Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “THERMAL FRACTURES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Ice-covered water volcanism on Ganymede

Eruption of liquid H2O magmas along extensional fractures and graben-bounding normal faults may have played a critical role in the development of Ganymede's grooved terrain. The resurfacing potential of a water magma is dependent on a variety of factors, including the areal extent of the source region, the rate of discharge, the thickness of the flow, and the time that it takes the flow to completely freeze to its base. In this paper the thermal evolution of such a flow is considered in detail. The minimum unfrozen lifetime of a 5-m flow is approximately 12.5 days while a 10-m flow would survive for at least 50 days. Heating resulting from frictional head loss could reasonably extend these lifetimes by 50 percent or more. With a discharge rate of the order of 1-10 cu km/d, an individual volcanic water flow could flood an area of about 10,000 sq km before freezing. As the flow solidifies, its volume will increase, thus lifting and arching its protective ice cover. Extensional fractures may then develop in the ice subparallel to the graben walls. These fractures could result in grooves directly, given a sufficiently thick (1 km) flow, or they may simply act to concentrate various tectonic forces that could initiate groove-producing faults.

Allison, M. Lee↗

Completion Effects on Diagnosing Multistage Facture Treatments with Distributed Temperature Sensing

Summary Distributed temperature sensing (DTS) is a valuable tool to diagnose multistage hydraulic fracture treatments. When a stage interval is shut in, the clusters that take more fluid during pumping warm up more slowly. Therefore, the fluid volume injected into each cluster can be quantitatively interpreted by numerical inversion of the warm-back temperature behavior. This general concept assumes that the different warm-back behavior is controlled by only the injected fluid volume; however, recent observations of DTS data indicate that completion configurations significantly influence the warm-back behavior. This paper investigates the completion effects on the DTS interpretation. In ideal conditions, when a stage is fractured, the upstream stage intervals should show an almost uniform temperature that is close to the injected fluid temperature. This is due to the high fluid velocity of injected fluid in the wellbore, and the upstream intervals have not been perforated (noncommunicating intervals), so the only heat transfer is heat conduction between the wellbore fluid and the surrounding reservoir. But the field DTS data show considerably irregular variations in temperature along the upstream stage intervals. These variations are caused by the completion effects. The nonuniform temperature profile is caused by different heat transfer behavior induced by completion hardware along the production casing string, such as joints, clamps, and blast protectors, and by the sensing cable location in the cement, as well as the cement quality. Because the varying heat transfer behavior impacts the warm-back behavior as well as the temperature profile, the completion effects need to be considered in DTS interpretation. A method of DTS interpretation considering the completion effects to diagnose multistage fracture treatments was developed. Because the heat transfer between a wellbore and a reservoir depends on the overall heat transfer coefficient describing heat conduction through the completion in a forward model, this parameter needs to be tuned all along the wellbore. To calibrate the completion effect, the temperature inversion is conducted using the temperature measured at a stage interval that is upstream of a stage interval currently being treated. Because the interpreted stage interval is not perforated at that time, the thermal behavior at the noncommunicating interval is governed by only the heat conduction through the completion environment. Once the effective values of the overall heat transfer coefficient are estimated along the interpreted stage interval, they can be assumed to be constant physical parameters. Then, the fluid volume distribution is interpreted by using the effective overall heat transfer coefficient profile along each interval. This study provides a field application of the developed interpretation method. The new interpretation method provides more accurate diagnosis of fracture treatments by DTS interpretation.

Engineering↗

Investigation of Current Parameters and Size Effects on Mechanical Properties During Pulsed Electrically Assisted Uniaxial Tension in T2 Red Copper Sheets

It has been found that the electrically assisted (EA) forming can alleviate size effects due to the electroplastic effect. Size effects exist in the manufacture of tiny workpieces and severely affect material performances because the grain boundary hardening effect and strong anisotropy of the mechanical properties of the grains will lead to a strong variation in the forming properties of the sheet. In order to investigate the influences of current parameters and size effects on mechanical properties in EA forming, EA uniaxial tension tests with varying grain size and thickness were conducted on T2 red copper sheets. The small temperature rise shows the thermal effect is slight; the flow stress decreases with the increase in pulse frequency, pulse duty ratio and current density; the finer grains still result in higher strength and better plasticity; Moreover, the fluctuations of tensile strength, maximum uniform strain and fracture strain decrease with the increase in the ratio of thickness to grain size (N) at constant current density, which means pulsed current can weaken size effects.

36 MATERIALS SCIENCE↗

Mechanical Properties and Durability of "Waterless Concrete"

Waterless concrete consists of molten elementary sulfur and aggregate. The aggregates in lunar environment will be lunar rocks and soil. Sulfur is present on the Moon in Troilite soil (FeS) and by oxidation soil iron and sulfur can be produced. Iron can be used to reinforce the sulfur concrete. Sulfur concrete specimens were cycled between liquid nitrogen (approximately 191 C) and room temperature (approximately 21 C) to simulate exposure to a lunar environment. Cycled and control specimens were subsequently tested in compression at room temperatures (approximately 21 C) and approximately 101 C. Test results showed that due to temperature cycling, compressive strength of cycled specimens was 20% of those non-cycled. Microscopic examination of the fracture surfaces from the cycled samples showed clear de-bonding of the sulfur from the aggregate material whereas it was seen well bonded in those non-cycled. This reduction in strength can be attributed to the large differences in thermal coefficients of expansion of the materials constituting the concrete which promoted cracking. Similar sulfur concrete mixtures were strengthened with short and long glass fibers. The glass fibers from lunar regolith simulant was melted in a 25 cc Pt-Rh crucible in a Sybron Thermoline high temperature MoSi2 furnace at melting temperatures of 1450 to 1600 C for times of 30 min to 1 hour. Glass fibers were cast from the melt into graphite crucibles and were annealed for a couple of hours at 600 C. Glass fibers and small rods were pulled from the melt. The glass melt wets the ceramic rod and long continuous glass fibers were easily hand drawn. The glass fibers were immediately coated with a protective polymer to maintain the mechanical strength. The glass fibers were used to reinforce sulfur concrete plated to improve the flexural strength of the sulfur concrete. Prisms beams strengthened with glass fibers were tested in 4-point bending test. Beams strengthened with glass fiber showed to exhibit an increase in the flexura strength by as much as 45%.

Toutanji, Houssam↗

Microstructure and magnetic properties of Ni{sub 50}Mn{sub 37}Sn{sub 13} Heusler alloy ribbons

The Heusler alloy Ni{sub 50}Mn{sub 37}Sn{sub 13} was successfully produced as ribbon flakes of thickness around 7-10 {mu}m melt spinning. Fracture cross section micrographs in the ribbon show the formation of a microcrystalline columnarlike microstructure, with their longer axes perpendicular to the ribbon plane. Phase transition temperatures of the martensite-austenite transformation were found to be M{sub S}=218 K, M{sub f}=207 K, A{sub S}=224 K, and A{sub f}=232 K; the thermal hysteresis of the transformation is 15 K. Ferromagnetic L2{sub 1} bcc austenite phase shows a Curie point of 313 K, with cell parameter a=0.5971(5) nm at 298 K, transforming into a modulated 7M orthorhombic martensite with a=0.6121(7) nm, b=0.6058(8) nm, and c=0.5660(2) nm, at 150 K.

36 MATERIALS SCIENCE↗

A Laboratory Assessment and Optimization of Nanoparticle-Stabilized CO2 Foams for Hydraulic Fracturing Applications

In this research, we have conducted a comprehensive assessment and optimization of aqueous CO2 foams for fracturing applications. The performance of CO2 foams is evaluated using three major matrices: foam stability, foam apparent viscosity, and leakoff. The response of these performance matrices to different internal factors and external conditions is evaluated. These factors and conditions include foam quality, nanoparticle concentration, salinity, shear rate, surfactant type and concentration, polymer concentration, and temperature. Before foam generation, the colloidal stability of the nanosilica dispersion is evaluated at different types of electrolytes and under high temperatures. With a good salinity resistance and thermal stability, the nanosilica is then used for the entire set of foam generation experiments. The foam configuration with optimized parameters is used for the leakoff test, which serves as a supplementary section to further demonstrate the advantages of the proposed foam system. Then the final commercialization section provides a general view of what should be considered to commercialize the research results. In general, it is found that the aqueous CO2 foam system has demonstrated a good potential to be used as a fracturing fluid. The design of the foam system needs to consider formations properties and formation fluid properties etc. to realize the optimal performance of the system on a laboratory scale.

02 PETROLEUM↗

Two Stages of Impact Fracture of Polycrystalline ZnS and ZnSe Compounds

Mechanoluminescence (ML) in ductile solids is caused by the motion of charged dislocations in the deformable material. Interatomic bond ruptures followed by electronic structure reconfiguration are the main source of ML in brittle bodies. We studied ML in ceramics composed of mixed ionic/covalent ZnS and ZnSe compounds, which are generated during impact loading higher than the limit deformation. Depending on synthesis method and thermal treatment, the resulting ceramics had different size and geometry of grains and intergrain boundary structure, which presumably may have a significant effect on the dislocation glide. In both materials, the time sweeps of ML pulses have two well-resolved peaks. The position of the peaks along the time axis is substantially dependent on the size of ceramic-forming grains and, to a smaller extent, on the barrier properties of intergrain boundaries. The first peak is associated with plastic deformation preceding disintegration of the crystal structure. The second peak emerges upon crack nucleation as interatomic bonds are ruptured and the material is undergoing local deformation in tips of propagating cracks. The distributions of ML pulse amplitudes (the dependences between the number of pulses and their amplitude) calculated for both peaks individually follow the power law, which demonstrates that the electronic processes having different excitation mechanisms (dislocation motion vs bond rupture) are correlated.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NuScale Pressure and Temperature Limits Methodology Using Finite Element Analysis

Per 10 CFR 50 Appendix G, the pressure-temperature (P-T) limits curves and minimum temperature must be established to provide adequate margins for ferritic pressure-retaining components of the reactor coolant pressure boundary; this is to protect against brittle failure during any normal operating conditions, including anticipated operational occurrences and system hydrostatic tests, to which the pressure boundary may be subjected over its service lifetime. Specifically, ASME Code Section XI Appendix G procedures must be used for P-T limits calculation considering the pressure and temperature at various operating transient conditions. However, the elastic fracture mechanics solutions in Section XI are only suitable for cylindrical reactor pressure vessel (RPV) beltline without geometric discontinuities. Hence, these solutions are not suitable for postulated flaws near the core support blocks attached to the NuScale RPV inside surface, which is part of the beltline. As a result, NuScale has used finite element analysis to calculate thermal stress and stress intensity factor for the postulated flaws. The solutions using finite-element analysis have been validated using the formulations for straight cylinders for both axial and circumferential flaws. In addition, special considerations are given to the RPV beltline nil-ductility transition temperature (RTNDT) due to neutron irradiation occurring at lower temperatures than conventional plants. The paper summarizes the methodology and finite-element models used to develop P-T limits curves for NuScale RPV at the end of its 60-year design life.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Engineering Stress in Perovskite Solar Cells to Improve Stability

We report on an overlooked factor affecting stability: the residual stresses in perovskite films, which are tensile and can exceed 50 MPa in magnitude, a value high enough to deform copper. These stresses provide a significant driving force for fracture. Films are demonstrated to be more unstable under tensile stress—and conversely more stable under compressive stress— when exposed to heat or humidity. Increasing the formation temperature of perovskite films directly correlates with larger residual stresses, a result of the high thermal expansion coefficient of perovskites. Specifically, this tensile stress forms upon cooling to room temperature, as the substrate constrains the perovskite from shrinking. No evidence of stress relaxation is observed, with the purely elastic film stress attributed to the thermal expansion mismatch between the perovskite and substrate. Additionally, the authors demonstrate that using a bath conversion method to form the perovskite film at room temperature leads to low stress values that are unaffected by further annealing, indicating complete perovskite formation prior to annealing. It is concluded that reducing the film stress is a novel approach for improving perovskite stability, which can be accomplished by lower formation temperatures, flexible substrates with high thermal expansion coefficients, and externally applied compressive stress after fabrication.

36 MATERIALS SCIENCE↗

Insights into the physical and chemical properties of a cement-polymer composite developed for geothermal wellbore applications

To isolate injection and production zones from overlying formations and aquifers during geothermal operations, cement is placed in the annulus between well casing and formations. Wellbore cement can fracture due to chemical and physical stress. A polymer-cement (composite) with self-healing properties, stable at high temperatures, was recently developed by our group. Here we present data on the elemental distribution, mineral composition, internal microstructure, and tensile elasticity of this composite and how it compares to cement without polymer (control cement). Entrapped air porosity was similar between control cement (0.44% by volume) and composite (0.22% by volume). Total voids increased with polymer content in the cement (10% and 25% composite), and polymer was found to fill most of these voids. Polymer appears to act as a (cement hydration) retarder increasing the amount of unhydrated silicate minerals in the matrix. Tensile elasticity was improved for composites as compared to control cement, suggesting that the composite materials perform better under mechanical stress. Density-functional calculations reproduce the drop in Young’s modulus by about 60% observed experimentally when polymer is added to the cement. In addition, calculations indicate that the bonding interactions between the cement and polymer remain stable over the range of strain studied.

Rod, Kenton A. (ORCID:0000000318189094)↗

The Effect of Cutting Speed in Metallic Glass Grinding

In this paper, the effects of the cutting speed in metallic glass grinding were investigated in dry conditions. The results showed that grinding forces decrease as grinding energy increase with the increasing cutting speeds. The present investigations on ground surface and grinding chips morphologies -shows that material removal and surface formation of the BMG are mainly due to the ductile chip deformation and ploughing as well as brittle fracture of some particles from the edges of the tracks. The roughness values obtained with the Cubic Boron Nitride wheels are acceptable for the grinding operation.

36 MATERIALS SCIENCE↗

Report on THMC Modeling of the Near Field Evolution of a Generic Clay Repository: Model Validation and Demonstration

Shale and clay-rich rock formations have been considered as potential host rocks for geological disposal of high-level radioactive waste throughout the world. Coupled thermal, hydrological, mechanical, and chemical (THMC) processes have a significant impact on the long-term safety of a repository in this type of rocks. For example, the excavation damaged zone (EDZ) near repository tunnels can modify local permeability (resulting from induced fractures), potentially leading to less confinement capability. Maximum allowable temperature is one of the most important design variables for a geological repository, because it determines waste package spacing, distance between disposal galleries, and therefore the overall size (and cost) of the repository for a given amount of waste. This report documents results from four R&D activities to address the above concerns: (1) development and validation of constitutive relationships (Chapter 2); (2) development of a discrete fracture network (DFN) model for investigating coupled processes in the EDZ (Chapter 3); (3) development and validation of a THM model for the Full-Scale Emplacement Experiment (FE) tests at Mont Terri, Switzerland (Chapter 4); and (4) investigation of high-temperature impacts, including both laboratory and modeling studies (Chapter 5). The overall objectives of these activities are to provide an improved understanding of and advanced modeling capabilities for EDZ evolution in clay repositories and the associated coupled processes, and to develop a technical basis for the maximum allowable temperature for a clay repository.

54 ENVIRONMENTAL SCIENCES↗

On thermal stress failure of the SNAP-19A RTG heat shield

Results of a study on thermal stress problems in an amorphous graphite heat shield that is part of the launch-abort protect system for the SNAP-19A radio-isotope thermoelectric generators (RTG) that will be used on the Viking Mars Lander are presended. The first result is from a thermal stress analysis of a full-scale RTG heat source that failed to survive a suborbital entry flight test, possibly due to thermal stress failure. It was calculated that the maximum stress in the heat shield was only 50 percent of the ultimate strength of the material. To provide information on the stress failure criterion used for this calculation, some heat shield specimens were fractured under abort entry conditions in a plasma arc facility. It was found that in regions free of stress concentrations the POCO graphite heat shield material did fracture when the local stress reached the ultimate uniaxial stress of the material.

Pitts, W. C.↗

EGS Collab Project: Status, Tests, and Data

The EGS (Enhanced Geothermal Systems) Collab project is performing stimulation and flow experiments in highly-monitored and well-characterized intermediate-scale (approximately10 to 20 meter) field test beds at a depth of approximately 1,500 meters in the Sanford Underground Research Facility (SURF) in the Black Hills of South Dakota. Our fracture stimulation and interwell flow tests are performed to better understand processes that control formation of effective subsurface heat exchangers that are critical to the development and success of EGS. Different EGS Collab stimulations will be performed under dissimilar stress conditions produce data for model comparisons that better differentiate stimulation mechanisms and the evolution of permeability enhancement in crystalline rock. EGS Collab experiments provide a means of testing tools, concepts and strategies that could later be employed under geothermal reservoir conditions at DOE’s Frontier Observatory for Research in Geothermal Energy (FORGE) and other enhanced geothermal systems. Key to the project is using numerical simulations in the experiment design and interpretation of results, and the collection of high-quality stimulation/flow, thermal, and geologic/geophysical data. A wide range of geologic and geophysical data have been acquired and interpreted for pre-stimulation testbed characterization. Multiple stimulation and flow tests have been performed at SURF, and multiple data sets have been collected and analyzed during these tests including electrical resistance tomography, microseismic, continuous active source seismic monitoring, distributed temperature, and the SIMFIP tool has been used to identify fracture formation and characteristics. An overview of some of the numerical simulations and experiments performed at SURF are presented.

15 GEOTHERMAL ENERGY↗

Residually Stressed Bimaterial Beam Specimen for Measuring Environmentally Assisted Crack Growth

Background: Subcritical crack growth can occur in a brittle material when the stress intensity factor is smaller than the fracture toughness if an oxidizing agent (such as water) is present at the crack tip. Objective: Here we present a novel bi-material beam specimen which can measure environmentally assisted crack growth rates. The specimen is “self-loaded” by residual stress and requires no external loading. Methods: Two materials with different coefficient of thermal expansion are diffusion bonded at high temperature. After cooling to room temperature a subcritical crack is driven by thermal residual stresses. A finite element model is used to design the specimen geometry in terms of material properties in order to achieve the desired crack tip driving force. Results: The specimen is designed so that the crack driving force decreases as the crack extends, thus enabling the measurement of the crack velocity versus driving force relationship with a single test. The method is demonstrated by measuring slow crack growth data in soda lime silicate glass and validated by comparison to previously published data. Conclusions: The self-loaded nature of the specimen makes it ideal for measuring the very low crack velocities needed to predict brittle failure at long lifetimes.

36 MATERIALS SCIENCE↗

Experiment design for the neutron irradiation of $\mathrm{PM-HIP}$ alloys for nuclear reactors

Here, this article describes the design of an Advanced Test Reactor (ATR) drop-in neutron irradiation experiment aiming to directly compare the performance of nuclear structural alloys fabricated by powder metallurgy with hot isostatic pressing (PM-HIP) against conventional casting or forging. There is growing interest in PM-HIP alloys for nuclear applications because of their microstructural uniformity, superior mechanical properties, and reduced dependence on welding and machining, compared to cast/forged alloys. Nuclear code-qualification of PM-HIP alloys requires neutron irradiation testing to demonstrate performance under relevant conditions. In this experiment, six nuclear structural alloys were irradiated: Ni-based alloys 625 and 690, Grade 91 ferritic steel, SA508 pressure vessel steel, and 304L and 316L austenitic stainless steels. The experiment is assembled into seven capsules in four test trains and irradiated in three ATR inboard A positions. Both the PM-HIP and cast/forged versions of each alloy were irradiated under nearly identical conditions for comparative purposes, to target doses of 1 ± 0.2 and 3 ± 0.2 dpa at temperatures of 300 ± 50 °C and 400 ± 50 °C. A thorough description of the experiment design and thermal, structural and neutronic analyses performed to ensure the targeted irradiation conditions are met is provided. Specimens were configured as small disks, compact tension specimens and tensile bars to facilitate post-irradiation examination (PIE) that will include mechanical testing, microstructure characterization, and fracture toughness testing. Given the considerations for ASTM standardized mechanical testing, comparative fluence and temperature across specimen pairs, and comprehensive PIE planning herein, this work serves as a template for future nuclear materials qualification experiment designs.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Damage tolerance of nuclear graphite at elevated temperatures

Nuclear-grade graphite is a critically important high-temperature structural material for current and potentially next generation of fission reactors worldwide. It is imperative to understand its damage-tolerant behaviour and to discern the mechanisms of damage evolution under in-service conditions. Here we perform in situ mechanical testing with synchrotron X-ray computed micro-tomography at temperatures between ambient and 1,000 °C on a nuclear-grade Gilsocarbon graphite. We find that both the strength and fracture toughness of this graphite are improved at elevated temperature. Whereas this behaviour is consistent with observations of the closure of microcracks formed parallel to the covalent-sp 2 -bonded graphene layers at higher temperatures, which accommodate the more than tenfold larger thermal expansion perpendicular to these layers, we attribute the elevation in strength and toughness primarily to changes in the residual stress state at 800–1,000 °C, specifically to the reduction in significant levels of residual tensile stresses in the graphite that are ‘frozen-in’ following processing.

36 MATERIALS SCIENCE↗

Impact Testing of Heat Source Exemplars

This report details the heat source impact testing performed at the Shock Thermodynamics Applied Research Facility (STAR). The purpose of these tests were to measure the impact behavior of a heated Ta-10W tantalum/tungsten alloy heat source exemplar. Each exemplar resembled a cylinder with a rectangular through-hole orthogonal to the cylinder axis-of-symmetry. In each test, the exemplar was impacted by a hardened steel impactor accelerated using the STAR air gun. The exemplars were impacted perpendicular to the through-hole and at an an angle to the cylindrical axis-of-symmetry. The exemplar bar stock source, impact angle, and impact velocity were varied throughout the testing series. High-speed video was used to measure dynamic impact behavior while photon doppler velocimetry (PDV) and shorting pins were used to measure the impact velocity. Foam support structures were used to thermally isolate the exemplar and provide a support structure which was non-perturbative to the impact event. Soft-catch techniques were used to minimize secondary impacts and enable recovery for detailed post-shot analysis. Results indicate positive correlation between exemplar fracture and the variables of impact velocity and impact angle. Exemplar fracture occurred consistently along a single corner of the through-hole.

36 MATERIALS SCIENCE↗