Internal grid for release of brazing retorts
Wire grid permits retorts to be opened more quickly after brazing. Grid also aids purging and evacuation, better control of vacuum in part area, and reduces thermocouple damage.
Beuyukian, C. S.↗
SEARCH · Engineering Papers
Results for “THERMOCOUPLES”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Wind-tunnel investigation of aerodynamic performance, steady amd vibratory loads, surface temperatures, and acoustic characteristics of a large-scale twin-engine upper-surface blown jet-flap configuration
Static and wind-on tests were conducted to determine the aerodynamic characteristics of and the effects of jet impingement on the wing of a large scale upper surface blown configuration powered with an actual turbine engine. The wing and flaps were instrumented with experimental dual-sensing transducer units consisting of a fluctuating pressure gage, a vibratory accelerometer, and a surface mounted alumel thermocouple. Noise directivity and spectral content measurements were obtained for various flap configurations and various engine thrust settings to provide baseline noise data for other upper surface blown configurations.
Source record↗
Conceptual design for spacelab pool boiling experiment
A pool boiling heat transfer experiment to be incorporated with a larger two-phase flow experiment on Spacelab was designed to confirm (or alter) the results of earth-normal gravity experiments which indicate that the hydrodynamic peak and minimum pool boiling heat fluxes vanish at very low gravity. Twelve small sealed test cells containing water, methanol or Freon 113 and cylindrical heaters of various sizes are to be built. Each cell will be subjected to one or more 45 sec tests in which the surface heat flux on the heaters is increased linearly until the surface temperature reaches a limiting value of 500 C. The entire boiling process will be photographed in slow-motion. Boiling curves will be constructed from thermocouple and electric input data, for comparison with the motion picture records. The conduct of the experiment will require no more than a few hours of operator time.
Lienhard, J. H.↗
A low cost, portable instrument for measuring emittance
A low cost, portable instrument has been developed with which emittance can be measured by comparison to a standard. A reflector collects infra-red radiation from a heated sample onto a low mass, black detector and the temperature rise of the black detector is measured with a thermocouple and meter. Graphical examples are presented for determination of emittance from measurements made on a sample at any known temperature.
Mcdonald, G.↗
Lamination residual strains and stresses in hybrid laminates
An investigation is conducted of the effects of hybridization on the magnitude of lamination residual stresses. Eight-ply graphite/Kevlar 49/epoxy and graphite/S-glass/epoxy laminates were studied. The same matrix resin was selected for all basic materials to ensure compatibility and uniform curing of the various plies. The specimens, with inserted strain gages and thermocouples, were subjected to curing and postcuring cycles in an autoclave. Subsequently, the specimens were subjected to a thermal cycle from room temperature to 444 K and down to room temperature. It was found that hydridizing reduces apparently residual strains and stresses in the graphite plies. However, these strains were not affected much by the type and degree of hybridization.
Daniel, I. M.↗
Instrumentation techniques for studying heterogeneous combustion
Velocity measurements in flames and the simultaneous measurement of droplet size and velocity with the aid of laser anemometry are considered along with methods of particle size measurement and techniques based on laser Raman spectroscopy. Attention is given to high-speed photography and holography, computer compensated thermocouples, and the determination of turbulence characteristics. The employment of suction probes is also discussed, taking into account sampling methods, the effects of temperature change in sampling probes on particle formation, and the chemical analysis of samples.
Chigier, N. A.↗
Anode power in quasisteady magnetoplasmadynamic accelerators
Anode heat flux in a quasi-steady MPD accelerator has been measured directly and locally by thermocouples attached to the inside surface of a shell anode. These measurements show that over a range of arc current from 5.5 to 44 kA, and argon mass flow from 1 to 48 g/s, the fraction of the total arc power deposited in the anode decreases from 50% at 200 kW to 10% at 20 MW. A theoretical model of the anode heat transfer asserts that energy exchange between electrons and heavy particles in the plasma near the anode occurs over distances greater than the anode sheath thickness, and hence the usual anode fall voltage, electron temperature, and work function contributions to the anode heat flux are supplemented by a contribution from the interelectrode potential. Calculations of anode heat flux using the measured current density, plasma potential, and electron temperature in the plasma adjacent to the anode agree with the direct measurements and indicate that the decrease in anode power fraction at higher arc powers can be attributed to the smaller mean free paths in the interelectrode plasma.
Saber, A. J.↗
Correlation of predicted and measured thermal stresses on a truss-type aircraft structure
A test structure representing a portion of a hypersonic vehicle was instrumented with strain gages and thermocouples. This test structure was then subjected to laboratory heating representative of supersonic and hypersonic flight conditions. A finite element computer model of this structure was developed using several types of elements with the NASA structural analysis (NASTRAN) computer program. Temperature inputs from the test were used to generate predicted model thermal stresses and these were correlated with the test measurements.
Jenkins, J. M.↗
The 737 aircraft flammability testing
The FAA requested approximately 20 component and full-scale tests in a 737 fuselage to provide validation data or indicate changes that need to be made to a fire math model (Dayton Aircraft Cabin Fire Model) developed for the FAA. Some preliminary tests were conducted to evaluate the adequacy of planned instrumentation. The objectives of the program were met in that it was verified that propagation of a fire could be determined from the sequential response of thermocouples located on a test specimen(such as a seat), and continuous weighing of the specimen during the test was accomplished. Two differenct techniques for measuring smoke density were found to be comparable.
Bricker, R. W.↗
Multistack nickel-hydrogen units
A typical 625 Inconel pressure vessel, equipped with four thermocouples, has voltage taps not only for the cell, but for each of the several packs inside the container. In a two-stack design, a weld ring is used to separate the packs which, joined together, form one solid group. In the four-stack design, stacks are separated mechanically with about half inch Plexiglas and are connected through the center. Electrolytes are forced out by vacuum. The two stack design is intended for 500 psi and was pressure tested up to 1,000. The problem of electrolyte shorts is discussed and possible solutions for its correction are given.
Smith, J.↗
Development of procedures for calculating stiffness and damping of elastomers in engineering applications. Part 5: Elastomer performance limits and the design and test of an elastomer damper
Tests were performed on elastomer specimens of the material polybutadiene to determine the performance limitations imposed by strain, temperature, and frequency. Three specimens were tested: a shear specimen, a compression specimen, and a second compression specimen in which thermocouples were embedded in the elastomer buttons. Stiffness and damping were determined from all tests, and internal temperatures were recorded for the instrumented compression specimen. Measured results are presented together with comparisons between predictions of a thermo-viscoelastic analysis and the measured results. Dampers of polybutadiene and Viton were designed, built, and tested. Vibration measurements were made and sensitivity of vibration to change in unbalance was also determined. Values for log decrement were extracted from the synchronous response curves. Comparisons were made between measured sensitivity to unbalance and log decrement and predicted values for these quantities.
Tecza, J. A.↗
Supersonic burning in separated flow regions
Activities reported include: (1) the construction of a thermocouple with a protective coating or sheath for obtaining reliable temperature measurements of gases in the base region; (2) the construction of a multiposition back step plate for trough tests for step sizes 0.63 cm and 0.25 cm; and (3) flow pattern studies with the 6.35 cm trough to determine the complex flow resulting when a shear layer reattaches in a corner. Reliable ignition and stable burning were achieved at Mach = 2 for the 0.63 cm trough. Photographs of side wall oil streaks for M=2 flow, and some static and pitot pressure results at M = 3 are included.
Zumwalt, G. W.↗
Temperature Measurement
The design, installation, checkout, calibration, and operation of a temperature measuring system to be used during tests of a liquid monopropellant rocket engine are discussed. Appendixes include: (1) temperature measurement system elemental uncertainties, and (2) tables and equations for use with thermocouples and resistance thermometers. Design guidelines are given for the critical components of each portion of the system to provide an optimum temperature measurement system which meets the performance criteria specified.
Source record↗
Large-scale pool fire test recommendations
The important aspects of external pool fires are outlined. The research objectives are: (1) determine heat flux to surfaces as a function of pool size (convective and radiative heat flux); (2) obtain information that can be compared with theoretical models for radiative flux in the near field; and (3) predict radiative heat flux for arbitrary pool size. The measurements and instrumentation (calorimeters and thermocouples) used for pool fires are outlined.
Bankston, C. P.↗
NaOH-based high temperature heat-of-fusion thermal energy storage device
A material called Thermkeep, developed as a low-cost method for the storage of thermal energy for solar electric power generating systems is discussed. The storage device consists of an insulated cylinder containing Thermkeep in which coiled tubular heat exchangers are immersed. A one-tenth scale model of the design contains 25 heat-exchanger tubes and 1500 kg of Thermkeep. Its instrumentation includes thermocouples to measure internal Thermkeep temperatures, vessel surface, heated shroud surface, and pressure gauges to indicate heat-exchanger pressure drops. The test-circuit design is presented and experimental results are discussed.
Cohen, B. M.↗
The application of solar thermoelectric generators in near-sun missions
Future planetary near-sun missions, such as those studied for low-altitude Mercury Orbiters, introduce challenges in the selection of appropriate power sources. Study results have shown that conventional silicon solar array technology is not adequate to produce power because of expected temperatures which range from -90 C to +285 C in about 40 to 50 minutes for 16 sun eclipses/day. The solar thermoelectric generator (STG), which requires relatively high temperatures, is being considered as a replacement power source. The complete STG consists of a solar concentrator and multiple thermopiles, each containing numerous thermocouples and thermal insulation material. Articulation of the STG design configurations is required at 0.45 AU to acquire maximum incident radiation and at 0.3 AU to reduce the higher incident radiation. STG thermal input to the spacecraft as it orbits Mercury (including sun eclipses) is insignificant.
Raag, V.↗
Analytical predictions of selenide RTG power degradation
A mathematical model for the performance and degradation analysis of an RTG using the newly developed selenide thermoelectric materials has been developed at JPL. The computerized model is quite comprehensive and enables the accurate detailing of the electrical and thermal effects that take place within the thermocouple under any desired set of operation conditions, including heat input, ambient temperature and load conditions. The paper discusses the logic flow of the computer model and presents the time and temperature dependent results for various degradation mechanisms and rates as they have been established to date.
Noon, E. L.↗
Measurement in multiphase reacting flows
A survey is presented of diagnostic techniques and measurements made in multiphase reacting flows. The special problems encountered by the presence of liquid droplets, soot and solid particles in high temperature chemically reacting turbulent environments are outlined. The principal measurement techniques that have been tested in spray flames are spark photography, laser anemometry, thermocouples and suction probes. Spark photography provides measurement of drop size, drop size distribution, drop velocity, and angle of flight. Photographs are analysed automatically by image analysers. Photographic techniques are reliable, inexpensive and proved. Laser anemometers have been developed for simultaneous measurement of velocity and size of individual particles in sprays under conditions of vaporization and combustion. Particle/gas velocity differentials, particle Reynolds numbers, local drag coefficients and direct measurement of vaporization rates can be made by laser anemometry. Gas temperature in sprays is determined by direct in situ measurement of time constants immediately prior to measurement with compensation and signal analysis by micro-processors. Gas concentration is measured by suction probes and gas phase chromatography. Measurements of particle size, particle velocity, gas temperature, and gas concentration made in airblast and pressure atomised liquid spray flames are presented.
Chigier, N. A.↗