Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow instability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS1947

Investigations of Effects of Surface Temperature and Single Roughness Elements on Boundary-Layer Transition

The laminar boundary layer and the position of the transition point were investigated on a heated flat plate. It was found that the Reynolds number of transition decreased as the temperature of the plate is increased. It is shown from simple qualitative analytical considerations that the effect of variable viscosity in the boundary layer due to the temperature difference produces a velocity profile with an inflection point if the wall temperature is higher than the free-stream temperature. This profile is confirmed by measurements. The instability of inflection-point profiles is discussed. Studies of the flow in the wake of large, two-dimensional roughness elements are presented. It is shown that a boundary-layer can separate and reattach itself to the wall without having transition take place.

Liepmann, Hans W↗
NASA NTRS1993

A survey of low frequency waves at Jupiter: The Ulysses encounter

We report the results of a survey of low-frequency (LF) plasma waves detected during the Ulysses Jupiter flyby. In the Jovian foreshock, two predominant wave periods are detected: 10(exp 2)-s and 5-s, as measured in the spacecraft frame. The 10(exp 2)-s waves are highly nonlinear propagate at large angles to vector-B(sub 0) (typically 50 deg), are steepened, and sometimes have attached whistler packets. For the interval analyzed the 10(exp 2)-s waves had mixed right-and left-hand polarizations. We argue that these are all consistent with being right-hand magnetosonic waves in the solar wind frame. The 10(exp 2)-s waves with attached whistler are similar to cometary waves. The trailing portions are linearly polaraized and the whistler portions circularly polarized with amplitudes decreasing linearly with time. The emissions are generated by approximately 2-keV protons flowing from the Jovian bow shock/magnetosheath into the upstream region. The instability is the ion beam instability. Higher Z ions were considered as a source of the waves but have been ruled out because of the low sunward velocities needed for their resonance. The 5-s waves have delta vector-B/B(sub 0 approximately = 0.5, are compressive and are left-hand polarized in the spacecraft frame. Local generation by three different resonant interactions were considered and have been ruled out. One possibility is that these waves are whistler mode by-products of the steepened lower-frequency magnetosonic waves. Mirror mode structures were detected throughout the outbound magnetosheath passes. For these structures, the theta(sub kB) values were consistently in the range of 80 deg to 90 deg, exceptionally high values.

Tsurutani, Bruce T.↗
NASA NTRS2002

The NASA Microgravity Fluid Physics Program: Knowledge for Use on Earth and Future Space Missions

Building on over four decades of research and technology development related to the behavior of fluids in low gravity environments, the current NASA Microgravity Fluid Physics Program continues the quest for knowledge to further understand and design better fluids systems for use on earth and in space. The purpose of the Fluid Physics Program is to support the goals of NASA's Biological and Physical Research Enterprise which seeks to exploit the space environment to conduct research and to develop commercial opportunities, while building the vital knowledge base needed to enable efficient and effective systems for protecting and sustaining humans during extended space flights. There are currently five major research areas in the Microgravity Fluid Physics Program: complex fluids, multiphase flows and phase change, interfacial phenomena, biofluid mechanics, and dynamics and instabilities. Numerous investigations into these areas are being conducted in both ground-based laboratories and facilities and in the flight experiments program. Most of the future NASA-sponsored fluid physics and transport phenomena studies will be carried out on the International Space Station in the Fluids Integrated Rack, in the Microgravity Science Glovebox, in EXPRESS racks, and in other facilities provided by international partners. This paper will present an overview of the near- and long-term visions for NASA's Microgravity Fluid Physics Research Program and brief descriptions of hardware systems planned to achieve this research.

Kohl, Fred J.↗
NASA NTRS2003

The NASA Microgravity Fluid Physics Program: Research Plans for the ISS

Building on over four decades of research and technology development related to the behavior of fluids in low gravity environments, the current NASA Microgravity Fluid Physics Program continues the quest for knowledge to further understand and design better fluids systems for use on earth and in space. NASA's Biological and Physical Research Enterprise seeks to exploit the space environment to conduct research supporting human exploration of space (strategic research), research of intrinsic scientific importance and impact (fundamental research), and commercial research. The strategic research thrust will build the vital knowledge base needed to enable NASA's mission to explore the Universe and search for life. There are currently five major research areas in the Microgravity Fluid Physics Program: complex fluids, niultiphase flows and phase change, interfacial phenomena, biofluid mechanics, and dynamics and instabilities. Numerous investigations into these areas are being conducted in both ground-based laboratories and facilities and in the flight experiments program. Most of the future NASA- sponsored flight experiments in microgravity fluid physics and transport phenomena will be carried out on the International Space Station (ISS) in the Fluids Integrated Rack (FIR), in the Microgravity Science Glovebox (MSG), in EXPRESS racks, and in other facilities provided by international partners. This paper presents an overview of the near- and long-term visions for NASA's Microgravity Fluid Physics Research Program and brief descriptions of hardware systems planned to enable this research.

Kohl, Fred J.↗
NASA NTRS2006

Flow and Noise Control in High Speed and High Reynolds Number Jets Using Plasma Actuators

The idea of manipulating flow to change its characteristics is over a century old. Manipulating instabilities of a jet to increase its mixing and to reduce its radiated noise started in the 1970s. While the effort has been successful in low-speed and low Reynolds number jets, available actuators capabilities in terms of their amplitude, bandwidth, and phasing have fallen short in control of high-speed and high Reynolds number jets of practical interest. Localized arc filament plasma actuators have recently been developed and extensively used at Gas Dynamics and Turbulence Laboratory (GDTL) for control of highspeed and high Reynolds number jets. While the technique has been quite successful and is very promising, all the work up to this point had been carried out using small high subsonic and low supersonic jets from a 2.54 cm diameter nozzle exit with a Reynolds number of about a million. The preliminary work reported in this paper is a first attempt to evaluate the scalability of the technique. The power supply/plasma generator was designed and built in-house at GDTL to operate 8 actuators simultaneously over a large frequency range (0 to 200 kHz) with independent control over phase and duty cycle of each actuator. This allowed forcing the small jet at GDTL with azimuthal modes m = 0, 1, 2, 3, plus or minus 1, plus or minus 2, and plus or minus 4 over a large range of frequencies. This power supply was taken to and used, with minor modifications, at the NASA Nozzle Acoustic Test Rig (NATR). At NATR, 32 actuators were distributed around the 7.5 in. nozzle (a linear increase with nozzle exit diameter would require 60 actuators). With this arrangement only 8 actuators could operate simultaneously, thus limiting the forcing of the jet at NATR to only three azimuthal modes m = plus or minus 1, 4, and 8. Very preliminary results at NATR indicate that the trends observed in the larger NASA facility in terms of the effects of actuation frequency and azimuthal modes are similar in both small GDTL and larger NASA jets. However, the actuation authority seems to fall short in the larger jet at higher Mach numbers, resulting in decreased amplitude response compared to the small jet, which is attributed at this point to the lack of sufficient number of actuators. The preliminary results seem also to suggest that amplitude of actuation tones is similar in both the small and larger jets.

Samimy, M.↗
NASA NTRS2010

Numerical Computations of Hypersonic Boundary-Layer over Surface Irregularities

Surface irregularities such as protuberances inside a hypersonic boundary layer may lead to premature transition on the vehicle surface. Early transition in turn causes large localized surface heating that could damage the thermal protection system. Experimental measurements as well as numerical computations aimed at building a knowledge base for transition Reynolds numbers with respect to different protuberance sizes and locations have been actively pursued in recent years. This paper computationally investigates the unsteady wake development behind large isolated cylindrical roughness elements and the scaled wind-tunnel model of the trip used in a recent flight measurement during the reentry of space shuttle Discovery. An unstructured mesh, compressible flow solver based on the space-time conservation element, solution element (CESE) method is used to perform time-accurate Navier-Stokes calculations for the flow past a roughness element under several wind-tunnel conditions. For a cylindrical roughness element with a height to the boundary-layer thickness ratio from 0.8 to 2.5, the wake flow is characterized by a mushroom-shaped centerline streak and horse-shoe vortices. While time-accurate solutions converged to a steady-state for a ratio of 0.8, strong flow unsteadiness is present for a ratio of 1.3 and 2.5. Instability waves marked by distinct disturbance frequencies were found in the latter two cases. Both the centerline streak and the horse-shoe vortices become unstable downstream. The oscillatory vortices eventually reach an early breakdown stage for the largest roughness element. Spectral analyses in conjunction with the computed root mean square variations suggest that the source of the unsteadiness and instability waves in the wake region may be traced back to possible absolute instability in the front-side separation region.

Chang, Chau-Lyan↗
NASA NTRS2013

Predicting Transition from Laminar to Turbulent Flow over a Surface

A prediction of whether a point on a computer-generated surface is adjacent to laminar or turbulent flow is made using a transition prediction technique. A plurality of boundary-layer properties at the point are obtained from a steady-state solution of a fluid flow in a region adjacent to the point. A plurality of instability modes are obtained, each defined by one or more mode parameters. A vector of regressor weights is obtained for the known instability growth rates in a training dataset. For each instability mode in the plurality of instability modes, a covariance vector is determined, which is the covariance of a predicted local growth rate with the known instability growth rates. Each covariance vector is used with the vector of regressor weights to determine a predicted local growth rate at the point. Based on the predicted local growth rates, an n-factor envelope at the point is determined.

Rajnarayan, Dev↗
NASA NTRS2016

Predicting Transition from Laminar to Turbulent Flow over a Surface

A prediction of whether a point on a computer-generated surface is adjacent to laminar or turbulent flow is made using a transition prediction technique. A plurality of instability modes are obtained, each defined by one or more mode parameters. A vector of regressor weights is obtained for the known instability growth rates in a training dataset. For an instability mode in the plurality of instability modes, a covariance vector is determined. A predicted local instability growth rate at the point is determined using the covariance vector and the vector of regressor weights. Based on the predicted local instability growth rate, an n-factor envelope at the point is determined.

Rajnarayan, Dev↗
NASA NTRSDate not supplied

Global Analysis of Nonlinear Second-Mode Development in a Mach-6 Boundary Layer From High-Speed Schlieren Data

The second-mode instability on a 7◦ half-angle sharp cone at Mach 6 is analyzed using high-speed calibrated schlieren imagery at a frame rate near the expected fundamental frequency. Experiments were conducted in the NASA Langley 20-Inch Mach 6 facility at unit Reynolds number between 6.56×106 and 9.71×106 m−1. Time-resolved pixel intensity signals throughout the boundary layer are reconstructed using spatially available data in the schlieren images to recover an effective sampling rate of over 10 MHz; these are then converted to quantitative density gradients using a thin-lens-based calibration technique. A global analysis is performed on the schlieren data to investigate the nonlinear growth of the second-mode fundamental and harmonic content. Point-wise measures of the auto-bicoherence are used to identify specific triadic interactions and the locations of their highest levels of quadratic phase coupling. Significant resonance interactions between the second-mode fundamental and harmonic instabilities were found along with interactions between these and the mean flow. Bispectral mode decomposition is employed to educe the flow structures associated with these interactions. A similar analysis is performed for the power spectrum, with power spectral densities computed for each pixel’s time-series and spectral proper orthogonal decomposition employed to derive the modal structure and energy of the flow at specific frequencies. Comparisons between the bispectral quantities and second-mode power show that nonlinear interactions, particularly resonance interactions, are closely correlated with space-time modulation of disturbances during the nonlinear stage of transition.

boundary layer transition↗
NASA NTRS1979

General Theory of Aerodynamic Instability and the Mechanism of Flutter

The aerodynamic forces on an oscillating airfoil or airfoil-aileron combination of three independent degrees of freedom were determined. The problem resolves itself into the solution of certain definite integrals, which were identified as Bessel functions of the first and second kind, and of zero and first order. The theory, based on potential flow and the Kutta condition, is fundamentally equivalent to the conventional wing section theory relating to the steady case. The air forces being known, the mechanism of aerodynamic instability was analyzed. An exact solution, involving potential flow and the adoption of the Kutta condition, was derived. The solution is of a simple form and is expressed by means of an auxiliary parameter k. The flutter velocity, treated as the unknown quantity, was determined as a function of a certain ratio of the frequencies in the separate degrees of freedom for any magnitudes and combinations of the airfoil-aileron parameters.

Theodorsen, Theodore↗
NASA NTRS1991

Nonlinear symmetric instability and intraseasonal oscillations in the tropical atmosphere

Symmetric inertial instability (SII) is studied as a mechanism for stratospheric and tropospheric phenomena in the equatorial regions. The linear and nonlinear dynamics of SII in a two-layer, zonally symmetric model on an equatorial beta plane, in the presence of a basic flow with horizontal and vertical shear, with and without dissipative effects are investigated. Linear symmetric instabilities are, in accordance with previously published results, purely exponential, that is, nonoscillatory. Nonlinear SII, studied here for the first time on a planetary scale, can produce finite-amplitude oscillatory behavior, periodic or chaotic. The period of oscillations in the inviscid case depends on the initial data. In the presence of dissipative effects, all solutions tend to a limit cycle or to a strange attractor. The dominant period in this case, over a wide range of parameters and whether vertical shear is present or not, is in the intraseasonal, 20-30-day range. It appears therefore that nonlinear SII might be a contributing mechanism to low-frequency oscillations in the tropical atmosphere.

Zhao, J.-X.↗
NASA NTRS1978

Thickening of axisymmetric accretion disks and flows

A study is made to determine whether or not hot plasma flowing from the inner edge of an accretion disk around a black hole can thicken out of the disk plane with the onset of a Pringle-Rees thermal instability. The instability is caused by the density thinning caused by the sharp increase in radial infall velocity near the radius of the marginally stable circular orbit, or by abrupt variations in viscosity or Lightman-Eardly secular instabilities. An estimate of the thickening timescale is given. Various physically realistic situations involving radial steady-state flow and where significant disk thickening can occur in the region of the radius of the marginally stable circular orbit are identified. It is noted that its evolution into a large spherical cloud would require large velocities of the viscosity parameter and the amount of energy dissipated in the unstable region.

Stoeger, W. R.↗
NASA NTRS1987

An experimental evaluation of slots versus porous strips for laminar-flow applications

Detailed mean velocity and disturbance amplitude measurements were conducted in a Blasius boundary-layer flow with wall suction applied at three downstream locations. The main emphasis was a direct comparison of the growth rate of the instability wave with discrete spanwise slots versus wide porous strips. The results demonstrate that the local effects of suction through slots or very narrow porous strips have a greater beneficial effect on the stability of the boundary-layer flow relative to the suction influence of a wide porous strip. Codes which use continuous suction for the growth rates of the instability waves to determine the suction quantities for a multiple series of slots will be quite conservative in the estimation of the suction quantity. Guidelines were provided for suction-chamber design and flow rates to minimize internal oscillations which propagate into the boundary-layer flow.

Cornelius, Kenneth C.↗
NASA NTRS1988

Dynamical criterion for a marginally unstable, quasi-linear behavior in a two-layer model

A two-layer quasi-geostrophic flow forced by meridional variations in heating can be in regimes ranging from radiative equilibrium to forced geostrophic turbulence. Between these extremes is a regime where the time-mean (zonal) flow is marginally unstable. Using scaling arguments, it is concluded that such a marginally unstable state should occur when a certain parameter, measuring the strength of wave-wave interactions relative to the beta effect and advection by the thermal wind, is small. Numerical simulations support this proposal. A transition from the marginally unstable regime to a more nonlinear regime is then examined through numerical simulations with different radiative forcings. It is found that transition is not caused by secondary instability of waves in the marginally unstable regime. Instead, the time-mean flow can support a number of marginally unstable normal modes. These normal modes interact with each other, and if they are of sufficient amplitude, the flow enters a more nonlinear regime.

Ebisuzaki, W.↗
NASA NTRS1998

Experimental Study of Transitional Flow Behavior in a Simulated Low Pressure Turbine

A detailed investigation of the flow physics occurring on the suction side of a simulated Low Pressure Turbine (LPT) blade was performed. A contoured upper wall was designed to simulate the pressure distribution of an actual LPT airfoil onto a flat lower plate. The experiments were carried out for the Reynolds numbers of 35,000, 70,000, 100,000 and 250,000 with four levels of freestream turbulence ranging from 1% to 4%. For the three lower Reynolds numbers, the boundary layer on the flat plate was separated and formed a bubble. The size of laminar separation bubble was measured to be inversely proportional to the freestream turbulence levels and Reynolds numbers. However, no separation was observed for the Re = 250,000 case. The transition on a separated flow was found to proceed through the formation of turbulent spots in the free shear layer as evidenced in the intermittency profiles for Re = 35,000, 70,000 and 100,000. Spectral data show no evidence of Kelvin-Helmholtz or Tollmien-Schlichting instability waves in the free shear layer over a separation bubble (bypass transition). However, the flow visualization revealed the large vortex structures just outside of the bubble and their development to turbulent flow for Re = 50,000, which is similar to that in the free shear layer (separated-flow transition). Therefore, it is fair to say that the bypass and separated-flow transition modes coexist in the transitional flows over the separation bubble for certain conditions. Transition onset and end locations and length determined from intermittency profiles decrease as Reynolds number and freestream turbulence levels increase.

Sohn, Ki Hyeon↗
NASA NTRS2007

Experimental Study of Transitional Flow Behavior in a Simulated Low Pressure Turbine

A detailed investigation of the flow physics occurring on the suction side of a simulated Low Pressure Turbine (LPT) blade was performed. A contoured upper wall was designed to simulate the pressure distribution of an actual LPT airfoil onto a flat lower plate. The experiments were carried out for the Reynolds numbers of 35,000, 70,000, 100,000, and 250,000 with four levels of freestream turbulence ranging from 1 to 4 percent. For the three lower Reynolds numbers, the boundary layer on the flat plate was separated and formed a bubble. The size of laminar separation bubble was measured to be inversely proportional to the freestream turbulence levels and Reynolds numbers. However, no separation was observed for the Re = 250,000 case. The transition on a separated flow was found to proceed through the formation of turbulent spots in the free shear layer as evidenced in the intermittency profiles for Re = 35,000, 70,000, and 100,000. Spectral data show no evidence of Kelvin-Helmholtz of Tollmien-Schlichting instability waves in the free shear layer over a separation bubble (bypass transition). However, the flow visualization revealed the large vortex structures just outside of the bubble and their development to turbulent flow for Re = 50,000, which is similar to that in the free shear layer (separated-flow transition). Therefore, it is fair to say that the bypass and separated-flow transition modes coexist in the transition flows over the separation bubble of certain conditions. Transition onset and end locations and length determined from intermittency profiles decreased as Reynolds number and freestream turbulence levels increase.

Sohn, Ki Hyeon↗
NASA NTRS1977

Transition and laminar instability

The linear stability theory was applied to the problem of boundary layer transition in incompressible flow. The theory was put into a form suitable for three-dimensional boundary layers; both the temporal and spatial theories were examined; and a generalized Gaster relation for three-dimensional boundary layers was derived. Numerical examples include the stability characteristics of Falkner-Skan boundary layers, the accuracy of the two-dimensional Gaster relation for these boundary layers, and the magnitude and direction of the group velocity for oblique waves in the Blasius boundary layer. Available experiments which bear on the validity of stability theory and its relation to transition are reviewed and the stability theory is applied to transition prediction. The amplitude method is described in which the wide band disturbance amplitude in the boundary layer is estimated from stability theory and an interaction relation for the initial amplitude density of the most unstable frequency.

Mack, L. M.↗
NASA NTRS1985

Disturbance-wave interactions in flows with crossflow

The leading-edge region of swept wings is dominated by the crossflow instability, resulting in vortices that all rotate in the same sense. The effect of these possibly unsteady vortices on the behavior of other disturbances is examined, and a strong interaction between these and disturbances of half the dominating crossflow wavelength is predicted. According to theory, the interaction is of crossflow-crossflow type. The effect explains the anomalies found in the experimental observations of Saric and Yeates. Visually, they observe vortices at the wavelength predicted by linear theory; however, in their hot-wire measurements they find that the superharmonic dominates disturbance growth, eventually having three times the amplitude of the primary wave. In this case, the usual transition prediction methods would fail, clearly indicating the importance of studying interactions of this sort.

Reed, H. L.↗