Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Route optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,081 records · Page 60
All sourcesNASA NTRSDOE OSTI
DOE OSTI2014

Comparative assessment of municipal sewage sludge incineration, gasification and pyrolysis for a sustainable sludge-to-energy management in Greece

Highlights: • The high output of MSS highlights the need for alternative routes of valorization. • Evaluation of 3 sludge-to-energy valorisation methods through SWOT analysis. • Pyrolysis is an energy and material recovery process resulting to ‘zero waste’. • Identification of challenges and barriers for MSS pyrolysis in Greece was investigated. • Adopters of pyrolysis systems face the challenge of finding new product markets. - Abstract: For a sustainable municipal sewage sludge management, not only the available technology, but also other parameters, such as policy regulations and socio-economic issues should be taken in account. In this study, the current status of both European and Greek Legislation on waste management, with a special insight in municipal sewage sludge, is presented. A SWOT analysis was further developed for comparison of pyrolysis with incineration and gasification and results are presented. Pyrolysis seems to be the optimal thermochemical treatment option compared to incineration and gasification. Sewage sludge pyrolysis is favorable for energy savings, material recovery and high added materials production, providing a ‘zero waste’ solution. Finally, identification of challenges and barriers for sewage sludge pyrolysis deployment in Greece was investigated.

09 BIOMASS FUELS↗
DOE OSTI2016

Coarse-grained models using local-density potentials optimized with the relative entropy: Application to implicit solvation

Bottom-up multiscale techniques are frequently used to develop coarse-grained (CG) models for simulations at extended length and time scales but are often limited by a compromise between computational efficiency and accuracy. The conventional approach to CG nonbonded interactions uses pair potentials which, while computationally efficient, can neglect the inherently multibody contributions of the local environment of a site to its energy, due to degrees of freedom that were coarse-grained out. This effect often causes the CG potential to depend strongly on the overall system density, composition, or other properties, which limits its transferability to states other than the one at which it was parameterized. Here, we propose to incorporate multibody effects into CG potentials through additional nonbonded terms, beyond pair interactions, that depend in a mean-field manner on local densities of different atomic species. This approach is analogous to embedded atom and bond-order models that seek to capture multibody electronic effects in metallic systems. We show that the relative entropy coarse-graining framework offers a systematic route to parameterizing such local density potentials. We then characterize this approach in the development of implicit solvation strategies for interactions between model hydrophobes in an aqueous environment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Optimized oxygen deprived low temperature sputtered WO3 thin films for crystalline structures

In this work, we report a detailed analysis on the effects of processing parameters for sputtered tungsten trioxide (WO 3 ) thin nanoscale films on their structural, vibrational and electrical properties. The research aims to understand the fundamental aspects of WO3 sputtering at relatively low temperatures and in an oxygen deprived environment targeting applications of temperature and oxygen sensitive substrates. Structural analysis indicates that films deposited at room temperature, or substrate temperatures at or below 400 degrees C with low oxygen partial pressure are amorphous. Furthermore, crystallization of the films was observed with distinct Raman peaks when the films were annealed at 300 degrees C or above using rapid thermal annealing for 10 min. Films revealed monoclinic phases of WO 3 with the presence of W-O-W stretching, bending and lattice vibrational modes in the Raman spectra. Interestingly, a change of transport behavior from insulating to semiconducting was observed for as deposited films on post annealing. Annealed films revealed stoichiometric WO 3 phases with no external defects detected. The present study adopts a route to intercalate WO 3 in a variety of applications from electrochromic coloration to a nanocrystalline thin film for electronic devices sensitive to higher temperatures and gas flow in the sputtering system.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2022

SOMAS: a platform for data-driven material discovery in redox flow battery development

Abstract Aqueous organic redox flow batteries offer an environmentally benign, tunable, and safe route to large-scale energy storage. The energy density is one of the key performance parameters of organic redox flow batteries, which critically depends on the solubility of the redox-active molecule in water. Prediction of aqueous solubility remains a challenge in chemistry. Recently, machine learning models have been developed for molecular properties prediction in chemistry and material science. The fidelity of a machine learning model critically depends on the diversity, accuracy, and abundancy of the training datasets. We build a comprehensive open access organic molecular database “Solubility of Organic Molecules in Aqueous Solution” (SOMAS) containing about 12,000 molecules that covers wider chemical and solubility regimes suitable for aqueous organic redox flow battery development efforts. In addition to experimental solubility, we also provide eight distinctive quantum descriptors including optimized geometry derived from high-throughput density functional theory calculations along with six molecular descriptors for each molecule. SOMAS builds a critical foundation for future efforts in artificial intelligence-based solubility prediction models.

25 ENERGY STORAGE↗
DOE OSTI2022

Custom-designed heat treatment simultaneously resolves multiple challenges facing 3D-printed single-crystal superalloys

Single-crystal Ni-based superalloys are currently the material of choice for turbine blade applications, especially with the emerging additive manufacturing (AM) that facilitates the manufacture/repair of these single crystals. This promising AM route, however, comes with a dilemma: in the fusion and heat affected zones after e-beam or laser induced melting, one needs a solutionizing annealing to relieve the residual stresses and homogenize the chemical/microstructure. The super-solvus solutionizing temperature is usually adopted from the protocol for the cast superalloys, which almost always causes recrystallization and stray grain growth, resulting in a polycrystalline microstructure and degrading the high-temperature mechanical performance. Here, in this paper, we demonstrate a custom-designed post-printing heat treatment to replace the conventional super-solvus one. The recovery and relatively low temperature diminish the driving force for recrystallization and the movement of stray grain boundaries, without suffocating the chemical/microstructural homogenization thanks to the narrow dendrite width and short element segregation distance. The optimal duration of the heat treatment is proposed to achieve atomic-diffusion mediated chemical homogenization while limiting γ'-particle coarsening in the interdendritic regions. Our strategy makes it practically feasible to resolve several bottleneck problems with one processing/treatment, removing a seemingly formidable obstacle to effective additive manufacturing of superalloy single crystal products.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hydrogen Localization and Cluster Formation in α-Zr from First-Principles Investigations

We report alpha-zirconium (α-Zr) is a hydrogen atom host material used in nuclear energy and semiconducting applications due to Zr's excellent properties such as corrosion resistance, low thermal neutrons cross-section, and thermodynamically favorable interstitial sequestering of H atoms. Herein we use density functional theory simulations to systematically analyze the initial stages of H insertion in the Zr matrix, and determine optimal hydrogen localization, distribution, and clustering tendencies from a thermodynamics and kinetics perspective. Our results suggest that H occupation of tetrahedral sites is strongly favored, consistent with previous experimental and theoretical studies. Further, a cooperative effect in H localization is shown where H atoms favor clustering. The H pair is found to be the most stable by occupying tetrahedral sites with pairs at second nearest-neighbor positions (TTn2). Among the four H atom clusters, the most favorable configuration has two TTn2 pairs forming "box " or "zig-zag" shaped-cluster with the pairs separated by 3.03 or 3.25 Å, respectively. Nudged elastic band simulations suggest that the formation of TTn2 is facile and is limited by the small diffusion barrier of the monomer of less than 0.1 eV. Further, the formation routes for the 4H atom clusters are also presented. The current study can serve as a foundation to systematically model H atom clustering in metals and alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Irradiation route to aqueous synthesis of highly luminescent ZnSe quantum dots and its function as a copper ion fluorescence sensor

Highlights: • Radiation chemical technique can provide a useful route for synthesis of ZnSe QDs. • Chelating nature of ethylene diamine is exploited for capping nanoparticles. • ZnSe QDs can be a suitable sensitive alternative to toxic cadmium-based system. • Cu(II) ion is probed by QDs in the presence of other physiologically relevant ions. - Abstract: Size-controlled synthesis of stable ZnSe QDs with narrow distribution in aqueous environment through conventional soft chemical method still poses a challenge. The proposed radiation assisted strategy demonstrates aqueous synthesis of stable, monodisperse and luminescent ZnSe QDs capped with chelating ethylene diamine under ambient conditions and at room temperature. Radiation chemical method facilitates in slow and in-situ release of selenium ion from sodium selenosulfate. The concentrations of precursors, such as zinc salt, selenium source, ethylene diamine and absorbed radiation (7–90 kGy) dose were optimized for obtaining good quality particles. Selective quenching of luminescence of as-synthesized quantum dots (QDs) by Cu{sup 2+} ions vis-à-vis other physiologically important cations provide evidence for use of ZnSe quantum dots as alternative to toxic Cd-based quantum dots to probe Cu{sup 2+} ions. The linear relation of ratio of loss in emission intensity as a function of concentration of Cu(II) indicates detection limit in nano-molar range.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Tailoring low energy electron absorption via surface nano-engineering of cesiated chromium films

Here, we demonstrate that improved low energy electron absorption is achieved by suppressing the crystallinity of chromium thin-films grown on W[110], which points to a promising route for achieving highly efficient thermionic energy converters. Using low energy electron microscopy (LEEM) and in situ film growth, we show that substrate temperature control permits well-controlled fabrication of either epitaxial Cr[110] films or nanocrystalline Cr layers. We show that the work function of cesium saturated nanocrystalline Cr thin-films is ~0.20 eV lower than that of epitaxial Cr[110] films. Our LEEM measurements of absorbed and reflected currents as a function of electron energy demonstrate that nanocrystallinity of cesiated chromium films results in 96% electron absorption in the range up to 1 eV above the work function, compared to just 79% absorption in cesiated crystalline Cr[110] films. These results point to metal films with suppressed crystallinity as an economical and scalable means to synthesize nanoengineered surfaces with optimized properties for next generation anode materials in high performance thermionic energy converters.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

Topical Report – Findings on Subtask 2.7 – Wet ESP and Aerosol Testing at Coal Creek Station

Growing concerns over the impact of CO 2 emissions from combustion sources on global climate change have prompted numerous research and development projects aimed at developing cost-effective technologies for CO 2 capture. One family of technologies being demonstrated at pilot and full scale globally is postcombustion carbon capture (PCCC) systems that employ amine-based solvents. The captured CO 2 can be compressed and permanently stored underground or used for enhanced oil recovery. The proximity of North Dakota’s lignite-fired fleet of power plants to potential CO 2 storage options creates a unique atmosphere for PCCC within the state. However, the unique components present in lignite flue gas present a challenge for large-scale PCCC at North Dakota power plants by contributing to aerosol formation. Aerosols can negatively impact the long-term performance of amine-based solvents for CO 2 capture. Amine-based solvents are volatile, and flue gas particulate provides nucleation sites where amine vapors can condense as aerosols. Because aerosols cannot be easily captured at the column outlet using conventional technologies, the amine-laden aerosols escape the system and lead to accelerated solvent losses. Moreover, particulate components can chemically react with amines to form degradation products that can permanently deactivate the amine, cause fouling, and lead to hazardous emissions. Many of the elements that have been shown to catalyze solvent degradation are present in lignite coals and can exacerbate solvent replacement economics. Understanding this issue is critical to the implementation of solvent-based CO 2 capture systems as applied to lignite-fired generation systems. The Energy & Environmental Research Center (EERC) designed and carried out this project to fully characterize aerosol behavior with various control technologies installed to better optimize aerosol mitigation technology for CO 2 capture. To meet the goal of this project, the following objectives were identified: Determine the effectiveness of a wet electrostatic precipitator (WESP) on mitigating formation of problematic aerosols at Great River Energy’s Coal Creek Station, upstream of the PCCC system. Determine the effectiveness of the Mitsubishi Heavy Industries (MHI) proprietary amine emission reduction unit (AERU) as a postcapture solvent recovery system for reducing aerosol emissions and extending solvent life downstream of the PCCC system. Determine the impact of aerosols on the efficiency and degradation products of both commercial and advanced solvents within the PCCC system. Work was conducted at Coal Creek Station Unit 1 using a slipstream of flue gas from the outlet of the plant’s flue gas desulfurization (FGD) unit. Flue gas was routed through a pilot-scale FGD unit to remove SO 2 to very low levels (~1 ppm) and then through a direct contact cooler (DCC) to further cool the gas and to remove moisture. The gas exiting the DCC was then optionally routed through a WESP before passing to the CO 2 absorber columns. The MHI solvent was used to scrub CO 2 from the slipstream through a set of two absorber columns. The rich solvent was regenerated in a stripper column by heating to drive off captured CO 2 . Flue gas exiting the absorber column was routed to MHI’s proprietary AERU to recover entrained solvent. The system operated using a catch-and-release method where the CO 2 was separated to provide data on the process, but the captured CO 2 was released back into the host site stack. Particulate was measured, collected, and analyzed from multiple locations throughout the pilot-scale system. Unlike the performance observed in prior work, the inlet FGD and DCC did not remove significant particulate matter from the flue gas. This appears to be due to a difference in the nature of the particulate. The DCC seemed to increase particulate size and count, most likely owing to water condensing onto the surfaces of fly ash particles. When the WESP was operated, it achieved >95% particulate capture. Very little particulate matter or indications of solvent were detected at the AERU outlet. When operating with advanced KS 21 solvent, the particulate material at the AERU outlet was even further decreased. Solvent analysis showed that some species derived from flue gas and ash were slowly concentrating in the solvent over the duration of the test. The levels observed were reported to be within expected ranges and were not of concern to MHI. A high-level techno-economic assessment of installing CO 2 capture at Coal Creek Station suggested that, when using a standard monoethanolamine (MEA)-based solution with simple heat integration, the energy penalty to net generation would be 34%. The bulk of this was due to steam losses for regenerating solvent, followed by parasitic electrical demand for CO 2 compression and then by increased parasitic load for pushing flue gas through the absorber column. These demands could be decreased with a more advanced solvent that exhibits lower heat of regeneration and lower pressure drop than does a simple MEA solution. Further energy could be saved with more thorough heat integration to recover useful energy from the steam used for solvent regeneration. Installing a WESP was predicted to increase the cost of electricity by nearly $5/MWh. This would become cost-effective if solvent losses were roughly 10 times the baseline estimate when not using a WESP but could be returned to baseline by installing the WESP. Piping CO 2 for storage in more favorable geology could help with carbon capture and storage economics. Although storing off-site would necessitate construction of a CO 2 transport pipeline, the cost of this pipeline might be more than offset by reducing the number of wells required, the depths of the wells required, and the electrical demand for the CO 2 compressor. Additional factors that favor off-site storage costs include smaller expected CO 2 plume sizes, which translates to less monitoring and fewer landowner agreements. More detailed assessment of the specific geology in the region under and around Coal Creek Station would be needed to accurately assess the costs and benefits of different storage site options. This subtask was cofunded through the Energy & Environmental Research Center–U.S. Department of Energy Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233. Nonfederal funding was provided by the North Dakota Industrial Commission.

Strege, Joshua↗
DOE OSTI2017

Low-temperature atomic layer deposition of CuSbS 2 for thin-film photovoltaics

Copper antimony sulfide (CuSbS 2 ) has been gaining traction as an earth-abundant absorber for thin-film photovoltaics given its near ideal band gap for solar energy conversion (~1.5 eV), large absorption coefficient (>10 4 cm –1 ), and elemental abundance. Through careful in situ analysis of the deposition conditions, a low-temperature route to CuSbS 2 thin films via atomic layer deposition has been developed. After a short (15 min) post process anneal at 225 °C, the ALD-grown CuSbS 2 films were crystalline with micron-sized grains, exhibited a band gap of 1.6 eV and an absorption coefficient >10 4 cm –1 , as well as a hole concentration of 10 15 cm –3 . Finally, the ALD-grown CuSbS 2 films were paired with ALD-grown TiO 2 to form a photovoltaic device. This photovoltaic device architecture represents one of a very limited number of Cd-free CuSbS 2 PV device stacks reported to date, and it is the first to demonstrate an open-circuit voltage on par with CuSbS 2 /CdS heterojunction PV devices. As a result, while far from optimized, this work demonstrates the potential for ALD-grown CuSbS 2 thin films in environmentally benign photovoltaics.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Reasoning Service Exemplars for NASA’s Data and Reasoning Fabric

Future operations for Urban and Advanced Air Mobility are enabled by a distributed network of reliable and secured data and reasoning services referred to here as a fabric. In the aggregate, such a system must be all encompassing and mission agnostic, but specific use-cases are still needed to improve understanding and drive design paradigms. For this purpose, three reasoning service exemplars for Target Selection and Routing, Trajectory Generation, and Battery Health Management were developed and integrated into a specific NASA proposed data and reasoning fabric. These services were then used to build a mission reasoning application for lightning strike reconnaissance developed in collaboration with the Civil Air Patrol. Autonomous mission execution was then demonstrated using a multivehicle simulation platform with a full envelope 6 Degree-of-Freedom dynamics model for a concept electric Vertical Takeoff and Landing aircraft.

Autonomy↗
DOE OSTI2022

Transience of the Retinal Output Is Determined by a Great Variety of Circuit Elements

Retinal ganglion cells (RGCs) encrypt stimulus features of the visual scene in action potentials and convey them toward higher visual centers in the brain. Although there are many visual features to encode, our recent understanding is that the ~46 different functional subtypes of RGCs in the retina share this task. In this scheme, each RGC subtype establishes a separate, parallel signaling route for a specific visual feature (e.g., contrast, the direction of motion, luminosity), through which information is conveyed. The efficiency of encoding depends on several factors, including signal strength, adaptational levels, and the actual efficacy of the underlying retinal microcircuits. Upon collecting inputs across their respective receptive field, RGCs perform further analysis (e.g., summation, subtraction, weighting) before they generate the final output spike train, which itself is characterized by multiple different features, such as the number of spikes, the inter-spike intervals, response delay, and the rundown time (transience) of the response. These specific kinetic features are essential for target postsynaptic neurons in the brain in order to effectively decode and interpret signals, thereby forming visual perception. We review recent knowledge regarding circuit elements of the mammalian retina that participate in shaping RGC response transience for optimal visual signaling.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Technoeconomic Analysis of the Electrochemically Mediated Amine Regeneration CO 2 Capture Process

The electrochemically mediated amine regeneration (EMAR) process presents an alternative route to the conventional thermal amine regeneration for carbon capture from a flue gas source. In this study, we conducted an economic analysis on the EMAR system for postcombustion CO2 capture from a 550 MWe power plant capturing 3.1 MtCO2 annually and from a mini steel mill with annual capture close to 170 ktCO2. We followed the recommendation of the National Energy Technology Laboratory (NETL) 2010 report to estimate the cost of CO2 avoided ([$/tCO2]). Detailed cost modeling of the electrochemical separation stage was conducted. This is integrated with the entire process flowsheet (e.g., including absorber, compressor, pumps, and other auxiliary equipment). Here, we identified the membrane cost as the dominant capital cost for the electrochemical separation train. At a membrane unit price of less than 10/m2, the CO2 capture cost can be reduced to below 50/tCO2 with optimized process conditions (e.g., desorption pressure and utilization of waste heat). Improvements in process design, cell construction, and solvent formulation may lead to additional reductions in the CO2 capture cost.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Driving Zn-MnO2 grid-scale batteries: A roadmap to cost-effective energy storage

Highlights Zn-MnO 2 batteries promise safe, reliable energy storage, and this roadmap outlines a combination of manufacturing strategies and technical innovations that could make this goal achievable. Approaches such as improved efficiency of manufacturing and increasing active material utilization will be important to getting costs as low as $100/kWh, but key materials innovations that facilitate the full 2-electron capacity utilization of MnO 2 , the use of high energy density 3D electrodes, and the promise of a separator-free battery with greater than 2V potential offer a route to batteries at $50/kWh or less. Abstract Large-scale energy storage is certain to play a significant, enabling role in the evolution of the emerging electrical grid. Battery-based storage, while not a dominant form of storage today, has opportunity to expand its utility through safe, reliable, and cost-effective technologies. Here, secondary Zn–MnO 2 batteries are highlighted as a promising extension of ubiquitous primary alkaline batteries, offering a safe, environmentally friendly chemistry in a scalable and practical energy dense technology. Importantly, there is a very realistic pathway to also making such batteries cost-effective at price points of $50/kWh or lower. By examining manufacturing examples at the Zn–MnO 2 battery manufacturer Urban Electric Power, a roadmap has been created to realize such low-cost systems. By focusing on manufacturing optimization through reduced materials waste, scalable manufacturing, and effective materials selection, costs can be significantly reduced. Ultimately, though, coupling these approaches with emerging research and development advances to enable full capacity active materials utilization and battery voltages greater than 2V are likely needed to drive costs below a target of $50/kWh. Reaching this commercially important goal, especially with a chemistry that is safe, well-known, and reliably effective stands to inject Zn–MnO 2 batteries in the storage landscape at a critical time in energy storage development and deployment. Graphical abstract

Spoerke, Erik D. (ORCID:0000000322862560)↗
DOE OSTI2016

DragonView: Toward Understanding Network Interference in Dragonfly-based Supercomputers

Acquiring and maintaining high performance computing systems represents a substantial, long term investment. Therefore, it is paramount to optimize their utilization in order to maximize the return on investment and the impact on science and engineering. In this context, network congestion and inter-job interference are a major challenge as they can lead to significant systemwide performance degregation. This is especially pertinent in shared interconnects such as the dragonfly network, in which resources are shared by multiple jobs. Since many large-scale applications are communication-bound, a few communication heavy applications can have a large impact on the performance of all jobs and decrease the overall system throughput. In this paper, we describe a web-based visual analytics environment to study congestion and inter-job interference on dragonfly networks. The system enables network architects, system administrators and application developers to explore the potential impact of machine configuration, job placement policies and routing algorithms by visualizing and comparing ensembles of simulated workloads and real world data. We focus on the design of the system and describe the challenges, design decisions and the final implementation. Finally, we present two detailed case studies of prototypical analysis sessions by our stakeholders aimed at exploring the implications of different workloads and machine configurations using ensembles of network simulations.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2018

Core-shell structured α-Fe2O3@CeO2 heterojunction for the enhanced visible-light photocatalytic activity

Highlights: • CeO{sub 2}–coated α-Fe{sub 2}O{sub 3} sample was prepared via a hydrothermal route. • α-Fe{sub 2}O{sub 3}@CeO{sub 2} presented the excellent photocatalytic activity and stability. • The heterojunction interface facilitated the separation of electron-hole pairs. • Ce{sup 4+}/Ce{sup 3+} redox couple promoted the efficient electron transfer. - Abstract: CeO{sub 2}-coated α-Fe{sub 2}O{sub 3} nanoparticles (α-Fe{sub 2}O{sub 3}@CeO{sub 2}) with the enhanced photocatalytic activity were synthesized by a hydrothermal route and performed for the visible light driven photo-degradation of methylene blue (MB). The photocatalytic activity of α-Fe{sub 2}O{sub 3}@CeO{sub 2} is greatly affected by the thickness of CeO{sub 2} shell under the same conditions. The core-shell structured α-Fe{sub 2}O{sub 3}@CeO{sub 2} sample exhibited a narrower band gap energy in comparison to the pure α-Fe{sub 2}O{sub 3} and CeO{sub 2} bulks, leading to the excellent photocatalytic activity and stability for the degradation of MB under visible light irradiation after five cycle times. The core-shell structured α-Fe{sub 2}O{sub 3}@CeO{sub 2} sample presented higher degradation activity than that of the supported 8-Fe/CeO{sub 2} bulks with optimized α-Fe{sub 2}O{sub 3} loading of 8%. It can be ascribed to the Ce{sup 4+}/Ce{sup 3+} redox couple and the heterojunction interfaces of core-shell structured α-Fe{sub 2}O{sub 3}@CeO{sub 2} sample, which can promote the electrons transfer and restrain the photoexcited electron-hole recombination, leading to the excellent degradation activity under visible light irradiation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2007

Reversible Intercalation of Fluoride-Anion Receptor Complexes in Graphite

We have demonstrated a route to reversibly intercalate fluoride-anion receptor complexes in graphite via a nonaqueous electrochemical process. This approach may find application for a rechargeable lithium-fluoride dual-ion intercalating battery with high specific energy. The cell chemistry presented here uses graphite cathodes with LiF dissolved in a nonaqueous solvent through the aid of anion receptors. Cells have been demonstrated with reversible cathode specific capacity of approximately 80 mAh/g at discharge plateaus of upward of 4.8 V, with graphite staging of the intercalant observed via in situ synchrotron X-ray diffraction during charging. Electrochemical impedance spectroscopy and B-11 nuclear magnetic resonance studies suggest that cointercalation of the anion receptor with the fluoride occurs during charging, which likely limits the cathode specific capacity. The anion receptor type dictates the extent of graphite fluorination, and must be further optimized to realize high theoretical fluorination levels. To find these optimal anion receptors, we have designed an ab initio calculations-based scheme aimed at identifying receptors with favorable fluoride binding and release properties.

electrolytes↗
NASA NTRS2023

Performance Modeling of Urban Air Mobility Vehicles to Support Air Traffic Management Research

The recent emergence of Urban Air Mobility (UAM) vehicles has resulted in a need for flight performance models that enable comprehensive simulation-based research on air traffic management topics such as route structure, scheduling, and separation standards. Successful performance modeling methods exist for a wide range of traditional aircraft designs. However, comparable modeling methods appropriate for UAM vehicles that combine fixed-wing and rotorcraft performance have not yet been established. One challenge to progress has been the lack of available data capturing the performance characteristics and unique flight profiles of these aircraft. This paper describes methods used to generate the required performance data and the development of performance models for UAM vehicles. Included is a review of the energy and power equations often used in developing performance models for traditional aircraft as well as a discussion of their applicability to UAM vehicles. The challenge of generating realistic performance data in over-actuated vehicles transitioning from hover to cruise flight is also addressed through an approach based on objective function optimization. A table-based performance model format adapted to UAM configurations is described, as well as parametric models intended to accompany the performance table to allow detailed modeling of power and fuel consumption during accelerated flight, turning flight, or flight at an arbitrary climb or descent rate. A discussion of future work is also provided, including the need for refinement of UAM performance modeling methods and formats, especially in conjunction with improvements to aerodynamic modeling of vehicles with complex designs where strong interaction effects may dominate important regions of the flight envelope.

Performance Modeling↗