Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Shear Strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

The nonlinear rheology of complex yield stress foods

Many foods have a yield stress that allows them to retain a desired shape at rest, but transition into a viscous fluid when being served or consumed. The determination of the yield stress of the food dictates how the foods are formed and packaged, how they are served, and how they are perceived when being eaten. Oscillatory shearing provides an ideal test protocol to map the rheology across a range of time and flow strength scales. We couple oscillatory shearing and an iterative recovery procedure to show that the yielding process is a continuous transition for two common yield stress foods. We show that unrecoverable processes from oscillatory tests are equivalent to the steady shear flow behavior. We show that this yielding behavior can be well approximated by a recently published model that treats yield stress materials as continuous viscoelastic fluids with a rate-dependent relaxation time and has parameters that can be obtained from the linear viscoelastic oscillatory frequency sweep and the steady shear flow curve.

Griebler, James J.↗

Basal hydraulic conditions of Ice Stream B

Fifteen boreholes have been drilled to the base of Ice Stream B in the vicinity of UpB Camp. The boreholes are spread over an area of about 500 x 1000 m. Several till cores were retrieved from the bottom of the 1000-m-deep holes. Laboratory tests using a simple shear box revealed a yield strength of basal till of 2 kPa. This agrees well with in-situ measurements using a shear vane. Since the average basal shear stress of Ice Stream B with a surface slope of 0.1 degree is about 20 kPa, the ice stream cannot be supported by till that weak. Additional support for this conclusion comes from the basal water pressure that has been measured in all boreholes as soon as the hot water drill reached bottom. In several boreholes, the water pressure has been continuously monitored; in two of them, over several years. The water pressure varies but stays within 1 bar of flotation where ice overburden pressure and water pressure are equal. The ratio of water and overburden pressure lies between 0.986 and 1.002. This is an extremely high value as compared to other fast-moving ice masses; e.g., Variegated Glacier in surge has a ratio of 0.8, and Columbia Glacier - a fast-moving tidewater glacier - has a ratio of 0.9. It implies that water flow under the glacier occurs in a thin film and not in conduits that would drain away water too rapidly. It also implies that basal sliding must be very effective. Water flow under the glacier was measured in a salt-injection experiment where a salt pulse was released at the bottom of a borehole while 60 m down-glacier, the electrical resistance was measured between two other boreholes. A flow velocity of 7 mm/s was obtained.

Engelhardt, Hermann↗

Compositional effects on cure kinetics, mechanical properties and printability of dual-cure epoxy/acrylate resins for DIW additive manufacturing

Interest in 3D printing of thermoset resins has increased significantly in recent years. One approach to additive manufacturing of thermoset resins is printing dual-cure resins with direct ink write (DIW). Dual-cure resins are multi-component resins which employ an in situ curable constituent to enable net-shape fabrication while a second constituent and cure mechanism contribute to the final mechanical properties of the printed materials. In this work, the cure kinetics, green strength, printability, and print fidelity of dual-cure epoxy/acrylate thermoset resins are investigated. Resin properties are evaluated as a function of acrylate concentration and in situ UV exposure conditions. The acrylate cure kinetics are probed using photo-differential scanning calorimetry and the impacts of resin composition and UV cure profile on the acrylate extent of conversion are presented. Continuous and pulsed UV cure profiles are shown to affect total conversion due to variances in radical efficiency at different UV intensities and acrylate concentrations. The effects of acrylate concentration on the kinetics of the epoxy thermal cure and the final mechanical properties are also investigated using dynamic mechanical analysis and three-point bend measurements. The glass transition temperature is dependent on formulation, with increasing acrylate content decreasing the T g . However, the room temperature shear moduli, flexural moduli, strength, strain-to-failure, and toughness values are relatively independent of resin composition. The similarity of the final properties allows for greater flexibility in resin formulation and in situ cure parameters, which can enable the printing of complex parts that require high green strength. We found that the in situ UV print intensities and exposure profiles that are necessary to achieve the best print quality are not, in most cases, the conditions that maximize conversion of the acrylate network. Lastly, this highlights the importance of developing optimized resin compositions which enable complete cure of the acrylate network by promoting acrylate dark cure or thermal cure.

36 MATERIALS SCIENCE↗

Environmental sensitivities of shallow-cumulus dilution – Part 2: Vertical wind profile

This second part of a numerical study on shallow-cumulus dilution focuses on the sensitivity of cloud dilution to changes in the vertical wind profile. Insights are obtained through large-eddy simulations of maritime and continental cloud fields. In these simulations, the speed of the initially uniform geostrophic wind and the strength of geostrophic vertical wind shear in the cloud and subcloud layer are varied. Increases in the cloud-layer vertical wind shear (up to 9 ms -1 km -1 ) lead to 40%–50% larger cloud-core dilution rates compared to their respective unsheared counterparts. When the background wind speed, on the other hand, is enhanced by up to 10 ms -1 and subcloud-layer vertical wind shear develops or is initially prescribed, the dilution rate decreases by up to 25%. The sensitivities of the dilution rate are linked to the updraft strength and the properties of the entrained air. Increases in the wind speed or vertical wind shear result in lower vertical velocities across all sets of experiments with stronger reductions in the cloud-layer wind shear simulation (27%–47%). Weaker updrafts are exposed to mixing with the drier surrounding air for a longer time period, allowing more entrainment to occur (i.e., the “core-exposure effect”). However, reduced vertical velocities, in concert with increased cloud-layer turbulence, also assist in widening the humid shell surrounding the cloud cores, leading to entrainment of more humid air (i.e., the “core–shell dilution effect”). In the experiments with cloud-layer vertical wind shear, the core-exposure effect dominates and the cloud-core dilution increases with increasing shear. Conversely, when the wind speed is increased and subcloud-layer vertical wind shear develops or is imposed, the core–shell dilution effect dominates to induce a buffering effect. The sensitivities are generally stronger in the maritime simulations, where weaker sensible heat fluxes lead to narrower, more tilted, and, therefore, more suppressed cumuli when cloud-layer shear is imposed. Moreover, in the experiments with subcloud wind shear, the weaker baseline turbulence in the maritime case allows for a larger turbulence enhancement, resulting in a widening of the transition zones between the cores and their environment, leading to the entrainment of more humid air.

54 ENVIRONMENTAL SCIENCES↗

Experimental evaluation of two 36 inch by 47 inch graphite/epoxy sandwich shear webs

The design is described and test of two large (36 in. x 47 in.) graphite/epoxy sandwich shear webs. One sandwich web was designed to exhibit strength failure of the facings at a shear load of 7638 lbs/in., which is a characteristic loading for the space shuttle orbiter main engine thrust beam structure. The second sandwich web was designed to exhibit general instability failure at a shear load of 5000 lbs/in., to identify problem areas of stability critical sandwich webs and to assess the adequacy of contemporary analysis techniques.

Bush, H. G.↗

Prefabricated High-Strength Rebar Systems with High-Performance Concrete for Accelerated Construction of Nuclear Concrete Structures

This project aimed to reduce the field construction times and fabrication costs of reinforced concrete (RC) nuclear structures through the use of: 1) high-strength steel deformed reinforcing bar (rebar); 2) prefabricated high-strength rebar (HSR) assemblies with headed anchorages; and 3) high-strength concrete (HSC). The focus of the project was not to develop new innovations on materials, but rather to fill a major knowledge gap on the effectiveness, code conformity, and viability (i.e., practicality, commercial availability) of existing high-strength materials in nuclear structures, especially in shear walls, their connections/joints, and around penetrations. These advances promote the Nuclear Energy Enabling Technologies Advanced Methods for Manufacturing (NEET-1) goals of accelerating deployment schedules by at least 6 months and reducing component fabrication costs by 20% or more. Toward this vision, the following objectives were identified and completed: Develop limit-benefit and cost-benefit analysis frameworks: The structural and economic limits and benefits of HSR and HSC in nuclear walls were evaluated. Importantly, it was found that modest increases in concrete strength up to 10.0 ksi and rebar yield strength up to 100 ksi result in the most economic designs and improved structural performance (Barbachyn et al., 2017a and Barbachyn et al., 2017b). Also, an industry survey was distributed to determine the cost benefits associated with prefabrication. Importantly, on-site worker-hours are significantly reduced, allowing for significantly accelerated construction schedules (Devine et al. 2018b). Develop an optimization methodology for structural design: An optimization study was deemed not necessary since the trivial solution with maximized use of high-strength materials and prefabrication always resulted in the largest cost and time savings. Instead, the benefits (and limits) of high-strength materials and prefabrication on construction costs and on-site construction time were investigated through a parametric study. Cost-reductions through the use of HSR and HSC were found to be greater than 40%. Also, on-site construction time of nuclear shear walls can be reduced by up to 83% through the use of prefabricated rebar assemblies. Conduct experimental evaluations of nuclear shear walls and wall-foundation joints: A large scale experimental program was completed on shear-critical RC cantilever deep beams. From these experiments, it was demonstrated that increasing rebar yield strength had a greater effect on increasing lateral strength than increasing the concrete compressive strength. Further, using HSR together with HSC resulted in the highest lateral strength and displacement ductility (Devine et al. 2018a). Additionally, large-scale reversed-cyclic lateral load tests were conducted on RC shear walls. It was demonstrated that through the utilization of HSR and HSC, a wall with 55% reduced vertical and horizontal rebar area was able to achieve 91% of the peak lateral strength of a conventional wall using state-of-practice materials with the same geometry. Further, trim reinforcement with headed anchorages around the penetrations proved to be effective. Develop validated numerical simulation models: Numerical modeling was completed in two phases during this project using 3 different finite element software packages. The first phase used existing measured data from previous experimental studies on stocky RC walls to validate simplified predictive models. Models using two different programs were validated based on a database of 38 stocky walls (Barbachyn et al., 2017a). The second phase occurred after experimental testing using a third and more detailed finite element package. Prediction improvements for the initial stiffness, lateral deformations, damage propagation, and failure mechanisms were targeted. The resulting detailed models more accurately predicted the peak lateral strength, initial and secant stiffnesses, lateral deformations, and cracking patterns of the wall test specimens subjected to reversed-cyclic lateral loading as compared to the simplified pretest models. Develop validated design procedures, tools, and criteria: This project evaluated the accuracy of existing closed-form design equations from U.S. building design standards and previous research (Barbachyn et al. 2017a and Devine et al. 2018a). It was shown that the current predictive equations for shear strength capacity need to be revisited as they provide significant scatter and gross overestimates, indicating the potential for unconservative designs. Further, for both the deep beam and shear wall specimens, the numerical models and flexural capacity predictions provided the most accurate strength predictions. Develop cost-effective field construction procedures: To promote the use of prefabricated rebar assemblies, the following construction conditions where prefabrication would be used instead of in-place rebar tying were identified from an industry survey: 1) to save on construction schedule; 2) to improve safety and/or quality control; 3) for areas with heavy rebar congestion; and 4) for structures with significant repetition in rebar layout. All of these conditions directly apply and benefit nuclear construction where construction costs and schedules are extensive, safety and quality are of utmost importance, the reinforcement is extremely dense, and the reinforcement layout is repetitive in many regions of the shear walls. Additionally, an experimental study was conducted to investigate the changes in bar spacing (with respect to code-required rebar spacing and placement tolerances) when a horizontally assembled prefabricated two-dimensional (2D) rebar mat or three-dimensional (3D) rebar cage is lifted (or tripped) to a vertical position. It was found that the bars involved in both the lateral translation of the rebar assemblies (i.e., movement of the assembly in its horizontal position) and the tripping process were most susceptible to large spacing changes, and thus, their positions within the assembly would need to be checked after the placement of the assembly in place within the formwork. Importantly, the spacings of all of the other bars in the assembly were not affected significantly by the lateral translation and tripping process, thereby eliminating the need to recheck their positions within the assembly (Devine et al. 2018b).

36 MATERIALS SCIENCE↗

Tribological Performance of Ni{sub 3}Al Matrix Self-Lubricating Composites Containing Multilayer Graphene Prepared by Additive Manufacturing

In order to improve tribological performance of Ni{sub 3}Al-based alloy, Ni{sub 3}Al matrix composites containing 1.5 wt.% multilayer graphene (MLG) are prepared through additive manufacturing (AM) and spark plasma sintering (SPS), which are denoted as NMAM and NMSPS, respectively. Tribological behaviors of NMAM and NMSPS against Si{sub 3}N{sub 4} balls are researched under constant speed (0.2 m/s) and varied loads (from 4 to 16 N) for evaluating the tribological properties of NMAM and NMSPS. The results present that NMAM exhibits the excellent tribological properties [low friction coefficients (0.26-0.40) and considerable wear resistance (2.8-4.6 × 10{sup −5} mm{sup 3} N{sup −1} m{sup −1})] as compared to NMSPS, which attributes to the uniform enrichment of MLG with properties of high tensile strength and being easily sheared off on the worn surfaces. Owing to the use of spherical prealloyed powder containing multilayer graphene and the characteristics of layer by layer depositing in the AM process, NMAM has a more compact and uniform substrate, which persistently provides a source of the formation of continuous and stable frictional layer. Due to the characteristics of AM rapid solidification, NMAM has the small grain size and well-compacted microstructure, which can effectively reduce the probability of spalling wear and lead to the increase in wear resistance of materials. The research can offer the reference for self-lubricating materials prepared by AM technology.

36 MATERIALS SCIENCE↗

Tracking control of colloidal particles through non-homogeneous stationary flows

We consider the problem of controlling the trajectory of a single colloidal particle in a fluid with steady non-homogeneous flow. We use a Langevin equation to describe the dynamics of this particle, where the friction term is assumed to be given by the Faxén's Theorem for the force on a sphere immersed in a stationary flow. We use this description to propose an explicit control force field to be applied on the particle such that it will follow asymptotically any given desired trajectory, starting from an arbitrary initial condition. We show that the dynamics of the controlled particle can be mapped into a set of stochastic harmonic oscillators and that the velocity gradient of the solvent induces an asymmetric coupling between them. We study the particular case of a Brownian particle controlled through a plane Couette flow and show explicitly that the velocity gradient of the solvent renders the dynamics non-stationary and non-reversible in time. We quantify this effect in terms of the correlation functions for the position of the controlled particle, which turn out to exhibit contributions depending exclusively on the non-equilibrium character of the state of the solvent. In order to test the validity of our model, we perform simulations of the controlled particle moving in a simple shear flow, using a hybrid method combining molecular dynamics and multi-particle collision dynamics. We confirm numerically that the proposed guiding force allows for controlling the trajectory of the micro-sized particle by obligating it to follow diverse specific trajectories in fluids with homogeneous shear rates of different strengths. In addition, we find that the non-equilibrium correlation functions in simulations exhibit the same qualitative behavior predicted by the model, thus revealing the presence of the asymmetric non-equilibrium coupling mechanism induced by the velocity gradient.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Zonal flow screening in negative triangularity tokamaks

Here, this paper presents a comparative study of zonal flow screening in positive and negative triangularity tokamaks. Neoclassical screening sets the strength of zonal flow shear for fixed drive and damping. Orbit calculations show that the radial excursions of trapped particles are reduced in negative triangularity tokamaks, as compared to positive triangularity. Yet surprisingly, the neoclassical dielectric susceptibility actually increases with decreasing triangularity, such that the susceptibility is higher for negative triangularity than for positive triangularity. This is because the reduction in neoclassical polarization by shrinking the banana width is offset by the increase in neoclassical polarization by the enhancement of trapped fraction for negative triangularity. As a result, the zonal flow screening length is actually enhanced for negative triangularity, as compared to positive triangularity. Hence, the zonal flow residual is smaller for negative triangularity than for positive triangularity. Results from gyrokinetic simulations support the analytic calculations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Rayleigh-Taylor-instability experiments with elastic-plastic materials

A rotating wheel experimental facility was developed to investigate incompressible Rayleigh-Taylor instability in elastic-plastic materials. A soft solid (mayonnaise) was chosen as the elastic-plastic material for experiments; material properties that include shear modulus and yield strength were fully characterized using a vane spindle type rheometer. Initial perturbations of varying amplitudes and wavelengths were generated on the interface of the soft solid using sinusoidal cutting guides. A backlit imaging technique was used in conjunction with a high-speed camera to track the motion of the interface at various phases of the instability. Results for both two- and three-dimensional perturbations were compared to study the acceleration required for instability and the growth after the interface yielded. Exponential growth rates were observed after instability was reached with trends of increasing growth rates for lower initial amplitudes. It was found that the acceleration required for instability increased when initial amplitude and wavelength decreased. Here, three-dimensional interfaces were found to be more stable. For both cases, a decrease in initial amplitude produced a more stable interface that increased the threshold acceleration required for the instability. Critical amplitude conditions for instability were calculated and compared with various analytical models and other experimental results.

42 ENGINEERING↗

Kelvin Helmholtz Instability in Strongly Coupled Yukawa Liquids

Using 'first principles' molecular dynamics simulations Kelvin Helmholtz instability has been observed for the first time at the particle level in two-dimensional strongly coupled Yukawa liquids. At a given coupling strength {Gamma} a subsonic shear profile is superposed on an equilibrated Yukawa liquid and instability is observed. Linear growth rates computed directly from MD simulations are seen to increase with strong coupling. Vortex-roll formation in the nonlinear regime is reported.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Influence of the Cobalt Content on the Strength Properties of Tungsten Carbide Ceramics under Dynamic Loads

Based on the registration and analysis of the full wave profiles, the Hugoniot elastic limit and spall strength of ceramics based on tungsten carbide with different cobalt content are measured. We also study the influence of the cobalt content on the mechanical characteristics of tungsten carbide such as hardness, fracture strength, Young’s modulus, shear modulus, and sound velocity. It is shown that in the process of spalling, the failure stresses grow and the dynamic elastic limit decreases almost linearly within the scatter of their values with growing cobalt content; moreover, the value of the Hugoniot elastic limit is abruptly practically halved as the cobalt content grows from 0 to 2 wt %.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fallon FORGE: Analogue Outcrop Samples

Compilation of results for mechanical and fluid flow properties of analogue outcrop samples - experimental data for compressional and shear wave velocities, tensile strengths, and compressive strengths. Outcrop location and sample orientation data are documented in a separate csv file.

15 GEOTHERMAL ENERGY↗

Utah FORGE 5-2428: Coupled Investigation of Fracture Permeability Impact on Reservoir Stress and Seismic Slip - 2024 Annual Workshop Presentation

This is a presentation on the Coupled Investigation of Fracture Permeability Impact on Reservoir Stress and Seismic Slip Behavior by Lawrence Livermore National Laboratory, presented by Kayla Kroll. This presentation addresses testing and modelling related to the dependency of EGS production on sustained permeability and sufficient fluid flow through pre-existing or induced fractures in hot rock. This presentation was featured in the Utah FORGE R&D Annual Workshop on August 13, 2024.

15 GEOTHERMAL ENERGY↗

Helium Bubble Growth and Retention Characteristics in Aging Palladium Tritide

The helium-related characteristics of aged palladium tritide, including tritium loss, the formation of He bubbles from tritium decay-induced He atoms, and He thermal desorption behavior are computed using a continuum model of bubble evolution that incorporates the log-normal bubble spacing distribution deduced from 3 He nuclear magnetic resonance (NMR) measurements. This spacing distribution produces significant differences between mean (expectation) values of the bubble size and pressure and the average (median) values of these aging characteristics obtained by a previous calculation. The new calculations find much of the He is retained in a large quantity of smaller bubbles with higher bubble pressures, improving the overall stability of the bubbles and extending the age of He retention. By contrast, the integrated tritide material characteristics of swelling and tritium pressure are found relatively insensitive to details of the bubble spacing distribution. Inter-bubble fracture is predicted to begin with small, closely-spaced bubbles and progress to include larger bubbles near the onset of rapid He release. The critical concentration for this onset increases almost linearly with material tensile strength and decreases with shear modulus. Release of He from the aging solid is modeled as a growing network of fractured inter-bubble ligaments. For small particle or small grain material, the physical size of the fracture cluster, relative to the material dimensions, becomes important. In contrast with normal aging, inter-bubble fracture occurring during thermal desorption appears to begin with large, widely-spaced bubbles, indicating elevated temperature techniques may be of limited use for evaluating development of the bubble fracture network.

74 ATOMIC AND MOLECULAR PHYSICS↗

Graphite fiber reinforced thermoplastic resins

Mechanical properties of neat resin samples and graphite fiber reinforced samples of thermoplastic resins were characterized with particular emphasis directed to the effects of environmental exposure (humidity, temperature and ultraviolet radiation). Tensile, flexural, interlaminar shear, creep and impact strengths were measured for polysulfone, polyarylsulfone and a state-of-the-art epoxy resin samples. In general, the thermoplastic resins exhibited environmental degradation resistance equal to or superior to the reference epoxy resin. Demonstration of the utility and quality of a graphite/thermoplastic resin system was accomplished by successfully thermoforming a simulated compressor blade and a fan exit guide vane.

Novak, R. C.↗

Improved impact-resistant boron-aluminum composites for use as turbine engine fan blades

Efforts to improve the impact resistance of B/Al are reviewed and analyzed. Thin sheet Charpy and Izod impact tests and standard full size Charpy impact tests were conducted on unidirectional and angleply composites containing 4, 5.6 and 8 mil boron in 1100, 2024, 5052 and 6061 Al matrices. Impact failure modes of B/Al are proposed in an attempt to describe the mechanisms involved and to provide insight for maximizing impact resistance. The impact strength of B/Al was significantly increased by proper selection of materials and processing. The use of more ductile matrices (1100 Al) and larger diameter (8 mil) boron fibers gave the highest impact strengths by allowing matrix shear deformation and multiple fiber breakage.

Mcdanels, D. L.↗