experimental methods. Evaluation across scales was ultimately validated by stamping full-size production door inner panels made from dissimilar thickness aluminum tailor-welded blanks, which provided validation of the numerical and experimental analysis of laboratory scale tests.

aluminum↗

Five-axis ultrasonic additive manufacturing for nuclear component manufacture

Ultrasonic additive manufacturing (UAM) is a three-dimensional metal printing technology which uses high-frequency vibrations to scrub and weld together both similar and dissimilar metal foils. There is no melting in the process and no special atmosphere requirements are needed. Consequently, dissimilar metals can be joined with little to no intermetallic compound formation, and large components can be manufactured. These attributes have the potential to transform manufacturing of nuclear reactor core components such as control elements for the High Flux Isotope Reactor at Oak Ridge National Laboratory. These components are hybrid structures consisting of an outer cladding layer in contact with the coolant with neutron-absorbing materials inside, such as neutron poisons for reactor control purposes. UAM systems are built into a computer numerical control (CNC) framework to utilize intermittent subtractive processes. These subtractive processes are used to introduce internal features as the component is being built and for net shaping. The CNC framework is also used for controlling the motion of the welding operation. Lastly, it is demonstrated here that curved components with embedded features can be produced using a five-axis code for the welder for the first time.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Investigation of Raster Pattern Spacing and Direction for Friction Stir Additive Manufacturing of Al-5083

Friction stir additive manufacturing (FSAM) is a sheet-lamination based additive manufacturing technique. In addition to the traditional factors that govern the friction stir process-structure-property relationship, the processing history is convoluted by the in-plane raster pattern and repeated thermal cycling from subsequent layers. This can lead to complex thermal gradients within the workpiece and reprocessing of material. Here, this work aims to understand the impact of raster pattern spacing and direction on the microstructure and properties during friction stir additive manufacturing of Al-5083. Control of the raster spacing can lead to an increase in hardness of up to 18% from the base material and defect-free joining. These results are then directly demonstrated at the component-scale for FSAM of Al-5083.

36 MATERIALS SCIENCE↗

Effects of an External Magnetic Field on Keyhole Mode Laser Melting of 316 Stainless Steel

Keyhole-mode laser melting is an efficient method for joining or cutting large, thick components, but controlling keyhole depth and fluctuations has remained challenging. Applying an external magnetic field can control melt pool flows and indirectly influence keyhole morphology and dynamics. The induced Lorentz force, comprising Seebeck and damping components, plays a crucial role in the melt pool dynamics, depending on temperature gradient, flow rates, and magnetic field orientation and magnitude. This research investigates the effects of an external magnetic field on keyhole behavior during laser spot melting of 316 stainless steel using synchronized high-speed synchrotron X-ray and thermal imaging. Findings revealed that a longitudinal magnetic field (120 mT) increased keyhole depth but exacerbated lateral fluctuations, resulted in a 20% increase in the melt pool temperature gradient and a 27% decrease in cooling rate. Conversely, a transverse magnetic field (760 mT) reduced keyhole depth and improved porosity formation. The findings suggest that a decrease in keyhole depth correlates with a decrease in fluctuations, and vice versa. These insights enhance understanding of external magnetic fields’ impact on laser melting, with implications for improving part quality.

Alamdari, Aslan Bafahm [The Ohio State Univ., Colu↗

Can synthetic lethality approach be used with DNA repair genes for primary and secondary MDS?

Cancer-specific defects in DNA repair pathways create the opportunity to employ synthetic lethality approach. Recently, GEMA (gene expression and mutation analysis) approach detected insufficient expression of BRCA or NHEJ (non-homologous end joining) to predict PARP inhibitors response. We evaluated a possible role of DNA repair pathways using gene expression of single-strand break (XPA, XPC, XPG/ERCC5, CSA/ERCC8, and CSB/ERCC6) and double-strand break (ATM, BRCA1, BRCA2, RAD51, XRCC5, XRCC6, LIG4) in 92 patients with myelodysplastic syndrome (73 de novo, 9 therapy-related (t-MDS). Therapy-related MDS (t-MDS) demonstrated a significant downregulation of axis BRCA1-BRCA2-RAD51 comparing to normal controls (p = 0.048, p = 0.001, p = 0.001). XRCC6 showed significantly low expression in de novo MDS comparing to controls (p = 0.039) and for patients who presented chromosomal abnormalities (p = 0.047). Downregulation of LIG4 was consistently associated with poor prognostic markers in de novo MDS (hemoglobin < 8 g/dL (p = 0.040), neutrophils < 800/mm{sup 3} (p < 0.001), patients with excess of blasts (p = 0.001), very high (p = 0.002)/high IPSS-R (p = 0.043) and AML transformation (p < 0.001). We also performed an evaluation of GEPIA Database in 30 cancer types and detected a typical pattern of downregulation as here presented in primary or secondary MDS. All these results suggest synthetic lethality approach can be tested with DNA repair genes (beyond that of BRCA1/2 status) for de novo and therapy-related myelodysplastic syndrome and may encourage clinical trials evaluating the use of PARP1 inhibitors in MDS. Graphic Abstract: .

62 RADIOLOGY AND NUCLEAR MEDICINE↗

3D printing of metal-based materials for renewable energy applications

Large-scale renewable energy must overcome conversion and storage challenges before it can replace fossil fuels due to its intermittent nature. However, current sustainable energy devices still suffer from high cost, low efficiency, and poor service life problems. Recently, porous metal-based materials have been widely used as desirable cross-functional platforms for electrochemical and photochemical energy systems for their unique electrical conductivity, catalytic activity, and chemical stability. To tailor the porosity length scale, ordering, and compositions, 3D printing has been applied as a disruptive manufacturing revolution to create complex architected components by directly joining sequential layers into designed structures. In conclusion, this article intends to summarize cutting-edge advances of metal-based materials for renewable energy devices (e.g., fuel cells, solar cells, supercapacitors, and batteries) over the past decade.

36 MATERIALS SCIENCE↗

Data Mining and Visualization of High-Dimensional ICME Data for Additive Manufacturing

Integrated computational materials engineering (ICME) methods combining CALPHAD with process-based simulations can produce rich, high-dimensional data for alloy and process design. In ICME methods for metallurgical applications, the visualization and interpretation of such high-dimensional data has previously been through heat maps represented in 2 or 3 dimensions. While such an approach is ideal when one variable is varied at a time, in the case of high-dimensional data with multiple variables varied simultaneously, as is the case in additive manufacturing, interpreting the trends through two- or three-dimensional heat maps becomes challenging. Here, we propose a strategy of mixed visual data mining and quantitative analysis for high-dimensional metallurgical and process data using high-throughput thermodynamic calculations. Two case studies show the application of the proposed approach. The first case study investigated the effects of feedstock chemistry on the δ ferrite formation in 316L stainless steel powders used for binder jet additive manufacturing. The second case study linked Scheil–Gulliver calculations to a process model for dissimilar joining of aluminum alloys 5356 and 6111 during laser hot-wire additive manufacturing. Both cases contained thousands of calculated data points, showcasing the utility of visual data analysis through parallel coordinate plotting, Pearson correlation coefficient matrices, and scatter matrices compared to traditional process maps. These visualization techniques can be extended to many additive manufacturing problems to capture process–structure–property relationships for additively manufactured components.

36 MATERIALS SCIENCE↗

Molecular Dynamics Simulation of Hygroscopic Aging Effects in Epoxy Polymer

The automobile industry is incorporating more lightweight content in car designs to boost fuel-economy. New structural adhesives are needed to mitigate the corrosion and thermal expansion issues associated with joining dissimilar lightweight materials, but adhesive developers lack a fundamental understanding of the chemistry that occurs in the adhesive as the joint ages. In this study, we developed structural adhesive molecular models and applied classical molecular dynamics simulations and density functional theory calculations to gain molecular insights into the influence of water molecules on the properties of epoxy-based adhesives (DGEBA + Jeffamine (JD230)). The simulations were complemented by experimental synthesis and characterization. Our work underscores the impact of water molecules on the local structure of the epoxy network as well as resulting mechanical properties. Water molecules were mainly coordinated with hydroxyls, primary amines and secondary amines, but also weakly coordinated with ether linkages, which were found most probable to be labile. Simulated stress–strain data indicates that increasing the water content deteriorates the mechanical properties. The Young’s modulus decreased by ~ 30% when the water content increased to 3 wt%. We conclude, this integration of molecular-level chemical insights with mechanical property simulations of the hydrated epoxy system and experimental validation holds the promise to advance lightweight joint technologies.

36 MATERIALS SCIENCE↗