Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Steady state”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Wear-Resistant, Self-Lubricating Surfaces of Diamond Coatings

In humid air and dry nitrogen, as-deposited, fine-grain diamond films and polished, coarse-grain diamond films have low steady-state coefficients of friction (less than 0.1) and low wear rates (less than or equal to 10(exp -6) mm(exp 3)/N-m). In an ultrahigh vacuum (10(exp -7) Pa), however, they have high steady-state coefficients of friction (greater than 0.6) and high wear rates (greater than or equal to 10(exp -4) mm(exp 3)/N-m). Therefore, the use of as-deposited, fine-grain and polished, coarse-grain diamond films as wear-resistant, self-lubricating coatings must be limited to normal air or gaseous environments such as dry nitrogen. On the other hand, carbon-ion-implanted, fine-grain diamond films and nitrogen-ion-implanted, coarse-grain diamond films have low steady-state coefficients of friction (less than 0.1) and low wear rates (less than or equal to 10(exp -6) mm(exp 3)/N-m) in all three environments. These films can be effectively used as wear-resistant, self-lubricating coatings in an ultrahigh vacuum as well as in normal air and dry nitrogen.

Miyoshi, Kazuhisa↗
NASA NTRS1996

Finite Difference Time Marching in the Frequency Domain: A Parabolic Formulation for Aircraft Acoustic Nacelle Design

An explicit finite difference iteration scheme is developed to study harmonic sound propagation in aircraft engine nacelles. To reduce storage requirements for large 3D problems, the time dependent potential form of the acoustic wave equation is used. To insure that the finite difference scheme is both explicit and stable, time is introduced into the Fourier transformed (steady-state) acoustic potential field as a parameter. Under a suitable transformation, the time dependent governing equation in frequency space is simplified to yield a parabolic partial differential equation, which is then marched through time to attain the steady-state solution. The input to the system is the amplitude of an incident harmonic sound source entering a quiescent duct at the input boundary, with standard impedance boundary conditions on the duct walls and duct exit. The introduction of the time parameter eliminates the large matrix storage requirements normally associated with frequency domain solutions, and time marching attains the steady-state quickly enough to make the method favorable when compared to frequency domain methods. For validation, this transient-frequency domain method is applied to sound propagation in a 2D hard wall duct with plug flow.

Baumeister, Kenneth J.↗
NASA NTRS1996

Finite Difference Time Marching in the Frequency Domain: A Parabolic Formulation for the Convective Wave Equation

An explicit finite difference iteration scheme is developed to study harmonic sound propagation in ducts. To reduce storage requirements for large 3D problems, the time dependent potential form of the acoustic wave equation is used. To insure that the finite difference scheme is both explicit and stable, time is introduced into the Fourier transformed (steady-state) acoustic potential field as a parameter. Under a suitable transformation, the time dependent governing equation in frequency space is simplified to yield a parabolic partial differential equation, which is then marched through time to attain the steady-state solution. The input to the system is the amplitude of an incident harmonic sound source entering a quiescent duct at the input boundary, with standard impedance boundary conditions on the duct walls and duct exit. The introduction of the time parameter eliminates the large matrix storage requirements normally associated with frequency domain solutions, and time marching attains the steady-state quickly enough to make the method favorable when compared to frequency domain methods. For validation, this transient-frequency domain method is applied to sound propagation in a 2D hard wall duct with plug flow.

Baumeister, K. J.↗
NASA NTRS2018

Pulsed Fission-Fusion (PuFF)

In September 2013 the NASA Innovative Advanced Concept (NIAC) organization awarded a phase I contract to the PuFF team. Our phase 1 proposal discussed a pulsed fission-fusion propulsion system that injected gaseous deuterium (D) and tritium (T) as a mixture in a column, surrounded concentrically by gaseous uranium fluoride (UF6) and then an outer shell of liquid lithium. A high power current would flow down the liquid lithium and the resulting Lorentz force would compress the column by roughly a factor of 10. The compressed column would reach criticality and a combination of fission and fusion reactions would occur. The fission reactions would further energize the fusion center, and the fusion reactions would generate neutrons that promote more complete burnup of the fission fuel. The lithium liner provides some help as a neutron reflector but also acts as a propulsive medium, being converted to plasma which is then expanded against a magnetic nozzle for thrust. The expansion of the (primarily) lithium plasma against the nozzle's magnetic field inducts a current that is used to charge the system for the next pulse. Our concept also included secondary injection of a Field Reversed Configuration (FRC) plasmoid that would provide a secondary compression direction, axially against the column, and push the column away from the injection manifold, increasing the manifold's survivability.Our phase 1 proposal included modeling the above process first under steady state assumptions and second under a time variant integration. We proposed including these results into a Mars concept vehicle and finally proposing promising conditions to be evaluated experimentally in Phase II. In phase I we quickly realized that we needed to modify our approach. Our steady state work was completed as proposed, and the results indicated that one, a two stage compression system was not needed and two, that we wanted to move away from UF6. The steady state model shows much more margin than expected, to the point that we may well reach breakeven with the Charger – 1 facility, a 572 kJ Marx bank currently under refurbishment at UAH. Additionally we found that using gaseous D-T and UF6, provided a relatively simple prospect of using a pulsed injector, made reaching criticality more difficult. The introduction of large amounts of fluorine meant a radiative sink, sapping power from the fusion plasma and was harder to handle. Therefore we moved to a solid uranium target that held D-T under pressure. In so doing we could move our target closer to criticality and remove any material that did not sustain the reaction.

Fusion↗
NASA NTRS2005

Buoyancy Suppression in Gases at High Temperatures

The computational fluid dynamics code FLUENT was used to study Rayleigh instability at large temperature differences in a sealed gas-filled enclosure with a cold top surface and a heated bottom wall (Benard problem). Both steady state and transient calculations were performed. The results define the boundaries of instability in a system depending on the geometry, temperature and pressure. It is shown that regardless of how fast the bottom-wall temperature can be ramped up to minimize the time spent in the unstable region of fluid motion, the eventual stability of the system depends on the prevailing final pressure after steady state has been reached. Calculations also show that the final state of the system can be different depending on whether the result is obtained via a steady-state solution or is reached by transient calculations. Changes in the slope of the pressure-versus-time curve are found to be a very good indicator of changes in the flow patterns in the system.

Kuczmarski, Maria A.↗
NASA NTRS2019

Real-Time Modeling of Thermal Interactions in Cryogenic Ball Bearings

Based on the integration of classical differential equations of motion of bearing elements, a real-time dynamic simulation of ball bearing performance is coupled with simultaneous modeling of thermal interactions between the bearing elements. The transient heat generations are time averaged over a significantly larger time step before they are used to compute the changes in bearing temperature fields. Such an averaging algorithm eliminates the numerical difficulties associated with simultaneous integration of mechanical thermal differential equations with vastly different time scales. Under stable operation, the step change in temperatures at each thermal time step converges to a steady-state solution. Following is a list of accomplishments in the present investigation: (1) A real-time dynamic performance of both 440C and hybrid ball bearings in a LOX environment is modeled in both transient and steady-state time domains, as the inner race accelerates to a prescribed operating speed. (2) The frictional interactions at the ball to race contacts are modeled by experimentally measured traction coefficients as a function of slide-to-roll ratios. (3) Bearing heat generation, as defined by the heat transferred to circulating LOX, is validated against experimental values determined by measured LOX temperatures under prescribed pressures and flow rates. The predicted heat generation is in good agreement with the experimental values. (4) The steady-state solutions are shown to be independent of initial conditions. This establishes convergence of the numerical integration of a differential equation of motion of the bearing elements. (5) Churning and drag losses in the circulating LOX constitutes the majority of bearing heat generation under the experimental test conditions. (6) The heat dissipated in frictional interactions in hybrid bearings is significantly lower in hybrid bearings in comparison to that simulated in all-steel bearings, while the churning and drag losses are relatively unchanged.

Gupta, P. K.↗
NASA NTRS1990

Current collection in a magnetoplasma

The authors present a survey of a very incomplete subject, current collection in a magnetoplasma. The best-developed and simplest theories for current collection are steady-state collisionless theories, and these must be understood before departures from them can be analyzed usefully. Thus, the authors begin with a review of them. The authors include some recent numerical results which indicate that steady-state collisionless Laplace-limit currents remain substantially below the Parker-Murphy (1967) canonical upper bound out to very large electrode potentials, and approach it as a limit only very slowly if at all. Attempts to correct this theory for space-charge effects lead to potential disturbances which extend to infinite distance along the electrode's magnetic shadow, unless collisional effects are also taken into account. However, even a small amount of relative plasma drift motion, such as that involved in a typical rocket experiment, can change this conclusion fundamentally. It is widely believed that time-averaged current collection may be increased by effects of plasma turbulence, and the authors review the available evidence for and against this contention. Steady-state collisionless particle dynamics predicts the existence of a toroidal region of trapped orbits which surrounds the electrode. Light emissions from this region have been photographed, indicating that collisional ionization may also occur there, and this, and/or scattering by collisions or possibly turbulent fluctuations in this region, may also increase current collection by the electrode. The authors also discuss effects on particle motions near the electrode, associated with breakdown of magnetic insulation in the region of large electric fields near it.

Laframboise, Jim G.↗
DOE OSTI2024

Correlation functions from tensor network influence functionals: The case of the spin-boson model

We investigate the application of matrix product state (MPS) representations of the influence functionals (IFs) for the calculation of real-time equilibrium correlation functions in open quantum systems. Focusing specifically on the unbiased spin-boson model, we explore the use of IF-MPSs for complex time propagation, as well as IF-MPSs for constructing correlation functions in the steady state. We examine three different IF approaches: one based on the Kadanoff–Baym contour targeting correlation functions at all times, one based on a complex contour targeting the correlation function at a single time, and a steady state formulation, which avoids imaginary or complex times, while providing access to correlation functions at all times. We show that within the IF language, the steady state formulation provides a powerful approach to evaluate equilibrium correlation functions.

Chemistry↗
DOE OSTI2025

A Reinforcement Learning Approach to Augment Conventional PID Control in Nuclear Power Plant Transient Operation

The ability of nuclear reactors to operate their power conversion cycles more flexibly will enhance their value to energy grids with variable pricing. Current nuclear control systems are typically classical controllers that are often based on proportional-integral-derivative (PID) control. This paper presents a method of augmenting the existing PID control for difficult transient operations in nuclear power plants using a reinforcement learning–derived feedforward signal applied in real time. The agents, which are trained on a test thermal load-following problem, are designed to improve steam generator outlet temperature control for a range of fast load-following scenarios covering ramp rates from 9%/min to 15%/min. Several reinforcement learning algorithms were initially investigated for the training of the feedforward agents with deep Q-learning (DQN) and proximal policy optimization (PPO) networks, which were found to be the most promising. The DQN controllers utilize discrete actions, giving them a better disturbance rejection at steady state but inconsistent response to initial temperature deviations. In contrast, PPO-trained agents, which take continuous actions except for a dead zone around zero, were shown to have the best combination of high disturbance rejection at steady state and good tracking of the desired temperature value. The ability of the PPO agent was also examined, with the average time of decision making found to be on the order of 1 ms. The fault properties of the controller under the loss of the reinforcement learning agent feedforward signal were also examined. The controller showed strong performance in situations of “no-signal” faults. but was less good at handling “stuck-at” faults, where the feedforward signal remains at a set value. In both cases, however, the PID was able to successfully maintain stability, eventually returning the system to a steady state. It is hoped that this work will allow for the proposed control architecture to be examined for more difficult control problems such that it may eventually be used to adapt existing nuclear plants for more aggressive load-following on grids of the future.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1951

Investigation of dynamic characteristics of a turbine-propeller engine

Time constants that characterize engine speed response of a turbine-propeller engine over the cruising speed range for various values of constant fuel flow and constant blade angle were obtained both from steady-state characteristics and from transient operation. Magnitude of speed response to changes in fuel flow and blade angle was investigated and is presented in the form of gain factors. Results indicate that at any given value of speed in the engine cruising speed range, time constants obtained both from steady-state characteristics and from transient operation agree satisfactorily for any given constant fuel flow, whereas time constants obtained from transient operation exceed time constants obtained from steady-state characteristics by approximately 14 percent for any given blade angle.

ENGINES, TURBO-PROPELLER↗
DOE OSTI2021

Diagnosing nuclear power plant pipe wall thinning due to flow accelerated corrosion using a passive, thermal non-destructive evaluation method: Feasibility assessment via numerical experiments

Flow accelerated corrosion (FAC) in nuclear power plant pipes is one of the leading causes of accidents, fatalities, damage and outages. Current FAC identification methods employ expensive sensing technology and are “active” methods, where the response of the piping system to an externally-generated thermal, mechanical or optical excitation must be measured. As a result, these techniques require a disruptive and time-consuming setup. Here we propose a method that utilizes pipe surface temperature measurements to passively monitor for FAC-induced pipe wall thinning without the need for expensive equipment or post-installation setup time. This diagnostic method utilizes a simulation data-driven diagnostic model to estimate the amount of thickness reduction in a pipe based on changes in measured steady-state pipe temperatures. In order to reduce the computational burden of generating large, simulation-based datasets, the behavior of the insulation of the pipe was modeled using a suitably calibrated heat transfer boundary parameter. Additionally, global sensitivity analysis was performed to determine system parameter(s), such as the temperature of water flowing inside the pipe, which significantly affect the steady state pipe wall temperature and could cause errors in diagnosis. Two diagnostic models, one using only the change in steady-state temperature as an indicator for FAC-induced pipe wall thinning and the other using water temperature as an additional diagnostic model input were evaluated for their ability to estimate thickness reductions in a pipe using simulated pipe wall temperature data. For the numerical experiments conducted in this work, both models estimated wall thickness with errors within 0.5 mm, indicating that the proposed technique can potentially be used as a low-cost, first-pass method for FAC monitoring.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS2001

The NO(x)-HNO3 System in the Lower Stratosphere: Insights from In Situ Measurements and Implications of the J(HNO3)-[OH] Relationship

During the 1997 Photochemistry of Ozone Loss in the Arctic Region in Summer (POLARIS) mission, simultaneous in situ observations of NOx and HOx radicals, their precursors, and the radiation field were obtained in the lower stratosphere. We use these observations to evaluate the primary mechanisms that control NOx-HNO3 exchange and to understand their control over the partitioning between NO2 and HNO3 in regions of continuous sunlight. We calculate NOx production (PNOx) and loss (LNOx) in a manner directly constrained by the in situ measurements and current rate constant recommendations, using approaches for representing albedo, overhead O3 and [OH] that reduce model uncertainty. We find a consistent discrepancy of 18% between modeled rates of NOx production and loss (LNOx = 1.18P(sub NOx)), which is within the measurement uncertainty of +/- 27%. The partitioning between NOx production processes is [HNO3 + OH (41 +/- 2)%; HNO3 + hv (59 +/- 2)%] and between NOx loss processes is [NO2 + OH, 90% to >97%; BrONO2 + H2O, 10% to <3%]. The steady-state description of NOx-HNO3 exchange reveals the significant influence of the tight correlation between the photolysis rate of HNO3 and [OH] established by in situ measurements throughout the lower stratosphere. Parametrizing this relationship, we find: (1) the steady-state value of [NO2](sub 24h-avg)/[HNO3] in the continuously sunlit, lower stratosphere is a function only of temperature and number density; and (2) the partitioning of NOx production between HNO3 + OH and HNO3 + hv is nearly constant throughout most of the lower stratosphere. We describe a methodology (functions of latitude, day, temperature, and pressure) for accurately predicting the steady-state value of [NO2](sub 24h-avg)/[HNO3] and the partitioning of NOx production within these regions. The results establish a metric to compare observations of [NO2](sub 24h-avg)/[HNO3] within the continuously sunlit region and provide a simple diagnostic for evaluating the accuracy of models that attempt to describe the coupled NOx-HOx photochemistry in the lower stratosphere.

Perkins, K. K.↗
NASA NTRS1985

Nonlinear flap-lag-extensional vibrations of rotating, pretwisted, preconed beams including Coriolis effects

The effects of pretwist, precone, setting angle, Coriolis forces and second degree geometric nonlinearities on the natural frequencies, steady state deflections and mode shapes of rotating, torsionally rigid, cantilevered beams were studied. The governing coupled equations of flap lag extensional motion are derived including the effects of large precone and retaining geometric nonlinearities up to second degree. The Galerkin method, with nonrotating normal modes, is used for the solution of both steady state nonlinear equations and linear perturbation equations. Parametric indicating the individual and collective effects of pretwist, precone, Coriolis forces and second degree geometric nonlinearities on the steady state deflection, natural frequencies and mode shapes of rotating blades are presented. It is indicated that the second degree geometric nonlinear terms, which vanish for zero precone, can produce frequency changes of engineering significance. Further confirmation of the validity of including those generated by MSC NASTRAN. It is indicated that the linear and nonlinear Coriolis effects must be included in analyzing thick blades. The Coriolis effects are significant on the first flatwise and the first edgewise modes.

Subrahmanyam, K. B.↗
NASA NTRS1977

Analysis of the passive stabilization of the long duration exposure facility

The nominal Long Duration Exposure Facility (LDEF) configurations and the anticipated orbit parameters are presented. A linear steady state analysis was performed using these parameters. The effects of orbit eccentricity, solar pressure, aerodynamic pressure, magnetic dipole, and the magnetically anchored rate damper were evaluated to determine the configuration sensitivity to variations in these parameters. The worst case conditions for steady state errors were identified, and the performance capability calculated. Garber instability bounds were evaluated for the range of configuration and damping coefficients under consideration. The transient damping capabilities of the damper were examined, and the time constant as a function of damping coefficient and spacecraft moment of inertia determined. The capture capabilities of the damper were calculated, and the results combined with steady state, transient, and Garber instability analyses to select damper design parameters.

Siegel, S. H.↗
DOE OSTI2025

From Depletion to Restoration: Lessons From Long‐Term Monitoring of Carbon Gains and Losses in Cropping Systems

As global atmospheric CO 2 rapidly approaches a key tipping point, there is an urgent need to implement strategies to reverse this pattern. A generally accepted understanding of carbon (C) in agricultural fields includes: (H1) substantial C loss occurs when natural vegetation is converted to crops, (H2) soils typically reach a steady-state C concentration under contemporary practices, and (H3) improved management or crop selection can enhance soil C stocks over time. Significant variability exists, but studies consistently show large C losses from agricultural ecosystems, supporting H1. Although steady-state C levels (H2) are commonly assumed, measuring C gains or losses in mature agroecosystems is challenging. Efforts to increase soil C storage (H3) have limited data due to the diversity of potential practices, compounded by substantial variability in soil C measurements. Here, long-term (7–17 year) ecosystem C flux data from diverse cropping systems revealed that conventionally tilled annual row crops (maize and soybean) act as significant long-term atmospheric C sources, challenging H2. Furthermore, conservation tillage practices reduced C losses compared with conventional tillage but showed minimal evidence for long-term ecosystem C storage, even after 20+ years. This indicates that no-till practices reduce C losses but imply that no soil C is added, challenging H3. By contrast, perennial Miscanthus × giganteus, Panicum virgatum, and restored tallgrass prairie systems store C at the ecosystem scale more effectively than minimally tilled annual row crops. Analysis over multiple years demonstrates significant ecosystem C storage with perennial crops, varying by species, starting in the first year of transition. These findings, although focused on one region, suggest that the assumptions of steady-state C levels and increased storage from conservation practices do not universally apply and that significant changes to agroecosystems are required to increase C storage.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1971

The creep properties of dispersion-strengthened silver-gallium oxide alloys.

Steady-state creep rates were measured for two preparations of a dispersion-strengthened alloy of silver with 1 mol % gallium oxide. One preparation, an internally-oxidized type, had a grain size 40 times that of the other preparation, which was a consolidated-powder type of alloy. The temperature and stress dependence of the steady-state creep rate differs widely for the two alloys and must be attributed to the difference in grain size. The activation energy for steady-state creep of the internally-oxidized coarse grained material is near that for self-diffusion of silver, which strongly indicates a creep process controlled by dislocation climb.

Lenel, F. V.↗
NASA NTRS1991

Steady and unsteady solutions of the incompressible Navier-Stokes equations

An algorithm for the solution of the incompressible Navier-Stokes equations in three-dimensional generalized curvilinear coordinates is presented. The algorithm can be used to compute both steady-state and time-dependent flow problems. The algorithm is based on the method of artificial compressibility and uses a third-order flux-difference splitting technique for the convective terms and the second-order central difference for the viscous terms. The accuracy is obtained in the numerical solutions by subiterating the equations in pseudotime for each physical time step. The equations are solved with a line-relaxation scheme that allows the use of very large pseudotime steps leading to fast convergence for steady-state problems as well as for the subiterations of time-dependent problems. The steady-state solution of flow through a square duct with a 90-deg bend is computed, and the results are compared with experimental data. Good agreement is observed. Computations of unsteady flow over a circular cylinder are presented and compared to other experimental and computational results. Finally, the flow through an artificial heart configuration with moving boundaries is calculated and presented.

Rogers, Stuart E.↗
DOE OSTI2025

Microstructural and rheological training and memory of nanocolloidal soft glasses under cyclic shear

An intrinsic feature of disordered and out-of-equilibrium materials, such as glasses, is the dependence of their properties on their history. An important example is rheological memory, in which disordered solids obtain properties based on their deformation history. Here, in this study, we employ x-ray photon correlation spectroscopy with in situ rheometry to characterize memory formation in a nanocolloidal soft glass due to cyclic shear. During a cycle, particles undergo irreversible displacements composed of a combination of shear-induced diffusion and heterogeneous, residual strain fields. At lower shear amplitudes, the displacements resemble a random walk in which the directions in each cycle are independent of those in preceding cycles, while at high amplitude, the irreversible displacements in consecutive cycles become correlated. The magnitudes of the displacements decrease with each cycle before reaching a steady state where the microstructure has been trained to achieve enhanced reversibility even at shear amplitudes well above yielding and despite the presence of thermal fluctuations. At amplitudes below and near yielding, these decreases are monotonic, while well above yielding, they are nonmonotonic, suggesting evidence of shear banding. Accompanying this microstructural training are corresponding decreases in the dissipation during each cycle and the magnitude of the residual stress toward steady-state values. Memory of the training is revealed by measurements in which the amplitude of the shear is changed after steady state is reached. The magnitude of the particle displacements, as well as the dissipation and the change in residual stress, vary nonmonotonically with the new shear amplitude, having minima near the training amplitude, thereby revealing correlated microscopic and macroscopic signatures of memory.

Chen, Yihao [Johns Hopkins Univ., Baltimore, MD (U↗