Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “current control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

What can formal methods offer to digital flight control systems design

Formal methods research begins to produce methods which will enable mathematic modeling of the physical behavior of digital hardware and software systems. The development of these methods directly supports the NASA mission of increasing the scope and effectiveness of flight system modeling capabilities. The conventional, continuous mathematics that is used extensively in modeling flight systems is not adequate for accurate modeling of digital systems. Therefore, the current practice of digital flight control system design has not had the benefits of extensive mathematical modeling which are common in other parts of flight system engineering. Formal methods research shows that by using discrete mathematics, very accurate modeling of digital systems is possible. These discrete modeling methods will bring the traditional benefits of modeling to digital hardware and hardware design. Sound reasoning about accurate mathematical models of flight control systems can be an important part of reducing risk of unsafe flight control.

Good, Donald I.↗
NASA NTRS1978

Optimal guidance and control for investigating aircraft noise-impact reduction

A methodology for investigating the reduction of community noise impact is reported. This report is concerned with the development of two models to provide data: a guidance generator and an aircraft control generator suitable for various current and advanced types of aircraft. The guidance generator produces the commanded path information from inputs chosen by an operator from a graphic scope display of a land-use map of the terminal area. The guidance generator also produces smoothing at the junctions of straight-line paths.The aircraft control generator determines the optimal set of the available controls such that the aircraft will follow the commanded path. The solutions for the control functions are given and shown to be dependent on the class of aircraft to be considered, that is, whether the thrust vector is rotatable and whether the thrust vector affects the aerodynamic forces. For the class of aircraft possessing a rotatable thrust vector, the solution is redundant; this redundancy is removed by the additional condition that the noise inpact be minimized. Information from both the guidance generator and the aircraft control generator is used by the footprint program to construct the noise footprint.

Stewart, E. C.↗
NASA NTRS1991

A status report on a model for Benchmark active controls testing

This 'work-in-progress' paper presents a status report on an active controls flutter model which is currently in the design and fabrication phase. This model is a part of the Benchmark Models Program (BMP). The BMP is a NASA LaRC program that includes a series of models which will be used to study different aeroelastic phenomena and to validate aeroelastic methods. The objective of Benchmark Active Controls testing is to validate active control design tools. Flutter testing will be conducted with a pressure-instrumented rigid model attached to a flexible pitch and plunge mount system. Unsteady pressure distributions and transonic flutter boundaries will be measured with and without active control system engaged.

Durham, Michael H.↗
NASA NTRS1992

Loop transfer recovery for general nonminimum phase discrete time systems. II - Design

The authors consider the design of controllers for the recovery of target loop transfer function or sensitivity and complementary sensitivity functions for general nonminimum phase discrete time systems. The necessary design constraints and the available design freedom are reviewed. In view of the available freedom, possible specifications on the eigenstructure of the observer dynamic matrix are formulated. Three different types of controllers which are respectively based on prediction, current, and reduced-order estimators are considered. For each one of those controllers, three different design techniques are developed. The first one is an eigenstructure assignment scheme, while the other two are optimization-based designs. The eigenstructure assignment method yields a controller design which achieves any chosen recovery error matrix among a set of admissible recovery error matrices. On the other hand, one of the optimization-based design methods leads to a controller that achieves a recovery error matrix having the infimum H-infinity norm, while the other does the same except it achieves a recovery error matrix having the infimum H2 norm.

Chen, Ben M.↗
NASA NTRS2004

Development of a Work Control System for Propulsion Testing at Stennis Space Center (SSC)

In 1996, Stennis Space Center was given management authority for all Propulsion Testing for NASA. Over the next few years several research and development (R&D) test facilities were completed and brought up to full operation in what is known as the E-Complex Test Facility at Stennis Space Center. This paper will explain the requirements and steps taken to develop the current Test Operations' electronic work control system. The Work Control System developed includes work authorization documents such as test preparation sheets, discrepancy reports, pre-test briefing reports, and test requests.

Messer, Elizabeth A.↗
NASA NTRS1990

Prediction of forces and moments for flight vehicle control effectors. Part 2: An analysis of delta wing aerodynamic control effectiveness in ground effect

Many types of hypersonic aircraft configurations are currently being studied for feasibility of future development. Since the control of the hypersonic configurations throughout the speed range has a major impact on acceptable designs, it must be considered in the conceptual design stage. Here, an investigation of the aerodynamic control effectiveness of highly swept delta planforms operating in ground effect is presented. A vortex-lattice computer program incorporating a free wake is developed as a tool to calculate aerodynamic stability and control derivatives. Data generated using this program are compared to experimental data and to data from other vortex-lattice programs. Results show that an elevon deflection produces greater increments in C sub L and C sub M in ground effect than the same deflection produces out of ground effect and that the free wake is indeed necessary for good predictions near the ground.

Maughmer, Mark D.↗
NASA NTRS1997

Optical Design of the Developmental Cryogenic Active Telescope Testbed (DCATT)

In the summer of 1996, three Study teams developed conceptual designs and mission architectures for the Next Generation Space Telescope (NGST). Each group highlighted areas of technology development that need to be further advanced to meet the goals of the NGST mission. The most important areas for future study included: deployable structures, lightweight optics, cryogenic optics and mechanisms, passive cooling, and on-orbit closed loop wavefront sensing and control. NASA and industry are currently planning to develop a series of ground testbeds and validation flights to demonstrate many of these technologies. The Deployed Cryogenic Active Telescope Testbed (DCATT) is a system level testbed to be developed at Goddard Space Flight Center in three phases over an extended period of time. This testbed will combine an actively controlled telescope with the hardware and software elements of a closed loop wavefront sensing and control system to achieve diffraction limited imaging at 2 microns. We will present an overview of the system level requirements, a discussion of the optical design, and results of performance analyses for the Phase 1 ambient concept for DCATT,

Davila, Pam↗
NASA NTRS1989

Low power consumption current transducer

A low power consumption current transducer utilizes a saturable core reactor which includes a pair of opposed gate windings and a control winding. The control winding of the saturable reactor is arranged to receive the current to be measured. A square wave generator is connected to the gate winding of the transformer connected across the square wave generator and the secondary connected in series with the gate windings of the reactor. A full wave rectifier is connected to the gate windings and a resistor is connected across the rectifier to provide a DC voltage to cross it representative of the current flow through the control winding. A DC power supply is provided to supply power to the square wave voltage source. A diode is connected between each end of the primary winding of the transformer and one polarity of the DC power supply to commutate the reactive current resulting from the counter emf generated in the reactor back to the DC supply to eliminate potentially damaging reactive voltage spikes which would otherwise appear at the output of the square wave generator and conserve energy.

W T McLyman↗
NASA NTRS1999

International Space Station ECLSS Technical Task Agreement Summary Report

This Technical Memorandum provides a summary of current work accomplished under Technical Task Agreement (TTA) by the Marshall Space Flight Center (MSFC) regarding the International Space Station (ISS) Environmental Control and Life Support System (ECLSS). Current activities include ECLSS component design and development, computer model development, subsystem/integrated system testing, life testing, and general test support provided to the ISS program. Under ECLSS design, MSFC was responsible for the six major ECLSS functions, specifications and standard, component design and development, and was the architectural control agent for the ISS ECLSS. MSFC was responsible for ECLSS analytical model development. In-house subsystem and system level analysis and testing were conducted in support of the design process, including testing air revitalization, water reclamation and management hardware, and certain nonregenerative systems. The activities described herein were approved in task agreements between MSFC and NASA Headquarters Space Station Program Management Office and their prime contractor for the ISS, Boeing. These MSFC activities are in line to the designing, development, testing, and flight of ECLSS equipment planned by Boeing. MSFC's unique capabilities for performing integrated systems testing and analyses, and its ability to perform some tasks cheaper and faster to support ISS program needs, are the basis for the TTA activities.

Ray, C. D.↗
NASA NTRS1984

Environmental control and life support system analysis tools for the Space Station era

This paper describes the concept of a developing emulation, simulation, sizing, and technology assessment program (ESSTAP) which can be used effectively for the various functional disciplines (structures, power, ECLSS, etc.) beginning with the initial system selection and conceptual design processes and continuing on through the mission operation and growth phases of the Space Station for the purpose of minimizing overall program costs. It will discuss the basic requirements for these tools, as currently envisioned for the Environmental Control and Life Support System (ECLSS), identifying their intended and potential uses and applications, and present examples and status of several representative tools. The development and applications of a Space Station Atmospheric Revitalization Subsystem (ARS) demonstration model to be used for concent verification will also be discussed.

Blakely, R. L.↗
NASA NTRS2010

Fully Printed High-Frequency Phased-Array Antenna on Flexible Substrate

To address the issues of flexible electronics needed for surface-to-surface, surface-to-orbit, and back-to-Earth communications necessary for manned exploration of the Moon, Mars, and beyond, a room-temperature printing process has been developed to create active, phased-array antennas (PAAs) on a flexible Kapton substrate. Field effect transistors (FETs) based on carbon nanotubes (CNTs), with many unique physical properties, were successfully proven feasible for phased-array antenna systems. The carrier mobility of an individual CNT is estimated to be at least 100,000 sq cm/V(dot)s. The CNT network in solution has carrier mobility as high as 46,770 sq cm/V(dot)s, and has a large current-density carrying capacity of approx. 1,000 mA/sq cm , which corresponds to a high carrying power of over 2,000 mW/ sq cm. Such high carrier mobility, and large current carrying capacity, allows the achievement of high-speed (>100 GHz), high-power, flexible electronic circuits that can be monolithically integrated on NASA s active phasedarray antennas for various applications, such as pressurized rovers, pressurized habitats, and spacesuits, as well as for locating beacon towers for lunar surface navigation, which will likely be performed at S-band and attached to a mobile astronaut. A fully printed 2-bit 2-element phasedarray antenna (PAA) working at 5.6 GHz, incorporating the CNT FETs as phase shifters, is demonstrated. The PAA is printed out at room temperature on 100-mm thick Kapton substrate. Four CNT FETs are printed together with microstrip time delay lines to function as a 2-bit phase shifter. The FET switch exhibits a switching speed of 0.2 ns, and works well for a 5.6-GHz RF signal. The operating frequency is measured to be 5.6 GHz, versus the state-of-the-art flexible FET operating frequency of 52 MHz. The source-drain current density is measured to be over 1,000 mA/sq cm, while the conventional organic FETs, and single carbon nanotube-based FETs, are typically in the mA to mA/sq cm range. The switching voltage used is 1.8 V, while the state-of-the-art flexible FET has a gate voltage around 50 V. The gate voltage can effectively control the source-drain current with an ON-OFF ratio of over 1,000 obtained at a low Vds bias of 1.8 V. The azimuth steering angles of PAA are measured at 0deg, -14.5deg, -30deg, and 48.6deg. The measured far-field patterns agree well with simulation results. The efficiency of the 2-bit 2-element PAA is measured to be 39 percent, including the loss of transmission line, FET switch, and coupling loss of RF probes. With further optimization, the efficiency is expected to be around 50-60 percent.

Chen, Yihong↗
NASA NTRSDate not supplied

Multirotor Configuration Trades Informed by Handling Qualities for Urban Air Mobility Application

Many contemporary Advanced Air Mobility (AAM), and more specifically, urban air mobility (UAM) vehicle designers are attracted to variable rotor speed-controlled designs with multiple rotors because of the great potential for mass savings compared to more traditional, variable blade pitch-controlled vehicles. These designs are based on the assumption that the stability and control of recreation or basic utility-sized drones can be scaled to larger passenger-sized vehicles. Previous work had shown the challenges in stabilizing passenger-sized quadcopters. In this study, power constraints were made less restrictive and varied, allowing more control power. Motor parameters such as efficiency, nominal voltage and current operating point, and rise time of the rotor speed controller step response were studied. By fixing the efficiency of the motor to 95% and assuming a motor voltage to current ratio of 2.0 (previously, assumed to be 1.0), the authors were able to stabilize the quadcopter in the roll axis because this allowed the vehicle to achieve adequate rise times between 0.4 and 0.8 s. This motor optimization was extended to a hexacopter and octocopter designed to the same payload size and mission as the quadcopter. The three vehicle configurations and their motor speed controllers were compared. It was found that while hexacopter and octocopter required more mass and overall power; all three configurations had similar margins required for control. However, the hexacopter and octocopter were able to use this power margin to achieve lower rise times (i.e. the vehicle responded more quickly to pilot inputs) than the quadcopter, with the octocopter having the lowest rotor response rise time of the three vehicle configurations studied.

Multirotor↗
NASA NTRS1951

Preliminary investigation of the control of a gas-turbine engine for a helicopter / Richard P. Krebs

An analog investigation of the power plant for a gas-turbine powered helicopter indicates that currently proposed turbine-propeller engine controls are satisfactory for helicopter application. Power increases from one-half to full rated at altitudes from sea level to 15,000 feet could be made in less than 4 seconds with either the rotor or propellers absorbing the engine power.

ENGINES, CONTROL - TURBINE-PROPELLER ENGINES↗
NASA NTRS1997

Experiments in Aircraft Roll-Yaw Control using Forebody Tangential Blowing

Advantages of flight at high angles of attack include increased maneuverability and lift capabilities. These are beneficial not only for fighter aircraft, but also for future supersonic and hypersonic transport aircraft during take-off and landing. At high angles of attack the aerodynamics of the vehicle are dominated by separation, vortex shedding and possibly vortex breakdown. These phenomena severely compromise the effectiveness of conventional control surfaces. As a result, controlled flight at high angles of attack is not feasible for current aircraft configurations. Alternate means to augment the control of the vehicle at these flight regimes are therefore necessary. The present work investigates the augmentation of an aircraft flight control system by the injection of a thin sheet of air tangentially to the forebody of the vehicle. This method, known as Forebody Tangential Blowing (FTB), has been proposed as an effective means of increasing the controllability of aircraft at high angles of attack. The idea is based on the fact that a small amount of air is sufficient to change the separation lines on the forebody. As a consequence, the strength and position of the vortices are altered causing a change on the aerodynamic loads. Although a very effective actuator, forebody tangential blowing is also highly non-linear which makes its use for aircraft control very difficult. In this work, the feasibility of using FTB to control the roll-yaw motion of a wind tunnel model was demonstrated both through simulations and experimentally. The wind tunnel model used in the experiments consists of a wing-body configuration incorporating a delta wing with 70-degree sweep angle and a cone-cylinder fuselage. The model is equipped with forebody slots through which blowing is applied. There are no movable control surfaces, therefore blowing is the only form of actuation. Experiments were conducted at a nominal angle of attack of 45 degrees. A unique apparatus that constrains the model to two degrees-of-freedom, roll and yaw, was designed and built. The apparatus was used to conduct dynamic experiments which showed that the system was unstable, its natural motion divergent. A model for the unsteady aerodynamic loads was developed based on the basic physics of the flow and results from flow visualization experiments. Parameters of the aerodynamic model were identified from experimental data. The model was validated using data from dynamic experiments. The aerodynamic model completes the equations of motion of the system which were used in the design of control laws using blowing as the only actuator. The unsteady aerodynamic model was implemented as part of the real-time vehicle control system. A control strategy using asymmetric blowing was demonstrated experimentally. A discrete vortex method was developed to help understand the main physics of the flow. The method correctly captures the interactions between forebody and wing vortices. Moreover, the trends in static loads and flow structure are correctly represented. Flow visualization results revealed the vortical structure of the flow to be asymmetric even for symmetric flight conditions. The effects of blowing, and roll and yaw angles on the flow structure were determined. It is shown that superimposing symmetric and asymmetric blowing has a linearizing effect on the actuator characteristics. Transient responses of roll and yaw moments to step input blowing were characterized, and their differences were explained based on the physical mechanisms through which these loads are generated.

Pedreiro, Nelson↗
NASA NTRSDate not supplied

Designing Autonomy into Interfaces for Long-Duration Missions

As NASA develops technologies for long-duration crewed missions, we must understand how communication between ground control teams and astronauts differs from the current dynamic to adapt new concepts for long-duration mission operations. Today, ground control teams support astronauts with immediate availability to answer questions, resolve issues, and manage activities. In the near future, however, extended communication delays during long-duration missions will require astronauts to become more autonomous. As many of the responsibilities shift from the ground control teams to the astronauts on-board, the concept of operations must also change from how it functions today. With increased astronaut autonomy, software tools must be developed that enable efficient completion of mission tasks without increased mental workload. Designing software tools to facilitate crew autonomy requires development teams to know which data will enhance quick decision making while providing necessary context for situational awareness of systems being managed on-board. NASA's Autonomous Systems and Operations (ASO) team is presently developing a software interface tool, EXPRESS (EXpedite the PRocessing of Experiments for Space Station) 2.5 to enable a long-duration crew to schedule activities for and operate autonomous systems. This paper describes details of the integrated human factors approach that drove the design of the elements of the software tool, including self-managed scheduling, constraint-driven planning, autonomous system fault recovery, and recommended troubleshooting actions. Additionally, this paper will chronicle ASO modifications of the user interface after the team's first flight demonstration, how it was based on lessons learned during software development, as well as from crew feedback in order to develop the current version which will be demonstrated on ISS in 2021. In the upcoming ISS demonstration, the astronaut crew will be given scenarios for scheduling and operating autonomous system activities, including off-nominal scenarios and autonomous system recoveries. The demonstration of the EXPRESS 2.5 tool is a step towards improved levels of autonomy as our new journeys take us farther into space.

autonomy↗
NASA NTRS1992

Dynamics and control of coherent structure in turbulent jets

Current understanding of coherent structure dynamics in incompressible turbulent jets as explained by the nonlinear stability theory is reviewed, focusing on nonswirling turbulent jets. Topics addressed include hydrodynamic stability theory and coherent structures; dynamics of energy transfers among different scales of motion; nonlinear development of amplitude; development of single-frequency coherent mode; fundamental-subharmonic interaction and vortex pairing; and reversal of Reynolds stresses. Attention is also given to the effect of initial phase-difference angle between fundamental and subharmonic, conditions for resonance interaction, modulation of spreading rate by controlling coherent structure, turbulence enhancement or suppression due to excitation, 3D effects, jet noise, and swirling jets.

Mankbadi, Reda R.↗
NASA NTRS2000

Critical Questions for Space Human Factors

Traditional human factors contributions to NASA's crewed space programs have been rooted in the classic approaches to quantifying human physical and cognitive capabilities and limitations in the environment of interest, and producing recommendations and standards for the selection or design of mission equipment. Crews then evaluate the interfaces, displays, or equipment, and with the assistance of human factors experts, improvements are made as funds, time, control documentation, and weight allow. We have come a long way from the early spaceflight days, where men with the ' right stuff were the solution to operating whatever equipment was given to them. The large and diverse Shuttle astronaut corps has impacted mission designs to accommodate a wide range of human capabilities and preferences. Yet with existing long duration experience, we have seen the need to address a different set of dynamics when designing for optimal crew performance: critical equipment and mission situations degrade, and human function changes with mission environment, situation, and duration. Strategies for quantifying the critical nature of human factors requirements are being worked by NASA. Any exploration-class mission will place new responsibilities on mission designers to provide the crew with the information and resources to accomplish the mission. The current duties of a Mission Control Center to monitor system status, detect degradation or malfunction, and provide a proven solution, will need to be incorporated into on-board systems to allow the crew autonomous decision-making. The current option to resupply and replace mission systems and resources, including both vehicle equipment and human operators, will be removed, so considerations of maintenance, onboard training, and proficiency assessment are critical to providing a self-sufficient crew. As we 'move in' to the International Space Station, there are tremendous opportunities to investigate our ability to design for autonomous crews. Yet prioritizing the research that can and should be done by NASA will be based on the critical nature of the issues, and the impact of the individual research questions on mission design. The risks to crew health and safety associated with answering critical human factors issues must be properly included and communicated in order to support the Agency's decisions regarding future space programs.

Woolford, Barbara↗
NASA NTRS2008

Ground Demonstration of Synchronized Formation Rotations for Precision, Multi-Spacecraft Interferometers

This paper reports the ground demonstration of precision synchronized formation rotations with better than 6 arcmin/5 cm performance in the Formation Control Testbed (FCT). The FCT currently consists of two, five degree-of-freedom, air bearing-levitated robots. The sixth degree-of-freedom, vertical translation, is being added in November 2007. Each robot has a suite of flight-like avionics and actuators, including a star tracker, fiber-optic gyroscopes, reaction wheels, cold-gas thrusters, inter-robot communication, and on-board computers that run the Formation and Attitude Control System software.

ground demonstrations↗