Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “goals”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Synthetic Pathways to gamma-Graphyne and Related Allotropes of Carbon

Graphynes, two-dimensional carbon lattices combining sp 1 and sp 2 hybridized atoms, were predicted theoretically more than three decades ago, but few structures have been realized to date. These carbons are believed to possess remarkable mechanical and electronic properties, including high charge carrier mobilities comparable to those in graphene (10 4 to 10 5 cm 2 V -1 s -1 ). Unlike graphene, certain graphynes are predicted to be intrinsic semiconductors. Among these intriguing structures, γ-graphyne stands out as the structurally simplest and most symmetric sp 1 /sp 2 lattice. γ-Graphyne was first theorized in 1987. In contrast with graphene, γ-graphyne will be a semiconductor with a small band gap suitable for fabrication of electronic devices. This solves one of the fundamental problems of carbon-based electronics, the necessity for inducing a band gap in graphene. γ-Graphyne has the potential to form the basis for the next generation of carbon-based electronics operating at speeds unattainable by traditional silicon chips. Unlike silicon, γ-graphyne is a direct band gap semiconductor, and it will feature exceptional strength comparable to that of other 2D carbon allotropes. Such combination of properties may enable a new generation of highly efficient, ultra-light and flexible solar cells. Despite being a potentially “magical” material, γ-graphyne remained synthetically elusive for over three decades. The primary goals of this project were: (1) Synthesis of bulk γ-graphyne phases through solution-phase 2D polymerizations; (2) Experimental exploration of the physical and chemical properties of γ-graphyne; and (3) Mechanistic and theoretical studies of the novel chemical transformations developed in Goal 1. Common pyrolytic and vapor-deposition methodologies used for the synthesis of graphitic allotropes are unsuitable for graphyne and other sp 1 -contaning structures, as acetylenes readily convert to graphene and amorphous carbon at high temperatures. In contrast, this proposal is based on solution-based 2D polymerization. The major advantages of this approach over the traditional high temperature techniques are the potential to adjust the structure of the material with atomic precision, and the possibility of using structurally complex and relatively fragile repeat units. The outcomes of this research can revolutionize carbon nanotechnology, expanding the field’s structural toolbox beyond primarily graphitic and benzenoid structures. Understanding the chemistry of sp 1 carbon allotropes can lead to entirely new classes of structures with unique properties, including graphyne ribbons, nanotubes, quantum dots, and heterostructures with other 2D materials. Furthermore, the development of reliable and robust synthetic pathways towards periodic covalent molecular sheets with atomically precise structures shall have a profound impact on chemistry and materials science.

2D polymerization↗
DOE OSTI2025

Early Career: First-Principles Tools for Nonadiabatic Attosecond Dynamics in Materials

The overarching goal of this project was to develop computer tools for predicting how electrons move in molecules and solids at the attosecond (billionth-of-a-billionth of a second) time scale, during and after interaction with intense and/or high energy laser light. An associated goal was to also determine how X-ray spectroscopy could be used as a probe of these dynamics. The project resulted in multiple methodology developments that allow for these processes to be simulated from first-principles, most notably the use of small bulk-mimicking clusters to model solids and fixes for a deficiency in a commonly used method (time-dependent density functional theory). Additionally, the simulations showed that X-ray absorption peaks can be directly related to the electron density above the absorbing atom, and can thus be used as an intuitive probe of "where the electrons are" at a given time in the system. Collectively, these tools and results expected to be valuable for predicting and interpreting future attosecond experiments, especially for X-ray pump/probe studies at free-electron laser facilities.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2025

Exploring Nontrivial Topological Superconductivity in 2M-WS2 for Topological Quantum Computation

This project has two main research goals: (1) growing the high-quality two-dimensional (2D) 2M-pahse WS 2 (2M-WS 2 ) single crystals and identifying clear signatures of the unconventional superconductivity in the 2M-WS 2 ; and (2) establishing the layer-dependence of the Majorana zero mode in the 2M-WS 2 down to the monoatomic layer limit. These goals were planned to be achieved by growing high-quality and large-scale 2M-WS 2 single crystals and transferring their thin layers onto different substrates for the proposed measurements. The layer-dependent unconventional superconductivity in 2M-WS 2 were systematically studied by different techniques, including transport measurements (charge, thermal and spin), scanning tunneling microscopy and spectroscopy (STM/S), angle-resolved photoemission spectroscopy (ARPES), and theoretical calculations. The research team is comprised of researchers from University of Wyoming (UW) and three DOE National Laboratories (DOE NLs), including Argonne National Laboratory (ANL), Lawrence Berkeley National Laboratory (LBNL) and Sandia National Laboratories (SNL), with complete and complementary expertise: PI Tian: Handling 2D materials, nanofabrication, nanodevices, and quantum transport; Co-Is: Ackerman and Leonard: van der Waals material crystal growth and handling; Chien: Nanoimaging with STM/S; and Tang: Magnetic measurements and charge and thermal transport; National lab collaborators (NLs): Guisinger (ANL): STM/S and nanoimaging; Mo and Rotenberg (LBNL): ARPES and nano ARPES (nARPES); Lu (SNL): Quantum information science, quantum transport, and nanofabrication; and Baczewski (SNL): Theoretical modeling and calculations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

National Zero-Emission Freight Corridor Strategy

The United States has committed to decarbonizing freight transportation by advancing the deployment of commercial zero-emission medium- and heavy-duty vehicles (ZEMHDVs) and infrastructure. It is pursuing this goal by leveraging historic federal and private investments, policies, and partnerships. Through the U.S. National Blueprint for Transportation Decarbonization1 and the Global Memorandum of Understanding for Zero-Emission Medium- and Heavy-Duty Vehicles,2 the United States has committed to identifying viable pathways and implementation actions that promote at least 30% ZE-MHDV sales by 2030, with a goal of 100% by 2040. These actions, along with the investments laid out in the Bipartisan Infrastructure Law and Inflation Reduction Act, put the nation on a path to advancing transportation and infrastructure solutions that are better for freight movement, our communities, the environment, and the economy. Providing ubiquitous and convenient access to electric vehicle (EV) charging and hydrogen refueling along our nation’s freight corridors, and at truck depots within freight hubs, is key to successfully deploying ZE-MHDVs. Consistent with its charge in the Bipartisan Infrastructure Law, 3 the Joint Office of Energy and Transportation (Joint Office), in collaboration with the U.S. Department of Energy (DOE), Department of Transportation, and the Environmental Protection Agency, has developed the National Zero-Emission Freight Corridor Strategy (Strategy). The Strategy guides infrastructure deployment to meet growing market demands; catalyze public and private investment; and support utility and regulatory planning and action at local, state, and regional levels.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Project Title: Demonstration High Temperature Superconducting NonPlanar Stellarator Magnet with Advanced Manufactured Assemblies

This is the final report for the project “Demonstration High Temperature Superconducting Non- Planar Stellarator Magnet with Advanced Manufactured Assemblies”, funded by DOE, and performed by Type One Energy from September, 2020, to March 2024 involving the Fusion Technology Institute at the University of Wisconsin–Madison, the Plasma Science and Fusion Center (PSFC) at the Massachusetts Institute of Technology (MIT) and Commonwealth Fusion Systems (CFS) to design and fabricate the first non-planar HTS (REBCO) coil for a high-field stellarator based on the SPARC tokamak’s VIPER cable concept. Stellarators at high fields make high-temperature superconducting magnets necessary for a compact fusion device. But the asymmetric and non-planar nature of its components, especially the magnets make it difficult for scalable producibility. To address these challenges, two promising technologies have emerged: advanced manufacturing (AM) for the supporting plates for forming the magnets, and high-temperature superconducting (HTS) cables inside the plates. AM has advanced enough to produce stellarator components with the necessary geometric complexity, size, and the precision, leading to potentially significant reductions in production time, cost, and waste. The cost of HTS tape has decreased dramatically, and progress in HTS planar magnet development has reached a point where it can be proposed for application to complex 3D non-planar magnets. The main objective of this project is to develop, demonstrate and pre-commercialize a novel, non-planar HTS coil shape that remains superconducting to achieve production scalable reductions in time and cost and performance. The proposed technology is based on the novel concept of a precision sub-scale HTS nonplanar coil assembly. This project focuses on the design, fabrication, material optimization of cable design, and validation and demonstration of the high current carrying capability of superconducting magnets and their support in a complex 3D shape needed for application to stellarator magnetic plasma confinement. The specific objectives of this research program include: (1) The successful application of metal AM to build a precision sub-scale HTS nonplanar coil, (2) An HTS cable and cross-section design that can conform to the required nonplanar coil shape (bend radii as tight as 10-cm) and remains superconducting at an engineering current density of 1.35 kA/cm 2 at 77 K and 1 tesla at the conductor (5 kA in the cable). To achieve the above challenging goals, we have formed a multidisciplinary research team consisting of members from Type One Energy and UW-Madison, MIT PSFC and CFS with complementary skills and strong facilities. The team worked collaboratively on fundamental and applied research on the following three major technical areas: (1) Design, fabrication, and optimization of non-planar HTS Cable The ultimate goal of the project is to determine if commercial REBCO tapes and additive manufacturing can be used to fabricate high field (≥ 10T) non-planar coils with tight bending radii (≃ 100mm) and with a degradation of the critical current (Ic) smaller than 20% with respect to the expected performance. We started with shorter length cable to evaluate the scalability of the production process and eventually reached multiple turns for higher magnetic fields. Our findings suggest that a stellarator coil system of a relevant size, characterized by its asymmetric and non-planar components, can be fabricated using a formed cable in plate method. This system can be simulated using a large-scale modeling approach. The use of hybrid modeling 3 techniques will be pivotal in reducing the complexity of the model and in assessing expected performance in designs. (2) Modeling and simulation of the non-planar HTS Cable Multiphysics simulations are performed using the commercial software and are carried out in self-field conditions, involving 2D and 3D models and twisted around one slot of twist-pitched VIPER cable. Multiphysics simulations are mainly focused on the coil for the critical current evaluation, the magnetic field map, self-Lorentz forces and mechanical, and magnetothermal behavior and the quench dynamics. The detailed model and prediction of the superconducting performance of a stellarator-relevant demonstration cable from numerical simulations supports the results from the actual testing backing the results. A detailed description and results are provided in the later sections. (3) Design, fabrication, and optimization of support for the non-planar HTS Cable The team developed an additive manufactured (AM) coil positioning plate that formed into the required non-planar geometry (with bend radii as tight as 10-cm) and to acceptable tolerances required for a stellarator magnet: (+0.25-mm from ideal on dimensions of coil positioning plates and up to +1-mm from ideal for position of wound coil). The plate materials is also included in this selection process from fabrication and 3D printing perspective and commensurate with eventual application to a fusion reactor. From the cost effectiveness point of view, the HTS coil and plate has the potential to cost less than that made in conventional methods with less waste (<75% waste) reducing time (<50%) and cost (<50%), especially as the AM field matures. The application of advanced manufacturing in the construction of the support plates will also lead to cost reduction, as the cables can be easily replaced, thereby making the assembly modular. With such high primary cost and time savings, high current densities and magnetic field, the funded R&D work has validated the designs, proven the feasibility, and characterized the performance of the HTS coil and plate assembly, paving the way for a relevant-size stellarator coil system.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Integration Methods for High-Density Integrated Electric Drives (Final Technical Report)

The project goal was to research, design and fabricate high-power-density, high-performance SiC power electronic modules for motor drive inverters in electric vehicles (EVs) to enable the subsequent motor drive to achieve a power density of 100 kW/l. EVs use electric motors instead of internal combustion engines as the prime mover, and their core components are semiconductor-based power electronic modules. Efficient power electronic modules play a vital role in power conversion systems. The performance of power modules directly affects the energy efficiency and overall performance of electric vehicles. Therefore, it is particularly important to develop power modules with high power density and high electrical performance that will perform reliably under EV environmental conditions. To achieve these goals, advanced electronic packaging technologies are required. This report describes a 5-year effort to integrate key aspects surrounding the basic power devices into the module itself to increase power density. These include sensing and sensing readout circuits, gate driver circuits, and two-sided cooling solutions.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Enabling Low-Temperature (LTP) Ignition Technologies for Multi-Mode Engines through the Development of a Validated High-Fidelity LTP Model for Predicative Simulations Tools

The goal of multi-mode engine architectures is to extend current lean-burn dilution limits with renewable fuels, which requires spark plugs to deposit high energies (hundreds of mJ) in order to initiate ignition and complete combustion. At elevated energy deposition rates, spark plugs experience increased electrode erosion and thermal losses, which ultimately shortens the spark-plug lifetime and lowers ignition efficiency. As such, in order to safeguard the efficiency gains of multi-mode concepts, new and improved ignition technologies are required. Recently, non-equilibrium low-temperature plasmas (LTP) have been shown to promote energy-efficient ignition via quenching and transport of electronically excited atoms and molecules, selective radical production and fast heating of hydrocarbon/air mixtures [1-2]. Thus, LTP is seen as a technology that can potentially improve the energy extraction efficiency of fuels, while enabling kinetically controlled combustion modes towards fuel leaner conditions to realize current DOE VTO goals of improving the sustainability of future mobility [3]. Although many previous studies have demonstrated the efficacy of plasma-assisted ignition to enhance combustion, the detailed enhancement mechanisms remain largely unknown, especially for oxygenated fuels and at elevated pressures that are most relevant to practical engine conditions. These barriers hinder the development of accurate and comprehensive numerical models that seek to describe LTP-based ignition in existing engine design software tools and methods. Current state-of-the-art simulation capabilities for LTP ignition systems are in need of improvements since they deliver qualitative results only due to important limitations of existing approaches. Firstly, validated kinetic models with elementary steps for plasma discharges in oxygenated fuel/air mixtures of relevance to the transportation sector are required. Such kinetic models do not exist at present and will be developed and validated within this project. Secondly, plasma discharges and reactive mixture ignition are multi-scale, unsteady processes requiring high-performance numerical methods and software that execute efficiently on DOE supercomputers. Such software does not exist at present and will be developed and applied to practical LTP ignition scenarios as part of this project. Thirdly, experimental databases that are tailored to serve as benchmark in support of the development of predictive computational models of LTP ignition do not exist and will be part of this project.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Computationally Accelerated Discovery and Experimental Demonstration of High-Performance Materials for Advanced Solar Thermochemical Hydrogen Production

This project achieved its overarching goal of accelerating the discovery and validation of solar thermochemical hydrogen (STCH) materials through a tightly integrated approach that combined high-throughput computational screening, advanced machine learning (ML), and experimental testing. Guided by the objectives outlined in the Statement of Project Objectives (SOPO), our work fulfilled all major milestones across four technical tasks and delivered scientific breakthroughs and practical tools that significantly exceeded the original scope of the project. We began by addressing the challenge of predicting material phase stability through machine learning. A novel Python module was developed to generate thousands of meaningful features from composition, structure, and electronic properties, enabling rapid and reproducible ML model development. Using these tools, we trained a model to predict temperature-dependent Gibbs energies (G(T)) for inorganic crystalline materials with near-chemical accuracy—roughly 40 meV/atom—marking the first such descriptor of its kind. We also introduced a new machine-learned tolerance factor, τ, that accurately predicted perovskite formability with over 90% success, outperforming traditional heuristic models, such as the Goldschmidt tolerance factor. These capabilities allowed for rapid and accurate predictions of phase stability across a vast oxide composition space, setting the stage for high-throughput thermodynamic screening. Building on this foundation, we conducted an extensive computational screening of candidate STCH oxide materials. Over 1.1 million perovskite compositions were evaluated using the τ descriptor, leading to the identification of more than 27,000 predicted stable structures. Using density functional theory (DFT), we refined over 68,000 multinary perovskite structures and computed oxygen vacancy formation energies for over 1,300 ternary and double perovskites. These calculations enabled us to isolate compounds with redox behavior consistent with STCH requirements and resulted in a public dataset now hosted on the Materials Project. Recognizing that thermodynamic screening alone is insufficient, we addressed kinetic limitations by developing a suite of tools to estimate transition state (TS) energies for key redox reactions. We implemented a novel bounding approach that provides lower and upper estimates of TS energies with dramatically reduced computational cost, requiring less than 10% of the CPU time of a full nudged elastic band (NEB) calculation while maintaining high accuracy. This enabled rapid evaluation of over 200 reaction pathways across 90 materials. To further accelerate screening, we developed a SISSO-based ML model to predict diffusion barriers with a 96.7% success rate in classifying fast vs. slow materials, supporting a robust, data-driven framework for assessing redox kinetics. Experimental validation was critical to confirming the predictive power of our models. We synthesized and tested a wide array of candidate materials, including Mn-doped hercynite and several Gd- and La-based perovskites. Notably, Sr 0.4 Gd 0.6 Mn 0.6 Al 0.4 O 3 (SGMA) and Gd 0.5 La 0.5 Co 0.5 Fe 0.5 O 3 (GLCF) emerged as leading STCH materials, exhibiting robust redox cycling and high hydrogen yields exceeding 150 µmol H 2 /g per cycle. These materials also retained over 50% of their hydrogen productivity under high-conversion conditions (H 2 O:H 2 = 1333:1), demonstrating strong thermodynamic favorability and promising performance under industrially relevant scenarios. Additional candidates, such as La 2 MnNiO 6 (L2MN), were found to produce even higher yields than ceria under standard STCH conditions. Our collaborators at Sandia National Laboratories confirmed these findings using high-temperature X-ray diffraction and thermogravimetric analysis, observing stable phase evolution and reversible redox activity. In several respects, the project went beyond the goals initially outlined in the SOPO. We published 17 peer-reviewed articles, including a large dataset of over 66,000 theoretical perovskites and a new structure prediction method (SPuDS-DFT) that accurately identifies ground-state structures at a fraction of the cost of traditional DFT. We demonstrated that our machine-learned G(T) model offers accuracy rivaling quasiharmonic calculations while being orders of magnitude faster. In partnership with the Materials Project, we made our datasets openly available, providing a powerful new resource for the broader materials science community. The combined computational and experimental advances of this project represent a significant advance in STCH materials discovery. By creating a robust, generalizable, and open workflow for thermodynamic and kinetic screening, and validating key findings through synthesis and reactor testing, we have provided a practical and scalable pathway for the rapid identification of new redox-active materials. The tools, data, and materials developed under this project are already supporting ongoing research and have laid the groundwork for the next generation of solar fuel technologies.

08 HYDROGEN↗
DOE OSTI2022

Scalable High-H 2 Flux, Robust Thin Film Solid Oxide Electrolyzer

This project was aimed at the development of proton-conducting SOEC (P-SOEC) technology that has the potential to meet key DOE H 2 production targets. A decreased proton resistance of the electrolyte and Faradaic efficiency improvements were sought to increase the fraction of consumed electrolysis power that is used to actually generate H 2 , while simultaneously decreasing cost dramatically. Moreover, the development project was intended to yield maximum durability through the use of a steam protective layer. Furthermore, sputtering was used to overcome processing challenges that have hampered P-SOEC development, while the low-temperature operation goal of 500 °C was expected to aid in mitigating thermally activated long-term degradation. The approach to high-performance, lower-temperature SOECs leveraged our existing SOFC Ni-cermet anode support and extensive thin-film sputtering layer-deposition experience. Rather than an all-in-one, reversible fuel cell approach which has many unacceptable tradeoffs, we focused on the many benefits to hydrogen generating SOECs, including the existence of synergies for reduced manufacturing costs (e.g., SOECs and SOFCs share supporting layers and overall manufacturing processing). The end result of this project was expected to increase current performance at 500 °C from approximately 0.8 A/cm 2 (at 60% Faradaic efficiency) at 1.4 V to > 1 A/cm 2 (at > 95% Faradaic efficiency) with a > 40% reduction in system cost and to enable operation of P-SOECs in steam contents >> 20% for a goal of a > 40,000 hours lifetime. To enable 500 °C operation in a very high steam atmosphere (> 20%), we proposed the use of a sputtered dense thin film (~0.1-1 µm thick) of high-stability Ba(Zr,Y)O 3 (BZY) to protect the Ba(Ce,Zr,Y,Yb)O 3 (BCZYYb) electrolyte. The BZCYYb, in turn, blocks the hole conductivity of the BZY to boost Faradaic efficiency. As FE increases, more of the consumed electricity is used in electrolysis to generate H 2 , rather than being shunted. Additionally, as cell resistance decreases, the voltage required to maintain current decreases, as well as the power required to generate the same amount of H 2 . With the proposed enhancements, these two factors result in the final 46% decrease in power needed to run the system. Likewise, a production rate of 50,000 kg H 2 /day will require 55% less active area, such that a system will need only 650 cells for an 80 cm 2 active area instead of ~1,440. Taking the 2016 DOE projected current cost and modifying the electricity cost and linearly scaling the other costs (except thermal feedstock) based on the cell area improvement, results in a 44% decrease in lifetime system cost, or a decrease from $\$$4.95/kg H 2 to $\$$2.75/kg H 2 . This is well below the 2018 DOE target of $\$$4/kg H 2 . The results from this project showed that we can create a P-SOEC with enhanced steam stability using two different electrolytes (i.e., one on top of the other) and achieve sufficiently low area specific resistance (ASR) to achieve the target performance. Unfortunately, due to extended delays at the beginning of the project and related supply chain and equipment access issues, we were not able to completely show increased Faradaic efficiency for the P-SOEC and therefore were unable to demonstrate the full proof of concept within the first budget period budget. While there are still challenges that remain to be solved, significant progress was made during this project and the concept still has merit that warrants further development.

08 HYDROGEN↗
DOE OSTI2025

Machine Learning for Real-time Fusion Plasma Behavior Prediction and Manipulation (Final Report)

The goal of this project is to implement real-time analysis of 2D Beam Emission Spectroscopy (BES) data to predict and control transient and high-bandwidth events at DIII-D. In essence, we wish to bring high-bandwidth fluctuation diagnostics into the realm of real-time measurements and control. The BES ML models will necessarily be deep neural networks (DNN) with a “data flow” architecture for compatibility with high-throughput, low-latency evaluation on a field-programmable gate array (FPGA) or other emerging processor technologies. The real-time output will be fed to the plasma control system (PCS) for real-time control tasks, specifically for ELM control and avoidance and for QH-mode access and sustainment. We anticipate that the real-time analysis of fluctuation diagnostics will create new enabling technologies to predict and control transient events such as confinement mode transitions, edge-localized modes, Alfven eigenmode events, and disruptions. The proposed research is aligned with ITER research needs and DIII-D programmatic goals. For instance, the prediction and avoidance of ELM events is critical for ITER machine safety. Also, H-mode access with RMP ELM suppression in ITER is an active research area due to high separatrix density, narrow SOL width, and elevated LH transition power threshold.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

High Energy Density Physics of Inertial Confinement Fusion Ablator Materials

The historic December 5, 2022 experiment at Lawrence Livermore National Lab’s (LLNL) National Ignition Facility (NIF) reached fusion energy ignition for the first time. This is the most important scientific breakthrough of the 21st century paves the way to future clean inertial fusion energy (IFE). The diamond (high density carbon (HDC)) ablator material used in this experiment displays detrimental effects due to the development of hydrodynamic instabilities at the diamond/fuel interface under shock compression. New alternatives to diamond ablators are required to step up the energy yield in ICF experiments. The unique combination of mechanical strength (approaching that of diamond), the ability to accommodate high-Z dopants (in contrast to diamond), and the tunability of the properties (through synthesis material with varying sp 3 content) make amorphous carbon (a-C) a promising material for next-generation IFE ablative capsules. However, despite its critical importance to the IFE program, the behavior of a-C carbon at extreme temperatures and pressures remains largely unexplored. The primary goals of this project were to perform groundbreaking dynamic compression experiments and predictive simulations to uncover the fundamental high-energy-density physics of amorphous carbon. Our goals were (1) to uncover the metastability range of amorphous carbon and probe phase transitions to diamond or metastable supercooled liquid carbon; (2) to acquire high-quality equation of state (EOS) data and develop an experimentally validated EOS from machine-learning MD simulations of the complex states of carbon; and (3) to uncover the complex behavior of carbon liquid in both thermodynamically stable and metastable supercooled states by accessing large areas of carbon phase diagram with amorphous samples with variable sp 3 content. Our proposed experimental program included measurements of equation of state and diffraction measurements using the Omega EP laser at the Laboratory of Laser Energetics at the University of Rochester. The theoretical/simulation program involved the development of machine-learning models of the complex response of amorphous carbon under dynamic compression by performing molecular dynamics simulations at experimental time and length scales using leadership class DOE supercomputers. Simulations guided experiments to observe predicted phenomena and acquire critical experimental data in specific pressure-temperature domains to validate theoretical models. This research delivered fundamental properties of novel amorphous carbon IFE ablator material, including phase diagram and EOS. These results will aid in IFE target design and implosion experiments. A unique combination of predictive simulations and dynamic and static experiments provided a highly inspirational intellectual environment for graduate students and postdocs involved in this project.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Integrating an Industrial Source and Commercial Algae Farm with Innovative CO 2 Transfer Membrane and Improved Strain Technologies

This report describes the overall findings of the research project “Integrating an Industrial Source and Commercial Algae Farm with Innovative CO 2 Transfer Membrane and Improved Strain Technologies”. The motivation and goal for this project were to increase the carbon utilization efficiency (CUE) and areal productivity for algal cultivations, thereby reducing CO 2 costs to cultivation operations and improving economics. This was achieved through a combination of enhanced delivery of inorganic carbon and improved strains of Nannochloropsis oceanica capable of higher rates of bicarbonate uptake and metabolism. The project succeeded in these goals. First, a bubble-free, membrane-based technology was developed for delivering CO 2 to cultivations, which increased the CUE from the 15-20% that is standard in the industry to more than 65%. In addition, N. oceanica was modified to express a bicarbonate transporter protein, BicA, which enabled the cells to grow more quickly. In addition, advances were made in the protein engineering of carbonic anhydrase (CA) for enhanced stability and catalytic performance, the computational fluid dynamics modeling of algal cultivation systems, and in the life-cycle assessment and technoeconomic analysis of algal production. Together, these outcomes contribute to advancing algal cultivation as an economically viable platform for production of fuels, materials, and other chemical products. The project results aid in addressing the dual challenges of reducing atmospheric CO 2 levels and achieving green energy solutions.

09 BIOMASS FUELS↗
DOE OSTI2025

PATHS: Career Pathways to Advance the Trades in HVAC Services

The Career Pathways to Advance the Trades in HVAC Services (“PATHS”) project was designed to advance EERE/BTO goals of dramatically reducing the energy consumed in homes nationwide. Installing HVAC systems correctly and going back to provide tune-ups (maintenance) can improve their performance by at least 30%, so HVAC Technicians are critical to achieving GHG goals. However, there is a lack of trained technicians: residential HVAC installers and service technicians are retiring faster than they are being recruited, and workers with the advanced skills needed to install and service more complicated heat pump systems are even more scarce. Paradoxically, at the same time, unemployment and underemployment are still problems, particularly in disadvantaged communities.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

The KIPM Detector Consortium

Kinetic Inductance Phonon-Mediated (KIPM) Detectors, microcalorimeters that leverage kinetic inductance detectors (KIDs) to read out phonon signals from the device substrate, are an attractive architecture for low-threshold rare-event searches due to their large response to small changes in quasiparticle density and native multiplexability, enabling scalability. We have established a consortium comprising university and national lab groups dedicated to advancing the state-of-the-art in these detectors, with the ultimate goal of designing a detector with a kg-scale target mass and sub-eV threshold on energy deposited in the substrate, enabling searches for both light dark matter and low-energy neutrino interactions. This consortium brings together experts in KID design, phonon and quasiparticle dynamics, and noise modeling, along with specialized fabrication facilities, test platforms, and unique calibration capabilities. Recently, our consortium has demonstrated a sensor resolution (i.e., resolution in the quasiparticle channel) of 2.1 eV, the current record for such devices. The current focus of the consortium is modeling and improving the phonon collection efficiency and implementing low-Tc superconductors, both of which serve to improve the overall energy resolution and threshold of the detectors. In this talk, I will provide an overview of the consortium and its capabilities, highlight some recent results from its member groups, and discuss near term plans toward reaching the ultimate goal.

Temples, Dylan J. [Fermilab]↗
DOE OSTI2025

Cell to Ecosystem: Understanding Methane and Associated Nutrient Cycling by Sediment Hosted Syntrophic Consortia and Their Viral Predators

The anaerobic oxidation of methane (AOM) is a significant worldwide microbial process in anoxic lake and ocean sediments, responsible for sequestering up to 80% of this greenhouse gas. Often considered a metabolism on the edge of thermodynamic probability, the impact of ANaerobic MEthane-oxidizing ‘ANME’ archaea on carbon and nutrient cycling in sediment ecosystems is far reaching. They not only serve as a sink for methane coupled to diverse electron acceptors, but also catalyze the transformation of many important nutrients including nitrogen, phosphate, and iron. While information about the potential mechanisms supporting metabolism in AOM is now available, remarkably little has been learned about their nutritional requirements, their dependencies on bacterial partners, and consequentially their ultimate impact on nutrient transformation and bioavailability within sedimentary ecosystems, and beyond. Further, the role of viruses within sediment ecosystems represents an essential but vastly understudied aspect of the transformation of carbon and nutrients by AOM. Viruses are now widely appreciated as central players in biogeochemical cycles across diverse ecosystems. These nanoscale predators have been shown to enhance the turnover of essential nutrients, thus stimulating microbial growth and environmental viruses themselves may constitute an important reservoir of nitrogen and phosphorous. Little is known about the role of viruses in methane-impacted sedimentary ecosystems, however prior genomic and microscopy evidence suggests that AOM consortia are susceptible to phage infection. The overarching scientific goal of this multi-disciplinary research proposal is to build on these recent discoveries and expand our understanding of interactions and fundamental activities involved in cycling of carbon and nutrients by syntrophic methanotrophic archaeal-bacterial consortia and associated viruses in anoxic sedimentary environments. Our three specific objectives are to 1) Quantify energy and nutrient exchange (e.g. N, P, Fe and vitamins) within AOM consortia and between ANME-bacterial partners; 2) Identify virus-host interactions associated with AOM and assess C and N transfer through viruses in methane-impacted sediment ecosystems; 3) Model energy and nutrient exchange in AOM consortia and viral-host interactions (i.e. viral activity), and their environmental distribution patterns. Our experimental emphasis cuts across scales that are important for understanding microbial and viral interactions and activities within their habitats, as well as community wide biogeochemical transformations. These research goals will be accomplished through the application of novel molecular techniques targeting DNA, RNA, proteins, and metabolites combined with a unique multi-modal analytical imaging pipeline. We will then model the ecophysiological capabilities of diverse sediment-hosted methanotrophic consortia to develop a more comprehensive understanding of the energetic and nutritional interactions between different AOM partner couplings that occur in sediments.

03 NATURAL GAS↗
DOE OSTI2024

Neutrons in Structural Biology: Challenges and Opportunities (Workshop Report)

Gaining a thorough understanding of biological systems requires building our knowledge about biological processes from the level of atoms and electrons, and up to whole organisms. Such comprehensive knowledge will allow for a predictive understanding of complex biological systems behavior. It will guide us in the design and development of novel therapeutics and vaccines to tackle existing health threats and to prepare for future pandemics, and it will provide information necessary to create new biomaterials and bio-inspired technologies through manipulation of biological macromolecules, their assemblies, single cells and even microorganisms. Reaching these goals will require a synergistic combination of multiple experimental techniques with molecular calculations and predictive simulations, and the design and development of new techniques and capabilities that bridge current knowledge and technology gaps. Neutron scattering provides unique information about the biomacromolecular structure and function and can play a major role in achieving these goals. A workshop was held to engage the scientific community in identifying pressing challenges in biochemistry, structural biology, enzymology and structure-guided drug design not solved with the current neutron scattering technologies or utilizing other structural biology techniques such as X-ray crystallography, NMR, and cryo-EM. The workshop brought together structural biology, biochemistry and computational experts, as well as early career researchers and students, creating a forum for discussing scientific advancement and collaboration. The workshop included a one-day satellite training workshop where graduate students and postdoctoral researchers were educated in the application of neutron crystallography and small-angle scattering in structural biology. Furthermore, the Instrument Scientific Advisory Board (ISAB) for the development of a macromolecular neutron diffractometer at ORNL’s Second Target Station was introduced at the workshop. The major outcome was that neutrons can provide atomic-level understanding of biomacromolecular structure, function and dynamics which is of paramount importance for addressing the identified challenges. Neutron crystallography, in particular, can resolve long-standing biochemical issues regarding enzyme function by delineating the underlying chemistry and can have a major impact on the design of small-molecule therapeutics, especially in combination with molecular computation (quantum chemistry and molecular dynamics simulations) and the emerging artificial intelligence (AI)-assisted drug design technologies. The unique properties of neutrons, including their high sensitivity to hydrogen and their non-destructive nature, make them ideal probes of biological matter. There is a palpable need in the scientific community to expand and enhance the impact of neutron sciences on biology. Neutron crystallography is the only structural biology method capable of determining positions of all hydrogen atoms in proteins, nucleic acids and their complexes at near-physiological temperatures and of unstable species at cryogenic temperatures. Moreover, neutron analysis is non-ionizing, non-destructive and does not perturb the structure or redox chemistry of active site metal centers and clusters in proteins, which can be invaluable for studying radiation-sensitive metalloprotein complexes. Further, neutron energies used in scattering applications are similar to atomic motions, permitting neutron spectroscopies to characterize the dynamics of biomacromolecules on the picosecond to microsecond timescales. The different sensitivities of neutrons to protium (H) and deuterium (D) isotopes of hydrogen allow enhanced visibility of specific parts of biological complexes through isotopic labeling. The impact of neutrons will be most powerful when neutron scattering is combined with complementary experimental techniques that use photons and electrons, and with high-performance computing. The interconnection and mutuality of the experimental and theoretical capabilities will drive discoveries in biological and health sciences to generate more complete picture of complex biological systems. The major limitation in the field of biological neutron crystallography has been signal-to-noise, demanding large samples that are difficult to produce for the majority of biomacromolecules and limiting the applicability of this technique in biological sciences. A neutron crystallography instrument at the Second Target Station will revolutionize biological science with neutrons by engaging a large scientific community of structural biologists, enabling successful neutron diffraction experiments from radically smaller biomacromolecular crystals, resolving unanswered biochemical questions, and meaningfully contributing to rational drug design. The meeting highlighted 10 grand challenges that will be addressed with this advanced capability over the next decade and beyond, and the recommendations required to help address them are given below.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Code Coverage Status of the ARC Code DIF3D

The Argonne Reactor Code (ARC) software system supports users in their fast reactor design goals by providing neutronic, thermal-hydraulic, and structural analysis capabilities. DIF3D plays a pivotal role in the ARC system as the primary homogenized assembly neutronic calculation methodology for fast reactor problems. Over its 40 years history, ARC software usage with DIF3D has been applied to numerous fast and thermal spectrum reactor analysis projects with good to excellent comparison against experiments. With continued improvement of computation resources, many of the geometry modeling capabilities in DIF3D that were primarily used in low order schemes are not really needed anymore. Today, the diffusion and transport capabilities of DIF3D-VARIANT are primarily used in the reactor design process with some scattered usage of DIF3D-FD and DIF3D-Nodal. In recent work, the DIF3D software verification was completed for DIF3D-FD and DIF3D-VARIANT on the geometry options used in the Versatile Test Reactor project. While we can be confident that these capabilities of DIF3D are well used and thus trusted, it does not demonstrate that all possible input options of DIF3D are actually working, but just those that were tested as part of VTR are and that they are correct. Thus, the purpose of the present work is to identify a set of test problems for DIF3D and assess the code coverage of DIF3D for those test problems. The goal is to document what parts of the existing DIF3D code are touched by the set of test problems and which are not. Because the verification work done on DIF3D-VARIANT and DIF3D-FD was focused on the most common uses of DIF3D for fast reactor analysis, the code coverage assessment of those capabilities is the highest priority. This will ensure that nothing is being missed by the existing verification test problems that DIF3D relies upon. The DIF3D-Nodal capability will also be inspected for code coverage as part of this work to further ensure that regular regression testing of DIF3D will trap any likely errors the end user might experience with the DIF3D software. The code coverage analysis of DIF3D was performed with the Code Coverage Tool of the Intel Fortran compiler which requires modifications to the compilation of DIF3D. The detailed coverage tables are given for each submodule of DIF3D separately, and for the submodules which are primarily developed for DIF3D, most of the source files could be at least partially touched. Most of the uncovered parts/files could be easily ignored, because they are either for error message and debugging output or obviously not needed by DIF3D. Out of the entire source codes of DIF3D, only a few uncovered modules deserve further investigation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗