Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SUPERSONIC FLIGHT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
NASA NTRS1957

Flight Investigation of a Roll-stabilized Missile Configuration at Varying Angles of Attack at Mach Numbers Between 0.8 and 1.79

A missile research model was flown at supersonic speed to determine the quality of automatic roll stabilization at varying angles of attack. Aerodynamic rolling and pitching derivatives were determined from the flight record. It was concluded that the combination of the gyro-actuated automatic pilot with wing-tip ailerons provided adequate roll stabilization under conditions encountered in flight.

INSTRUMENTS↗
NASA NTRS1953

Free-flight Performance of a Rocket-boosted, Air-launched 16-inch-diameter Ram-jet Engine at Mach Numbers up to 2.20

The investigation of air-launched ram-jet engines has been extended to include a study of models with a nominal design free-stream Mach number of 2.40. These models require auxiliary thrust in order to attain a flight speed at which the ram jet becomes self-accelerating. A rocket-boosting technique for providing this auxiliary thrust is described and time histories of two rocket-boosted ram-jet flights are presented. In one flight, the model attained a maximum Mach number of 2.20 before a fuel system failure resulted in the destruction of the engine. Performance data for this model are presented in terms of thrust and drag coefficients, diffuser pressure recovery, mass-flow ratio, combustion efficiency, specific fuel consumption, and over-all engine efficiency.

AIR INLETS - NOSE, ANNULAR↗
NASA NTRS2017

Development of Models for Disk-Gap-Band Parachutes Deployed Supersonically in the Wake of a Slender Body

The Advanced Supersonic Parachute Inflation Research and Experiments (ASPIRE) project will investigate the supersonic deployment, inflation, and aerodynamics of Disk- Gap-Band (DGB) parachutes in the wake of a slender body. The parachutes will be full-scale versions of the DGBs used by the Mars Science Laboratory in 2012 and planned for NASA’s Mars 2020 project and will be delivered to targeted deployment conditions representative of flight at Mars by sounding rockets launched out of NASA’s Wallops Flight Facility. The parachutes will be tested in the wake of a slender payload whose diameter is approximately a sixth that of entry capsules used for Mars missions. Models of the deployment, inflation, and aerodynamic performance of the parachutes are necessary to design key aspects of the experiment, including: determining the expected loads and applicable margins on the parachute and payload; guiding sensor selection and placement; evaluating the vehicle trajectory for targeting, range safety, and recovery operations. In addition, knowledge of the differences in the behavior of the parachutes in the wake of slender and blunt bodies is required in order to interpret the results of the sounding rocket experiment and determine how they relate to expected performance behind blunt bodies at Mars. However, modeling the performance of a supersonic DGB in the wake of a slender body is challenging due to the scarcity of historical test data and modeling precedents. This paper describes the models of the aerodynamic performance of DGBs in supersonic slender-body wakes being developed for the ASPIRE sounding rocket test campaign. Development of these models is based on the four available flight tests of DGBs deployed in supersonic slender-body wakes as well as on data from past flight and wind-tunnel experiments of DGBs deployed in the wake of blunt bodies, on the reconstructed at-Mars DGB performance during past missions, and on computational fluid dynamics simulations. Simulations of the wakes of blunt and slender bodies in supersonic flow have been conducted in order to investigate the differences in the flowfields encountered by parachutes deployed in both wake types. The simulations have allowed the project to investigate the fundamental differences between the sounding rocket tests and the flight of a DGB during a Mars mission and to assess the limitations of the sounding rocket test architecture for evaluating flight performance at Mars.

Clark, Ian G.↗
NASA NTRS1995

Minimum fuel mode evaluation

The minimum fuel mode of the NASA F-15 research aircraft is designed to minimize fuel flow while maintaining constant net propulsive force (FNP), effectively reducing thrust specific fuel consumption (TSFC), during cruise flight conditions. The test maneuvers were at stabilized flight conditions. The aircraft test engine was allowed to stabilize at the cruise conditions before data collection initiated; data were then recorded with performance seeking control (PSC) not-engaged, then data were recorded with the PSC system engaged. The maneuvers were flown back-to-back to allow for direct comparisons by minimizing the effects of variations in the test day conditions. The minimum fuel mode was evaluated at subsonic and supersonic Mach numbers and focused on three altitudes: 15,000; 30,000; and 45,000 feet. Flight data were collected for part, military, partial, and maximum afterburning power conditions. The TSFC savings at supersonic Mach numbers, ranging from approximately 4% to nearly 10%, are in general much larger than at subsonic Mach numbers because of PSC trims to the afterburner.

Orme, John S.↗
NASA NTRSDate not supplied

Noise Reduction Trajectory Analysis of a Supersonic Business Jet using Novel Optimization Tools

Proposals to reduce airport noise during takeoff and landing for supersonic aircraft using methods such as variable noise reduction systems add complexity to conceptual flight models. To better optimize these takeoff and landing profiles for noise certification, new modeling methods are explored in this paper with the end goal of more effectively determining the sensitivities of airframe, propulsion, and mission design variables on overall airport noise. Takeoff and landing trajectories are modeled for a notional supersonic business jet concept developed by NASA for use in environmental impact studies conducted by the International Civil Aviation Organization. Optimization tools capable of gradient-based optimal control and collocation solving methods are examined with the aim of achieving faster solutions in a more comprehensive design space. The benefits and limitations of these new methods are compared with existing methods used in previous studies of the airplane concept. It is found that the new modeling methods match closely when compared with existing tools for a standard takeoff and landing case, with a cumulative effective perceived noise difference of 0.1 EPNdB. Comparisons between takeoff trajectories with a variable noise reduction system match within 0.8 EPNdB and 1.3 EPNdB, due to highlighted differences in the modeling approaches.

supersonic↗
NASA NTRS1973

Potential of hydrogen fuel for future air transportation systems.

Recent studies have shown that hydrogen fuel can yield spectacular improvements in aircraft performance in addition to its more widely discussed environmental advantages. The characteristics of subsonic, supersonic, and hypersonic transport aircraft using hydrogen fuel are discussed, and their performance and environmental impact are compared to that of similar aircraft using conventional fuel. The possibilities of developing hydrogen-fueled supersonic and hypersonic vehicles with sonic boom levels acceptable for overland flight are also explored.

Small, W. J.↗
NASA NTRS1991

Turbofan engine demonstration of sensor failure detection

In the paper, the results of a full-scale engine demonstration of a sensor failure detection algorithm are presented. The algorithm detects, isolates, and accommodates sensor failures using analytical redundancy. The experimental hardware, including the F100 engine, is described. Demonstration results were obtained over a large portion of a typical flight envelope for the F100 engine. They include both subsonic and supersonic conditions at both medium and full, nonafter burning, power. Estimated accuracy, minimum detectable levels of sensor failures, and failure accommodation performance for an F100 turbofan engine control system are discussed.

Merrill, Walter C.↗
NASA NTRS1992

Plans for in-flight measurement of hypersonic crossflow transition on the Pegasus launch vehicle

A flight measurements program is underway to obtain flight data for validating stability theory-based transition estimation techniques for crossflow-induced boundary-layer transition at Mach 6-8. A smooth wing glove, designed to enhance crossflow transition and suppress Tollmien-Schlichting (T-S) instabilities, will be mounted on the delta wing of the first stage of the Pegasus booster. The instrumentation package will include 'intelligent' software capable of yielding space and time-correlations obtained through extensive use of fast Fourier transforms (FFTs), 'windowing' and multistage compression as well as a variety of techniques for quality assurance. The flight experiment covers a Mach number range (6 to 8) where low background disturbance data cannot currently be obtained in ground facilities. These flight results will support transition estimation code development for application to supersonic laminar flow control (LFC) and National Aero-Space Plane (NASP) class vehicles in areas where crossflow, rather than T-S waves, is the dominant instability mode.

Bertelrud, Arild↗
NASA NTRS1996

Rocket-Based Combined Cycle Engine Technology Development: Inlet CFD Validation and Application

A CFD methodology has been developed for inlet analyses of Rocket-Based Combined Cycle (RBCC) Engines. A full Navier-Stokes analysis code, NPARC, was used in conjunction with pre- and post-processing tools to obtain a complete description of the flow field and integrated inlet performance. This methodology was developed and validated using results from a subscale test of the inlet to a RBCC 'Strut-Jet' engine performed in the NASA Lewis 1 x 1 ft. supersonic wind tunnel. Results obtained from this study include analyses at flight Mach numbers of 5 and 6 for super-critical operating conditions. These results showed excellent agreement with experimental data. The analysis tools were also used to obtain pre-test performance and operability predictions for the RBCC demonstrator engine planned for testing in the NASA Lewis Hypersonic Test Facility. This analysis calculated the baseline fuel-off internal force of the engine which is needed to determine the net thrust with fuel on.

DeBonis, J. R.↗
NASA NTRS2016

Space Launch System Base Heating Test: Environments and Base Flow Physics

The NASA Space Launch System (SLS) vehicle is composed of four RS-25 liquid oxygen-hydrogen rocket engines in the core-stage and two 5-segment solid rocket boosters and as a result six hot supersonic plumes interact within the aft section of the vehicle during flight. Due to the complex nature of rocket plume-induced flows within the launch vehicle base during ascent and a new vehicle configuration, sub-scale wind tunnel testing is required to reduce SLS base convective environment uncertainty and design risk levels. This hot-fire test program was conducted at the CUBRC Large Energy National Shock (LENS) II short-duration test facility to simulate flight from altitudes of 50 kft to 210 kft. The test program is a challenging and innovative effort that has not been attempted in 40+ years for a NASA vehicle. This paper discusses the various trends of base convective heat flux and pressure as a function of altitude at various locations within the core-stage and booster base regions of the two-percent SLS wind tunnel model. In-depth understanding of the base flow physics is presented using the test data, infrared high-speed imaging and theory. The normalized test design environments are compared to various NASA semi-empirical numerical models to determine exceedance and conservatism of the flight scaled test-derived base design environments. Brief discussion of thermal impact to the launch vehicle base components is also presented.

Mehta, Manish↗
NASA NTRS2017

Computational and Experimental Characterization of the Mach 6 Facility Nozzle Flow for the Enhanced Injection and Mixing Project at NASA Langley Research Center

Computational fluid dynamics analyses and experimental data are presented for the Mach 6 facility nozzle used in the Arc-Heated Scramjet Test Facility for the Enhanced Injection and Mixing Project (EIMP). This project, conducted at the NASA Langley Research Center, aims to investigate supersonic combustion ramjet (scramjet) fuel injection and mixing physics relevant to flight Mach numbers greater than 8. The EIMP experiments use a two-dimensional Mach 6 facility nozzle to provide the high-speed air simulating the combustor entrance flow of a scramjet engine. Of interest are the physical extent and the thermodynamic properties of the core flow at the nozzle exit plane. The detailed characterization of this flow is obtained from three-dimensional, viscous, Reynolds-averaged simulations. Thermodynamic nonequilibrium effects are also investigated. The simulations are compared with the available experimental data, which includes wall static pressures as well as in-stream static pressure, pitot pressure and total temperature obtained via in-stream probes positioned just downstream of the nozzle exit plane.

Drozda, Tomasz G.↗
NASA NTRS1951

Preliminary Investigation of a New Type of Supersonic Inlet

A supersonic inlet with supersonic deceleration of the flow entirely outside of the inlet is considered. A particular arrangement with fixed geometry having a central body with a circular annular intake is analyzed, and it is shown theoretically that this arrangement gives high pressure recovery for a large range of Mach number and mass flow and therefore is practical for use on supersonic airplanes and missiles. For some Mach numbers the drag coefficient for this type of inlet is larger than the drag coefficient for the type of inlet with supersonic compression entirely inside, but the pressure recovery is larger for all flight conditions. The differences in drag can be eliminated for the design Mach number. Experimental results confirm the results of the theoretical analysis and show that pressure recoveries of 95 percent for Mach numbers of 1.33 and 1.52, 92 percent for a Mach number of 1.72, and 86 percent for a Mach number of 2.10 are possible, with the configurations considered. If the mass flow decreases, the total drag coefficient increases gradually and the pressure recovery does not change appreciably. The results of this work were first presented in a classified document issued in 1946.

DIFFUSERS, SUPERSONIC↗
NASA NTRS1992

Some effects of wing and body geometry on the aerodynamic characteristics of configurations designed for high supersonic Mach numbers

Experimental and theoretical results are presented for a family of aerodynamic configurations for flight Mach numbers as high as Mach 8. All of these generic configurations involved 70-deg sweep delta planform wings of three different areas and three fuselage shapes with circular-to-elliptical cross sections. It is noted that fuselage ellipticity enhances lift-curve slope and maximum L/D, while decreasing static longitudinal stability (especially with smaller wing areas).

Spearman, M. L.↗
NASA NTRS1993

Stability of hypersonic boundary-layer flows with chemistry

The effects of nonequilibrium chemistry and three dimensionality on the stability characteristics of hypersonic flows are discussed. In two-dimensional (2-D) and axisymmetric flows, the inclusion of chemistry causes a shift of the second mode of Mack to lower frequencies. This is found to be due to the increase in size of the region of relative supersonic flow because of the lower speeds of sound in the relatively cooler boundary layers. Although this shift in frequency is present in both the equilibrium and nonequilibrium air results, the equilibrium approximation predicts modes which are not observed in the nonequilibrium calculations (for the flight conditions considered). These modes are superpositions of incoming and outgoing unstable disturbances which travel supersonically relative to the boundary-layer edge velocity. Such solutions are possible because of the finite shock stand-off distance. Their corresponding wall-normal profiles exhibit an oscillatory behavior in the inviscid region between the boundary-layer edge and the bow shock. For the examination of three-dimensional (3-D) effects, a rotating cone is used as a model of a swept wing. An increase of stagnation temperature is found to be only slightly stabilizing. The correlation of transition location (N = 9) with parameters describing the crossflow profile is discussed. Transition location does not correlate with the traditional crossflow Reynolds number. A new parameter that appears to correlate for boundary-layer flow was found. A verification with experiments on a yawed cone is provided.

Reed, Helen L.↗
NASA NTRS1992

Status of F16XL SSLFC numerical design validation

The viewgraphs and discussion of the status of the F-16XL SSLFC numerical design validation are provided. The F-16XL Supersonic Laminar Flow Control Program (SSLFC) is a joint effort involving Rockwell's North American Aircraft Division, NASA Ames-Dryden Flight Research Facility, and NASA Langley Research Center. The objectives of the program are to demonstrate that laminar flow can be obtained on a highly swept wing at supersonic speeds, validate the capabilities of a numerical methodology designed to predict boundary layer transition, and validate the capabilities of the methodology in the design of active and passive laminar flow control (LFC) concepts. The F-16XL SSLFC Program consists of the design, fabrication, installation, and flight test of an active laminar flow control glove for the F-16XL. The glove design emphasized the active (suction) control of attachment line and crossflow boundary condition instabilities. The glove design envelop was constrained by the existing geometry, safety of flight considerations, and space requirements for the suction mechanism. The leading edge extension of the glove was limited to 10 inches for consideration of asymmetric flying qualities and the glove height above the existing surface restricted to two inches. The active (suction) portion of the wing extends to nominally 25 percent chord. The glove was constructed of a micro-perforated titanium sheet (hole diameter = 0.025 inches, spacing ratio = 1/8, and sheet thickness = 0.0025 inches). The glove design includes 22 separate chambers to allow suction variation in the chordwise direction. The F-16XL SSLFC program is currently in the flight test phase.

George, Mike↗
NASA NTRS1994

Shock-tunnel combustor testing for hypersonic vehicles

Proposed configurations for the next generation of transatmospheric vehicles will rely on air breathing propulsion systems during all or part of their mission. At flight Mach numbers greater than about 7 these engines will operate in the supersonic combustion ramjet mode (scramjet). Ground testing of these engine concepts above Mach 8 requires high pressure, high enthalpy facilities such as shock tunnels and expansion tubes. These impulse, or short duration facilities have test times on the order of a millisecond, requiring high speed instrumentation and data systems. One such facility ideally suited for scramjet testing is the NASA-Ames 16-Inch shock tunnel, which over the last two years has completed a series of tests for the NASP (National Aero-Space Plane) program at simulated flight Mach numbers ranging from 12-16. The focus of the experimental programs consisted of a series of classified tests involving a near-full scale hydrogen fueled scramjet combustor model in the semi-free jet method of engine testing whereby the compressed forebody flow ahead of the cowl inlet is reproduced (see appendix A). The AIMHYE-1 (Ames Integrated Modular Hypersonic Engine) test entry for the NASP program was completed in April 1993, while AIMHYE-2 was completed in May 1994. The test entries were regarded as successful, resulting in some of the first data of its kind on the performance of a near full scale scramjet engine at Mach 12-16. The data was distributed to NASP team members for use in design system verification and development. Due to the classified nature of the hardware and data, the data reports resulting from this work are classified and have been published as part of the NASP literature. However, an unclassified AIAA paper resulted from the work and has been included as appendix A. It contains an overview of the test program and a description of some of the important issues.

Loomis, Mark P.↗
NASA NTRS1973

Flight investigation of acoustic and thrust characteristics of several exhaust nozzles installed on underwing nacelles on an F106 airplane

To determine flyover noise and thrust and to investigate whether flight velocity significantly affects the noise of exhaust nozzles, a series of flight tests was conducted on three different exhaust nozzles of a type suitable for supersonic transport aircraft. The tests were conducted using an F-106B aircraft modified to carry two underwing nacelles, each containing a calibrated turbojet engine. A flyover altitude of 91 meters (300 ft) and a Mach number of 0.4 provided acoustic data that were repeatable to within + or -1.5 PNdB. Flyover results showed that an auxiliary inlet ejector nozzle was the quietest of the nozzles tested; flight velocity appeared to reduce its noise.

Burley, R. R.↗
NASA NTRS2022

Structural Shape Sensing from Strain Data Using the Basis Function Method

An aircraft shape must be measured during flight to implement an active trim shape control, such as an active dihedral control for a highly flexible aircraft with a high-aspect-ratio wing, and an active sonic boom control for a supersonic transport aircraft. A basis function method for linear as well as geometrically nonlinear structural shape sensing is proposed in this study. Basis functions can be mode shapes, linear static deformation shapes, or geometrically nonlinear static deformation shapes. The proposed basis function method is validated using a high-aspect-ratio wing, a swept test plate, and the National Aeronautics and Space Administration Low Boom Flight Demonstration mission X-59 Quiet Supersonic Technology (QueSST) aircraft (Lockheed Martin, Bethesda, Maryland). A large structural deformation of a high-aspect-ratio wing is successfully captured using the proposed basis function method with less than 0.3-percentprediction error at the wing-tip section. The basis function method gives excellent deformation prediction, even with stress concentration. Performance of the basis functions is compared using the X-59 stabilator sample case. In most of the sample load cases, static deformations give a better correlation with the target deformation than do mode shapes. Wing shape sensing with sparse strain data is also demonstrated in this study using the X-59 QueSST aircraft. Predicted structural deformations match reasonably with the target deformations even without strain gauges on some structural components. The predicted deformations have a good match with the target deformations.

Chan-gi Pak↗