Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Transformers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Effects of Surface Orientation and Termination Plane on Glass‐to‐Crystal Transformation of Lithium Disilicate by Molecular Dynamics Simulations

Glass‐to‐crystal transformation of lithium disilicate is studied using molecular dynamics simulations using an effective partial charge potential. The structural evolution of the interface between glassy and crystalline lithium disilicate is analyzed to simulate crystallization of glass on pre‐existing crystal seeds. Besides previously used atomic number density, the distribution of Q n species (Si tetrahedra with n bridging oxygen) is shown to be an effective parameter for following this transformation quantitatively. The early stages of crystal growth are significantly affected by the orientation and termination of the surface of adjacent crystal, as indicated by calculated atomic density, partial ordering, atomic segregation, and an increase in Q 3 concentration. In particular, under‐coordinated Si within the outer crystal layer is found to be most effective in transforming the amorphous structure toward crystallinity. The increase in Q 3 in the glass close to interface region most clearly shows the initial stage of lithium disilicate crystal growth.

Sun, Wei↗
DOE OSTI2018

Theoretical and experimental evidence of conformational transformation in stereoisomers of nucleoside analogues

A theoretical and experimental characterization of N(1)-(2',3'-dihydroxypropil)thymine (DHPT), a potential prebiotic nucleoside analogue of 5-methyluridine, is performed. A proposed methodology based on a solvation method was used to study conformational transformations of the different low-energy conformers of DHPT according to time-dependent IR spectroscopy. NMR and CD spectroscopy provides additional evidence of these transformations. The conformational transformations appear to be due to solvent and DHPT interactions. This highlights the importance of experimental conditions on conformer ratio equilibrium, in particular, the interpretation of experimental conditions used for determining the stereoisomers' absolute configuration.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Recordings and Analysis of Atomic Ledge and Dislocation Movements in InGaAs to Nickelide Nanowire Phase Transformation

The formation of low resistance and self‐aligned contacts with thermally stable alloyed phases is a prerequisite for realizing reliable functionality in ultrascaled semiconductor transistors. Detailed structural analysis of the phase transformation accompanying contact alloying can facilitate contact engineering as transistor channels approach a few atoms across. Original in situ heating transmission electron microscopy studies are carried out to record and analyze the atomic scale dynamics of contact alloy formation between Ni and In 0.53 Ga 0.47 As nanowire channels. It is observed that the nickelide reacts on the In 0.53 Ga 0.47 As (111) || Ni 2 In 0.53 Ga 0.47 As (0001) interface with atomic ledge propagation along the Ni 2 In 0.53 Ga 0.47 As direction. Ledges nucleate as a train of strained single‐bilayers and propagate in‐plane as double‐bilayers that are associated with a misfit dislocation of . The atomic structure is reconstructed to explain this phase transformation that involves collective gliding of three Shockley partials in In 0.53 Ga 0.47 As lattice to cancel out shear stress and the formation of misfit dislocations to compensate the large lattice mismatch in the newly formed nickelide phase and the In 0.53 Ga 0.47 As layers. This work demonstrates the applicability of interfacial disconnection (ledge + dislocation) theory in a nanowire channel during thermally induced phase transformation that is typical in metal/III–V semiconductor reactions.

Chen, Renjie↗
DOE OSTI2023

Hydroxyl radical‐driven transformations of bisphenol A and 2,4‐dinitroanisole: Experimental and computational analysis

Abstract This study used experimental and computational analysis to investigate the advanced oxidation of bisphenol A (BPA) and 2,4‐dinitroanisole (DNAN). The pseudo first‐order reaction rate constants depended on the molar peroxide ratio and were between 0.13 and 0.28 min −1 for BPA and between 0.018 and 0.032 min −1 for DNAN. The kinetic differences appear to be due in part to the energy requirements for oxidation, which depended on the reaction mechanism but were typically lower for BPA than they were for DNAN. Density functional theory (DFT) was used to develop transformation pathways that included experimentally‐detected byproducts. The most energetically favored pathway for BPA oxidation begins with the formation of hydroxylated derivatives, while for DNAN, the most energetically favorable degradation pathway begins with the substitution of the methoxy group. Overall, these findings demonstrate the power of combining experimental and computational tools to reveal transformation mechanisms during water treatment. Practitioner Points Advanced oxidation transformations for two emerging water pollutants, bisphenol A and dinitroanisole, was investigated. The observed reaction kinetics depended on molar peroxide ratio in a manner that is in keeping with previous findings. Density functional theory‐based analysis revealed reaction energy requirements and degradation pathways.

Engineering↗
DOE OSTI2018

Application of Raman Spectroscopy for the Detection of Acetone Dissolved in Transformer Oil

The CLRS detection characteristics of acetone dissolved in transformer oil were analyzed. Raman spectral peak at 780 cm{sup –1} was used as the characteristic spectral peak for qualitative and quantitative analyses. The effect of the detection depth and the temperature was investigated in order to obtain good Raman signals. The optimal detection depth and temperature were set as 3 mm and room temperature. A quantitative model relation between concentration and the Raman peak intensity ratio I{sub 780}/I{sub 893} was constructed via the least-squares method. The results demonstrated that CLRS can quantitatively detect the concentration of acetone in transformer oil and CLRS has potential as a useful alternative for accelerating the in-situ analysis of the concentration of acetone in transformer oil.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2015

Image Reconstruction from Under sampled Fourier Data Using the Polynomial Annihilation Transform

Fourier samples are collected in a variety of applications including magnetic resonance imaging and synthetic aperture radar. The data are typically under-sampled and noisy. In recent years, l 1 regularization has received considerable attention in designing image reconstruction algorithms from under-sampled and noisy Fourier data. The underlying image is assumed to have some sparsity features, that is, some measurable features of the image have sparse representation. The reconstruction algorithm is typically designed to solve a convex optimization problem, which consists of a fidelity term penalized by one or more l 1 regularization terms. The Split Bregman Algorithm provides a fast explicit solution for the case when TV is used for the l1l1 regularization terms. Due to its numerical efficiency, it has been widely adopted for a variety of applications. A well known drawback in using TV as an l 1 regularization term is that the reconstructed image will tend to default to a piecewise constant image. This issue has been addressed in several ways. Recently, the polynomial annihilation edge detection method was used to generate a higher order sparsifying transform, and was coined the “polynomial annihilation (PA) transform.” This paper adapts the Split Bregman Algorithm for the case when the PA transform is used as the l 1 regularization term. In so doing, we achieve a more accurate image reconstruction method from under-sampled and noisy Fourier data. Our new method compares favorably to the TV Split Bregman Algorithm, as well as to the popular TGV combined with shearlet approach.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2019

Production of Airy-related beams by an Airy transform optical system

Based on the process of Huygens–Fresnel diffraction integral, we investigate theoretically the characteristics of fields generated by diffracted controllable dark-hollow beams (CDHBs) through an Airy transform optical system. It is shown that the CDHB is transformed into Airy-related beams and the dark central spot is converted into peak intensity. The effects of the incident CDHB parameters such as the mode number N, central spot width w{sub 0} and ε as well as the phase pattern parameters of Airy transform optical system on the generated beam are analyzed in detail with numerical examples.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2018

Holographic Formation of Diffraction Elements for Transformation of Light Beams in Liquid Crystal – Photopolymer Compositions

A theoretical model of holographic formation of diffractive optical elements for transformation of light beam field into Bessel-like fields in liquid crystal – photopolymer (LC–PPM) composite materials with a dyesensitizer is developed. Results of numerical modeling of kinetics ofvariation of the refractive index of a material in the process of formation with different relationships between the photopolymerization rates and diffusion processes are presented. Based on the results of numerical simulation, it is demonstrated that when the photopolarization process dominates, the diffractive element being formed is distorted. This leads to a change in the light field distribution at its output and consequently, to ineffective transformation of the reading beam. Thus, the necessity of optimizing of the recording conditions and of the prepolymeric composition to increase the transformation efficiency of light beam fields is demonstrated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2018

Room-Temperature Deformation and Martensitic Transformation of Two Co-Cr-Based Alloys

Here, deformation of two Co-Cr alloys was studied by in situ synchrotron X-ray diffraction. Both alloys show stress-induced martensite transformation, which is affected by phase stabilities and transformation strains. Crystal structure of WC in Co-20Cr-15W-10Ni is identified. Compared with other phases present, it is elastically isotropic, exhibits high strength, and can elastically withstand strains exceeding 1 pct. Texture change during phase transformation is explained based on the crystal orientation relationship between γ- and ε-phases.

36 MATERIALS SCIENCE↗
DOE OSTI2018

In Situ Local Measurement of Austenite Mechanical Stability and Transformation Behavior in Third-Generation Advanced High-Strength Steels

Austenite mechanical stability, i.e., retained austenite volume fraction (RAVF) variation with strain, and transformation behavior were investigated for two third generation advanced high strength steels (3GAHSS) under quasi-static uniaxial tension: a 1200 grade, two-phase medium Mn (10 wt%) TRIP steel, and a 980 grade, three-phase TRIP steel produced with a quenching and partitioning heat treatment. The Mn (10 wt%) TRIP steel deforms inhomogeneously via propagative instabilities (Lüders and Portevin Le Châtelier-like bands) while the 980 grade TRIP steel deforms homogenously up to necking. The dramatically different deformation behaviors of these steels required the development of a new in-situ experimental technique that couples volumetric synchrotron X-ray diffraction measurement of RAVF with surface strain measurement using stereo digital image correlation (DIC) over the beam impingement area. Measurement results with the new technique are compared with those from a more conventional approach wherein strains are measured over the entire gauge region while RAVF measurement is the same as that in the new technique. A determination is made as to the appropriateness of the different measurement techniques in measuring the transformation behaviors for steels with homogeneous and inhomogeneous deformation behaviors. Here, extension of the new in-situ technique to the measurement of austenite transformation under different deformation modes and to higher strain rates is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Coupled Small and Wide-Angle X-Ray Scattering Study of Phase Transformation Mechanisms in U-6Wt Pct Nb

The elevated temperature phase transformation kinetics of U-6wt%Nb in both wrought and cast conditions were investigated using in-situ high energy synchrotron X-ray scattering. The evolution of the phase content, γ-phase composition, and microstructure morphology was determined through the analysis of simultaneously collected wide-angle diffraction and small-angle scattering (SAXS) data. The results of the wide-angle scattering analysis, especially the phase fractions and average composition of the γ-phase, provide model parameters to enable a quantitative analysis using the SAXS data. Greater clarity regarding the kinetics of different precipitation mechanisms, namely the continuous precipitation (CP) of α-U within the γ-phase matrix and the discontinuous (DP) grain boundary precipitation of a lamellar microstructure, consisting of α-U and Nb-rich γ-phase are obtained from the coupled measurement modes. These results indicate that the CP mechanism is responsible for the initial precipitation of α-U at all temperatures considered. Near the nose in the time-temperature-transformation (TTT) diagram at ~798 K, both mechanisms are active during the early stages of phase transformation. However, the DP mechanism has an increasingly long incubation period with decreasing temperature below the TTT nose. In conclusion, the average interlamellar spacing obtained from the SAXS analysis increases with time, providing further evidence of the so-called divergent DP behavior previously observed in U-6wt%Nb alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Temperature-Dependent Thermal and Mechanical Properties of a Wire Arc Additively Manufactured Low Transformation Temperature Steel

Recent research has studied the use of low transformation temperature (LTT) martensite steel as feedstock for wire arc additive manufacturing (WAAM) and low tensile residual stresses or compressive residual stresses were detected in the printed walls. These residual stress states help to improve printed product properties such as fatigue strength and corrosion resistance. However, the thermal and mechanical properties of WAAM printed LTT martensite steel walls are largely unknown. In this work, a printed LTT martensite steel was characterized for its thermal, metallurgical, and mechanical behavior at room and elevated temperatures. The temperature-dependent specific heat capacity, thermal expansion, atomic lattice spacing, and tensile properties were measured during both heating and cooling and related to observed microstructural features and computational thermodynamics predictions. These results revealed a large hysteresis in the martensitic transformation, with a martensite start temperature of 240 °C and austenite start temperature of 680 °C. Additional thermal cycles and specimen orientation did not affect the printed specimen austenite and martensite transformations. However, it was observed that the printed metal may exhibit tempering embrittlement at about 350 °C but further studies are needed to confirm that. Further, these results suggest that a temperature control of 250 °C to 350 °C during WAAM is needed to maximize the stress reduction potential of the LTT250 martensite steel. Opportunities for future implementation of LTT martensite steels and optimization of additive manufacturing process conditions are identified.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Kinetics of Transformation of Al{sub 2}O{sub 3} to MgO·Al{sub 2}O{sub 3} Spinel Inclusions in Mg-Containing Steel

During ladle furnace refining, initial Al{sub 2}O{sub 3} inclusions generally transform into MgO·Al{sub 2}O{sub 3} spinel inclusions; these generated spinel inclusions consequently deteriorate the product quality. In this study, the transformation from Al{sub 2}O{sub 3} to MgO·Al{sub 2}O{sub 3} was investigated by immersing an Al{sub 2}O{sub 3} rod into molten steel, which was in equilibrium with both MgO and MgO·Al{sub 2}O{sub 3} spinel-saturated slag. A spinel layer, with a thickness of 4 μm, was generated on the Al{sub 2}O{sub 3} rod surface just 10 s after its immersion at 1873 K (1600 °C). The thickness of the formed spinel layer increased with the immersion period and temperature. Moreover, the MgO content of the generated spinel layer also increased with the immersion period. In this study, the chemical reaction rate at 1873 K (1600 °C) was assumed to be sufficiently high, and only diffusion was considered as a rate-controlling step for this transformation. By evaluating the activation energy, MgO diffusion in the generated spinel layer was found to be the rate-controlling step. In addition, this estimation was confirmed by observing the Mg and Al concentration gradients in the generated spinel layer. The results of this study suggest that the MgO diffusion in the spinel inclusions plays a substantial role with regard to their formation kinetics.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructures, Martensitic Transformation, and Mechanical Behavior of Rapidly Solidified Ti-Ni-Hf and Ti-Ni-Si Shape Memory Alloys

In this work, the microstructure and mechanical properties of rapidly solidified Ti{sub 50−x/2}Ni{sub 50−x/2}Hf{sub x} (x = 0, 2, 4, 6, 8, 10, and 12 at.%) and Ti{sub 50−y/2}Ni{sub 50−y/2}Si{sub y} (y = 1, 2, 3, 5, 7, and 10 at.%) shape memory alloys (SMAs) were investigated. The sequence of the phase formation and transformations in dependence on the chemical composition is established. Rapidly solidified Ti-Ni-Hf or Ti-Ni-Si SMAs are found to show relatively high yield strength and large ductility for specific Hf or Si concentrations, which is due to the gradual disappearance of the phase transformation from austenite to twinned martensite and the predominance of the phase transformation from twinned martensite to detwinned martensite during deformation as well as to the refinement of dendrites and the precipitation of brittle intermetallic compounds.

36 MATERIALS SCIENCE↗
DOE OSTI2019

The Elevated-Temperature Strength Enhancement of a Low-Cost β Titanium Alloy Through Thermomechanically-Induced Phase Transformation

The effects of temperature and thermomechanical loading on the tensile strength and hardness were studied for a rolled, low-cost metastable β titanium alloy, Ti-13Cr-1Fe-3Al (wt.%). Tensile tests were performed at temperatures between room temperature (RT) and 410°C. The results indicated that the ultimate tensile strength (UTS) decreased with increasing temperatures up to 300°C. However, the UTS was 1400 MPa at 410°C, which was approximately 150% higher than the RT UTS. It is believed that the formation of nanoscale ω and α precipitates, identified using transmission electron microscopy, hindered the dislocation motion, which resulted in the exceptionally high UTS at 410°C. However, ductility was maintained, as the elongation-to-failure (ϵ f ) was 10% at 410°C. Dynamic mechanical analysis suggested that phase transformations occurred between 370°C-475°C. To evaluate the effect of the phase transformations on the hardness, the as-received material was heat treated at 400°C, 450°C, and 500°C for 2 h, which resulted in hardness values of approximately 340 Hv, 380 Hv, and 470 Hv, respectively. However, the greatest hardness value (500 Hv) was exhibited by the as-received material after it was tensile tested at 410°C. This suggested that both temperature and loading history affected the phase transformations. Finally, as all the samples exhibited a ductile fracture mode, this work indicates that it is possible to maintain both high strength and adequate ϵ f for Ti-13Cr-1Fe-3Al (wt.%).

36 MATERIALS SCIENCE↗
DOE OSTI2015

Shape transformation of bimetallic Au–Pd core–shell nanocubes to multilayered Au–Pd–Au core–shell hexagonal platelets

Transformation of metallic or bimetallic (BM) nanoparticles (NPs) from one shape to another desired shape is of importance to nanoscience and nanotechnology, where new morphologies of NPs lead to enhancement of their exploitable properties. In this report, we present the shape transformation of Au octahedral NPs to Au–Pd core–shell nanocubes, followed by their transformation to nanostars and finally to multilayered Au–Pd–Au core–shell hexagonal platelets in the presence of T30 DNA. The weaker binding affinity of T30 DNA directs the growth to favor the formation of lower energy {111} facets, changing the morphology from nanocubes to nanostar. The nanostars, exhibiting unusual intermediate morphologies, are comprised two sets of shell layers and have Au core, Pd intermediate shell, and Au outer shell. Similarly, the hexagonal platelets, which also have Au core and inner Pd shell, are encased in an external gold shell. As a result, the formation of multilayered Au–Pd–Au core–shell hexagonal platelets from Au–Pd core–shell nanocubes via the multilayered nanostars is monitored using scanning/transmission electron microscopy analysis.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Phase Composition and Phase Transformation of Additively Manufactured Nickel Alloy 718 AM Bench Artifacts

Additive manufacturing (AM) technologies offer unprecedented design flexibility but are limited by a lack of understanding of the material microstructure formed under their extreme and transient processing conditions and its subsequent transformation during post-build processing. As part of the 2022 AM Bench Challenge, sponsored by the National Institute of Standards and Technology, this study focuses on the phase composition and phase evolution of AM nickel alloy 718, a nickel-based superalloy, to provide benchmark data essential for the validation of computational models for microstructural predictions. Here, we employed high-energy synchrotron X-ray diffraction, in situ synchrotron X-ray scattering, as well as high-resolution transmission electron microscopy for our analyses. The study uncovers critical aspects of the microstructure in its as-built state, its transformation during homogenization, and its phase evolution during subsequent aging heat treatment. Specifically, we identified secondary phases, monitored the dissolution and coarsening of microstructural elements, and observed the formation and stability of γ ’ and γ ” phases. The results provide the rigorous benchmark data required to understand the atomic and microstructural transformations of AM nickel alloy 718, thereby enhancing the reliability and applicability of AM models for predicting phase evolution and mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

He bubble-induced phase transformation of W grain boundaries revealed by accelerated molecular dynamics

The growth of He bubbles and the resulting impact on the microstructural evolution of W are of paramount importance to the plasma-facing materials community due to the application of W in Tokamak fusion reactors. Using accelerated molecular dynamics (AMD) techniques, we outline the structural evolution of grain boundaries (GBs) caused by growing He bubbles. It is discovered that when an alternative, low energy, high density GB structure or phase is available, He bubbles can induce a progressive phase transformation of the GB to the higher density phase by the continual nucleation of W Frenkel pairs. Here, we find that the resulting W self-interstitials migrate to sites at the GB which are structurally related to the higher density phase, leading to the transformation. We discuss the implications of this progressive microstructural evolution on the growing He bubble and consider in general how He bubbles will impact the structural evolution of an arbitrary W GB. These findings of GB phase transformation are predicted to impact other damage events in W such as recrystallization, GB migration and defect segregation which must take these findings into account in order to accurately simulate a realistic W microstructure and hence extract experimentally meaningful data.

36 MATERIALS SCIENCE↗