Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “coating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Assessment of variations in thermal cycle life data of thermal barrier coated rods

An analysis of thermal cycle life data for 22 thermal barrier coated (TBC) specimens was conducted. The Zr02-8Y203/NiCrAlY plasma spray coated Rene 41 rods were tested in a Mach 0.3 Jet A/air burner flame. All specimens were subjected to the same coating and subsequent test procedures in an effort to control three parametric groups; material properties, geometry and heat flux. Statistically, the data sample space had a mean of 1330 cycles with a standard deviation of 520 cycles. The data were described by normal or log-normal distributions, but other models could also apply; the sample size must be increased to clearly delineate a statistical failure model. The statistical methods were also applied to adhesive/cohesive strength data for 20 TBC discs of the same composition, with similar results. The sample space had a mean of 9 MPa with a standard deviation of 4.2 MPa.

Hendricks, R. C.↗
NASA NTRS1981

Development of molded, coated fabric joints: Fabric construction criteria for a spacesuit elbow joint

The design and fabrication of a molded, coated fabric elbow joint capable of operating reliably at 8 psi internal pressure for extended periods of flexure is considered. The overall design of the joint includes: (1) selection of heatsettable fiber of sufficient strengths; (2) choosing an optimum fabric construction; (3) a fatigue resistant; flexible coating; and (4) a molding technique. A polyester yarn of type 56 Dacron and a urethane coating system were selected. The relationships between yarn and weave parameters which lead to an optimum fabric construction for the 8 psi elbow joint are defined.

Olson, L. H.↗
NASA NTRS1981

Dry-surface coating method for visualization of separation on a bluff body

A simple and relatively accurate dry-surface coating method for visualization of the flow separation on a circular cylinder (or any bluff body) during wind tunnel tests is described. The technique consists of (1) application of a thin coating composed of an indicator and a paint carrier; (2) drying of the film; (3) conditioning of the coating with an acidic solution to ensure a suitable color reaction; (4) release into the body wake of a gas able to produce a base through chemical reaction with the solvent of the conditioning solution; and (5) color reaction according to pH.

Sadeh, W. Z.↗
NASA NTRS1981

Oxidation and hot corrosion of coated and bare oxide dispersion strengthened superalloy MA-755E

Cyclic hot corrosion and oxidation of an experimental oxide dispersion strengthened (ODS) superalloy MA-755E were conducted in a hot gas stream at Mach 0.3. The response of the ODS alloy, bare or with protective coatings, was similar to that of a conventional cast alloy, IN-792, in hot corrosion at 900 C. However, during oxidation at 1100 and 1150 C the ODS alloy differed from the cast alloy by developing a greater amount of subsurface porosity. Compared with a diffused aluminide coating, an electron beam vapor deposited NiCrAlY coating offered superior oxidation protection and decreased porosity formation. In additional testing, the tendency to form porosity was associated with the large grains of recrystallized powder metallurgy alloys but was independent of the presence of an oxide dispersion.

Glasgow, T. K.↗
NASA NTRS1983

Development of Silane Hydrolysate Binder for Thermal-Control Coatings

Technical report describes theoretical and experimental development of methyltriethoxysilane (MTES) hydrolysate binder for white, titanium dioxidepigmented thermal-control coatings often needed on satellites. New coating is tougher and more abrasion-resistant than conventional coating, S-13G, which comprises zinc oxide in hydroxyl-therminated dimethylsiloxane binder.

Patterson, W. J.↗
NASA NTRS1984

Two-Layer Glass Thermal-Control Coating

Optical properties endure high temperatures. Coating has outer scattering layer and inner high emissivity layer. Absorptivity/emissivity ratio less than 0.4. Coating withstands repeated exposure to temperatures in excess of 2,000 degrees F. Coating has industrial uses in solar-energy equipment, high temperature chemical processing systems, laboratory equipment and high temperature instrumentation.

Stewart, D. A.↗
NASA NTRS1980

Aircraft surface coatings study: Verification of selected materials

Three liquid coatings and four films that might improve and/or maintain the smoothness of transport aircraft surfaces are considered. Laboratory tests were performed on the liquid coatings (elastomeric polyurethanes) exposed to synthetic type hydraulic fluid, with and without a protective topcoat. Results were analyzed of a 14-month flight service evaluation of coatings applied to leading edges of an airline 727. Two additional airline service evaluations were initiated. Labortory tests were conducted on the films, bonded to aluminum substrate with various adhesives, to determine the best film/adhesive combinations. A cost/benefits analysis was performed and recommendations made for future work toward the application of this technology to commercial transports.

Source record↗
NASA NTRS1983

Covering solid, film cooled surfaces with a duplex thermal barrier coating

Thermal barrier coating systems were applied to hardware having passageways in the walls connecting apertures in the surface to a gas supply for film cooling. An inert gas, such as argon, is discharged through the apertures during the application of the thermal barrier coating system by plasma spraying. This flow of inert gas reduces both blocking of the holes and base metal oxidation during the coating operation.

Liebert, C. H.↗
NASA NTRS1981

Processing modifications for improved propellants - Coated oxidizers

The present investigation is concerned with a technique which makes it possible to improve greatly the performance of composite propellants by alleviating the combustion instability problem. The technique involves the coating of the oxidizer crystals (typically ammonium perchlorate) with a suitably selected chemical. For each application the chemical for the coating is chosen on the basis of a screening procedure including the employment of differential scanning calorimetry and the use of a thermogravimetric analyzer. It is particularly important that the coat chemicals have good thermochemical stability at temperatures up to the normal surface temperature of the propellant during time-independent combustion (typically 800 to 900 K). At higher temperatures, sudden degradation should occur over a vary narrow temperature range (10-20 C).

Helmy, A. K.↗
NASA NTRS1982

Polymer coating of glass microballoons levitated in a focused acoustic field

Inertial confinement fusion (ICF) glass microballoons (GMBs) levitated in a focusing radiator acoustic device can be coated with liquid materials by deploying the liquid into the levitation field with a stepped-horn atomizer. The GMB can be forced to the center of the coating liquid with a strong acoustically generated centering force. Water solutions of organic polymers, UV-curable liquid organic monomers, and paraffin waxes have been used to prepare solid coatings on the surface of GMBs using this technique.

Young, A. T.↗
NASA NTRS1984

Development of improved coating for advanced carbon-carbon components

Reaction sintered silicon nitride (RSSN) was studied as a substitute coating material on the carbon-carbon material (RCC) presently used as a heat shield on the space shuttle, and on advanced carbon-carbon (ACC), a later development. On RCC, RSSN showed potential in a 538 C (1000 F) screening test in which silicon carbide coated material exhibits its highest oxidation rate; RSSN afforded less protection to ACC because of a larger thermal expansion mismatch. Organosilicon densification and metallic silicon sealing methods were studied as means of further increasing the oxidation resistance of the coating, and some improvement was noted when these methods were employed.

Yamaki, Y. R.↗
NASA NTRS1984

Program for development of strain tolerant thermal barrier coating system

The results of thermal conductivity, thermal expansion and high cycle fatigue tests conducted on coating systems are presented. These results show that the thermal conductivity of coating system 8 at approximately 982 C (1800 F) is substantially higher than system 3 while no significant differences were observed in the thermal expansion measurements up to approximately 1316 C (2400 F). High cycle fatigue (HCF) testing, which was conducted at room temperature and several stress levels, showed both coatings to be extremely resistant to spallation in HCF.

Anderson, N. P.↗
NASA NTRS1983

Optical coating in space

A technological appraisal of the steps required to approach the goal of in-situ optical coating, cleaning and re-coating the optical elements of a remote telescope in space is reported. Emphasis is placed on the high ultraviolet throughput that a telescope using bare aluminum mirrors would offer. A preliminary design is suggested for an Orbital Coating Laboratory to answer basic technical questions.

Bunner, A. N.↗
NASA NTRS1984

Performance of thermal barrier coatings in high heat flux environments

Thermal barrier coatings were exposed to the high temperature and high heat flux produced by a 30 kW plasma torch. Analysis of the specimen heating rates indicates that the temperature drop across the thickness of the 0.038 cm ceramic layer was about 1100 C after 0.5 sec in the flame. An as-sprayed ZrO2-8%Y2O3 specimens survived 3000 of the 0.5 sec cycles with failing. Surface spalling was observed when 2.5 sec cycles were employed but this was attributed to uneven heating caused by surface roughness. This surface spalling was prevented by smoothing the surface with silicon carbide paper or by laser glazing. A coated specimen with no surface modification but which was heat treated in argon also did not surface spall. Heat treatment in air led to spalling in as early as 2 cycle from heating stresses. Failures at edges were investigated and shown to be a minor source of concern. Ceramic coatings formed from ZrO2-12%Y2O3 or ZrO2-20%Y2O3 were shown to be unsuited for use under the high heat flux conditions of this study.

Miller, R. A.↗
NASA NTRS1983

Sputtered coatings for protection of spacecraft polymers

Kapton polyimide oxidizes at significant rates (4.3x10(-24) gram/incident oxygen atom) when exposed in low Earth orbit to the ram atomic oxygen flux. Ion beam sputter deposited thin films of Al2O3 and SiO2 as well as a codeposited mixture of predominantly SiO2 with a small amount of polytetrafluoroethylene were evaluated and found to be effective in protecting Kapton from oxidation in both laboratory plasma ashing tests as well as in space on board shuttle flight STS-8. A protective film of or = 96 percent SiO2 and or = 4 percent polytetrafluoroethylene was found to be very flexible compared to the pure metal oxide coatings and resulted in mass loss rates that were 0.2 percent of that of the unprotected Kapton. The optical properties of Kapton for wavelengths investigated between 0.33 and 2.2 microns were not significantly altered by the presence of the coatings or changed by exposure of the coated Kapton to the low Earth orbital ram environment.

Banks, B. A.↗
NASA NTRS1984

Wave attenuation and mode dispersion in a waveguide coated with lossy dielectric material

The modal attenuation constants in a cylindrical waveguide coated with a lossy dielectric material are studied as functions of frequency, dielectric constant, and thickness of the dielectric layer. A dielectric material best suited for a large attenuation is suggested. Using Kirchhoff's approximation, the field attenuation in a coated waveguide which is illuminated by a normally incident plane wave is also studied. For a circular guide which has a diameter of two wavelengths and is coated with a thin lossy dielectric layer (omega sub r = 9.1 - j2.3, thickness = 3% of the radius), a 3 dB attenuation is achieved within 16 diameters.

Lee, C. S.↗
NASA NTRS1983

Contamination sensitivity of typical mirror coatings - A parametric study

Contamination budgeting for space optical systems basically starts at understanding the sensitivity of component performance, e.g. mirror reflectance, window transmittance, etc., to surface deposits. To evaluate contamination sensitivity for mirror coatings, eight types representative of those used in the vacuum ultraviolet, visible, and infrared were modeled assuming that the contaminant is uniformly deposited on the mirror surface. Parametric studies over a range of complex refractive indices combined with an examination of optical data available for several organic materials suggested division of the contaminant layer index into three categories, N = 1.5 + 0.1i, N = 1.5 + 0.5i, and N = 1.5 + 2.0i. Contaminant thickness sensitivity curves were then calculated for each of the selected mirror coatings. For comparative purposes, critical thicknesses for each type were extracted, assuming a reflectance loss of 10 percent was allowable. Critical thicknesses ranged from about 10 A to 1000 A depending on the specifics of coating design and spectral region.

Osantowski, J. F.↗