Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SAPPHIRE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60

Effect of Mn Concentration on the Structural, optical and Magnetic Properties of GaMnN

The room temperature magnetization of GaMnN films grown by molecular beam epitaxy on (0001) sapphire substrates with Mn concentrations varying from 0 to 9 at. % was found to depend on Mn concentration, with a maximum magnetization found at -3 at. % Mn. High-resolution x-ray diffraction measurements show that the c-plane lattice constant initially decreases with increasing Mn concentration, then increases when the Mn content increases above -3 at. %. This increase is accompanied by a decrease in the full width at half maximum of the rocking curves. Extended x-ray absorption fine structure results indicate that the nonsubstitutional Mn is not present in the form of Ga{sub x}Mn{sub y} clusters and thus is most likely present in the form of an interstitial. Optical absorption measurements show only a slight increase in the band gap for material with 3 at. % Mn, relative to undoped GaN.

36 MATERIALS SCIENCE↗

Correlation between structure and electrical transport in ion-irradiated graphene grown on Cu foils

Graphene grown by chemical vapor deposition and supported on SiO2 and sapphire substrates was studied following controlled introduction of defects induced by 35 keV carbon ion irradiation. Changes in Raman spectra following fluences ranging from 1012 cm-2 to 1015 cm-2 indicate that the structure of graphene evolves from a highly-ordered layer, to a patchwork of disordered domains, to an essentially amorphous film. These structural changes result in a dramatic decrease in the Hall mobility by orders of magnitude while, remarkably, the Hall concentration remains almost unchanged, suggesting that the Fermi level is pinned at a hole concentration near 1x1013 cm-2. A model for scattering by resonant scatterers is in good agreement with mobility measurements up to an ion fluence of 1x1014 cm-2.

36 MATERIALS SCIENCE↗

Improved Characterization of Transmitted Wavefront Error on CADB Epoxy-Free Bonded Solid State Laser Materials

Current state-of-the-art and next generation laser systems - such as those used in the NIF and LIFE experiments at LLNL - depend on ever larger optical elements. The need for wide aperture optics that are tolerant of high power has placed many demands on material growers for such diverse materials as crystalline sapphire, quartz, and laser host materials. For such materials, it is either prohibitively expensive or even physically impossible to fabricate monolithic pieces with the required size. In these cases, it is preferable to optically bond two or more elements together with a technique such as Chemically Activated Direct Bonding (CADB{copyright}). CADB is an epoxy-free bonding method that produces bulk-strength bonded samples with negligible optical loss and excellent environmental robustness. The authors have demonstrated CADB for a variety of different laser glasses and crystals. For this project, they will bond quartz samples together to determine the suitability of the resulting assemblies for large aperture high power laser optics. The assemblies will be evaluated in terms of their transmitted wavefront error, and other optical properties.

42 ENGINEERING↗

Effects of Growth Temperature on Epitaxial Thin Films of Vanadium Dioxide Grown by Pulsed Laser Deposition

Stoichiometric vanadium dioxide in all of its bulk, thin film and nanostructured forms exhibits an insulator-to-metal transition (IMT) accompanied by structural change, induced by various physical and chemical stimuli such as temperature, ultrashort light pulses, electric field, doping or strain. In these applications, the optical qualities of the films are of paramount importance, but are often highly variable depending on fabrication procedure. We have grown epitaxial films of vanadium dioxide on c-plane (0001) of sapphire using two different procedures involving room temperature growth followed by annealing and direct high temperature growth. Strain at the interface of the substrate and the film due to growth at different temperatures leads to significant differences in morphologies and phase transition characteristics. We present a comparative study of the morphologies and switching characteristics of the two films and conclude that contrary to conventional wisdom, the room-temperature grown films have smoother, more continuous morphologies and better switching performance. Our observation is supported by theoretical and experimental studies of epitaxial growth of semiconductors.

36 MATERIALS SCIENCE↗

Solid-solid phase transition measurements in iron

Previously, dynamic experiments on iron have observed a non-zero transition time and width in the solid-solid {alpha}-{var_epsilon} phase transition. Using Proton Radiography at the Los Alamos Neutron Science Center, we have performed plate impact experiments on iron to further study the {alpha}-{var_epsilon} phase transition which occurs at 13GPa. A 40mm bore powder gun was coupled to a proton radiography beam line and imaging system and synchronized to the impact of the projectile on the target sample with the proton beam pattern. A typical experimental configuration for the iron study, as shown below in 3 color-enhanced radiographs, is a 40mm diameter aluminum sabot impacting a 40mm diameter of polycrystalline ARMCO iron. The iron is backed by a sapphire optical window for velocimetry measurements. The aluminum flyer on the left of the iron is barely visible for visual display purposes. Direct density jumps were measured which corresponded to calculations to within 1% using a Wondy mUlti-phase equation of state model. In addition, shock velocities were measured using an edge fitting technique and followed that edge movement from radiograph to radiograph, where radiographs are separated in time by 500 ns. Preliminary measurements give a shock velocity (P1 wave) of 5.251 km/s. The projectile velocity was 0.725 km/s which translate to a peak stress of 17.5 GPa. Assuming the P1 wave is instantaneous, we are able to calibrate the chromatic, motion, object and camera blur by measuring the width of the P1 wave. This approximation works in this case since each of the two density jumps are small compared to the density of the object. Subtracting the measured width of the P1 wave in quadrature from the width of the P2 wave gives a preliminary measurement of the transition length of 265 {mu}m. Therefore, a preliminary measured phase transition relaxation time {tau} = transition length/u{sub s} = 265 {mu}m/5.251 km/s = 50 ns. Both Boettger and Jensen conclude that the transition rate and likely the transition mechanisms depend on the impact stress and the sample thickness. Since Proton Radiography can measure directly the transition length as well as the shock velocity, a transition time can be directly calculated. With higher higher energy protons we have better resolution of the measured width and edge locations. This will allow a more precise measurement of phase transition relaxation time. We propose to perform a series of experiments to measure the phase transition relaxation time, {tau}, as a function of drive and sample size.

36 MATERIALS SCIENCE↗

RF-THERMAL COMBINED SIMULATIONS OF A SUPERCONDUCTING HOM COAXIAL COUPLER

To benchmark a multi-physics code VORPAL developed by Tech-X, the High Order Mode (HOM) coaxial coupler design implemented in Jefferson Lab?s 12GeV upgrade cryomodules is analyzed by use of commercial codes, such as ANSYS, HFSS and Microwave Studio. Testing data from a Horizontal Test Bench (HTB) experiment on a dual-cavity prototype are also utilized in the verification of simulation results. The work includes two stages: first, the HOM feedthrough that has a high RRR niobium probe and sapphire insulator is analyzed for the RF-thermal response when there is travelling wave passing through; second, the HTB testing condition is simulated and results from simulation are compared to thermal measurements from HTB tests. The analyses are of coupled-field nature and involve highly nonlinear temperature dependent thermal conductivities and electric resistivities for the eight types of materials used in the design. Accuracy and efficiency are the main factors in evaluation of the performance of the codes.

43 PARTICLE ACCELERATORS↗

Substrate compliance effects on buckle driven delamination in thin gold film systems.

Film durability is a primary factor governing the use of emerging thin film flexible substrate devices where compressive stresses can lead to delamination and buckling. It is of particular concern in gold film systems found in many submicron and nanoscale applications. We are therefore studying these effects in gold on PMMA systems using compressively stressed tungsten overlayers to force interfacial failure and simulations employing cohesive zone elements to model the fracture process. Delamination and buckling occurred spontaneously following deposition with buckle morphologies that differed significantly from existing model predictions. Moreover, use of thin adhesive interlayers had no discernable effect on performance. In this presentation we will use observations and simulations to show how substrate compliance and yielding affects the susceptibility to buckling of gold films on compliant substrates. We will also compare the fracture energies and buckle morphologies of this study with those of gold films on sapphire substrates to show how changing substrate compliance affects buckle formation.

36 MATERIALS SCIENCE↗

Chip scale mechanical spectrum analyzers based on high quality factor overmoded bulk acouslic wave resonators

The goal of this project was to develop high frequency quality factor (fQ) product acoustic resonators matched to a standard RF impedance of 50 {Omega} using overmoded bulk acoustic wave (BAW) resonators. These resonators are intended to serve as filters in a chip scale mechanical RF spectrum analyzer. Under this program different BAW resonator designs and materials were studied theoretically and experimentally. The effort resulted in a 3 GHz, 50 {Omega}, sapphire overmoded BAW with a fQ product of 8 x 10{sup 13}, among the highest values ever reported for an acoustic resonator.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Kinetics of solid-solid phase transitions in metals using proton radiography (u)

When a compressed material changes phase it doesn't do so instantly. Instead it transitions through a mixed phase as it transforms to the end state phase for a given pressure, volume and temperature. Common phase diagrams show the phase boundaries as sharp lines when compression has been slowly applied and held for an infinite amount of time. When the compression is applied with high strain rate, however, the phase boundaries are no longer crisp as the kinetic effects of the crystal reorientation delay the transitions, resulting in regions of mixed phase. This opens up the possibility that some degree of metastability exists for such transition in dynamic compression. The compression path can go past the equilibrium phase boundary and the transition happen from a metastable state because of the very short timescale of the compression process. Molecular dynamics (MD) simulations recently have been used to examine shock-induced phase transitions in single crystal materials illustrating an orientation dependence of the transition stress, mechanisms, kinetics, and Hugoniot response. For example, the [100] orientation of iron had a simulated transition stress higher than the experimentally determined polycrystalline value of 13 GPa by 2 GPa. Previously, dynamic experiments on iron have observed a non-zero transition time and width in the solid-solid {alpha}-{var_epsilon} phase transition. Using Proton Radiography at the Los Alamos Neutron Science Center, we have performed plate impact experiments on iron to further study the {alpha}-{var_epsilon} phase transition which occurs at 13 GPa. A 40mm bore powder gun was coupled to a proton radiography beam line and imaging system and synchronized to the impact of the projectile on the target sample with the proton beam pattern. A typical experimental configuration for the iron study, as shown below in 3 color-enhanced radiographs, is a 40mm diameter aluminum sabot impacting a 40mm diameter sample of polycrystalline ARMCO iron. The iron is backed by a sapphire optical window for velocimetry measurements. The aluminum flyer on the left of the iron is barely visible for visual display purposes.

36 MATERIALS SCIENCE↗

Kinetics of Solid-Solid Phase Transition in Iron (u)

Previously, dynamic experiments on iron have observed a non-zero transition time and width in the solid-solid {alpha}-{var_epsilon} phase transition. Using Proton Radiography at the los Alamos Neutron Science Center, we have performed plate impact experiments on iron to further study the {alpha}-{var_epsilon} phase transition which occurs at 13GPa. A 40mm bore powder gun was coupled to a proton radiography beam line and imaging system and synchronized to the impact of the projectile on the target sample with the proton beam pattern. A typical experimental configuration for the iron study, as shown below in 3 color-enhanced radiographs, is a 40mm diameter aluminum sabot impacting a 40mm diameter of polycrystalline ARMCO iron. The iron is backed by a sapphire optical window for velocimetry measurements. The aluminum flyer on the left of the iron is barely visible for visual display purposes. Direct density jumps were measured which corresponded to calculations to within 1% using a Wondy multi-phase equation of state model. In addition, shock velocities were measured using an edge fitting technique and followed that edge movement from radiograph to radiograph, where rad iographs are separated in time by 500 ns. Preliminary measurements give a shock velocity (P1 wave) of 5.251 km/s. The projectile velocity was 0.725 km/s which translate to a peak stress of 17.5 GPa. Assuming the P1 wave is instantaneous, we are able to calibrate the chromatic, motion, object and camera blur by measuring the width of the P1 wave. This approximation works in this case since each of the two density jumps are small compared to the density of the object. Subtracting the measured width of the P1 wave in quadrature from the width of the P2 wave gives a preliminary measurement of the transition length of 265 {micro}m. Therefore, a preliminary measured phase transition relaxation time {tau} = transition length/u{sub s} = 265 {micro}m/5.251 km/s = 50 ns. Both Boettger1 & Jensen2 conclude that the transition rate and likely the transition mechanisms depend on the impact stress and the sample thickness. Since Proton Radiography can measure directly the transition length as well as the shock velocity, a transition time can be directly calculated. We propose to perform a series of experiments to measure the phase transition relaxation time, 1, as a function of drive, sample size and crystal orientation.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

BNL 56 MHz HOM Damper Prototype Fabrication at JLab

A prototype Higher-Order Mode (HOM) Damper was fabricated at JLab for the Relativistic Heavy-Ion Collider's (RHIC) 56 MHz cavity at Brookhaven National Laboratory (BNL). Primarily constructed from high RRR Niobium and Sapphire, the coaxial damper presented significant challenges in electron-beam welding (EBW), brazing and machining via acid etching. The results of the prototype operation brought about changes in the damper design, due to overheating braze alloys and possible multi-pacting. Five production HOM dampers are currently being fabricated at JLab. This paper outlines the challenges faced in the fabrication process, and the solutions put in place.

36 MATERIALS SCIENCE↗

State of knowledge and challenges of U-Si compounds for use in light water reactor accident tolerant fuel designs

Characterization of the properties of U-Si compounds first required synthesis of high purity material for each of the compositions. The four compounds targeted for investigation in this work were U{sub 3}Si, U{sub 3}Si{sub 2}, USi, and U{sub 3}Si{sub 5}. Specimens of U{sub 3}Si{sub 2}, U{sub 3}Si{sub 5}, and USi with specific geometries for individual testing procedures were prepared using a powder metallurgical method. Thermophysical properties of the U-Si compounds were determined within 100 K of their respective melt point or decomposition temperature. Thermal expansion was determined with a dilatometer, specific heat capacity by the ratio method in a differential scanning calorimeter using a sapphire standard, while thermal diffusivity was determined with a laser flash analyzer. Oxidation performance of the U-Si compounds was determined in a thermogravimetric analyzer (TGA), which measures the weight change of a sample as a function of gas composition and temperature. The results show that each of the U-Si compounds is electronically conductive leading to higher thermal conductivity values than the reference fuel UO{sub 2}. Higher thermal conductivity values will lead to enhanced safety margins within a reactor core and provide better economics over the lifetime of a fuel cycle. However, no improvements have been realized over the reference UO{sub 2} case with regards to oxidation performance in air although more testing is required to substantiate the differences especially in steam and corrosive aqueous LWR environments. Finally, there exists a lack of knowledge in the literature with regards to low burnup irradiation testing on all of the U-Si binary compounds, which would be necessary to simulate their performance in a reactor setting.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fiber Optic Instrumentation in High Temperature Irradiation Environments

The extremely harsh conditions of advanced reactor designs pose serious challenges for nuclear fuels and materials. Traditional instrumentation (thermocouples, strain gauges, etc.) are not well suited for extended operation in such a harsh environment. This work discusses the potential for using fiber optic-based instrumentation in high temperature irradiation experiments. The primary limitation of fiber optic instrumentation in irradiation experiments is signal darkening due to attenuation in the fiber material. A computational model has been developed to predict broadband optical attenuation in fused silica fiber materials as a function of time, temperature, and dose. Preliminary results obtained using this model are shown for one cycle of irradiation in the high flux isotope reactor at various temperatures. An irradiation campaign has been initiated to provide temperature-dependent optical attenuation data at high dose in order to validate the predictive model. Demonstration of the safety and reliability of new and enhanced nuclear fuels and materials is essential for improving the safety and reliability of existing nuclear power plants and for the licensing and operation of advanced nuclear reactor technologies. Experimental validation of fuel performance codes requires high fidelity measurements during instrumented irradiation experiments. Therefore, a clear need exists for sensors of unprecedented accuracy, resolution, time/space/energy spectrum dependence, reduced size, and, perhaps most importantly, performance in harsh environments. The harsh environment during accelerated irradiation testing could include temperatures from 300 deg. C up to 2600 deg. C, and radiation damage levels ranging from 1 to greater than 100 dpa. Optical fiber-based sensors are a promising candidate for instrumentation in high temperature irradiation environments. Optical fibers are small, inexpensive, chemically inert, immune to electromagnetic interference, and made of high temperature radiation-hard materials. The ability to make distributed measurements of temperature or strain using a single inexpensive optical fiber currently exists for non-extreme environments as commercially available technology. Other advanced sensing technologies such as laser ultrasound, borescopes, and laser-induced breakdown spectroscopy use fiber optic light delivery as a critical component of the sensor design. Some potential applications for optical fiber-based sensors in instrumented irradiation experiments include in-situ measurements of thermal conductivity, ultrasonic measurement of elastic constants (with fiber optic delivery of signal for generation and detection of ultrasonic wave), and distributed measurements of temperature and/or strain (i.e., swelling). The primary limitation for the use of optical technologies for harsh environment (e.g., high neutron flux reactor environments) instrumentation is the attenuation of the light signal due to the effects of temperature and/or irradiation. This work summarizes initial efforts towards developing a predictive model of temperature-dependent radiation-induced attenuation in fused silica optical fibers at high dose. If there is adequate transmission in the fibers, fiber optic-based instrumentation could provide highly accurate distributed measurements during instrumented fuel/material irradiation experiments. Preliminary results show attenuation on the order of 5- 10 dB/m in the wavelength range of 750-900 nm at temperatures of 300 deg. C and below after one HFIR cycle (24 days). At higher temperatures (600 and 900 deg. C), the attenuation is reduced below 5 dB/m in the same wavelength range. This amount of attenuation is acceptable for most fiber optic based sensor systems with a dynamic range on the order of 20-50 dB for a reasonable length (1-2 meters) of fiber in the high flux region. Many optical components use a wavelength of 850 nm, which lies in the low attenuation window. In order to refine and ultimately validate the predictive model of optical fiber attenuation, a reactor irradiation campaign has been initiated. Rabbit irradiation capsules have been designed to irradiate optical fiber material (low and high OH fused silica, as well as single crystal sapphire) specimens in the HFIR at temperatures ranging from 100 to 1200 deg. C. (authors)

42 ENGINEERING↗

Investigation of Coded Source Neutron Imaging at the North Carolina State University PULSTAR Reactor

A neutron imaging facility is located on beam-tube #5of the 1-MWth PULSTAR reactor at the North Carolina StateUniversity. An investigation has been initiated to explore theapplication of coded imaging techniques at the facility. Codedimaging uses a mosaic of pinholes to encode an aperture, thusgenerating an encoded image of the object at the detector. Toreconstruct the image recorded by the detector, correspondingdecoding patterns are used. The optimized design of coded masksis critical for the performance of this technique and will dependon the characteristics of the imaging beam. In this work, MonteCarlo (MCNP) simulations were utilized to explore the neededmodifications to the PULSTAR thermal neutron beam to supportcoded imaging techniques. In addition, an assessment of codedmask design has been performed. The simulations indicated thata 12 inch single crystal sapphire filter is suited for such anapplication at the PULSTAR beam in terms of maximizing fluxwith good neutron-to-gamma ratio. Computational simulationsdemonstrate the feasibility of correlation reconstruction methodson neutron transmission imaging. A gadolinium aperture withthickness of 500 m was used to construct the mask using a 38 ×34 URA pattern. A test experiment using such a URA design hasbeen conducted and the point spread function of the system hasbeen measured.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Application of a four-step HMX kinetic model to an impact-induced fraction ignition problems

There has been a long history of interest in the decomposition kinetics of HMX and HMX-based formulations due to the widespread use of this explosive in high performance systems. The kinetics allow us to predict, or attempt to predict, the behavior of the explosive when subjected to thermal hazard scenarios that lead to ignition via impact, spark, friction or external heat. The latter, commonly referred to as 'cook off', has been widely studied and contemporary kinetic and transport models accurately predict time and location of ignition for simple geometries. However, there has been relatively little attention given to the problem of localized ignition that results from the first three ignition sources of impact, spark and friction. The use of a zero-order single-rate expression describing the exothermic decomposition of explosives dates to the early work of Frank-Kamanetskii in the late 1930s and continued through the 60's and 70's. This expression provides very general qualitative insight, but cannot provide accurate spatial or timing details of slow cook off ignition. In the 70s, Catalano, et al., noted that single step kinetics would not accurately predict time to ignition in the one-dimensional time to explosion apparatus (ODTX). In the early 80s, Tarver and McGuire published their well-known three step kinetic expression that included an endothermic decomposition step. This scheme significantly improved the accuracy of ignition time prediction for the ODTX. However, the Tarver/McGuire model could not produce the internal temperature profiles observed in the small-scale radial experiments nor could it accurately predict the location of ignition. Those factors are suspected to significantly affect the post-ignition behavior and better models were needed. Brill, et al. noted that the enthalpy change due to the beta-delta crystal phase transition was similar to the assumed endothermic decomposition step in the Tarver/McGuire model. Henson, et al., deduced the kinetics and thermodynamics of the phase transition, providing Dickson, et al. with the information necessary to develop a four-step model that included a two-step nucleation and growth mechanism for the {beta}-{delta} phase transition. Initially, an irreversible scheme was proposed. That model accurately predicted the spatial and temporal cook off behavior of the small-scale radial experiment under slow heating conditions, but did not accurately capture the endothermic phase transition at a faster heating rate. The current version of the four-step model includes reversibility and accurately describes the small-scale radial experiment over a wide range of heating rates. We have observed impact-induced friction ignition of PBX 9501 with grit embedded between the explosive and the lower anvil surface. Observation was done using an infrared camera looking through the sapphire bottom anvil. Time to ignition and temperature-time behavior were recorded. The time to ignition was approximately 500 microseconds and the temperature was approximately 1000 K. The four step reversible kinetic scheme was previously validated for slow cook off scenarios. Our intention was to test the validity for significantly faster hot-spot processes, such as the impact-induced grit friction process studied here. We found the model predicted the ignition time within experimental error. There are caveats to consider when evaluating the agreement. The primary input to the model was friction work over an area computed by a stress analysis. The work rate itself, and the relative velocity of the grit and substrate both have a strong dependence on the initial position of the grit. Any errors in the analysis or the initial grit position would affect the model results. At this time, we do not know the sensitivity to these issues. However, the good agreement does suggest the four step kinetic scheme may have universal applicability for HMX systems.

36 MATERIALS SCIENCE↗

Visualizing Energy Transfer at Buried Interfaces in Layered Materials Using Picosecond X-Rays

Understanding the fundamentals of nanoscale heat propagation is crucial for next-generation electronics. For instance, weak van der Waals bonds of layered materials are known to limit their thermal boundary conductance (TBC), presenting a heat dissipation bottleneck. In this paper we present a new non-destructive method to probe heat transport in nanoscale crystalline materials using time-resolved x-ray measurements of photo-induced thermal strain. This technique directly monitors time-dependent temperature changes in the crystal and the subsequent relaxation across buried interfaces by measuring changes in the c-axis lattice spacing after optical excitation. We investigate films of five different layered transition metal dichalcogenides MoX 2 [X= S, Se, Te] and WX 2 [X= S, Se] as well as graphite and a W-doped alloy of MoTe 2 , on c-plane sapphire substrates, finding TBC values in the range 10-30 MWm -2 K -1 at room temperature. In conjunction with molecular dynamics simulations, we show that the high thermal resistances are a consequence of weak interfacial van der Waals bonding and low phonon irradiance. This work paves the way for an improved understanding of thermal bottlenecks in emerging three-dimensional heterogeneously integrated technologies.

36 MATERIALS SCIENCE↗

Controlled Growth of Single‐Crystal Graphene Wafers on Twin‐Boundary‐Free Cu(111) Substrates

Single-crystal graphene (SCG) wafers are needed to enable mass-electronics and optoelectronics owing to their excellent properties and compatibility with silicon-based technology. Controlled synthesis of high-quality SCG wafers can be done exploiting single-crystal Cu(111) substrates as epitaxial growth substrates recently. However, current Cu(111) films prepared by magnetron sputtering on single-crystal sapphire wafers still suffer from in-plane twin boundaries, which degrade the SCG chemical vapor deposition. Here, in this study, it is shown how to eliminate twin boundaries on Cu and achieve 4 in. Cu(111) wafers with ≈95% crystallinity. The introduction of a temperature gradient on Cu films with designed texture during annealing drives abnormal grain growth across the whole Cu wafer. In-plane twin boundaries are eliminated via migration of out-of-plane grain boundaries. SCG wafers grown on the resulting single-crystal Cu(111) substrates exhibit improved crystallinity with >97% aligned graphene domains. As-synthesized SCG wafers exhibit an average carrier mobility up to 7284 cm 2 V −1 s −1 at room temperature from 103 devices and a uniform sheet resistance with only 5% deviation in 4 in. region.

36 MATERIALS SCIENCE↗

Engineering Electrical Transport by Implantation‐Induced Defects in CrN Films Without Affecting Thermal Conductivity

The transport properties of CrN thin films deposited on sapphire have been tailored through structural modifications induced by cumulative argon implantation. As-grown samples experience the typical structural transition in CrN films from orthorhombic at low temperature to cubic above the Néel temperature (≈280 K) and exhibit a metallic-like conduction in both phases. With increasing implantation dose, the conduction mode shifts to a semiconductor-like behavior in both phases, albeit at different damage levels. Analysis of the results suggests that hopping conduction becomes dominant beyond a given damage threshold. The results highlight a promising correlation between defect engineering and conduction mechanisms, offering valuable insights into the versatile electrical properties of CrN films. These implantation-induced defects scatter carriers, leading to a decrease in their mobility. As the implantation dose increases, the defect landscape evolves, modifying the density of states. However, up to a dose of 0.050 dpa, no significant influence on phonon scattering is observed. This approach demonstrates that ion implantation enables precise tuning of CrN's electrical properties without affecting thermal conductivity, offering valuable insights into defect engineering in transition metal nitrides and underscoring its potential for transport properties decorrelation.

defects↗