Additive manufacturing of soft magnets for electrical machines—a review
Not Available
36 MATERIALS SCIENCE↗
SEARCH · Engineering Papers
Results for “conversion efficiency”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Phonon lifetimes and mode softening in cubic Cs 2 AgBiBr 6
Metal halide perovskites (MHPs) have emerged as noteworthy candidates for photovoltaic applications in recent years. Their high power-conversion efficiency is largely attributed to the structure-function relationship, which is not well understood. In this study, we examine the low-frequency phonons of the double perovskite Cs 2 AgBiBr 6 using neutron inelastic scattering. We find that the acoustic phonon lifetimes decrease from 16 to 3 ps along Γ to X, which is indicative of significant anharmonicity that contributes to the ultralow thermal conductivity. Additionally, we observe a linear temperature dependence of the square of the zone-center soft optical phonon energy, which is consistent with a weakly first-order displacive cubic-tetragonal structural phase transition. These results provide a deeper understanding of the lattice dynamics and phase transitions in MHPs as well as the effects of anharmonicity by comparison with prototypical hybrid organic-inorganic MHPs, (CH 3 NH 3 ) PbX 3 (X = Br, I).
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Scalable semitransparent prototype organic photovoltaic module with minimal resistance loss
Semi-transparent organic photovoltaic (ST-OPV) cells are regarded as an attractive solution to building-integrated solar energy harvesting. Both the power conversion efficiency (PCE) and average photopic transmission (APT) of ST-OPVs have shown substantial increases in recent years. However, less attention has been paid to the area scaling of ST-OPV cells. In this work, we investigate the scalability of ST-OPV cells from 4 mm 2 to 1 cm 2 , as well as 9 cm 2 active area prototype module. By integrating both top and bottom metal grids onto the transparent electrodes, the series resistance loss of 1 cm 2 ST-OPV cell is significantly reduced, and is comparable to that of the grid-free 4 mm 2 cell. Nine 1 cm 2 cells are then connected in a series-parallel circuit to realize a prototype ST-OPV module. A 100% fabrication yield with only 5% PCE deviation among discrete cells is achieved. The semitransparent module shows PCE = 7.2 ± 0.1% under simulated AM 1.5G illumination at 1 sun intensity, which exhibits no connection resistance loss compared to that of the individual cells. The ST-OPV module exhibits an APT = 38.1 ± 1.1%, which enables a light utilization efficiency, LUE = 2.74 ± 0.09%. Here, the method demonstrates a promising way for ST-OPV modules to scale without compromising performance.
14 SOLAR ENERGY↗
System and technoeconomic analysis of solar thermochemical hydrogen production
Hydrogen is a promising energy carrier that can be obtained from various feedstocks using renewable energy sources. Direct solar thermochemical hydrogen (STCH) production by water splitting can utilize the full spectrum of solar radiation and has the potential to achieve high solar energy conversion efficiencies. Currently STCH research areas focus on material discovery. This paper evaluates the performance of various STCH materials in the context of a system platform to assess techno-economic benefits and gaps in the path to STCH scale-up. Additionally, to analyze the hydrogen production cost, a concentrating solar thermal (CST) system is introduced as a platform for integrating STCH materials and accommodating generalized thermochemical processes. The thermochemical process is based on a two-step STCH cycle using metal oxide that consists of a high temperature step for metal oxide reduction, followed by an oxidation step for water splitting at a lower temperature. A preferred configuration is to have the high temperature step occurring in a directly irradiated solar receiver reactor. To this end, we conceptualized a receiver design and associated solar field layout and investigated STCH operational boundaries, component costs and sensitivity parameters on the $2/kgH 2 goal of hydrogen production. The study explored system-related variables and factors associated with scaling up. The CST platform allows more comprehensive studies that encompass aspects of STCH materials and systems such as cost, hydrogen productivity and replacement frequency, alongside other system components like heliostat field, tower, and potential receiver costs.
08 HYDROGEN↗
Control-inspired design and power optimization of an active mechanical motion rectifier based power takeoff for wave energy converters
Ocean waves have high energy density and are persistent and predictable. Yet, converting wave energy to a useable form remains challenging. A significant hurdle is the oscillatory nature of waves resulting in the alternating loads, which necessitate the use of rectification at some stage of the energy conversion. This research effort presents a novel design of active mechanical motion rectifier (AMMR) for the power takeoff (PTO), which provides enhanced controllability and better power performance when compared to passive mechanical motion rectifiers (MMR). Inspired by transistors used in synchronous electrical rectifiers, the proposed design uses controllable electromagnetic clutches in the mechanical transmission to allow active engagement-disengagement control; thus, rectifying the oscillatory motion into a unidirectional rotation for high energy conversion efficiency and allowing the generator in unidirectional rotation to control the bidirectional wave capture structure for maximizing the power output. A semi-analytical computational approach is developed to efficiently evaluate the optimal power achieved using the proposed AMMR-based PTO and active control. It is found that the AMMR-based PTO design yields a higher optimal power than the previous passive MMR design across the wave spectrum. The influences of generator inertia and reactive power are discussed. Furthermore, the effects of control parameters on the power output and the optimal trajectories are analyzed. Wave tank tests with the AMMR prototype demonstrated the effectiveness of AMMR based PTO design and validated the numerical analysis.
16 TIDAL AND WAVE POWER↗
Extracting energy from ocean thermal and salinity gradients to power unmanned underwater vehicles: State of the art, current limitations, and future outlook
Thermal gradient energy-generation technologies for powering unmanned underwater vehicles (UUVs) or autonomous sensing systems in the ocean are mainly in the research development phase or commercially available at a limited scale, and salinity-gradient energy-generation technologies have not been adequately researched yet. The demand for self-powered UUVs suitable for long-term deployments has been growing, and further research related to small-scale ocean gradient energy systems is needed. In this study, we conducted a comprehensive review about harvesting energy from ocean thermal or salinity gradients for powering UUVs, focusing on gliders and profiling floats. Thermal gradient energy systems for UUVs based on phase change materials (PCM) cannot provide the energy required for powering autonomous sensing systems because of the systems' low energy conversion efficiency. Besides reducing energy consumption by developing more efficient electrical-mechanical systems, enhancing the thermal conductivity of the PCMs may help address this challenge by increasing the power generation rate of the UUVs. Several other emerging technologies, such as thermoelectric generators, shape memory alloys, and small-scale thermodynamic cycle systems, have shown potential for powering UUVs, but they are still only at the laboratory testing or conceptual design phase. The most advanced power generation technologies based on salinity gradients, reverse electrodialysis and pressure-retarded osmosis, are still not economically viable for large-scale deployment, mainly because of the high cost of the components required to operate in harsh saline environments. Our feasibility evaluation showed that existing salinity gradient power generation technologies are not directly feasible for powering UUVs in the open ocean.
16 TIDAL AND WAVE POWER↗
Advancing biological processing for valorization of plastic wastes
We report the useful applications of plastics are as significant as the problems associated with their disposal. Current waste management strategies are ineffective at preventing the flow of plastics into landfills, wastewater treatment, and the environment. Despite the importance of recycling technologies, most plastics are used for consumables and are discarded after limited usage. Moreover, only certain plastics are recycled, and those that are generally yield lower value products. Discovering alternative routes for valorizing plastic wastes is essential. Emerging research involves the use of biocatalysts (i.e., enzymes and microorganisms) to produce valuable products like specialty polymers, biosurfactants, and drug precursors from these feedstocks. These bioprocesses commonly integrate physio-chemical pretreatments (to generate biologically reactive intermediates) and biological upgrading (to convert intermediates to products). Herein, publications that explore plastic deconstruction technologies and bioprocesses are reviewed with an emphasis on plastic waste valorization. Understanding how microorganisms metabolize the intermediates of plastic degradation and manage their inhibitory effects is a prerequisite for engineering bioprocesses. For these heterogeneous wastes, a paradigm shift from axenic cultivation of microorganisms to cultivation of microbial consortia may benefit conversion efficiency and stress resilience. Thus, a summary is provided for metabolic pathways and constituent enzymes required to synthesize biofuels, biomaterials, and chemicals from biologically reactive intermediates. Colossal challenges associated with the use of plastics as feedstocks for direct biological processing highlight the need for integrating physical, chemical, and biological technologies.
59 BASIC BIOLOGICAL SCIENCES↗
A review of Sb 2 Se 3 photovoltaic absorber materials and thin-film solar cells
Energy generated from environmentally friendly, cost-effective solar cells is a key aspect for developing a clean renewable-energy economy. Non-toxic and Earth-abundant materials with high absorption coefficient (>10 5 cm -1 ) and optimal bandgap (1-1.5 eV) have received great attention as photovoltaic (PV) absorber layers during the last few decades. Among them, antimony selenide (Sb 2 Se 3 ) has been a promising PV absorber, with steadily increasing power-conversion efficiency (PCE) compared to other emerging compounds. Very recent studies showed that high-quality ZnO:Al/ZnO/CdS/TiO 2 /Sb 2 Se 3 /MoSe 2 /Mo devices with PCE of 9.2% can be fabricated using cost-effective novel compounds. Considering these recent advances, this article provides an overview of the material properties of Sb2Se3 thin films and the recent progress made with Sb 2 Se 3 -based solar cells. Furthermore, analysis of Sb 2 Se 3 -based thin-film solar cells has also shown that the devices have relatively good light management due to their suitable bandgap and high absorption coefficient, whereas carrier management, i.e. collection efficiency of photo-generated carriers, needs significant improvement. Overall, this study provides background knowledge on material properties and device performance and suggests main research directions to overcome the limiting factors of solar cell performance.
14 SOLAR ENERGY↗
Comparative study on the overall energy performance between photovoltaic and Low-E insulated glass units
In this report a novel semi-transparent building integrated photovoltaic (BIPV) laminate was developed and introduced in this paper. It was produced by cutting standard mono-crystalline silicon solar cells into small strips and then making electrical connections between each strip before laminating the cells between two layers of glass. The overall energy performance and energy saving potential of the BIPV insulated glass unit (IGU) under real world conditions were identified through a side by side comparative study. Compared to the reference IGU, the BIPV IGU had lower solar heat gain coefficient (SHGC) but much higher U-factor. The average HVAC electricity saving of the BIPV IGU was about 10% relative to the reference IGU. Daylighting measurement and analysis were carried out to evaluate the trade-offs associated with the BIPV IGU between daylight, glare, and lighting energy use. The results indicated that the BIPV IGU is better than the reference IGU in reducing discomfort glare. However, if the most conservative viewpoint near the window is used for the assessment, a lower transmittance BIPV IGU is required to bring the overall discomfort levels below the perceptible level. Lastly, the net energy saving potential associated with the novel BIPV IGU was identified based on the power, thermal and daylighting performance. On average, the BIPV IGU saved 16.8% of the total electricity use of the room. Further studies and improvement on the energy conversion efficiency of solar cells, the optimal transmittance as well as the thermal properties would make this technology more energy-efficient and affordable.
14 SOLAR ENERGY↗
Evaluation of external tubular configurations for a high-temperature chloride molten salt solar receiver operating above 700°C
Next-generation concentrating solar power (CSP) tower technologies target operating temperatures exceeding 700°C to increase the thermal-to-electric conversion efficiency. Molten chloride salts are one possible alternative to current commercial molten nitrate salts to enable the higher operating temperature. This paper analyzes the predicted optical, thermal-fluids, and structural performance of traditional external tubular solar receiver configurations applied with a chloride salt heat transfer fluid (HTF) and inlet/outlet temperatures of 500°C/735°C, and considers sensitivity analysis and optimization relative to receiver sizing, tube sizing, number of panels, flow circuit configurations, and solar flux concentration under constraints on internal velocity, pressure drop, wall thickness, and required creep-fatigue lifetime. The high temperature conditions increase the significance of inelastic deformation mechanisms such as creep relative to that expected in commercial 565°C nitrate salt designs. High-temperature creep and creep-fatigue damage in the metal alloy tubes are the key factors that limit allowable solar flux concentration and achievable receiver thermal efficiency at the near-800°C wall temperature conditions. For a traditional external cylindrical receiver configuration, the design parameters and conditions capable of satisfying all constraints produced, at best, a design point receiver efficiency of 78.2%, or 80.5% when excluding receiver intercept efficiency. Variation in the optimal receiver performance relative to uncertainty in the binding maximum velocity, minimum wall thickness, and minimum lifetime constraints is presented.
14 SOLAR ENERGY↗
The heat transfer coefficient associated with a moving packed bed of silica particles flowing through parallel plates
Concentrating Solar Power (CSP) with thermal energy storage has the potential to be a renewable energy technology with long duration, inexpensive energy storage. Higher temperature operation increases the conversion efficiency and reduces the cost of energy storage. Several emerging CSP designs utilize particles as the solar receiver due to their high temperature stability and low cost. In some designs, the particles are also used as the thermal energy storage (TES) media. In either configuration, an energy transfer is required between the hot particles and the working fluid in the power cycle in a Particle-to-Fluid Heat Exchanger (PtFHX). Understanding the heat transfer between a moving packed bed and a stationary surface is critical to the successful design of a PtFHX. In this paper, a test facility is described in which a moving packed bed of silica sand with particle size 100–600 μm is introduced into the channel formed by two parallel plates, one of which is heated. The effective static thermal conductivity of the particles used for the test are separately measured over the entire range of test temperatures. The inlet and outlet bulk temperatures of the particle flow are measured as are the surface temperatures at several axial locations along the centerline of the plate. The result is the measurement of heat transfer coefficient as a function of temperature for several velocities. The uncertainty of the measurements is presented and the results are compared to model results found in the literature.
14 SOLAR ENERGY↗
Stable magnesium zinc oxide by reactive Co-Sputtering for CdTe-based solar cells
Magnesium zinc oxide (MZO) is a promising front contact material for CdTe solar cells. Due to its higher band gap than traditional CdS, MZO can reduce parasitic absorption to significantly increase short-circuit current density while also providing a benefit of conduction band offset tuning through Mg:Zn ratio optimization. MZO has been successfully implemented into CdTe devices, however its stability has been of concern. The MZO stability issue has been attributed to the presence of oxygen in the CdTe device processing ambient, leading to double-diode behavior (S-kink) in the current density-voltage curves. Here we report on MZO thin films deposited by reactive co-sputtering. The reactively co-sputtered MZO thin films have encouraging stability, show no significant variation in work function of the surface over a period of 6 months, as measured by Kelvin probe. Energy conversion efficiencies of around 16% have been achieved both with and without presence of oxygen in device processing ambients across multiple research facilities. Finally, these efficiencies should be possible to increase further by tuning of the thin film deposition and device processing parameters, especially through optimization of the back contact.
14 SOLAR ENERGY↗
Using hole injection layers for decreased metastability and higher performance in Cu(In,Ga)Se 2 devices
In this work, modifications to the buffer structure in Cu(In,Ga)Se 2 (CIGS) solar cells are examined in terms of power conversion efficiency and metastability. Varying amounts of thin hole-injecting layers are introduced at different locations in the CIGS/Zn(O,S) device structure. It is found that such layers simultaneously increase performance and decrease metastability. The most effective variant produces devices without metastability and with higher efficiency than the CdS-only controls. The most effective location for hole injection is found to be between the Zn(O,S) buffer and the transparent conductor. At this location, passivation of the CIGS surface is not a function of the hole injection layer, and thus a variety of materials with appropriate band-edge energies should achieve the same purpose.
36 MATERIALS SCIENCE↗
Semi-transparent p-type barium copper sulfide as a back contact interface layer for cadmium telluride solar cells
Optically transparent p-type materials play a critical role in transparent electronics including photovoltaic (PV) devices. P-type sulfide materials offer an alternative to oxides for PV application due to improved hole transport properties. Here, we report the solution-based synthesis of earth-abundant p-type transparent conducting barium copper sulfide (α-BaCu 4 S 3 , BCS) thin films. These films were characterized using scanning electron microscopy, X-ray diffraction, UV–Vis–NIR spectrophotometry, Raman spectroscopy, and spectroscopic ellipsometry. BCS films of ~100 nm thickness transmit >70% of visible light. We report on tests of the hole transport properties of these BCS films for cadmium telluride (CdTe) photovoltaics, finding that the BCS deposition process forms a beneficial tellurium (Te) rich surface on CdTe by selectively removing Cd from the surface. Based on our study, the BCS interface layer plays dual functions for CdTe PV devices as a hole transport material and as an etchant, enhancing the resulting device performance. We observed a significant increase in open-circuit voltage of CdTe solar cells with the BCS buffer layer. Furthermore, we discuss semitransparent CdTe solar cells with BCS as a hole transport layer and indium tin oxide as a finishing electrode. Semitransparent CdTe solar cells shows 13.3% conversion efficiency for the front side illumination and 1.2% efficiency for back side illumination, indicating high recombination of charge carriers generated close to the rear CdTe/BCS/ITO contact.
36 MATERIALS SCIENCE↗
GaAs Thermophotovoltaic Patterned Dielectric Back Contact Devices with Improved Sub-Bandgap Reflectance
We demonstrate GaAs thermophotovoltaic (TPV) devices with a patterned dielectric back contact (PDBC) architecture, featuring a dielectric spacer between the semiconductor and back metal contact over most of the back surface for high reflectance, and metal point contacts over a smaller area for electrical conduction. In the TPV application, high sub-bandgap reflectance is needed to reflect unused sub-bandgap photons to the thermal emitter to minimize energy losses in this portion of the thermal spectrum. We explore different PDBC fabrication processes with SU-8 and SiO2 dielectric spacer layers to maximize sub-bandgap reflectance while minimizing series resistance to increase TPV conversion efficiency. We successfully demonstrate GaAs SU-8 PDBC TPV devices with 2200 degrees C blackbody-weighted sub-bandgap reflectance of 94.9% and 96.5% with and without a front metal grid, respectively. This is 0.7% and 2.3% (absolute) higher than the mean sub-bandgap reflectance of 94.2% for GaAs baseline TPV devices with 100% Au back contact with front metal grid. Lower sub-bandgap reflectance in TPV devices with front grids indicates the front grid induces light scattering leading to additional parasitic absorption in the TPV device. We also show that for higher contact coverage fractions, the PDBC reflectance cannot in general be treated by a linear interpolation using simple 1D transfer matrix method modeling and should be treated instead as a diffraction grating by solving Maxwell's equations in 3D.
energy storage↗
Novel fractal-textured solar absorber surfaces for concentrated solar power
The solar absorptance of a thermal receiver surface significantly affects the photothermal conversion efficiency of concentrated solar power (CSP) plants. The development of low-cost Gen3 CSP systems calls for increasing the solar absorptance of the thermal receivers at operating temperatures above 750 °C. This study presents an innovative approach to the fractal, multiscale texturing of absorber surfaces to significantly enhance solar energy absorption for Gen3 CSP applications. The absorber surface is described in terms of its fractal parameters that are uniquely determined from surface profile measurements. The interaction of solar radiation with the fractal surface is numerically simulated by solving the governing Maxwell’s equations for electromagnetic wave propagation to investigate the effect of texturing on the absorptance of the surfaces. It is shown that absorption of the solar spectrum increases with an increase in the fractal dimension and the multiscale asperity height of the surface texturing. Here, the theoretical model is demonstrated to be in close agreement with experimental measurements of spectral absorptance of electrodeposited copper (Cu), copper mono-oxide (CuO), and copper-manganese oxide (CuMnO) surfaces that are textured to produce a range of fractal parameters by tailoring the deposition parameters. Fractal surface texturing is shown to reduce reflectance by over one order of magnitude, yielding an absorptance of greater than 0.985 for CuMnO. For the first time, the study presents a significant effective means of increasing solar absorptance and a fundamental theoretical description of the underlying physics.
14 SOLAR ENERGY↗
Electrical passivation of III-V multijunction solar cells with luminescent coupling effect
Perimeter recombination is one of the causes identified for having a nonuniform luminescent coupling effect in III-V multijunction solar cells. A potential solution could be the electrical passivation of the multijunction solar cell perimeter. To test this hypothesis, electrical passivation of InGaP/GaAs/Ge 3-junction solar cells was done by the atomic layer deposition of thin Al2O3 films. Further, perimeter passivation of a 3-junction solar cell relatively increased current collection measured at luminescent coupling and direct subcell excitation by as much as 11.4% and 29.8%, respectively. Meanwhile, the current homogeneity improved relatively by as much as 7.9% after electrical passivation. At 1-sun global standard illumination (AM 1.5G), 0.2% absolute conversion efficiency increase was achieved. Therefore, electrical passivation of fully working III-V multijunction solar cells is a non-invasive, post-treatment process that can recover losses due to surface defects caused by oxidation.
14 SOLAR ENERGY↗
Transgenic Poplar Designed for Biofuels
Members of the genus Populus (i.e., cottonwood, hybrid poplar) represent a promising source of lignocellulosic biomass for biofuels. However, one of the major factors negatively affecting poplar’s efficient conversion to biofuel is the inherent recalcitrance to enzymatic saccharification due to cell wall components such as lignin. To this effect, there have been efforts to modify gene expression to reduce biomass recalcitrance by changing cell wall properties. Furthermore, we review recent genetic modifications of poplar that led to change cell wall properties and the resulting effects on subsequent pretreatment efficacy and saccharification. Although genetic engineering’s impacts on cell wall properties are not fully predictable, recent studies have shown promising improvement in the biological conversion of transgenic poplar to biofuels.
09 BIOMASS FUELS↗