Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fusion application”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Correlation between microstructure and residual stress formation in friction stir welded armor steels characterized by neutron diffraction

Friction stir welding (FSW) is a solid-state joining process that minimizes the heat-affected zone (HAZ) compared with fusion-based arc welding, making it well suited for joining martensitic armor steels where hardness and ballistic resistance are critical. This study investigates residual stress formation in three defect-free FSW butt-joint configurations relevant to armored-vehicle fabrication: similar rolled homogeneous armor (RHA–RHA, Case 1), similar high-hardness armor (HHA–HHA, Case 2), and dissimilar HHA–RHA (Case 3) joints produced under temperature-controlled conditions (770 °C). Neutron diffraction was employed to quantify the magnitude and spatial distribution of residual stresses in the longitudinal, transverse, and normal directions and to correlate them with weld microstructure and hardness. Tensile residual stresses were concentrated in the softened HAZ, reaching approximately 300 MPa for Case 2 and 400 MPa for Case 1 (≈50–70 % of the base-metal yield strength; ∼581 MPa for RHA and ∼566 MPa for HHA), while compressive residual stresses dominated the stir zone. The spatial extent of tensile stresses scaled with the width of the softened HAZ, which was largest in the dissimilar HHA–RHA joint and smallest in the HHA–HHA joint. Full-width-at-half-maximum (FWHM) analysis revealed low microstrain in overtempered HAZ regions and high microstrain in the stir zone associated with severe plastic deformation and fresh martensite formation. This work demonstrates that residual stress evolution in FSW of martensitic armor steels is governed not primarily by peak temperature or thermal contraction, as inferred from fusion-welding analogies, but by the competition between transformation-induced volumetric expansion and tempering-induced stress relaxation. The relative dominance of these mechanisms is shown to depend on alloy hardenability and local thermal history, leading to more extensive HAZ softening and broader tensile stress regions in the lower-hardenability RHA steel. These findings establish a transferable mechanistic framework for optimizing solid-state joining strategies in high-strength steels and other transformation-hardening alloys beyond armor applications.

Friction stir welding↗
DOE OSTI2026

The effect of varying powder feedstock chemistry and printing atmosphere on the microstructure of additively manufactured nickel-based ODS alloys: Role on stabilization of cellular structures vs. oxide dispersion formation

Nickel-based alloys have a wide variety of structural applications due to their high corrosion resistance and mechanical strength which depend on solid solution strengthening, or the formation of oxides and/or intermetallic precipitation for their properties. In this study, the microstructure of six Ni–Cr–Y–Ti–Al powder batches designed for the production of oxide dispersion strengthened nickel were compared. These batches varied in chemistry and atomization technique used which included Gas Atomization Reactive Synthesis (GARS). The batches of powder were then consolidated via Additive Manufacturing (AM) Powder Bed Fusion using Laser Beam (PBF-LB) and characterized via transmission electron microscopy to elucidate the influence of powder feedstock (i.e. synthesis methodology and chemistry) on the PBF-LB microstructure. The study investigates (i) how the amount of yttrium and titanium additions in the powder feedstock and the addition of oxygen during the processing (through GARS) affect the microstructure of the powder itself and the AM printed microstructure, and (ii) how the control of oxygen addition in the printing atmosphere during the PBF-LB printing process itself is another important parameter for achieving the formation of the wanted oxide dispersion versus the stabilization of the cellular structure (often observed in AM processed alloys). Microstructural characterization of both powder particles and additively manufactured nickel alloys in this study provide important insights into the movement of yttrium within the material upon solidification, particularly along cell boundaries, and how yttrium behaves depending on alloy chemistry. When a threshold of yttrium content is reached within the system, yttrium consistently reacts to form an intermetallic along cell boundaries instead of forming oxide nanoparticles.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Development of a deep learning based automated data analysis for step-filter x-ray spectrometers in support of high-repetition rate short-pulse laser-driven acceleration experiments

We present a deep learning based framework for real-time analysis of a differential filter based x-ray spectrometer that is common on short-pulse laser experiments. The analysis framework was trained with a large repository of synthetic data to retrieve key experimental metrics, such as slope temperature. With traditional analysis methods, these quantities would have to be extracted from data using a time-intensive and manual analysis. Furthermore, this framework was developed for a specific diagnostic, but may be applicable to a wide variety of diagnostics common to laser experiments and thus will be especially crucial to the development of high-repetition rate (HRR) diagnostics for HRR laser systems that are coming online.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Mechanical characterization of fine-grain dispersion-strengthened tungsten as a plasma facing material

Field-Assisted Sintering Technology (FAST) was used to produce fine-grained, dispersion-strengthened tungsten (W) materials. Investigated materials 4138, 4353, and 4355 composed of 3 wt% ZrC sintered at 1800 °C, 5 wt% ZrC sintered at 1800 °C, and 3 wt% ZrC sintered at 2000 °C, respectively. They were compared against ITER-grade W. A series of mechanical and thermal property testing and microstructure studies were conducted to study them as a potential plasma facing material (PFM) for fusion reactors. Hardness testing showed that manufacturing conditions substantially altered hardness. Material 4355 had an average HV10 value of 497.2 ± 16.8, slightly higher than ITER-grade at 378.5 ± 40.3. However, material 4353 was substantially higher with an HV10 value of 738.9 ± 31.7 over the investigated temperature range. Electron Backscatter Diffraction (EBSD) analysis showed that FAST produced substantially smaller grains than the hot-rolled ITER-grade W material, offering notable control over grain size. Materials 4353 and 4355 had grain sizes of 0.44 ± 0.20 µm and 3.67 ± 0.89 µm, respectively, whereas ITER-grade 27.14 ± 19.76 µm at room temperature. The fine grain structures showed no net coarsening after 1 hr. anneals up to 1800 °C, several hundred degrees above the 1100 – 1500 °C recrystallization range reported for conventional W. Inverse application of the Zener pinning relationship to the measured grain sizes indicates that these two FAST sintering conditions produce markedly different effective dispersoid populations, with effective particle diameters of approximately 90 nm at a peak sintering temperature of 1800 °C and approximately 460 nm at 2000 °C, respectively. This result demonstrates that the FAST thermal condition itself, and not the nominal ZrC content alone, governs the pinning effectiveness of the dispersion. Thermal diffusivity measurements support this finding independently. Materials of identical composition sintered at different temperatures differ by approximately 19% in measured thermal diffusivity with statistically indistinguishable density, while materials of different composition and sintering temperature converge to within approximately 2%. At a representative divertor heat flux of 10 MW/m², the lower thermal conductivity of the fine-grained materials corresponds to approximately 28 to 33 °C per millimeter of armor thickness relative to ITER-grade W, traded against a substantially larger margin to recrystallization-driven degradation. While high temperature tensile testing revealed likely contamination that motivates refinement of the manufacturing process, FAST-produced, fine-grained, dispersion-strengthened W offers process-controlled microstructural stability well above the operating temperatures of conventional W and supports its continued development as a PFM for economically viable commercial fusion power.

Parker, Gabe [ORNL] (ORCID:0000000190394100)↗
DOE OSTI2022

Processing of phase change materials by fused deposition modeling: Toward efficient thermal energy storage designs

We report that recently, several efforts have emerged that employ additive manufacturing techniques to integrate phase change material (PCM) thermal energy storage into geometrically complex designs for advanced thermal management. In this work, we contribute to this emerging research by reporting on the production of a composite nylon-based filament for fused deposition modeling incorporating encapsulated PCMs for 3D printing heat sink geometries. Microencapsulated PCM (MEPCM) with a 6 degrees C transition temperature was selected as the material for thermal energy storage. This transition temperature was selected due to its suitability to provide thermal energy storage to target air-conditioning applications in buildings. In an attempt to improve the thermal conductivity of the composite, fine boron nitride fillers were added, although the effect on improvement was found to be negligible in the overall composite mixture. The nylon-MEPCM ratio in the filaments was optimized, and filaments containing up to 40 wt% MEPCM were successfully synthesized, which were found optimal for 3D printing complex heat sink and other geometries. Thermal and mechanical properties of the filaments were characterized, including latent heat of fusion, thermal conductivity, phase change temperature, tensile strength, and more. Thermal infrared imaging of heat sink geometries printed using the MEPCM filaments undergoing thermal discharging was also conducted. This work presents the most promising result to date in the open literature for a 3D-printed PCM composite in the combination of size, energy density, and geometric complexity of printed parts.

25 ENERGY STORAGE↗
DOE OSTI2022

Quasi-linear toroidal simulations of resonant magnetic perturbations in eight ITER H-mode scenarios

Abstract Both linear and quasi-linear aspects of the plasma response to the resonant magnetic perturbation (RMP) field are numerically investigated for various H-mode scenarios in ITER, covering the pre-fusion power operation and the fusion power operation phases. Linear response computations for eight ITER scenarios, with varying plasma current and toroidal magnetic field, reveal that the best coil current phasing for controlling the type-I edge localized modes (ELMs) scales roughly linearly with the edge safety factor. The coil phasing is defined as the relative toroidal phase of the coil currents between different rows, for a given toroidal harmonic. Quasi-linear initial value simulation, which is the focus of the present study, shows that application of the n = 3 ( n is the toroidal mode number) RMP field has a minimum side effect on the plasma core momentum confinement but potentially a large effect on the global particle transport. Generally, the RMP field with the best (worst) coil phasing for ELM control produces the strongest (weakest) effect on the plasma edge flow and the overall density. This robustly holds for all eight ITER scenarios. Consequently, in order to minimize the RMP induced side effects while achieving ELM control (suppression) in ITER, a compromise is necessary in choosing the coil current configuration.

Physics↗
DOE OSTI2026

Genome_shuffling_enables_quantitative_trait_locus_mapping_in_Bacillus_subtilis

Genetic mapping is a powerful tool for eukaryotic genetics that has only been applied to bacteria in limited circumstances. Quantitative trait locus (QTL) mapping generally relies on sexual recombination to break linkages between genes, yet bacteria rarely undergo sufficient homologous recombination to generate suitable mapping populations. In this work, we used iterative biparental genome shuffling by protoplast fusion inBacillus subtilisto generate a population of bacteria with substantial random recombination throughout their genomes. Individual shuffled progeny were arrayed in well plates, resequenced, and characterized for a range of complex phenotypes including spore germination and swarming motility. Genetic mapping of the resulting phenotypes identified high-confidence QTLs of moderate size (∼10 kb), and these associations were validated through targeted genetic swaps. ThisB. subtilisQTL population can easily be used to map additional phenotypes, and the general approach for QTL mapping is applicable in a wide range of bacteria.

Bacillus subtilis↗
DOE OSTI2022

Fluid-Kinetic Coupling: Advanced Discretizations for Simulations on Emerging Heterogeneous Architectures (LDRD FY20-0643)

Plasma physics simulations are vital for a host of Sandia mission concerns, for fundamental science, and for clean energy in the form of fusion power. Sandia's most mature plasma physics simulation capabilities come in the form of particle-in-cell (PIC) models and magnetohydrodynamics (MHD) models. MHD models for a plasma work well in denser plasma regimes when there is enough material that the plasma approximates a fluid. PIC models, on the other hand, work well in lower-density regimes, in which there is not too much to simulate; error in PIC scales as the square root of the number of particles, making high-accuracy simulations expensive. Real-world applications, however, almost always involve a transition region between the high-density regimes where MHD is appropriate, and the low-density regimes for PIC. In such a transition region, a direct discretization of Vlasov is appropriate. Such discretizations come with their own computational costs, however; the phase-space mesh for Vlasov can involve up to six dimensions (seven if time is included), and to apply appropriate homogeneous boundary conditions in velocity space requires meshing a substantial padding region to ensure that the distribution remains sufficiently close to zero at the velocity boundaries. Moreover, for collisional plasmas, the right-hand side of the Vlasov equation is a collision operator, which is non-local in velocity space, and which may dominate the cost of the Vlasov solver. The present LDRD project endeavors to develop modern, foundational tools for the development of continuum-kinetic Vlasov solvers, using the discontinuous Petrov-Galerkin (DPG) methodology, for discretization of Vlasov, and machine-learning (ML) models to enable efficient evaluation of collision operators. DPG affords several key advantages. First, it has a built-in, robust error indicator, allowing us to adapt the mesh in a very natural way, enabling a coarse velocity-space mesh near the homogeneous boundaries, and a fine mesh where the solution has fine features. Second, it is an inherently high-order, high-intensity method, requiring extra local computations to determine so-called optimal test functions, which makes it particularly suited to modern hardware in which floating-point throughput is increasing at a faster rate than memory bandwidth. Finally, DPG is a residual-minimizing method, which enables high-accuracy computation: in typical cases, the method delivers something very close to the $L^2$ projection of the exact solution. Meanwhile, the ML-based collision model we adopt affords a cost structure that scales as the square root of a standard direct evaluation. Moreover, we design our model to conserve mass, momentum, and energy by construction, and our approach to training is highly flexible, in that it can incorporate not only synthetic data from direct-simulation Monte Carlo (DSMC) codes, but also experimental data. We have developed two DPG formulations for Vlasov-Poisson: a time-marching, backward-Euler discretization and a space-time discretization. We have conducted a number of numerical experiments to verify the approach in a 1D1V setting. In this report, we detail these formulations and experiments. We also summarize some new theoretical results developed as part of this project (published as papers previously): some new analysis of DPG for the convection-reaction problem (of which the Vlasov equation is an instance), a new exponential integrator for DPG, and some numerical exploration of various DPG-based time-marching approaches to the heat equation. As part of this work, we have contributed extensively to the Camellia open-source library; we also describe the new capabilities and their usage. We have also developed a well-documented methodology for single-species collision operators, which we applied to argon and demonstrated with numerical experiments. We summarize those results here, as well as describing at a high level a design extending the methodology to multi-species operators. We have released a new open-source library, MLC, under a BSD license; we include a summary of its capabilities as well.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Report on laser-induced fluorescence transitions relevant for the microelectronics industry and sustainability applications

A wide variety of feed gases are used to generate low-temperature plasmas for the microelectronics and sustainability applications. These plasmas often have a complex combination of reactive and nonreactive species which may have spatial and temporal variations in density, temperature, and energy. Accurate knowledge of these parameters and their variations is critically important for understanding and advancing these applications through validated and predictive modeling and the design of relevant devices. Laser-induced fluorescence (LIF) provides both spatial and temporally resolved information about the plasma-produced radicals, ions, and metastables. However, the use of this powerful diagnostic tool requires the knowledge of optical transitions including excitation and fluorescence wavelengths which may not be available or scattered through a huge literature domain. In this paper, we collected, analyzed, and compiled the available transitions for laser-induced fluorescence for more than 160 chemical species relevant to the microelectronics industry and the sustainability applications. A list of species with overlapping LIF excitations and fluorescence wavelengths have been identified. Finally, this summary is intended to serve as a data reference for LIF transitions and should be updated in the future.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

General-Purpose Unsupervised Cyber Anomaly Detection via Non-Negative Tensor Factorization

Distinguishing malicious anomalous activities from unusual but benign activities is a fundamental challenge for cyber defenders. Prior studies have shown that statistical user behavior analysis yields accurate detections by learning behavior profiles from observed user activity. These unsupervised models are able to generalize to unseen types of attacks by detecting deviations from normal behavior, without knowledge of specific attack signatures. However, approaches proposed to date based on probabilistic matrix factorization are limited by the information conveyed in a two-dimensional space. Non-negative tensor factorization, on the other hand, is a powerful unsupervised machine learning method that naturally models multi-dimensional data, capturing complex and multi-faceted details of behavior profiles. Herein, our new unsupervised statistical anomaly detection methodology matches or surpasses state-of-the-art supervised learning baselines across several challenging and diverse cyber application areas, including detection of compromised user credentials, botnets, spam e-mails, and fraudulent credit card transactions.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2026

The impact of kinetic and global effects on ideal ballooning 2nd stable pedestals of conventional and low aspect-ratio tokamaks

The EPED model (Snyder et al 2011 Nucl. Fusion 51 103016) has had success in describing the pedestal structure of Type-I ELM and QH-mode plasmas in tokamaks, by combining kinetic ballooning mode (KBM) and peeling–ballooning (PB) constraints. Within EPED, the KBM constraint is often approximated by a technique using calculated ideal ballooning mode (IBM) thresholds, fit to a functional form designed to capture non-local effects. It has been noted that quantitative differences between local ideal MHD and gyro-kinetic (GK) ballooning stability can be larger at low aspect ratio. KBM critical pedestals are consistent with observations in initial studies on conventional and spherical tokamaks. In this work, the application of a reduced model for the calculation of the kinetic ballooning stability boundary is presented based on a novel and newly developed gyro-fluid system (GFS) code (Staebler et al 2023 Phys. Plasmas 30 102501). GFS is observed to capture KBMs in DIII-D as well as the NSTX pedestals, opening a route to integrating this model into EPED. Finally, high but finite $n$ global ballooning modes are observed to limit the access to the local 2nd stability and thus provide a transport mechanism that constrains the pedestal evolution with $β_{p,\textrm{ped}}$. The high $n$ global ballooning stability is approximated by its ideal MHD analog using ELITE. It is shown that nearly-local high $n$ modes with $k_yρ_s$ ~ $0.25 - 0.5$ can provide a proxy for the critical $β_{p,\textrm{ped}}$ when a 2nd stable access exists on DIII-D plasmas. The use of GFS and ELITE scaling in EPED provides improved agreement to EPED1 in an initial comparison with DIII-D pedestal data.

Anastopoulos Tzanis, Michail Savvas [Oak Ridge Nat↗
DOE OSTI2024

Analysis and design of fast flow liquid Li divertor for fusion nuclear science facility (FNSF) using coupled plasma boundary and LM MHD/heat transfer codes *

The SOLPS-ITER code is utilized to analyze the boundary plasma associated with a fast-flow lithium (Li) divertor configuration in the fusion nuclear science facility (FNSF) tokamak and identify operational regimes with acceptable divertor and core conditions. Plasma transport from the SOLPS-ITER code has been coupled with a liquid metal (LM) MHD/heat transfer code to model a Li open-surface divertor design and assess its impact on the scrape-off-layer (SOL) and core plasma performance. Simulations with only Neon (Ne) impurity seeding have been conducted to evaluate its impact on meeting FNSF design demands for the divertor and upstream plasma parameters. Simulation results indicate that Ne seeding significantly mitigates divertor heat flux but potentially reduces both upstream electron and main ion density due to fuel dilution. The combined application of Ne seeding and deuterium (D 2 ) puffing is required to satisfy the FNSF design requirements on upstream density ($n^{OMP}_{e,sep}$~1× 10 20 m -3 ) and divertor energy flux ($q^{Odiv}_{\bot,max}$<10 MW m -2 ). D 2 puffing plays a role in counteracting upstream density drops and augmenting energy and momentum losses through atomic and molecular processes. The inlet Li flow velocity is systematically varied across a wide range to identify acceptable flows and corresponding LM surface temperatures. This comprehensive analysis identifies the acceptable Li flow parameters, LM surface temperature, and emitted Li fluxes necessary to meet the major design constraints. The emitted Li fluxes exhibit minimal impact on the main plasma at surface temperatures up to approximately ~525 °C, corresponding emitted Li fluxes of up to φ Li ~2X10 23 atoms s -1 . Uncertainties in the Li emission processes from the surface are also investigated, primarily influencing Li loss in the lower surface temperature range (<525 °C), with simulation results indicating a minor impact on the divertor and upstream plasma. Conversely, evaporation predominantly drives the Li loss processes at higher surface temperature ranges (>525 °C), contaminating both the divertor and upstream plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Progress and innovations in the TCV tokamak research programme

Research on the Tokamak à Configuration Variable addresses a wide range of key questions relevant to ITER and future fusion power plants. Over the past two years, highly productive experimental campaigns have led to major advances across several areas: the ITER baseline scenario; pedestal properties in low-collisionality, peeling-limited conditions; and the development of high- β N , non-inductive regimes. Alternative high-confinement scenarios have likewise received significant attention, with remarkable progress in quasi-continuous exhaust operation, X-point radiator plasmas, and negative triangularity configurations. Substantial achievements were also made in the mitigation or benign termination of runaway electron beams, in elucidating fast-ion loss mechanisms, and in improving exhaust behaviour in both conventional and alternative divertor geometries. These experimental results have been strongly supported by advances in modelling and their direct application to the experiment, ranging from gyrokinetic simulations of core and pedestal turbulence to fluid-based studies of scrape-off layer and divertor physics in diverse geometries. Plasma control has taken on an increasingly important role, with model-based and data-driven approaches now closely intertwined with physics studies. This article provides a overview of these recent activities, together with a brief outlook on forthcoming upgrades and next steps.

EPFL↗
DOE OSTI2020

General formulas for adiabatic invariants in nearly periodic Hamiltonian systems

While it is well known that every nearly periodic Hamiltonian system possesses an adiabatic invariant, extant methods for computing terms in the adiabatic invariant series are inefficient. The most popular method involves the heavy intermediate calculation of a non-unique near-identity coordinate transformation, even though the adiabatic invariant itself is a uniquely defined scalar. Here, a less well-known method, developed by S. Omohundro, avoids calculating intermediate sequences of coordinate transformations but is also inefficient as it involves its own sequence of complex intermediate calculations. In order to improve the efficiency of future calculations of adiabatic invariants, we derive generally applicable, readily computable formulas for the first several terms in the adiabatic invariant series. To demonstrate the utility of these formulas, we apply them to charged-particle dynamics in a strong magnetic field and magnetic field-line dynamics when the field lines are nearly closed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

The fastVFP code for solution of the Vlasov–Fokker–Planck equation

Abstract We describe the fast VFP code for solution of the Vlasov–Fokker–Planck equation for non-local electron transport and the generation of magnetic field, especially for application to laser-produced plasmas. We describe the essential features of the code that make it fast and robust and suitable for inclusion as a transport package in a fluid simulation. We present a few sample results that demonstrate the abilities of the code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Transport barrier and spinning blob dynamics in the tokamak edge

Abstract In this work, we investigate the dynamics of plasma blobs in the edge of magnetic confinement devices using a full-f gyrokinetic particle-in-cell code with X-point geometry. In simulations, the evolution of a seeded blob is followed as it approaches a naturally-forming zonal shear layer near the separatrix, where the blob is stabilized by a large spin induced by the self-consistent adiabatic electron response, and blob bifurcation and trapping are observed during the cross-field propagation of blobs. A new theoretical explanation in both the zonal free and zonal shear layer is constructed, where the dominant E × B spin motion is included. A theoretical condition for a transport barrier induced by the interaction between spinning blobs and the zonal shear layer is obtained, and its scaling is verified with simulations. The new theoretical framework, especially the transport barrier, is applicable to explain and predict various experimental phenomena. In particular, the transport barrier condition calculated with experimental parameters demonstrates that the blob radial transport for H mode is smaller than L mode in experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Engineered IL-18 variants with half-life extension and improved stability for cancer immunotherapy

Background The pro-inflammatory cytokine, interleukin-18 (IL-18), plays an instrumental role in bolstering anti-tumor immunity. However, the therapeutic application of IL-18 has been limited due to its susceptibility to neutralization by IL-18 binding protein (IL-18BP), short in vivo half-life, and unfavorable physicochemical properties. Methods In order to overcome the poor drug-like properties of IL-18, we installed an artificial disulfide bond, removed the native, unpaired cysteines, and fused the stabilized cytokine to an IgG Fc domain. The stability, potency, pharmacokinetic and pharmacodynamic properties as well as efficacy of disulfide-stabilized IL-18 Fc-fusion (dsIL-18-Fc) were assessed via in vitro and in vivo studies. Results The stability and mammalian host cell production yields of dsIL-18-Fc were improved, compared to the wild-type (WT) cytokine, while maintaining its biological potency and interactions with IL-18 receptor α (IL-18Rα) and IL-18BP. Recombinant fusion of the cytokine to an IgG Fc domain provided extended half-life. Notably, despite maintaining sensitivity to IL-18BP, dsIL-18-Fc was effective at activating both T and natural killer (NK) cells, and elicited a strong anti-tumor response, either as a single agent, or in conjunction with anti-programmed cell death-ligand 1 (anti-PD-L1) therapy. Conclusions We engineered IL-18 for reinforced stability, extended half-life, and improved manufacturability. The therapeutic benefit of dsIL-18-Fc, coupled with a more favorable manufacturability profile and enhanced drug-like properties, underscores the potential utility of this engineered cytokine in cancer immunotherapy.

Immunology↗
DOE OSTI2022

Collaborative Research: Explosive reconnection in relativistic magnetically-dominated plasmas

Magnetic fields can be the dominant component of astrophysical plasmas, so that the magnetic energy density might exceed even the rest-mass energy density of matter. In this extreme (and largely unexplored) regime the magnetic field controls the overall plasma evolution, dissipation, and acceleration of non-thermal particles. This plasma regime, applicable to a variety of astrophysical sources --- magnetars, pulsars and pulsar wind nebulae (PWNe), jets of Active Galactic Nuclei (AGNs) and Gamma-Ray Bursters (GRBs) --- is dramatically different from laboratory plasmas, the magnetospheres of planets, and the interplanetary plasma. Relativistic astrophysical sources then provide an unique opportunity to study the fundamental plasma physics of magnetically-dominated plasmas; a novel and quickly evolving field of theoretical research which, by investigating energy conversion and particle energization processes in plasmas, is of vital importance to the Fusion Energy Sciences DoE program.

79 ASTRONOMY AND ASTROPHYSICS↗